Two-stage heat pump system with vapor-injected scroll compressor using R410A as a refrigerant

Refrigerant vapor-injection technique has been well justified to improve the performance of systems in refrigeration applications. However, it has not received much attention for air conditioning applications, particularly for air conditioning in hot climates and for heat pumping in cold climates. In this study, the performance of an 11 kW R410A heat pump system with a two-stage vapor-injected scroll compressor was experimentally investigated. The vapor-injected scroll compressor was tested with the cycle options of both flash tank and internal heat exchanger configurations. A cooling capacity gain of around 14% with 4% COP improvement at the ambient temperature of 46.1 °C and about 30% heating capacity improvement with 20% COP gain at the ambient temperature of −17.8 °C were found for the vapor-injected R410A heat pump system as compared to the conventional system which has the same compressor displacement volume.     

Effects of liquid refrigerant injection on the performance of a refrigeration system with an accumulator heat exchanger

Liquid refrigerant injection technique can be a very effective method for controlling subcooling and the compressor discharge temperature of a refrigeration system at high ambient temperatures. In this study, the effects of liquid refrigerant injection on the performance of a refrigeration system with an accumulator heat exchanger were investigated by varying the liquid injection rate at the conditions of constant expansion valve opening in the evaporator and constant total flow rate. During the tests, the ambient temperature was maintained at 43 °C. With the increase of the liquid injection rate, the subcooling at the inner heat exchanger outlet increased and the superheat at the accumulator outlet decreased. However, unacceptable results such as the increase of the compressor discharge pressure and decrease of the system performance were also observed depending on the control method applied. To obtain high system performance and reliability, optimum control methods for liquid injection in the accumulator heat exchanger are suggested. The liquid injection technique for the refrigeration system with an accumulator heat exchanger was found to be an effective method for controlling adequate subcooling and the compressor discharge temperature of the refrigeration system at high ambient temperatures.     

Design of experimental bench and internal pressure measurement of scroll compressor with refrigerant injection

Experiments on the inner compression process of scroll compressor with refrigerant injection can reveal the essence of refrigerant injection. The difficulty of the experiment is the design of location of measuring ports, measuring system of dynamic pressure and design of the injection system. Focusing on the dynamic pressure measurement of inner compression process during refrigerant injection, an integrated bench design method for refrigerant injection research in scroll compressor is presented in this paper. The location design of injection ports and measuring ports, frequency spectrum analysis of pressure signal, selection of the sensor type and configuration, and design of the pressure-leading system are expressed, respectively. Finally, a test bench is set up. Based on it, several elementary experiments were carried out. The results show that: this design method solves most problems in the experimental research of scroll compressor with refrigerant injection and works reliably; the refrigerant injection effects the majority of the inner compression process and should not be considered as a transient process; gas injection can increase the system performance greatly and there is an optimal injection pressure for a certain scroll compressor.     

Thermodynamic analysis on the performance of a variable speed scroll compressor with refrigerant injection

A thermodynamic model for a variable speed scroll compressor with refrigerant injection was developed using continuity, energy conservation and real gas equation. The model included energy balance in the low-pressure shell compressor, suction gas heating, motor efficiency, and volumetric efficiency considering gas leakages as a function of compressor frequency. The developed model was verified by comparing the predicted results for the no injection condition with the experimental data. The deviations of the predicted from the measured values were within 10% for approximately 90% of the experimental data. Based on the model, mass flow rate, suction gas heating, cooling capacity and power consumption of the compressor were estimated and analyzed as a function of frequency. The effects of refrigerant injection on the performance of the compressor were also discussed as a function of frequency, injection conditions, and injection geometry.

Résumé

A thermodynamic model for a variable speed scroll compressor with refrigerant injection was developed using continuity, energy conservation and real gas equation. The model included energy balance in the low-pressure shell compressor, suction gas heating, motor efficiency, and volumetric efficiency considering gas leakages as a function of compressor frequency. The developed model was verified by comparing the predicted results for the no injection condition with the experimental data. The deviations of the predicted from the measured values were within 10% for approximately 90% of the experimental data. Based on the model, mass flow rate, suction gas heating, cooling capacity and power consumption of the compressor were estimated and analyzed as a function of frequency. The effects of refrigerant injection on the performance of the compressor were also discussed as a function of frequency, injection conditions, and injection geometry.     

