氢气预混层流燃烧球形膨胀火焰的拉伸研究

采用高速纹影系统和定容燃烧弹对氢气预混层流燃烧球形膨胀火焰的拉伸进行了研究.分别改变燃空当量比(0.3～4.0)、初始温度(283～400,K)、初始压力(0.05～0.30,MPa)的条件下对比分析拉伸的变化规律,以及拉伸对火焰速度、燃烧速度的影响规律,还解释了拉伸对不等扩散不稳定和流体力学不稳定的影响机理.研究结果表明,随着半径的增大,拉伸率成幂函数关系逐渐减小,其指数和系数值随燃空当量比、温度、压力的变化有明显的变化规律;火焰拉伸的存在使得火焰速度和燃烧速度发生改变,同时它还是火焰不等扩散不稳定和流体力学不稳定发生的前提条件.     

初始压力对天然气-氢气-空气混合气火焰传播特性的影响

使用定容燃烧弹研究了不同初始压力下天然气-氢气-空气混合气的火焰传播规律,得到了初始压力、掺氢比和燃空当量比对无拉伸层流燃烧速率、质量燃烧流量的影响,结合高速纹影图片分析了影响火焰稳定性的因素(马克斯坦长度、火焰面两侧密度比和火焰厚度).结果表明,掺氢天然气无拉伸层流燃烧速率以及火焰的不稳定性受掺氢比、初始压力和燃空当量比的综合影响.结合高速纹影图片,得出火焰的稳定性会随初始压力的增加而减小;在相同的燃空当量比和掺氢比下,初始压力对密度比的影响不大,但是对火焰厚度的影响比较明显.     

二乙醚-空气预混合气层流燃烧速率测定

在定容燃烧弹内利用高速纹影摄像法系统地研究了不同初始压力、不同初始温度和不同燃空当量比下二乙醚-空气预混合气的层流燃烧特性。利用球形发展火焰分析得到了不同初始压力、不同初始温度和不同燃空当量比下二乙醚-空气预混合气的无拉伸层流火焰燃烧速率、马克斯坦长度等层流燃烧参数。研究结果表明:无拉伸层流火焰燃烧速率随初始温度的增加而增加,随初始压力的增加而降低;马克斯坦长度随着初始温度的增加而减小,随初始压力的增加而减小,随当量比的增加而减小,表明火焰前锋面不稳定性随初始温度和初始压力的增加而增加,随混合气浓度的增加而增加。基于试验数据获得了二乙醚-空气预混合气无拉伸层流燃烧速率的关系式。     

高温高压条件下乙醇-空气-稀释气预混合气层流燃烧特性研究

利用定容燃烧弹和高速纹影摄像手段研究了不同初始压力、初始温度、气体稀释度和燃空当量比下乙醇-空气-稀释气预混层流燃烧特性的基础特征参数,如绝热火焰温度、层流燃烧速度、层流燃烧质量流量、层流燃烧火焰厚度和已燃气体Markstein长度。研究结果表明:在给定初始压力、初始温度和气体稀释度的情况下,绝热火焰温度、质量燃烧流量和层流燃烧速度的最大值均出现在当量比1.0～1.1,层流火焰厚度在当量比1.1处取得最小值;已燃气体Markstein长度随当量比的增加呈下降趋势;在给定当量比条件下,绝热火焰温度随初始压力、初始温度的增加而增加,随氮气稀释度的增加而降低;层流燃烧速度随初始压力和氮气稀释度增加而降低,随初始温度增加而增加;层流质量燃烧流量随初始压力和初始温度的增加而增加;随氮气稀释度增加而减小;层流火焰厚度和已燃气体Markstein长度随初始压力和初始温度的增加而减小,随氮气稀释度的增加而增加。     

高温高压下二甲醚—空气预混层流燃烧特性研究

在定容燃烧弹内研究了初始压力为0.5 MPa时,不同初始温度和燃空当量比下二甲醚-空气混合气预混层流火焰的层流燃烧速率和马克斯坦长度,分析了火焰拉伸对火焰传播速率的影响.基于容弹燃烧的双区模型计算了预混层流燃烧的燃烧特性参数.结果表明:随着初始温度的增加,二甲醚-空气预混合气的无拉伸火焰传播速率和无拉伸层流燃烧率增加;对于给定的初始温度,在化学当量比偏浓混合气一侧存在一个层流燃烧速度的峰值;随初始温度和当最比增加,马克斯坦长度值减小,火焰前锋面的不稳定性增加;最大燃烧压力随初始温度的增加而下降,压力升高率随初始温度的增加而降低.     

