One-step synthesis of Li-doped NiO as high-performance anode material for lithium ion batteries

The poor electronic conductivity and huge volume expansion of NiO are the vital barriers when used as anode for lithium ion batteries. In order to solve above issues, Li-doped NiO are prepared by a facile one-step ultrasonic spray pyrolysis method. The effects of Li doping on the morphology, structure and chemical composition of the Li-doped NiO powders are extensively studied. When used as lithium ion batteries anode, it is demonstrated that the doping of Li has significant positive effect on improving the electrochemical performance. After 100 cycles at 400 mA g⁻¹, The Li-doped NiO samples deliver a discharge capacity of 907 mAh g⁻¹, much more than that of un-doped sample (736 mAh g⁻¹). The improved electrochemical performances can be ascribed to the improved p-type conductivity and lower impedance, which are confirmed by Rietveld refinement, X-ray photoelectron spectroscopy and electron impedance spectroscopy.     

Hematite nanoflakes as anode electrode materials for rechargeable lithium-ion batteries

Hematite (α-Fe₂O₃) nanoflakes and nanocubes were synthesized by liquid-solid-solution method and their properties as anode electrode materials for rechargeable Li⁺-ion batteries were measured. When changing the water to ethanol volume ratio in the synthesis system, the nanocrystals can be changed from α-Fe₂O₃ to α-FeOOH, with shapes being tuned from nanoflakes to nanocubes, non-uniform particles and nanowires. When assembled as the anode electrode materials in rechargeable Li⁺-ion batteries, the hematite nanoflakes showed one more plateau in the first discharge progress of the voltage-composition curves than hematite nanocrystals with other shapes in the literature. X-ray diffraction, high-resolution transmission electron microscope and electrochemical data showed that this extra plateau came from the formation of Li₂Fe₃O₄ nanoclusters and amorphous Li₂O. This experiment showed that like sizes, shapes of nanocrystals may also affect the detailed electrochemical progress.     

CuO/graphene composite as anode materials for lithium-ion batteries

CuO/graphene composite is synthesized from CuO and graphene oxide sheets following reduced by hydrazine vapor. As the electrode material for lithium-ion batteries, CuO nanoparticles with sizes of about 30 nm homogeneously locate on graphene sheets, and act as spacers to effectively prevent the agglomeration of graphene sheets, keeping their high active surface. In turn, the graphene sheets with good electrical conductivity server as a conducting network for fast electron transfer between the active materials and charge collector, as well as buffered spaces to accommodate the volume expansion/contraction during discharge/charge process. The synergetic effect is beneficial for the electrochemical performances of CuO/graphene composite, such as improved initial coulombic efficiency (68.7%) and reversible capacity of 583.5 mAh g⁻¹ with 75.5% retention of the reversible capacity after 50 cycles.     

Three-dimensional porous Sn-Cu alloy anode for lithium-ion batteries

A binder-free three-dimensional (3D) porous Cu₆Sn₅ anode was prepared for lithium-ion batteries. In this novel approach, tin was deposited by electroless-plating on copper foam which was served as anode current collector as well as the source of copper for Cu₆Sn₅ alloy formation. With optimized post-treatment condition, Cu₆Sn₅ alloy with thickness of 1.2 μm was formed on the surface of copper foam network. 3D porous Sn-Cu₆Sn₅ and Cu₃Sn-Cu₁₀Sn₃-Cu₆Sn₅ composite anodes were also prepared for comparison. Electrochemical tests showed that 3D porous Cu₆Sn₅ anode exhibits the best electrochemical performance in terms of specific capacitance and cycleability, which delivers a rechargeable capacity of 404 mAh g⁻¹ over 100 cycles.     

