Fe2+催化H2O2、S2O82-、S2O82--H2O2降解橙黄G

以偶氮染料橙黄G(OG)为目标污染物,研究Fe2+分别催化H2O2、S2O82-、H2O2-S2O82-降解0.1 mmol/LOG Fe2+/H2O2体系,[Fe2+]=1 mmol/L,pH=3,[H2O2]0=10 mmol/L,降解30 min OG脱色率为96%,随着pH值增大和[H2O2]0>10 mmol/L,OG脱色率减小,呈线性变化。Fe2+/S2O82-体系,随着S2O82-初始浓度增加OG脱色率增大,随着pH值增大OG脱色率减小,呈非线性变化。Fe2+/H2O2-S2O82-体系,pH=3,[H2O2]0=2 mmol/L,[S2O82-]0>10 mmol/L时OG脱色率持续增大。Fe2+/H2O2-S2O82-体系矿化率最高。利用乙醇和硝基苯作为分子探针,采用分子探针竞争实验鉴定该体系中产生的SO4.和OH.。     

PbBr2-PbCl2-PbF2-PbO-P2O5系统 玻璃性能研究

研究了PbBr     

固体超强酸催化剂S2O82-/ZrO2-TiO2-Al2O3制备乙酰丙酸

研制了固体超强酸催化剂S2O82―/ZrO2-TiO2-Al2O3,并以蔗糖为原料,催化水解法制备乙酰丙酸。通过单变量法考察了催化剂的焙烧温度、催化剂的投加量、蔗糖浓度、反应温度、反应时间等对乙酰丙酸相对收率的影响,并采用了正交实验来确定最佳工艺条件。研究结果表明,当催化剂的焙烧温度为550℃、蔗糖浓度为15 g/L、催化剂用量为蔗糖质量的15%、反应温度为200℃、反应时间为60 min时,乙酰丙酸的相对收率最大,达到72.28%。     

Na2O-TiO2-SiO2-CaO-Al2O3-V2O5-MnO-MgO-FeO渣系渣铁间硫分配比热力学模型

基于离子分子共存理论(IMCT)建立了Na₂O-TiO₂-SiO₂-CaO-Al₂O₃-V₂O₅-MnO-MgO-FeO九元渣系的结构单元作用浓度模型和渣铁间硫分配比热力学模型,并对模型进行实验验证。通过模型计算出1200℃下渣系主要结构单元组成和渣中Na₂O,CaO,MnO,MgO和FeO的活度,发现Na₂O的加入可促进渣中低熔点物质的生成,降低渣系熔化性温度,改善脱硫反应的动力学条件;同时随着Na₂O加入量的增加,渣中Na₂O和CaO的活度增加,进而降低渣中S^2?离子活度,强化渣铁间脱硫反应。实验结果表明,增加碱矿比提高了渣铁间硫分配比,有利于铁水深度脱硫,铁水中硫含量可降至0.0005wt%以下,硫分配比的理论计算值与实验结果吻合极好。渣中各碱性氧化物的硫分配比随碱矿比R_N/C增加逐渐增大,各碱性氧...     

CO2-H2O和CO2-H2O-NaCl 体系的相平衡研究进展

To study the feasibility of CO2 geological sequestration,it is needed to understand the complicated mul- tiple-phase equilibrium and the densities of aqueous solution with CO2 and multi-ions under wide geological condi- tions（273.15—473.15K,0—60MPa）,which are also essential for designing separation equipments in chemical or oil-related industries.For this purpose,studies on the relevant phase equilibria and densities are reviewed and analyzed and the method to improve or modify the existing model is suggested in order to obtain more reliable predictions in a wide temperature and pressure range.Besides,three different models（the electrolyte non random two-liquid（ELECNRTL）,the electrolyte NRTL combining with Helgeson model（ENRTL-HG）,Pitzer activity coefficient model combining with Helgeson model（PITZ-HG））are used to calculate the vapor-liquid phase equilib- rium of CO2-H2O and CO2-H2O-NaCl systems.For CO2-H2O system,the calculation results agree with the experimental data very well at low and medium pressure（0—20MPa）,but there are great discrepancies above 20MPa.For the water content at 473.15K,the calculated results agree with the experimental data quite well.For the CO2-H2O-NaCl system,the PITZ-HG model show better results than ELECNRTL and ENRTL-HG models at the NaCl concentration of 0.52mol·L ^-1 .Bur for the NaCl concentration of 3.997mol·L ^-1 ,using the ELECNRTL and ENRTL-HG models gives better results than using the PITZ-HG model.It is shown that available experimental data and the thermodynamic calculations can satisfy the needs of the calculation of the sequestration capacity in the temperature and pressure range for disposal of CO2 in deep saline aquifers.More experimental data and more accurate thermodynamic calculations are needed in high temperature and pressure ranges（above 398.15K and 31.5MPa）.     