Twin screw oil-free wet compressor for compression–absorption cycle

The performance of a twin screw compressor operating under wet (two-phase) compression conditions in an ammonia–water compression absorption heat pump cycle is investigated both theoretically and experimentally. The paper reports on the influence of the location of liquid intake or, depending what applies, injection angle and mass flow rate of the injected liquid on compressor performance. Labyrinth seals separate the oil-free process side from oil lubricated bearing housing. Labyrinth seals leakage is modelled and its impact on performance is theoretically and experimentally investigated. The need for liquid injection from the discharge side to obtain acceptable performance is discussed based on experimental results.     

Defrost cycle performance for an air-source heat pump with a scroll and a reciprocating compressor

A 10.6 kW nominal cooling capacity air-source heat pump was tested according to ANSI/ASHRAE Standard 116-1983 for the frost acumulation and defrost cycle. These tests required indoor conditions of 21.1°C (70°F) dry-bulb, 15°C (60°F) maximum wet-bulb, with outdoor conditions of 1.7°C (35°F) dry-bulb, 0.5°C (30°F) wet-bulb. The unit was tested with the original scroll compressor and a reciprocating compressor that yielded similar heating performance. Heating capacity for the scroll system peaked at 8.4 kW (2.38 tons), while the reciprocating system heating capacity peaked at 8.5 kW (2.42 tons) during the frosting period. Heating capacities for the two system configurations differed by less than 1% during the frosting period. Power demand for the scroll system peaked at 2.9 kW, and the reciprocating system power demand peaked at 3.1 kW. During the frosting period, the reciprocating system power demand averaged 7% higher than the scroll system power demand. The reciprocating system completed a defrost 5% faster than the scroll system. Scroll system defrost time was 6.8 min while reciprocating system defrost time was 6.5 min. The volume of condensate produced differed by less than 3% with 1680 ml (102.5 in³) and 1640 ml (100 in³) produced by the scroll and reciprocating systems, respectively. Discharge pressures during defrost were within 3% with peak values of 1315 kPa (191 psia) and 1351 kPa (196 psia) for the scroll and reciprocating systems respectively. The reciprocating compressor produced higher levels of discharge superheat, peaking at 53°C (95°F) compared to the scroll system peak discharge superheat of 47°C (85°F). Overall, discharge superheat for the reciprocating system averaged 18% higher than the scroll system. The reciprocating system produced defrost refrigerant flowrates that averaged 3% higher than the scroll system. Refrigerant flowrates for the scroll and reciprocating systems peaked at 3.7 kg min⁻¹ (8.2 lbm min⁻¹) and 4.0 kg min⁻¹) (8.8 lbm min⁻¹) respectively.     

Investigation of R-744 Voorhees transcritical heat pump system

Using economizer in R-744 heat pump cycle is an effective way to improve the heating capacity in cold climates. In this paper, a modification construction of reciprocating compressor with economizer port, a Voorhees compressor was introduced and the heat pump cycle with Voorhees economizer was compared with the traditional screw or scroll economizer cycles. Both the R-744 transcritical heat pumps with and without Voorhees economizer were tested at the same conditions with different air mass flow rates and different evaporating temperatures. The results show that the heating capacity of the heat pump with Voorhees economizer can be two times higher than the transcritical heat pump without economizer at low evaporating temperature conditions. At the same capacity operation conditions, the efficiency of the heat pump with Voorhees economizer is higher at high refrigerant mass flow rate conditions. The optimum discharge pressure of the heat pump with Voorhees economizer is found to be higher than the heat pump without economizer at the same ambient conditions. For mobile heat pump application, CO₂ transcritical heat pump with Voorhees economizer demonstrates better performance comparing to the conventional transcritical CO₂ heat pump without economizer when the evaporating temperature is lower than −20 °C, or when the mobile is idling with low compressor RPM.     

Mathematical modeling of scroll compressors — part II: overall scroll compressor modeling

This paper presents the development of a comprehensive simulation model of a horizontal scroll compressor, which combines a detailed compression process model (Chen Y., Halm N., Groll E., Braun J. Mathematical modelling of scroll compressors — part I: compression process modeling, International Journal of Refrigeration 2002;25(6):731–750) and an overall compressor model. In the overall model, compressor components are analyzed in terms of nine different elements. Steady state energy balance equations are established applying the lumped capacitance method. In combination with the detailed compression process model, these equations were implemented into computer code and solved recursively. In this way, the temperature and pressure of the refrigerant in different compressor chambers, the temperature distributions in the scroll wraps, and the temperatures of the other compressor elements can be obtained. Thereafter, power consumption and efficiency of the compressor can be calculated. Tests were used to verify the overall model on a macroscopic basis. Using the simulation program based on the overall compressor model, a parametric study of the scroll compressor was performed, and the effects of internal leakage and heat transfer losses were investigated and some preliminary results were obtained. These results indicate that the comprehensive scroll compressor model is capable of predicting real compressor behavior and useful to the design and optimization of scroll compressors.     

