跨导为220mS/mm的AlGaN/GaN HEMT

介绍了 Al Ga N/ Ga N HEMT器件的研制及室温下器件特性的测试。漏源欧姆接触采用 Ti/ Al/ Pt/ Au,肖特基结金属为 Pt/ Au。器件栅长为 1 μm,获得最大跨导 2 2 0 m S/ mm,最大的漏源饱和电流密度 0 .72 A/ mm。由 S参数测量推出器件的截止频率和最高振荡频率分别为 1 2 GHz和 2 4GHz。     

跨导为325mS/mm的AlGaN/GaN HFET器件

报道了使用国产GaN外延材料(蓝宝石衬底)的AlGaN/GaN HFET器件的制备以及室温下器件的性能.器件栅采用场板结构,其中栅长为0.3μm,场板长为0.37μm,源漏间距为3μm.器件的饱和电流密度为0.572A/mm,最大漏电流密度为0.921A/mm,最大跨导为325mS/mm,由S参数外推出截止频率和最高振荡频率分别为27.9GHz和33.1GHz.     

高跨导AlGaN/GaN HEMT器件

报道了生长在蓝宝石衬底上的AlGaN/GaN HEMT器件的制造工艺以及在室温下器件的性能.器件的栅长为1.0μm,源漏间距为4.0μm.器件的最大电流密度达到1000mA/mm,最大跨导高达198mS/mm,转移特性曲线表现出增益带宽较宽的特点.同时由所测得的S参数推出栅长为1.0μm器件的截止频率(fT)和最高振荡频率(fmax)分别为18.7GHz和19.1GHz.     

太赫兹InP基InAlAs/InGaAs PHEMTs的研制

研制了一种T型栅长为90 nm的InP基In0.52Al0.48As/In0.65Ga0.35As赝配高电子迁移率晶体管(PHEMTs).该器件的总栅宽为2×25 μm,展现了极好的DC直流和RF射频特性,其最大饱和电流密度和最大有效跨导分别为894 mA/mm和1640 mS/mm.采用LRM+ (Line-Reflect-Reflect -Match)校准方法实现系统在1~110 GHz全频段内一次性校准,减小了传统的分段测试多次校准带来的误差, 且测试数据的连续性较好.在国内完成了器件的1~110 GHz全频段在片测试,基于1~110 GHz在片测试的S参数外推获得的截止频率ft和最大振荡频率fmax分别为252 GHz和394 GHz.与传统的测试到40 GHz外推相比,本文外推获得的fmax更加准确.这些结果的获得是由于栅长的缩短,寄生效应的减小以及1~110 GHz全频段在片测试的实现.器件的欧姆接触电阻率减小为0.035 Ω·mm.     

高跨导AlGaN/GaN HFET器件研究

报道了蓝宝石衬底上AlGaN/GaNHFET的制备以及室温下器件的性能。器件栅长为0.8μm,源漏间距为3μm,得到器件的最大漏电流密度为0.7A/mm,最大跨导为242.4mS/mm,截止频率(fT)和最高振荡频率(fmax)分别为45GHz和100GHz。同时器件的脉冲测试结果显示,SiN钝化对大栅宽器件的电流崩塌效应不能彻底消除。     

跨导为325mS/mm的AlGaN/GaN HFET器件

报道了使用国产GaN外延材料（蓝宝石衬底）的AlGaN/GaN HFET器件的制备以及室温下器件的性能. 器件栅采用场板结构,其中栅长为0.3μm,场板长为0.37μm,源漏间距为3μm. 器件的饱和电流密度为0.572A/mm,最大漏电流密度为0.921A/mm,最大跨导为325mS/mm,由S参数外推出截止频率和最高振荡频率分别为27.9GHz和33.1GHz.     

蓝宝石衬底AlGaNöGaN 功率HEM Ts 研制

基于蓝宝石衬底的高微波特性 Al Ga N/Ga N HEMTs功率器件 ,器件采用了新的欧姆接触和新型空气桥方案。测试表明 ,器件电流密度 0 .784A/mm,跨导 1 97m S/mm,关态击穿电压 >80 V,截止态漏电很小 ,栅宽 1 mm的器件的单位截止频率 ( f T)达到 2 0 GHz,最大振荡频率 ( fmax) 2 8GHz,2 GHz脉冲测试下 ,栅宽 0 .75 mm器件 ,功率增益1 1 .8d B,输出功率 3 1 .2 d Bm,功率密度 1 .75 W/mm。     

