The selective catalytic reduction of nitrogen oxides by methane on noble metal-loaded sulfated zirconia

The selective catalytic reduction of NO_x by methane on noble metal-loaded sulfated zirconia (SZ) catalysts was studied. Ru, Rh, Pd, Ag, Ir, Pt, and Au-loaded sulfated zirconia catalysts were compared with the intact sulfated zirconia. For the NO–CH₄–O₂ reaction, Ru, Rh, Pd, Ir, and Pt showed promotion effect on NO_x reduction, while for the NO₂–CH₄–O₂ reaction, only Rh and Pd showed promotion effect. Over intact and Rh, Pd, Ag, and Au-loaded sulfated zirconia, NO_x conversion in NO₂–CH₄–O₂ reaction was significantly higher than that in NO–CH₄–O₂ reaction, while clear difference was not observed over Ru, Ir, and Pt-loaded sulfated zirconia. Comparison of [NO₂]/([NO]+[NO₂]) in the effluent gases in NO–O₂ and NO₂–O₂ reactions showed that Ru, Ir, and Pt has high activity for NO oxidation under the reaction conditions. These facts suggest that effects of these metals toward NO_x reduction by methane can be categorized into the following three groups: (i) low activity for NO oxidation to NO₂, and high activity for NO₂ reduction to N₂ (Pd, Rh); (ii) high activity for NO oxidation to NO₂, and low activity for NO₂ reduction to N₂ (Ru, Ir, Pt); (iii) low activity for both reactions (Ag, Au). To confirm these suggestions, combination of these metals were investigated on binary or physically-mixed catalysts. The combination of Pd or Rh with Pt or Ru gave high activity for the selective reduction of NO_x by methane.     

Determination of active palladium species in ZSM-5 zeolite for selective reduction of nitric oxide with methane

The active site in ZSM-5 zeolite-supported palladium, which shows the catalytic activity for NO reduction with methane as a reducing agent, has been investigated qualitatively and quantitatively by means of NO chemisorption and NaCl titration, comparing with PdO supported on silica. Palladium species in 0.4 wt.% Pd loaded H-ZSM-5 can adsorb NO equimolarly after calcination at 773 K, and almost all the NO was desorbed at around 673 K, while the palladium species on PdO/SiO₂ hardly adsorbed NO. The palladium species in Pd(0.4)/H-ZSM-5 are ion-exchangeable with Na⁺ in NaCl solution, indicating that they exist in a cationic state of an isolated Pd²⁺. This method for quantitative analysis of the isolated Pd²⁺ cations is named as ‘NaCl titration’. The amount of the isolated Pd²⁺ cationic species increased with increasing palladium content on Pd/H-ZSM-5, and PdO co-existed above 1 wt.%. The amount of the isolated Pd²⁺ cation was unchanged after the reaction of NO₂–CH₄, NO₂–CH₄–O₂, or CH₄–O₂ at 673 K, while the adsorbed amount of NO per the Pd²⁺ as determined by NO-TPD decreased after the NO₂–CH₄–O₂ reaction. It was found by NaCl titration that the catalytic activity of Pd/H-ZSM-5 for NO₂–CH₄–O₂ reaction increased with increasing amount of the isolated Pd²⁺ cationic species up to 0.7 wt.%, while the increase in the amount of PdO led to decrease in selectivity towards NO₂ reduction. The palladium species that are active and selective for NO reduction with CH₄ will be proposed.     

Methanol formation from methane partial oxidation in CH4–O2–NO gaseous phase at atmospheric pressure

The reaction condition for high yield of methanol in a gaseous reaction between methane and oxygen in the presence of NO at atmospheric pressure was explored. Methane partial oxidation without NO (CH₄–O₂) gave only 1% conversion of methane at 966 K. The addition of NO led to a remarkable increase in methane conversion and to high selectivity to C₁-oxygenates. The conversion of methane attained 10% at 808 K in the presence of NO (0.5%) where the selectivities to methanol and formaldehyde were 22.1 and 24.1%, respectively. Nitromethane and carbon oxides were also observed in the product gas. The amount of nitromethane was almost equal and/or near to that of initial NO. The carbon monoxide produced was several times higher than carbon dioxide. Influences of NO concentration, ratio of methane to oxygen, water vapor, and dilution with helium gas on product distribution were measured. Low concentration of NO (0.35–0.55%) was favorable for methanol formation. High selectivity to methanol was obtained at low value of the ratio of methane to oxygen (2.0–3.0) or low concentration of dilution gas (<16%). The NO₂ added promoted methane partial oxidation and selectivity to methanol. Therefore, it was assured that NO_x promoted the formation of CH₃√ and CH₃O√ in the gas phase reaction for CH₄–O₂–NO.     