Hollow CuFe2O4 spheres encapsulated in carbon shells as an anode material for rechargeable lithium-ion batteries

We report here a polymer-templated hydrothermal growth method and subsequent calcination to achieve carbon coated hollow CuFe₂O₄ spheres (H–CuFe₂O₄@C). This material, when used as anode for Li-ion battery, retains a high specific capacity of 550 mAh g⁻¹ even after the 70th cycle, which is much higher than those of both CuFe₂O₄@C (∼300 mAh g⁻¹) and H–CuFe₂O₄ (∼120 mAh g⁻¹). And galvanostatic cycling at different current densities reveals that a capacity of 480 mAh g⁻¹, 91% recovery of the specific capacity cycling at 100 mA g⁻¹, can be obtained even after 50 cycles running from 100 to 1600 mA g⁻¹. The significantly enhanced electrochemical performances of H–CuFe₂O₄@C with regard to Li-ion storage are ascribed to the following factors: (1) the hollow void, which could mitigate the pulverization of electrode and facilitate the lithium-ion, electron and electrolyte transport; (2) the conductive carbon coating, which could enhance the conductivity, alleviate the agglomeration problem, prevent the formation of an overly thick SEI film and buffer the electrode. Such a structural motif of H–CuFe₂O₄@C is promising, for electrode materials of LIBs, and points out a general strategy for creating other hollow-shell electrode materials with improved electrochemical performances.     

One-dimensional core-shell composite of AgNWs@Si@GO for high-specific capacity and high-safety anode materials of lithium-ion batteries

Si/C composite materials used for Lithium-ion battery anode, have received widespread attention owing to theirs superior energy density, long cycle life, and low self-discharge efficiency. However, the unstable solid electrolyte interface (SEI) and severe volume expansion, occurring in lithiation-delithiation of silicon materials, are major obstacles to its commercial application. Here, we proposed a silver nanowire@silicon@graphene oxide (AgNWs@Si@GO) core-shell structure by introducing one-dimensional silver nanowire into reactive silicon material through an uncomplicated polyol method. The electrochemical properties of the prepared AgNWs@Si@GO composites were well characterized as the anode of Lithium-ion batteries (LIBs). The synthesized AgNWs@Si@GO composites exhibited exceptional electrochemical performance, high specific capacity (1384.8 mA h/g at 0.2 C) and improved cycle stability. The excellent electrical conductivity of AgNWs and the outstanding flexibility of GO makes AgNWs@Si@GO core-shell structure efficaciously alleviate the volume expansion of silicon-based materials in the process of lithiation, and further improve the cycle stability of electrode materials.     

In-situ synthesis of reduced graphene oxide wrapped Mn3O4 nanocomposite as anode materials for high-performance lithium-ion batteries

We report a novel in-situ symbiosis method to prepare reduced graphene oxide wrapped Mn₃O₄ nanoparticles (rGO/Mn₃O₄) with uniform size about 50 nm as anodes for lithium-ion batteries (LIBs), which can simplify the preparation process and effectively reduce pollution. The rGO/Mn₃O₄ nanocomposite exhibited a reversible specific capacity of 795.5 mAh g^?1 at 100 mA g^?1 after 200 cycles (capacity retention: 87.4%), which benefits from the unique structural advantages and the synergistic effect of rGO and Mn₃O₄. The Mn₃O₄ nanoparticles encapsulated among the rGO nanosheets exhibited good electrochemical activity, and the multilayer wrinkled rGO sheets provided a stable 3D conduction channel for Li⁺/e^? transport. The rGO/Mn₃O₄ nanocomposite is a promising anode candidate for advanced LIBs with excellent cycling performance and rate performance. Furthermore, this new preparation method can be extended to green and economical synthesis of advanced graphene/manganese-based nanocomposites.     

CuO/C microspheres as anode materials for lithium ion batteries

CuO/C microspheres are prepared by calcining CuCl₂/resorcinol-formaldehyde (RF) gel in argon atmosphere followed by a subsequent oxidation process using H₂O₂ solution. The microstructure and morphology of materials are characterized by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), and transition electron microscopy (TEM). Carbon microspheres have an average diameter of about 2 μm, and CuO particles with the sizes of 50–200 nm disperse in these microspheres. The electrochemical properties of CuO/C microspheres as anode materials for lithium ion batteries are investigated by galvanostatic discharge–charge and cyclic voltammetry (CV) tests. The results show that CuO/C microspheres deliver discharge and charge capacities of 470 and 440 mAh g⁻¹ after 50 cycles, and they also exhibit better rate capability than that of pure CuO. It is believed that the carbon microspheres play an important role in their electrochemical properties.     