不同初始压力下掺氢天然气的燃烧特性

在定容燃烧弹内研究了不同初始压力下天然气-氢气-空气混合气的火焰传播规律,得到了不同掺氢比例和初始压力下,不同燃空当量比时混合气的层流燃烧速率,并分析了火焰的稳定性及其影响因素.研究结果表明,随着天然气中掺氢比例的增加,混合气的燃烧速率增加,且增长速率逐渐加快,而马克斯坦长度值则随着掺氢比例的增加而减小,即火焰的稳定性下降.不同初始压力下,随着燃空当量比的增加,马克斯坦长度值在不同掺氢比例下均增加,显示火焰的稳定性增加.无拉伸层流燃烧速率随着初始压力的增加略有减小,且在化学当量比附近,变化的初始压力和掺氢比对无拉伸层流燃烧速率的影响最为明显.     

仲丁醇-空气预混层流燃烧速度的研究

基于定容燃烧弹,利用纹影法和球型火焰扩散法研究了不同燃空当量比、环境温度和环境压力下仲丁醇-空气预混层流燃烧速度.通过对仲丁醇-空气拉伸层流火焰传播速度与拉伸率之间关系的分析,获得了无拉伸火焰层流燃烧速度和马克斯坦长度.研究结果表明:随着环境压力的上升,仲丁醇-空气层流燃烧速度降低,马克斯坦长度降低,火焰不稳定性增加;随着环境温度的增加,无拉伸层流燃烧速度增加,马克斯坦长度减小,表明燃烧火焰不稳定性增加;随着燃空当量比的增加,马克斯坦长度减小,火焰不稳定性增加;燃空当量比Φ=1.1左右时,火焰传播速度和无拉伸层流燃烧速度达到最大值.     

甲醇-空气-氮气混合气预混球型火焰的试验研究

利用高速纹影摄像法在定容燃烧弹内研究了不同燃空当最比、初始压力、初始温度和气体稀释度下甲醇-空气-氮气混合气预混球型火焰的发展特性以及3种火焰锋面的不稳定性.获得了不同初始状态下的层流燃烧速度、质量燃烧流量和马克斯坦长度.高的初始压力时,火焰锋面生成的裂纹发展并形成细胞状结构.稀混合气时,浮力和电极的冷却作用对火焰的发展有重要影响.当量比在化学计量比附近时,随着初始温度的提高,流体动力学不稳定性被抑制.随着初始压力的增加,流体动力学不稳定性增强.稀释气的加入抑制了火焰锋面流体动力学的不稳定性.     

天然气/氢气燃烧特性研究

在定容燃烧弹中研究了不同氢气掺混比例、燃空当量比和初始压力下的大然气／氢气混合气的燃烧特性,建立了适合用于容弹计算的准维双区模型。研究结果表明：在各种当量比和初始压力下,随着掺氢比例的增加,混合气的质量燃烧速率明显增加,燃烧持续期和火焰发展期娃著缩短。随着掺氢比例的增加,短的燃烧持续期所对应的当量比范围变宽,稀混合气和浓混合气条件下天然气掺氢对火焰发展期缩短的效果更明显。化学计量比附近（1．0—1．1）掺氢燃烧对燃烧最大压力值影响不大,浓混合气（燃空当量比大于1．1）和稀混合气燃烧时,随着掺氢比例的增加,最大燃烧压力值增加。     

二甲醚均质压缩燃烧的数值模拟研究

采用最新的二甲醚(DME)化学动力学反应机理(DME氧化机理包括399个基元反应,涉及79种组分),利用LawrenceLivermore国家实验室开发的HCT软件,进行DME均质充量压燃着火过程的变参数研究。从理论上分析讨论进气温度、进气压力、燃空当量比、发动机转速对燃烧的影响。研究结果表明:DME的均质充量压燃(HCCI)燃烧过程有明显的两阶段,进气温度、进气压力、燃空当量比和发动机转速等参数的改变都会导致DME均质压缩燃烧过程的变化。     

小型锅炉烟尘测试时锅炉出力的计算

锅炉烟尘测试时,必须对锅炉出力进行测试。但监测中,许多小型锅炉往往不具备相关的计量装置和仪表,为解决这一问题,文章提出了用烟气量和空气过剩系数来计算锅炉的出力的公式,在实际使用中,该方法简单易行,其结果和实测值具有很好的一致怀。     

Unerroric of control of mutual compliance of the efficiency of hydrogen engines of unmanned vehicles in the conditions of mass production

The issues related to the reliability of hydrogen engines of unmanned vehicles and increasing the efficiency of using hydrogen as fuel when using the method of its production during the decomposition of hydrogen-containing molecules of liquid-phase organic compounds in a plasma discharge under the action of intense ultrasonic exposure are considered. Experiments have shown that as a result of decomposition in the acoustoplasma discharge of liquid hydrocarbons, solid-phase carbon-containing products are formed, chemical transformations occur in the liquid phase and hydrogen-containing combustible gas is formed. Hydrogen-containing gas can be used as fuel immediately after synthesis, i.e. it does not require separation, since in addition to hydrogen it contains only impurities of CO₂ and water vapor. The purpose of the study is to formalize the basic conditions for tightening the control of mutual compliance with the efficiency of hydrogen engines of the same series in the conditions of their mass production. Methods of mathematical statistics and hardware-software modeling were used in the study. The term “unerroric of quality mutual compliance control” is introduced to describe a set of hardware and software tools for such control. The principle of in-depth testing of the technical condition of such engines of one series is described in a multidimensional formulation of the quality control problem for three of their operating parameters at once. The conditions for increasing the mutual correspondence of the measured values of such parameters in the conditions of serial production of hydrogen engines are formalized.     