Effect of Na-addition on catalytic activity of Pt-ZSM-5 for low-temperature NO–H2–O2 reactions

The effect of additives on Pt-ZSM-5 catalysts was studied for the selective NO reduction by H₂ in the presence of excess O₂ (NO–H₂–O₂ reaction) at 100 °C. The reaction of NO in a stream of 0.08% NO, 0.28% H₂, 10% O₂, and He balance yielded N₂ with less than 10% selectivity, which could not be increased by changing Pt loading or H₂ concentration in the gas feed. Co-impregnation of NaHCO₃ and Pt onto ZSM-5 decreased the BET surface area and the Pt dispersion. Nevertheless, the Na-loaded catalyst (Na-Pt-ZSM-5) exhibited the higher NO_x conversion (>90%) and the N₂ selectivity (ca. 50%). Such a high catalytic activity even at high Na loadings (≥10 wt.%) is completely contrast to other Na-added Pt catalyst systems reported so far. Further improvement of N₂ selectivity was attained by the post-impregnation of NaHCO₃ onto Pt-ZSM-5. In situ DRIFT measurements suggested that the addition of Na promotes the adsorption of NO as NO₂⁻-type species, which would play a role of an intermediate to yield N₂. The introduction of Lewis base to the acidic supports including ZSM-5 would be applied to the catalyst design for selective NO–H₂–O₂ reaction at low temperatures.     

NOx storage and reduction characteristics of Pd/MnOx–CeO2 at low temperature

The reaction between hydrogen and NO was studied over 1 wt.% Pd supported on NO_x-sorbing material, MnO_x–CeO₂, at low temperatures. The result of pulse mode reactions suggest that NO_x adsorbed as nitrate and/or nitrite on MnO_x–CeO₂ was reduced by hydrogen, which was spilt-over from Pd catalyst. The NO_x storage and reduction (NSR) cycles were carried out over Pd/MnO_x–CeO₂ in a conventional flow reactor at 150 °C. In a storage step, NO was removed by the oxidative adsorption from a stream of 0.04–0.08% NO, 5–10% O₂, and He balance. This was followed by a reducing step, where a stream of 1% H₂/He was supplied to ensure the conversion of nitrate/nitrite to N₂ and thus restore the adsorbability. It was revealed that the NSR cycle is much more suitable for the H₂–deNO_x process in excess O₂, compared to a conventional steady state reaction mode.     

Role of zeolite structure on reduction of NOx with methane over In- and Pd-based catalysts

Catalytic performances of ZSM-5 based catalysts containing indium or palladium were examined for NO reduction with CH₄ and NO_x chemisorption. The amounts of NO_x chemisorbed on In/H-ZSM-5 were well proportional to the catalytic activities for NO_x reduction. Pd/H-ZSM-5, on the other hand, hardly chemisorbed NO₂, while the catalytic activity for NO₂ reduction with CH₄ is very high. Furthermore, Pd loaded on SiO₂ showed comparably high catalytic activity for NO₂ reduction with CH₄ at 400°C in the absence of oxygen as Pd/H-ZSM-5. CH₄ combustion during NO_x reduction with CH₄ in the presence of oxygen significantly occurred over PdO on SiO₂, while less over Pd/H-ZSM-5. The role of zeolite might be slightly different between In/H-ZSM-5 and Pd/H-ZSM-5: the zeolitic porous structure is needed for In/H-ZSM-5 in order to concentrate NO₂ adspecies on InO⁺ sites, which is important for NO reduction with CH₄ on In/H-ZSM-5 based catalysts, while the ion-exchangeable ability of zeolite is needed for Pd/H-ZSM-5 in order to make Pd²⁺ located in a highly dispersed state, on which NO is strongly chemisorbed.     