Synthesis of TiO2(B)/SnO2 composite materials as an anode for lithium-ion batteries

A TiO₂(B) nanosheets/SnO₂ nanoparticles composite was prepared by the hydrothermal and chemical bath deposition (CBD) methods, and its electrochemical properties were investigated for use as the anode material of a lithium-ion battery. The as-prepared composites consisted of monoclinic-phase TiO₂(B) nanosheets and cassiterite structure SnO₂ nanoparticles, in which SnO₂ nanoparticles were uniformly decorated on the TiO₂(B) nanosheets. The TiO₂(B)/SnO₂ composites showed a higher reversible capacity and better durability than that of the pure TiO₂(B) for use as a battery anode. The composite electrodes exhibiting a high initial discharge capacity of 2239.1 mAh g⁻¹ and a discharge capacity of more than 868.7 mAh g⁻¹ could be maintained after 50 cycles at 0.1 C in a voltage range of 1.0–3.0 V at room temperature. The results suggest that TiO₂(B) nanosheets coated with SnO₂ could be suitable for use as a stable anode material for lithium-ion batteries. In addition, the coulombic efficiency of the nanosheets remains at an average of 93.1% for the 3rd–50th cycles.     

On the electrochemical performance of anthracite-based graphite materials as anodes in lithium-ion batteries

The electrochemical performance as potential negative electrode in lithium-ion batteries of graphite materials that were prepared from two Spanish anthracites of different characteristics by heat treatment in the temperature interval 2400-2800 °C are investigated by galvanostatic cycling. The interlayer spacing, d₀₀₂, and crystallite sizes along the c axis, L_c, and the a axis, L_a, calculated from X-ray diffractometry (XRD) as well as the relative intensity of the Raman D-band, I_D/I_t, are used to assess the degree of structural order of the graphite materials. The galvanostatic cycling are carried out in the 2.1-0.003 V potential range at a constant current and C/10 rate during 50 cycles versus Li/Li⁺. Larger reversible lithium storage capacities are obtained from those anthracite-based graphite materials with higher structural order and crystal orientation. Reasonably good linear correlations were attained between the electrode reversible charge and the materials XRD and Raman crystal parameters. The graphite materials prepared show excellent cyclability as well as low irreversible charge; the reversible capacity being up to ∼250 mA h g⁻¹. From this study, the utilization of anthracite-based graphite materials as negative electrode in lithium-ion batteries appears feasible. Nevertheless, additional work should be done to improve the structural order of the graphite materials prepared and therefore, the reversible capacity.     

Hydrothermal synthesis of Co3O4 microspheres as anode material for lithium-ion batteries

Co₃O₄ microspheres were synthesized in mass production by a simple hydrothermal treatment. One micrometer-sized spherical particles with well-crystallization could be obtained by XRD and SEM. Higher specific surface area (93.4 m² g⁻¹) and larger pore volume (78.4 cm³ g⁻¹) by BET measurements offered more interfacial bondings for extra sites of Li⁺ insertion, which resulted in the anomalous large initial irreversible capacity and capacity cycling loss due to SEI film formation. The capacity retention of Co₃O₄ microspheres involved first forming acted as Li-ion anode material is almost above 90% from 12th cycle and it retain lithium storage capacity of 550.2 mAh g⁻¹ after 25 cycles, which show good long-life stability. The electrochemical impedance spectroscopy (EIS) tests before and after cyclic voltammetry measurements and charge-discharge experiments were carried out and the corresponding D_Li values were also calculated. The relationship of the ac impedance spectra and the cycling behaviors was discussed. It is found that the decrease of capacity results from the larger Li⁺ charge-transfer impedance and the lower lithium-diffusion processes on cycling, which is in very good agreement with the electrochemical behaviors of Co₃O₄ electrode.     

Three-dimensional MnO/reduced graphite oxide composite films as anode materials for high performance lithium-ion batteries

MnO/reduced graphite oxide (MnO/RGO) composite films with three dimensionally porous structures have been synthesized by an improved electrostatic spray deposition setup and their microstructure and electrochemical properties have been characterized by X-ray diffraction, scanning electron microscopy, thermal gravimetric, Raman spectrometry and galvanostatic cell cycling. The results show that the structure and electrochemical performance of the electrode film are influenced significantly by the RGO content. The three dimensionally porous structure collapse does not occur in the MnO/RGO thin films for a RGO content lower than 16.58 wt%, the 16.58 wt% reduced graphite oxide content being optimal. Such an improvement in the cycling performance (772 mAh g⁻¹ after 100 cycles at 1 C) and rate capability (425 mAh g⁻¹ at 6 C) might be attributed to the excellent microstructure and electrical conductivity of MnO/reduced graphite oxide composite film electrodes.     