Al2O3-3Al2O3·2SiO2-ZrO2耐火材料的相组成

Al2O3-SiO2-ZrO2系耐火材料应用范围广,特别被用作陶瓷辊,具有力学强度高、抗热震性能优良、耐碱类化合物侵蚀和高温蠕变率低的特性。Al2O3-SiO2-ZrO2系耐火材料性能很大程度上取决于其结晶相和玻璃相的总量和化学成分,采用定量XRPD和XRF研究了原料中Al2O3/SiO2比和氧化铝颗粒尺寸分布对结晶相和玻璃相的总量及其化学成分的影响。耐火材料由莫来石、刚玉、ZrO2的多晶体和总量各异的玻璃相组成。莫来石含量及其晶胞参数和成分随烧成温度改变,但主要受原料中Al2O3/SiO2比的影响。     

Na2O-CaO-Al2O3-B2O3-SiO2-TiO2体系分相过程中两相组成的变化

研究了Na2O-CaO-Al2O3-B2O3-SiO2-TiO2体系分相过程中两相组成的变化。采用扫描电镜测试、能谱分析和X射线衍射等手段对在不同温度下热处理的试样进行测试。实验结果表明,试样发生相分离后,分离成富碱硼相和富硅相,两相的化学组成随分相温度呈现一定的变化。当热处理温度从700℃升高至850℃时,富碱硼相量增加,玻璃分相程度增大。分相温度较低时,富碱硼相中的网调整氧化物只有氧化钙,而网调整氧化物氧化钠集结在富硅相中。随分相温度的升高,氧化钙仍保持在富碱硼相中,而氧化钠则由在富硅相中集聚逐步转移至在富碱硼相中。在分相过程中二氧化钛在分相界面处集聚并析出。     

FeS2-H2SO4-H2O体系浸出锰阳极泥

研究了搅拌速率,黄铁矿用量,硫酸浓度,反应温度以及锰阳极泥的颗粒半径对锰浸出率的影响。实验结果表明,当反应温度为85℃,搅拌速率为500 r/min,颗粒半径小于0.15mm,锰阳极泥、黄铁矿、硫酸的质量比为1∶0.75∶0.92时,锰的浸出率可以达到93%。     

S2O2－8/Fe2O3-ZrO2-SiO2固体酸催化剂合成马来酸二己酯

在铁锆氧化物中引入硅的氧化物，并用S₂O^2－₈浸渍铁锆硅复合氧化物，制得较S₂O^2－₈/Fe₂O₃-ZrO₂（PSFZ）和SO^2－₄/Fe₂O₃-ZrO₂-SiO₂（SFZS）催化活性更强的固体酸催化剂S₂O^2－₈/Fe₂O₃-ZrO₂-SiO₂（PSFZS），研究获得最佳制备条件。用马来酸酐与正己醇的酯化反应考察了催化剂活性。XRD和TEM结果表明，制备的催化剂S₂O^2－₈对铁锆硅复合氧化物的促进作用明显好于SO^2－₄；SiO₂ 和Fe₂O₃的引入使催化剂呈现多孔结构，分散性好，其稳定性增加，催化活性提高；用该催化剂代替硫酸和对甲苯磺酸用于催化马来酸酐和正己醇的酯化反应，可得无色透明的酯化产物，3 h内酯化率达97.9%，分别比PSFZ和PSFZS催化剂提高约10%20%。     