Comparative study of the impact of the dummy port in a scroll compressor

A dummy port plays an important role in the porting process and the improvement of the performance of a scroll compressor. This paper documents an investigation on the working mechanism of the dummy port in a scroll compressor. To characterize the dummy port effects on the different parts of the scroll compressor, two scroll compressors, one with and the other without a dummy port, are studied comparatively. The flow through the dummy port is examined in the background of an integrated compressor working process. The assembly of the compressor under investigation includes the upper bearing housing, scrolls, check valve, and discharge plenum. The Navier–Stokes equations with a k– turbulence model are solved at the standard operating conditions of a scroll compressor. Refrigerant-22 is used as the working fluid. The thermodynamic and transport properties of the refrigerant gas are modeled by the Martin–Hou equation of state and power laws, respectively. Global flow physics is investigated first to lay a foundation to understand the working mechanisms that control the porting process before averaging techniques are applied. The behavior of the gas pockets in the porting process is characterized in both geometric and dynamic nature. The time-dependent variation of volume, mass, energy, and volume-averaged field quantities inside the gas pockets are studied throughout the porting process. The impact of the dummy port on the compressor performance is defined.     

Loss-efficiency model of single and variable-speed compressors using neural networks

Compressor is the critical component to the performance of a vapor-compression refrigeration system. The loss-efficiency model including the volumetric efficiency and the isentropic efficiency is widely used for representing the compressor performance. A neural network loss-efficiency model is developed to simulate the performance of positive displacement compressors like the reciprocating, screw and scroll compressors. With one more input, frequency, it can be easily extended to the variable speed compressors. The three-layer polynomial perceptron network is developed because the polynomial transfer function is found very effective in training and free of over-learning. The selection of input parameters of neural networks is also found critical to the network prediction accuracy. The proposed neural networks give less than 0.4% standard deviations and ±1.3% maximum deviations against the manufacturer data.     

An investigation of the performance of a scroll compressor under liquid refrigerant injection

In this study, fundamental and practical influence of liquid refrigerant injection on the performance of a refrigerant scroll compressor has been investigated experimentally and theoretically. In the theoretical analysis, a compression model of vapor/liquid mixture is developed by taking account of heat transfer from the cylinder wall to suction, compression and injection refrigerant. An experiment has been done under the condition of keeping the oil temperature constant in order to investigate the fundamental influence of the liquid refrigerant injection on the compressor performance, and the results were compared with the theoretical ones. It was found that the injection basically increases the compression power and decreases the compressor efficiency, though the situation depends on the condition of the heat transfer to the injection refrigerant. And furthermore, the performance of the liquid refrigerant injection compressor under practical operating condition without controlling the oil temperature has been investigated. Under this condition, the compressor showed recovery and slight improvement of performance due to the decrease of the oil and cylinder temperatures by the injection. In addition, influence of the refrigerant injection on the oil viscosity and refrigerant solubility in the oil, which relate mechanical loss and reliability of the compressor, have been discussed.     

Empirical correlation for ejector designCorrélation empirique pour la conception des éjecteurs

In the present study, two empirical correlations from the test results of 15 ejectors are derived for the performance prediction of ejectors using R141b as the working fluid. The ratio of the hypothetical throat area of the entrained flow to the nozzle throat area A_e/A_t, the geometric design parameter of the ejector A₃/A_t, and the pressure ratios P_g/P_e and P_c*/P_e are used to correlate the performance of the ejector. The prediction of the entrainment ratio ω using the correlations is within ±10% error. A method of calculation for the ejector design using the correlations is also developed. R141b is shown in the present study to be a good working fluid for an ejector. The measured ω for the ejectors used in the present study can reach as high as 0.54 at P_g=0.465 MPa (84°C), P_c^*=0.087 MPa (28°C) and P_e=0.040 MPa (8°C). For P_g=0.538 MPa (90°C), P_c^*=0.101 MPa (32°C) and P_e=0.040 MPa (8°C), ω reaches 0.45.