X波段AlGaN/GaN HEMTs Γ栅场板结构研究

基于SiC衬底成功研制X波段0.25 μm栅长带有r栅场板结构的AlGaN/GaN HEMT,设计场板(field plate)长度为0.4 μm,0.6μm,0.7μm,0.9μm.研究了r栅场板长度及不同漏偏压下对器件直流,小信号特性及大信号的影响.器件直流I-V及转移特性并不依赖场板长度变化,增加场板长度器件击穿电压提高可达108 V,器件截止频率及振荡频率下降,输出功率大幅度提高,结合器件小信号提参结果分析.8 GHz下,总栅宽1 mm,场板长度为0.9 μm的器件,连续波输出功率密度7.11 W/mm,功率附加效率(PAE)35.31%,相应线性增益10.25 dB.     

太赫兹InP基InAlAs/InGaAs PHEMTs的研制（英文）

研制了一种T型栅长为90 nm的InP基In_(0.52)Al_(0.48)As/In_(0.65)Ga_(0.35)As赝配高电子迁移率晶体管(PHEMTs).该器件的总栅宽为2×25μm,展现了极好的DC直流和RF射频特性,其最大饱和电流密度和最大有效跨导分别为894 m A/mm和1 640 m S/mm.采用LRM+(Line-Reflect-Reflect-Match)校准方法实现系统在1~110 GHz全频段内一次性校准,减小了传统的分段测试多次校准带来的误差,且测试数据的连续性较好.在国内完成了器件的1~110 GHz全频段在片测试,基于1~110 GHz在片测试的S参数外推获得的截止频率ft和最大振荡频率f_(max)分别为252 GHz和394 GHz.与传统的测试到40 GHz外推相比,本文外推获得的f_(max)更加准确.这些结果的获得是由于栅长的缩短,寄生效应的减小以及1~110 GHz全频段在片测试的实现.器件的欧姆接触电阻率减小为0.035Ω·mm.     

fT为77GHz的蓝宝石衬底0.25μm栅长AlGaN/GaN高电子迁移率功率器件

在蓝宝石衬底上用MOCVD技术生长的AlGaN/GaN结构上制作出0.25μm栅长的高电子迁移率功率晶体管.0.25μm栅长的单指器件测到峰值跨导为250mS/mm,特征频率为77GHz.功率器件的最大电流密度达到1.07A/mm.8GHz频率下在片测试80×10μm栅宽器件的输出功率为27.04dBm,同时功率附加效率达到26.5%.     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

Teleportation of an arbitrary unknown N-qubit entangled state under the controlling of M controllers

A new quantum protocol to teleport an arbitrary unknown N-qubit entangled state from a sender to a fixed receiver under M controllers(M < N) is proposed. The quantum resources required are M non-maximally entangled Greenberger-Home-Zeilinger (GHZ) state and N-M non-maximally entangled Einstein-Podolsky-Rosen (EPR) pairs. The sender performs N generalized Bell-state measurements on the 2N particles. Controllers take M single-particle measurement along x-axis, and the receiver needs to introduce one auxiliary two-level particle to extract quantum information probabilistically with the fidelity unit if controllers cooperate with it.     

Diode-end-pumped Nd:YVO4/LBO lasers with 4.2W continuous-wave output at 457 nm

A continuous-wave (CW) 457 nm blue laser operating at the power of 4.2 W is demonstrated by using a fiber coupled laser diode module pumped Nd: YVO4 and using LBO as the intra-cavity SHG crystal With the optimization of laser cavity and crystal parameters, the laser operates at a very high efficiency. When the pumping power is about 31 W, the output at 457nm reaches 4.2 W, and the optical to optical conversion efficiency is about 13.5% accordingly. The stability of the out putpower is better than 1.2% for 8 h continuously working.     

A rigorous proof of MIMO channel capacity’s increase with antenna number

It is well known that adding more antennas at the transmitter or at the receiver may offer larger channel capacity in the multiple-input multiple-output（MIMO） communication systems. In this letter, a simple proof is presented for the fact that the channel capacity increases with an increase in the number of receiving antennas. The proof is based on the famous capacity formula of Foschini and Gans with matrix theory.     

Call for Papers

正Wireless Body-area Networks The last decade has witnessed the convergence of three giant worlds:electronics,computer science and telecommunications.The next decade should follow this convergence in most of our activities with the generalization of sensor networks.In particular with the progress in medicine,people live longer and the aging of population will push the development of wireless personal networks