中国煤炭地下气化技术的发展

本文综述了煤炭地下汽化技术的国内外发展现状,对我国“长通道、大断面”煤炭地下气化新工艺给予了技术经济评述,并提出了发展煤炭地下汽化技术的政策建议。     

Review of theory of distortion and disintegration of liquid streams

Linear and nonlinear analyses of the instabilities and distortion of liquid streams injected into a gaseous media are discussed. The various fundamental mechanisms and the predictive capabilities for the distortions are emphasized. Round jets, planar sheets, annular sheets, and conical sheets are discussed in detail. The balance between capillary and inertial forces is primarily examined. The method for simplifying the analyses in the case of thin liquid sheets is discussed. The capabilities for representing the droplet size distribution that follows the stream disintegration are outlined.     

MgO膨胀剂细度对MgO水化和水泥浆体膨胀的影响

基于《水工混凝土掺用氧化镁技术规范》中的Ⅰ型氧化镁（MgO）,研究了该型MgO膨胀剂（MEA）细度对掺粉煤灰水泥浆体膨胀性能的影响。即采用X射线衍射分析(XRD)及同步热分析（TG DSC）分析了掺MEA水泥浆体中MgO的水化性。结果表明,养护温度相同时,MEA的细度对水泥浆体内MEA中MgO的水化和水泥浆体的膨胀无显著影响,产生的膨胀均能补偿水泥浆体的收缩;MEA的细度可从试验设计采用的45 μm筛筛余15%左右增加到30%左右,这将有利于MEA生产企业的节能降耗。     

机车车轮多轴疲劳强度安全评定的研究

使用ANSYS8.0软件对高速列车车轮进行了三维有限元分析,计算出车轮在直线、曲线和道岔条件下牵引、制动共6种工况时孔边薄弱部位的应力,分别通过Mises等效平均应力方法、Sines平均主应力方法和应力分量中考虑平均应力方法计算出应力在极值位置时的等效应力幅、等效平均应力,从而进一步算出车轮的安全系数,对其疲劳强度进行评定,并对3种方法进行了比较研究。     

Constructal optimization of the geometry of an array of micro-channels

This paper documents the geometric optimization of an array of circular and non-circular ducts. The optimization was carried out numerically using finite volume method. As optimal dimensions were independent of the array configuration, the numerical simulation was performed on a unit cell. Numerical optimization for circular, square and isosceles right triangle cross-sections of channels was performed. Based on the results of this investigation, some correlations were proposed to predict the optimal hydraulic diameter and dimensionless heat transfer per unit volume. In addition to examining the effect of pressure drop on these parameters, it was showed that among the different geometries of this study, square cross-section has the most efficiency for a given volume. The numerical results of the present study were compared with approximate results reported in the literature which a good agreement was observed.     

固体热辐射Yong性能分析

本文对漫灰均温物体在常物性条件下对外辐射传热的Ｙｏｎｇ值计算建立了数学模型。通过与物体内能Ｙｏｎｇ公式的数值计算比较,得出了辐射能量的Ｙｏｎｇ值不大于内能Ｙｏｎｇ值的结论。从初步的热射Ｙｏｎｇ值计算公式发现。Ｙｏｎｇ与物体表面辐射率有关。     

Measurements of concentration distribution of hydrogen jet using deflection of center of the laser spot

The main purpose of this work is to propose a new method to evaluate the concentration distribution of the hydrogen jet by using a He–Ne laser through the jet. This research attempts to apply the expression of concentration Gaussian distribution, the refraction formula of inhomogeneous refractive index medium, and the concentration inversion function to disclose the displacement of the center of the laser spot at different heights in the gas jet. The spot images of the laser beam passing through the gas jet at three vertical heights z = 10d, 20d, 30d, and different radial positions are obtained. The radial spatial asymmetry of the gas jet is also found in the experiment. Finally, the calculated concentration distribution curve and the fluent simulation curve, it is found that the two results are very similar. Our findings show that the error between the concentration distribution of this method and the simulated concentration distribution reaches 2.43%.     

Heat of vaporization of mixtures

General expressions for the heat of vaporization of mixtures at constant pressure; at constant temperature; and at constant pressure, temperature, and composition are proposed. The last one is related to the liquid-vapor interface where steady vaporization or condensation is taking place. Numerical examples by the proposed expressions are shown for binary mixtures of HCFC22(R22) and (HCFC123(R123) © 1997 Scripta Technica, Inc. Heat Trans Jpn Res, 25(1): 12–24, 1996