Fabrication of NiO-ZnO/RGO composite as an anode material for lithium-ion batteries

NiO-ZnO/RGO composite was obtained by the annealing of an Ni (OH)₂-Zn (OH)₂/RGO precursor, which has been fabricated by in situ ultrasonic agitation. Moreover, the NiO-ZnO nanoflakes are evenly distributed on the RGO sheets based on the scanning electron microscope (SEM) and transmission electron microscope (TEM) characterization results. When the NiO-ZnO/RGO composite was used as an anode material in lithium-ion batteries (LIBs), the electrodes exhibited a high reversible capacity of 1017 mA h/g at a current density of 100 mA/g after 200 cycles and a specific capacity of 458 mA h/g at 500 mA/g even after 400 cycles. The electrode even reached a capacity of 185 mA h/g at a current density of 2000 mA/g. The excellent electrochemical properties of the NiO-ZnO/RGO composite might be attributable to the NiO-ZnO nanoflakes offering rich electrochemical reaction sites and shortening the diffusion length for lithium ion (Li⁺), as well as the RGO sheets improving the transfer rates of Li⁺ and electron during the charge-discharge process.     

Electrochemical studies of LiB compound as anode material for lithium-ion battery

Electrochemical studies of LiB compound were carried out for its application as anode for lithium-ion battery. The compound exhibited a reversible discharge-charge behavior between 0 and 0.75 V versus Li/Li⁺ with a first discharge capacity of 293 mA h g⁻¹. Discharging to 1.0 V, the first discharge capacity of LiB compound was 660 mA h g⁻¹, but a part of this capacity was irreversible. Impedance spectra were measured at several potentials corresponding to different discharge plateaus. The impedance spectra obtained below and above 0.8 V presented significantly different features. The solid electrolyte interphase layer (SEI) was formed below 0.8 V and assumed a good performance of LiB electrode in this potential range. The SEI was found to deteriorate above 0.8 V, which might be associated with the irreversible discharge capacity.     

Nano-porous Si/C composites for anode material of lithium-ion batteries

Nano-porous silicon composite incorporated with graphite and pyrolyzed carbon was synthesized and investigated as a promising anode material for lithium-ion batteries. The nano-porous Si/graphite composite was prepared via two-step ball-milling followed by etching process. Then carbon was incorporated by using different approaches. The nano-porous Si/graphite/C composite exhibits a reversible capacity of about 700 mAh/g with no capacity loss up to the 120th cycle at a constant current density of 0.2 mA/cm². The superior electrochemical characteristics are attributed to the nanosized pores in Si particles, which suppress the volume effect, and buffering action as well as excellent electronic and ionic conductivity of carbon materials.     

Nanoparticles constructed mesoporous coral-like Mn2O3 as high performance anode for lithium-ion batteries

As well established, the morphology and architecture of electrode materials greatly contribute to the electrochemical properties. Herein, a novel structure of mesoporous coral-like manganese (III) oxide (Mn₂O₃) is synthesized via a facile solvothermal method coupled with the carbonization under air. When fabricated as anode electrode for lithium-ion batteries (LIBs), the as-prepared Mn₂O₃ exhibits good electrochemical properties, showing a high discharge capacity of 1090.4 mAh g^?1 at 0.1 A g^?1, and excellent rate performance of 410.4 mAh g^?1 at 2 A g^?1. Furthermore, it maintains the reversible discharge capacity of 1045 mAh g^?1 at 0.1 A g^?1 after 380 cycles, and 755 mAh g^?1 at 1 A g^?1 after 450 cycles. The durable cycling stability and outstanding rate performance can be attributed to its unique 3D mesoporous structure, which is favorable for increasing active area and shortening Li⁺ diffusion distance.     