Enhanced activity of an In–Fe2O3/H-ZSM-5 catalyst for NO reduction with methane

Selective reduction of NO by CH₄ on an In–Fe₂O₃/H-ZSM-5 catalyst was investigated in the presence of excess oxygen. Compared with In/H-ZSM-5, the In–Fe₂O₃/H-ZSM-5 catalyst with high Fe₂O₃ contents showed higher activity in a wide range of reaction temperatures. It was found that the addition of Fe₂O₃ yielded a promotion effect on CH₄ activation. The influence of water vapor on NO conversion was also investigated. The activity of the In/H-ZSM-5 catalyst has been found to be strongly inhibited by water vapor, while the In–Fe₂O₃/H-ZSM-5 catalyst remained fairly active in the presence of 3.3% steam.     

Analysis of the structural parameters controlling the temperature window of the process of SCR-NOx by low paraffins over metal-exchanged zeolites

Catalytic activity of H- and FeH-ferrierite (FER) zeolites with iron content from 50 to 4000 ppm in NO–NO₂ equilibration and SCR of NO_x by propane was measured, both in NO₂-poor and NO₂-rich streams. The activity of FeH-FER in SCR in NO₂-poor streams depends strongly on the Fe content; this relationship is valid down to traces of iron, while no such correlation was indicated in NO₂-rich streams. This was rationalized by realizing the negligible activity of zeolite protons for NO–NO₂ equilibration. Accordingly the SCR activity of H-FER in NO₂-poor streams necessitates presence of iron traces. In the NO₂–O₂–propane mixtures a process in absence of zeolite catalyst initiating propane oxidation and NO₂→NO conversion, but without N₂ formation, was evidenced at temperatures over 350 °C. It is suggested that such a radical process participate in characteristic narrow temperature window for NO_x reduction by propane.     

CO oxidation on Pd/CeO2–ZrO2 catalysts

The promotive effects of cerium oxide on commercial three-way catalysts (TWCs) for purification of motor exhaust gases have been widely investigated in recent years. This work shows the cooperative effects of CeO₂–Pd on the kinetics of CO oxidation over Pd/CeO₂–ZrO₂. Under reducing-to-moderately oxidizing conditions, a zero-order O₂ pressure dependence is found which can be interpreted on the basis of a mechanism involving a reaction between CO adsorbed on Pd and surface oxygen from the support. The high oxygen-exchange capability of the CeO₂–ZrO₂ support, as determined from temperature-programmed reduction/oxygen uptake measurements is suggested as being responsible for such a catalytic behavior.     

Kinetic studies of CH4 oxidation over Pt–NiO/δ-Al2O3 in a fluidised bed reactor

The oxidation of CH₄ over Pt–NiO/δ-Al₂O₃ has been studied in a fluidised bed reactor as part of a major project on an autothermal (combined oxidation–steam reforming) system for CH₄ conversion. The kinetic data were collected between 773 and 893 K and 101 kPa total pressure using CH₄ and O₂ compositions of 10–35% and 8–30%, respectively. Rate–temperature data were also obtained over alumina-supported monometallic catalysts, Pt and NiO. The bimetallic Pt–NiO system has a lower activation energy (80.8 kJ mol⁻¹) than either Pt (86.45 kJ mol⁻¹) and NiO (103.73 kJ mol⁻¹). The superior performance of the bimetallic catalyst was attributed to chemical synergy. The reaction rate over the Pt–NiO catalyst increased monotonically with CH₄ partial pressure but was inhibited by O₂. At low partial pressures (<30 kPa), H₂O has a detrimental effect on CH₄ conversion, whilst above 30 kPa, the rate increased dramatically with water content.     