Crystallization of zeolite L from Na2O-K2O-Al2O3-SiO2-H2O system

Zeolite L powder was prepared from the substrate mixture of Na₂O-K₂O-Al₂O₃-SiO₂-H₂O system at temperatures of 373-443 K. In order to investigate the factors which influence the synthesis outcome, a reference system which yields zeolite L in a reproducible manner was chosen and subjected to controlled changes in synthesis parameters. The crystalline zeolite L samples obtained were characterized by elemental chemical analysis, X-ray diffraction (XRD), and scanning electron microscopy (SEM). It was established that phase purity, morphology, and the size of crystals of crystalline product were affected by molar ratios of the substrate, such as SiO₂/Al₂O₃, (K₂O+Na₂O)/SiO₂, Na₂O/(K₂O+Na₂O), and H₂O/(K₂O+Na₂O). Amorphous silica powder (Zeosil) was the preferred silica source, and the crystallization rate was promoted by introducing gel aging, seeding, and rapid heating rate.     

Photocatalytic activity of Cu2O/TiO2, Bi2O3/TiO2 and ZnMn2O4/TiO2 heterojunctions

Cu₂O/TiO₂, Bi₂O₃/TiO₂ and ZnMn₂O₄/TiO₂ heterojunctions were studied for potential applications in water decontamination technology and their capacity to induce an oxidation process under VIS light. UV–vis spectroscopy analysis showed that the junctions-based Cu₂O, Bi₂O₃ and ZnMn₂O₄ are able to absorb a large part of visible light (respectively, up to 650, 460 and 1000 nm). This fact was confirmed in the case of Cu₂O/TiO₂ and Bi₂O₃/TiO₂ by photocatalytic experiments performed under visible light. A part of the charge recombination that can take place when both semiconductors are excited was observed when a photocatalytic experiment was performed under UV–vis illumination. Orange II, 4-hydroxybenzoic and benzamide were used as pollutants in the experiment. Photoactivity of the junctions was found to be strongly dependent on the substrate. The different phenomena that were observed in each case are discussed.     

碳酸钠—过氧化氢—水体系相图的绘制

进行了Na2CO3-H2O2-H2O体系溶解度的测定并绘制成相图,最后对其应用进行了讨论。     

Synthesis and characterization of Y2O3-ZrO2 and Y2O3-CeO2-ZrO2 precursor powders

Thixotropic gels of the precursor powders of the titled compounds have been prepared by the addition of oxalic acid to the mixed solutions of metal salts at room temperature (≈ 27 °C). The clear sols of yttrium-zirconyl oxalate (YZO) and yttrium-cerium-zirconyl oxalate (YCZO) gelled within a few hours and were oven-dried at 40 °C. The various stages of gelation behaviour of the sols are explained on the basis of DLVO theory. By repeptizing the dried gel powders with water, concentrated sols were prepared. The gelation time as a function of chloride ion concentration is discussed for both sols. The nature of the temperature dependence of the dried gel powders was studied by means of thermogravimetric analysis and differential thermal analysis. Powder X-ray diffraction was used to study the crystallization behaviour of the dried amorphous gel powders. It is found that these powders crystallize in tetragonal phase when calcined at 850 °C for 1 h. Estimation of surface area and infra-red characterization have also been carried out for the prepared powders.     

Stable Ti/RuO2-Sb2O5-SnO2 electrodes for O2 evolution

RuO₂-based electrodes are generally known to be unstable for O₂ evolution. In this paper, a stable type of RuO₂-based electrode, Ti/RuO₂-Sb₂O₅-SnO₂, is demonstrated for O₂ evolution. In the ternary oxide coating, RuO₂ serves as the catalyst, SnO₂ as the dispersing agent, and Sb₂O₅ as the dopant. The accelerated life test showed that the Ti/RuO₂-Sb₂O₅-SnO₂ electrode containing 12.2 molar percent of RuO₂ nominally in the coating had a service life of 307 h in 3 M H₂SO₄ solution under a current density of 0.5 A cm⁻² at 25 °C, which is more than 15 times longer than other types of RuO₂-based electrodes. Instrumental analysis indicated that RuO₂-Sb₂O₅-SnO₂ was a solid solution with a compact structure, which contributed to the stable nature of the electrode.     