A biomass-derived biochar-supported NiS/C anode material for lithium-ion batteries

Nickel sulfides are perfect anode materials for high-capacity and low-cost lithium-ion batteries (LIBs); however, with the shortcoming of polysulfide intermediate dissolution, volume expansion exceeding the limit during cycling also restricts their development. Herein, NiS/C composite materials are successfully anchored on chestnut shell fluff (CSF)-derived biochar by a glucose-auxiliary hydrothermal method along with an annealing treatment. The CSF biochar acts as an effective electron transmission channel for the rapid lithiation/delithiation of NiS and as a fixed sulfur carrier for inhibiting the dissolution of polysulfide. Glucose restrains the accumulation of NiS particles and then transforms into uniform amorphous carbon during annealing, which is more effective in buffering for rapid volume variation. Moreover, the CSF-NiS/C electrode exhibits a remarkable specific capacity of 1522.8 mAh g^-1 (0.1 A g^-1) and distinguished rate performance with 295 mAh g^-1 capacity (3 A g^-1), which are better than those of the pure NiS/C anode material displays. Researchers may be inspired by both of these reasonable design and synthesis strategies that are beneficial for the development of high-performance nickel-based sulfide anode materials for LIBs.     

MnO2 prepared by hydrothermal method and electrochemical performance as anode for lithium-ion battery

Two α-MnO₂ crystals with caddice-clew-like and urchin-like morphologies are prepared by the hydrothermal method, and their structure and electrochemical performance are characterized by scanning electron microscope (SEM), X-ray diffraction (XRD), galvanostatic cell cycling, cyclic voltammetry, and electrochemical impedance spectroscopy (EIS). The morphology of the MnO₂ prepared under acidic condition is urchin-like, while the one prepared under neutral condition is caddice-clew-like. The identical crystalline phase of MnO₂ crystals is essential to evaluate the relationship between electrochemical performances and morphologies for lithium-ion battery application. In this study, urchin-like α-MnO₂ crystals with compact structure have better electrochemical performance due to the higher specific capacity and lower impedance. We find that the relationship between electrochemical performance and morphology is different when MnO₂ material used as electrochemical supercapacitor or as anode of lithium-ion battery. For lithium-ion battery application, urchin-like MnO₂ material has better electrochemical performance.     

Electrochemical properties of SnO2/carbon composite materials as anode material for lithium-ion batteries

SnO₂/carbon composite anode materials were synthesized from SnCl₄·5H₂O and sucrose via a hydrothermal route and a post heat-treatment. The synthesized spherical SnO₂/carbon powders show a cauliflower-like micro-sized structure. High annealing temperature results in partial reduction of SnO₂. Metallic Sn starts to emerge at 500 °C. High Sn content in SnO₂/carbon composite is favorable for the increase of initial coulombic efficiency but not for the cycling stability. The SnO₂/carbon annealed at 500 °C exhibits high specific capacity (∼400 mAh g⁻¹), stable cycling performance and good rate capability. The generation of Li₂O in the first lithiation process can prevent the aggregation of active Sn, while the carbon component can buffer the big volume change caused by lithiation/delithiation of active Sn. Both of them make contribution to the better cycle stability.     

Carbon-coated porous Si/C composite anode materials via two-step etching/coating processes for lithium-ion batteries

A highly stable Si/SiO_x/C composite was synthesized in this study through NaOH etching and carbon-coating approaches for use as an anode material in Li-ion batteries (LIBs). The two-step process not only enhanced the electronic conductivity of the as-synthesized Si/SiO_x/C composite by using the two-step etching/coating processes to enhance the columbic efficiency of Si during cycling processes but also architecturally provided an amorphous Si/SiO_x composite to buffer volume expansion. The Raman spectroscopy and X-ray diffraction results demonstrate that the etching process involves a transition from crystalline Si to amorphous SiO_x. The Fourier transform infrared spectroscopy results further confirm that the vibration mode of Si–O bonding changes from symmetric to asymmetric. The Brunauer–Emmett–Teller analysis reveals that we can control specific surface area and pore-size distribution of NaOH-modified Si by tuning the parameters pertaining to the solid content of Si in NaOH solution. After optimizing the etching and carbon-coating processes, the modified Si/C composite delivered ~780 mAh g⁻¹ for more than 200 cycles at 0.5C, which was better than un-modified one of 315 mAh g⁻¹ after 200 cycles. The results clearly indicate that we could improve cycle stability of Si anode drastically through the NaOH etching process and carbon coating modification. The proposed methodology may provide a potential approach to promoting the synthesis of Si-based anodes for use in the commercial applications of LIBs.