An infrared study of the behavior of SO2 and NOx over carbon and carbon-supported catalysts

The heterogeneous reactivity of NO_x and SO₂ with carbon has been investigated with FT-IR spectroscopy. The interaction between NO and SO₂ on carbon surface have been studied in the presence and in the absence of oxygen. Thermal stabilities of surface structures, formed as a result of NO_x and SO₂ chemisorption have been determined by means of FT-IR spectroscopy. During the reaction of NO/O₂ mixture with carbon the surface species, including C–NO₂, C–ONO, C–NCO and anhydride structures are formed. It has been found that SO₂ retards the oxidation reaction of carbon by oxygen. The oxidation of SO₂ on carbon was found to be greatly enhanced by the presence of NO + O₂ mixture. The adsorption capacity of cellulose based carbon, catalytic NO_x decomposition and TPD was studied using a fixed bed flow reactor.     

Interactions NO—CO and O2—NO—CO on CuCo2O4/γ-Al2O3 and on γ-Al2O3- and CuCo2O4/γ-Al2O3-supported Pt, Rh and Pt—Rh catalysts, a transient response study

The interactions NO—CO and O₂—NO—CO have been studied onCuCo₂O₄γ-Al₂O₃ and on γ-Al₂O₃- and CuCo₂O₄γ-Al₂O₃-supported Pt, Rh and Pt—Rh catalysts. The deposition of noble metals (Pt, Rh and Pt—Rh) on CuCo₂O₄γ-Al₂O₃ instead of γ-Al₂O₃ is beneficial in: lowering the temperature at which maximum N₂O is formed and decreasing the maximum N₂O concentration attained; lowering the onset temperature of NO to N₂ reduction, and increasing the N₂ selectivity; preserving the activity towards NO to N₂ reduction on a higher level following the concentration step NO + COO₂+ NO + CO and changing the conditions from stoichiometric to oxidizing (50% excess of oxidants). The reason for this behaviour of the CuCo₂O₄γ-Al₂O₃-based noble metal catalysts is the formation (reversible) of a reduced surface layer on the CuCo₂O₄ supported spinel under the conditions of a stoichiometric NO + CO mixture.     

Reversible sorption–desorption of NOx by mixed oxides under various atmospheres

Characteristics of MnO_y–ZrO₂ and Pt–ZrO₂–Al₂O₃ as reversible sorbents of NO_x were investigated under dynamic changes in atmosphere. These sorbents can be used reversibly with a change of C₃H₈ concentration in the reaction gases. Catalytic reduction of NO occurred in the presence of propane, which was more pronounced on Pt–ZrO₂–Al₂O₃ than on MnO_y-ZrO₂ due to high activity of Pt surface for this reaction on MnO_y in MnO_y–ZrO₂. The sorption was observed as soon as the atmosphere changed from a reducing to an oxidizing one. This implies that a high equilibrium partial pressure of O₂ is necessary for NO uptake since the sorbed NO⁻₃ species becomes stable. The beginning of NO_x desorption atmospheres was somewhat dependent on the amount of stored NO_x. The presence of propane in the gas phase strongly affected the characteristic sorption and desorption properties of MnO_y–ZrO₂ and Pt–ZrO₂–Al₂O₃. The sorption and desorption properties are different for MnO_y–ZrO₂ and Pt–ZrO₂–Al₂O₃, since the noble metal or metal oxide possesses unique activity for the NO reaction with C₃H₈ and the amount of oxygen available for oxidative sorption of NO.     

Catalytic reduction of NOx with H2/CO/CH4 over PdMOR catalysts

Conversion of NO_x with reducing agents H₂, CO and CH₄, with and without O₂, H₂O, and CO₂ were studied with catalysts based on MOR zeolite loaded with palladium and cerium. The catalysts reached high NO_x to N₂ conversion with H₂ and CO (>90% conversion and N₂ selectivity) range under lean conditions. The formation of N₂O is absent in the presence of both H₂ and CO together with oxygen in the feed, which will be the case in lean engine exhaust. PdMOR shows synergic co-operation between H₂ and CO at 450–500 K. The positive effect of cerium is significant in the case of H₂ and CH₄ reducing agent but is less obvious with H₂/CO mixture and under lean conditions. Cerium lowers the reducibility of Pd species in the zeolite micropores. The catalysts showed excellent stability at temperatures up to 673 K in a feed with 2500 ppm CH₄, 500 ppm NO, 5% O₂, 10% H₂O (0–1% H₂), N₂ balance but deactivation is noticed at higher temperatures. Combining results of the present study with those of previous studies it shows that the PdMOR-based catalysts are good catalysts for NO_x reduction with H₂, CO, hydrocarbons, alcohols and aldehydes under lean conditions at temperatures up to 673 K.     