Preparation and characterization of Cr2O3-TiO2-Al2O3-V2O5 green pigment

Green pigments with high near infrared reflectance based on a Cr₂O₃-TiO₂-Al₂O₃-V₂O₅ composition have been synthesized. Cr₂O₃ was used as the host component and mixtures of TiO₂, Al₂O₃ and V₂O₅ were used as the guest components. TiO₂, Al₂O₃, and V₂O₅ were mixed into 39 different compositions. The spectral reflectance and the distribution of pigment powder were determined using a spectrophotometer and a scanning electron microscope, respectively. It was found that a pigment powder sample S9 with a Cr₂O₃-TiO₂-Al₂O₃-V₂O₅ composition of 80, 4, 14 and 2 wt%, respectively, gives a maximum near infrared solar reflectance of 82.8% compared with 49.0% for pure Cr₂O₃. The dispersion of pigment powders in a ceramic glaze was also studied. The results show that the pigment powder sample S9 is suitable for use as a coating material for ceramic-based roofs.     

Crystal Structure of the LiNaZnP2O7 Compound in the Li2ZnP2O7-Na2ZnP2O7 Glass-Forming System

The crystal structure of the LiNaZnP₂O₇ compound is determined using X-ray powder diffraction (space group Cmcm, a = 12.431 Å, b = 7.589 Å, c = 6.283 Å). The structure has a mixed tetrahedral framework consisting of the diortho groups [P₂O₇] and the tetrahedra [ZnO₄] and [LiO₄], which are joined into chains. The [ZnO₄] and [LiO₄] tetrahedra are distributed in the chains in a random manner, because the zinc and lithium atoms statistically occupy one crystallographic position. The sodium cations are arranged in channels of the tetrahedral framework. The atomic coordinates and interatomic distances in the structure are reported. Original Russian Text Copyright ? 2005 by Fizika i Khimiya Stekla, Shepelev, Lapshin, Petrova, Novikova.     

ZrO2/SiO2- and La2O3/Al2O3-supported platinum catalysts for CH4/CO2 reforming

Surface-phase ZrO₂ on SiO₂ (SZrOs) and surface-phase La₂O₃ on Al₂O₃ (SLaOs) were prepared with various loadings of ZrO₂ and La₂O₃, characterized and used as supports for preparing Pt/SZrOs and Pt/SLaOs catalysts. CH₄/CO₂ reforming over the Pt/SZrOs and Pt/SLaOs catalysts was examined and compared with Pt/Al₂O₃ and Pt/SiO₂ catalysts. CO₂ or CH₄ pulse reaction/adsorption analysis was employed to elucidate the effects of these surface-phase oxides.

The zirconia can be homogeneously dispersed on SiO₂ to form a stable surface-phase oxide. The lanthana cannot be spread well on Al₂O₃, but it forms a stable amorphous oxide with Al₂O₃. The Pt/SZrOs and Pt/SLaOs catalysts showed higher steady activity than did Pt/SiO₂ and Pt/Al₂O₃ by a factor of three to four. The Pt/SZrOs and Pt/SLaOs catalysts were also much more stable than the Pt/SiO₂ and Pt/Al₂O₃ catalysts for long stream time and for reforming temperatures above 700 °C. These findings were attributed to the activation of CO₂ adsorbed on the basic sites of SZrOs and SLaOs.     

Al2O3-SiO2-TiO2一ZrO2复合陶瓷膜的制备与表征

采用Sol—Gel法制备出掺杂SiO2，TiO2及ZrO2改性的γ-Al2O3膜，并通过SEM，EPMA，AFM等测试手段对膜结构和性能进行表征。探讨了制膜工艺条件对膜性能及结构的影响。制备的Al2O3复合膜膜厚为1—2μm，结构均匀无缺陷。     

Gas-solid oxidations with RuO2---TiO2 and RuO2---SiO2 membranes

The activity of the RuO₂---TiO₂ and RuO₂---SiO₂ membrane catalysts in oxidation with air of the isopropylic alcohol was determined at temperatures ranging from 40 to 120°C. The RuO₂---TiO₂ and RuO₂---SiO₂ membranes were prepared by the sol-gel process and supported on microporous glass membranes. The catalysts were characterized by scanning electron microscopy, IR spectroscopy and X-ray diffraction studies.