Catalytic behavior of La–Sr–Ce–Fe–O mixed oxidic/perovskitic systems for the NO+CO and NO+CH4+O2 (lean-NOx) reactions

Mixed oxides of the general formula La_0.5Sr_xCe_yFeO_z were prepared by using the nitrate method and characterized by XRD and Mössbauer techniques. The crystal phases detected were perovskites LaFeO₃ and SrFeO_3−x and oxides -Fe₂O₃ and CeO₂ depending on x and y values. The low surface area ceramic materials have been tested for the NO+CO and NO+CH₄+O₂ (“lean-NO_x”) reactions in the temperature range 250–550°C. A noticeable enhancement in NO conversion was achieved by the substitution of La³⁺ cation at A-site with divalent Sr⁺² and tetravalent Ce⁺⁴ cations. Comparison of the activity of the present and other perovskite-type materials has pointed out that the ability of the La_0.5Sr_xCe_yFeO_z materials to reduce NO by CO or by CH₄ under “lean-NO_x” conditions is very satisfying. In particular, for the NO+CO reaction estimation of turnover frequencies (TOFs, s⁻¹) at 300°C (based on NO chemisorption) revealed values comparable to Rh/-Al₂O₃ catalyst. This is an important result considering the current tendency for replacing the very active but expensive Rh and Pt metals. It was found that there is a direct correlation between the percentage of crystal phases containing iron in La_0.5Sr_xCe_yFeO_z solids and their catalytic activity. O₂ TPD (temperature-programmed desorption) and NO TPD studies confirmed that the catalytic activity for both tested reactions is related to the defect positions in the lattice of the catalysts (e.g., oxygen vacancies, cationic defects). Additionally, a remarkable oscillatory behavior during O₂ TPD studies was observed for the La_0.5Sr_0.2Ce_0.3FeO_z and La_0.5Sr_0.5FeO_z solids.     

Synthesis and permeation properties of ion-exchanged ETS-4 tubular membranes

Zeolite membranes, which were composed of ETS-4 with Na cations, were prepared on porous -alumina tubes by hydrothermal synthesis. The membranes, which were formed under optimized conditions, sharply rejected molecules with sizes larger than 0.4 nm. For mixtures of N₂–CO₂, N₂–O₂, N₂–Ar and N₂–CH₄ systems, N₂ permeated faster than the coexisting gas. The N₂/O₂ separation factor for an equimolar mixture was in the range of 2.3–3.5, and the N₂ permeance was in the range of (0.55–2.8)×10⁻⁸ mol m⁻² s⁻¹ Pa⁻¹ at permeation temperatures of 283–333 K. Moisture had some effect on the permeation properties for N₂–O₂ mixtures. The separation factor for the N₂/CH₄ system was larger than that of the N₂/O₂ system. When the membrane was ion exchanged with either Li⁺ or Sr²⁺, the separation factors for N₂/O₂ and N₂/CH₄ systems increased, while the permeances decreased.     

Role of lanthanide elements on the catalytic behavior of supported Pd catalysts in the reduction of NO with methane

In this study, the role of lanthanide elements (Ce, Gd, La, and Yb) on Pd/TiO₂ catalysts in the catalytic reduction of NO with methane was investigated. Steady-state reaction experiments in the presence of oxygen showed that the addition of lanthanide elements increases the oxygen resistance of the catalyst. The post-reaction XPS characterization results revealed that majority of the Pd sites remained in the zero oxidation state in the presence of Ce or Gd. The effect of SO₂ (145 ppm) and H₂O (0–6.6%) in NO–CH₄–O₂ reaction over supported Pd and Gd–Pd catalysts was also investigated. Over the Gd–Pd catalyst with the presence of SO₂, more than 70% NO conversion was obtained for over 6 h while the Pd only catalyst showed a sharper drop in NO conversion. Over the Gd–Pd catalyst, the presence of H₂O showed no effect on NO conversion activity (>99% conversion) during the 18 h the catalyst was kept on stream. Among the lanthanide elements tested, Gd is the most effective, allowing the use of above stoichiometric oxygen concentration.     

Oxidation state of palladium as a factor controlling catalytic activity of Pd/SiO2–Al2O3 in propane combustion

The oxidation state of palladium on SiO₂–Al₂O₃ used for propane combustion was examined by XPS and XRD, and the correlation of the catalytic activity with the oxidation state of palladium was systematically studied. The propane conversion over 5 wt% Pd/SiO₂–Al₂O₃ was measured in the range 1.0≤S≤7.2 (S is defined as [O₂]/5[C₃H₈] based on stoichiometric ratio). The propane conversion strongly depended on the S value and reached the maximum at S=5.5. The oxidation state of palladium also changed with the S value; palladium particles were more oxidized under the reaction mixture of higher S value. On the sample used for the reaction at S=5.5, both of metallic palladium and palladium oxide were found. It is concluded that partially oxidized palladium which has optimum ratio of metallic palladium to palladium oxide shows the highest catalytic activity in propane combustion.     

Selective catalytic reduction of N2O and NOx in a single reactor in the nitric acid industry

The nitric acid industry is a source of both NO_x and N₂O. The simultaneous selective catalytic reduction of both compounds using propane as a reductant has been investigated. A stacked catalyst bed with first a Co-ZSM-5 catalyst and second a Pd/Fe-ZSM-5 catalyst gives >80% conversion of N₂O and NO_x above 300 °C at atmospheric pressure. At 4 bar absolute pressure (bara) the Co-ZSM-5 DeNO_x catalyst shows higher NO_x and propane conversion. This leaves not enough propane for the Pd/Fe-ZSM-5 DeN₂O catalyst, which causes a ‘dip’ in N₂O conversion. Reducing the space velocity (SV) of the first catalyst bed secures high NO_x and N₂O conversions from 300 °C and up at 4 bara.     

NO decomposition and reduction by CH4 over Sr/La2O3

Both NO decomposition and NO reduction by CH₄ over 4%Sr/La₂O₃ in the absence and presence of O₂ were examined between 773 and 973 K, and N₂O decomposition was also studied. The presence of CH₄ greatly increased the conversion of NO to N₂ and this activity was further enhanced by co-fed O₂. For example, at 773 K and 15 Torr NO the specific activities of NO decomposition, reduction by CH₄ in the absence of O₂, and reduction with 1% O₂ in the feed were 8.3·10⁻⁴, 4.6·10⁻³, and 1.3·10⁻² μmol N₂/s m², respectively. This oxygen-enhanced activity for NO reduction is attributed to the formation of methyl (and/or methylene) species on the oxide surface. NO decomposition on this catalyst occurred with an activation energy of 28 kcal/mol and the reaction order at 923 K with respect to NO was 1.1. The rate of N₂ formation by decomposition was inhibited by O₂ in the feed even though the reaction order in NO remained the same. The rate of NO reduction by CH₄ continuously increased with temperature to 973 K with no bend-over in either the absence or the presence of O₂ with equal activation energies of 26 kcal/mol. The addition of O₂ increased the reaction order in CH₄ at 923 K from 0.19 to 0.87, while it decreased the reaction order in NO from 0.73 to 0.55. The reaction order in O₂ was 0.26 up to 0.5% O₂ during which time the CH₄ concentration was not decreased significantly. N₂O decomposition occurs rapidly on this catalyst with a specific activity of 1.6·10⁻⁴ μmol N₂/s m² at 623 K and 1220 ppm N₂O and an activation energy of 24 kcal/mol. The addition of CH₄ inhibits this decomposition reaction. Finally, the use of either CO or H₂ as the reductant (no O₂) produced specific activities at 773 K that were almost 5 times greater than that with CH₄ and gave activation energies of 21–26 kcal/mol, thus demonstrating the potential of using CO/H₂ to reduce NO to N₂ over these REO catalysts.