Résumé

Dans cette étude, on a établi deux corrélations empiriques à partir des résultats expérimentaux obtenus utilisant 15 éjecteurs; ces corrélations ont été utilisées ensuite pour prédire la performance d'éjecteurs utilisant le R141b comme fluide frigorigène. Les rapports A_e/A_t (section de passage du fluide entraîné rapporté à la section théorique du col de l'éjecteur), et A₃/A_t (section de sortie de l'éjecteur rapporté à la section théorique du col de l'éjecteur) et les relations entre pressions P_g/P_e et P_c*/P_e sont utilisés pour trouver la corrélation de la performance de l'éjecteur. La prévision du taux d'entraînement à partir des corrélations est précise à la hauteur de ±10%. Les auteurs ont également développé une méthode de calcul permettant de concevoir des éjecteurs à partir des corrélations. On a montré dans cette étude que le R141b s'avère être un fluide actif efficace pour cette utilisation. Le ω mesuré des éjecteurs utilisés dans cette étude peuvent atteindre 0.54 à P_g=0.465 MPa (84°C), P_c^*=0.087 MPa (28°C) et P_e=0.040 MPa (8°C). Pour P_g=0.538 MPa (90°C), P_c^*=0.101 MPa (32°C) et P_e=0.040 MPa (8°C), ω atteint 0.45.     

Effect of inlet humidity condition on the air-side performance of an inclined brazed aluminum evaporator

The effect of air inlet humidity condition on the air-side heat transfer and pressure drop characteristics for an inclined brazed aluminum heat exchanger has been investigated experimentally. For a heat exchanger with a louver angle of 27°, fin pitch of 2.1 mm and flow depth of 27.9 mm, a series of tests are conducted for the air-side Reynolds numbers of 80–400, with variation of inlet humidity condition. The heat transfer data are obtained for wet condition only and the pressure drop data are measured for both dry and wet conditions. The inlet air temperature and relative humidity range are 12 °C and 60–90%, respectively. The inclination angles (θ) from the vertical position are 0, 14, 45, and 67° clockwise (leeward direction). The inclination angles affect moderately the sensible heat transfer coefficient for wet condition, and the pressure drops for both dry and wet conditions increase systematically with the inclination angle. The heat transfer and pressure drop characteristics under wet condition are not influenced substantially by the air inlet humidity for θ 45°. The effect of the louver directions at the inlet and outlet of the inclined heat exchanger on the performance is also addressed.     

A combined-cycle refrigeration system using ejector-cooling cycle as the bottom cycle

A combined-cycle refrigeration system (CCRS) that comprises a conventional refrigeration and air-conditioning system using mechanical compressor (RAC/MC) and an ejector-cooling cycle (EJC) is proposed and studied. The EJC is driven by the waste heat from the RAC/MC and acts as the bottom cycle of the RAC/MC. A system analysis shows that the COP of a CCRS is significantly higher than a single-stage refrigeration system. Improvement in COP can be as high as 18.4% for evaporating temperature of the RAC/MC T_e at −5°C. A prototype of the CCRS was built and tested in the present study. Experimental results show that at T_e=−4.5°C, COP is improved by 14% for a CCRS. For T_e at 5°C, COP can be improved by 24% for a CCRS with higher condensing temperature of the RAC/MC. The present study shows that the CCRS using the ejector-cooling cycle as the bottom cycle of the RAC/MC is viable. Further improvement in COP is possible since the prototype is not designed and operated at an optimal condition.     

Scroll compressors using gas and liquid injection: experimental analysis and modelling

The first part of this paper presents an experimental analysis of different hermetic scroll compressors using different methods of injection: the first one is without injection, the second one uses vapor injection and the third one liquid injection. The analysis reveals the influence of these methods on the compressor behavior. A simplified model of the scroll compressor is then proposed that takes into account not only the different internal processes but also the refrigerant injection. It assumes that the refrigerant mass flow rate is affected by a heating-up due to a uniform wall temperature. This fictitious wall is supposed to gain heat from the electromechanical losses and from the discharged gas and to loose heat to the suction and to the ambient. The compression step is considered isentropic up to the adapted pressure and then at constant volume until the discharge pressure. The model is able to compute variables of first importance like the mass flow rate, the electric power and the discharge temperature, as well as secondary variables as suction heating-up, discharge cooling-down, and ambient losses. The validation based on 45 experimental results shows excellent results.     

Modelling of reciprocating and scroll compressors

This paper presents simple and thermodynamically realistic models of two types of compressors widely used in domestic heat pumps (reciprocating and scroll compressors). These models calculate the mass flow rate of refrigerant and the power consumption from the knowledge of operating conditions and parameters. Some of these parameters may be found in the technical datasheets of compressors whereas others are determined in such a way that the calculated mass flow rate and electrical power match those given in these datasheets.The two models have been tested on five reciprocating compressors and five scroll compressors. This study has been limited to compressors with a maximum electrical power of 10 kW and for the following operating conditions: evaporating temperatures ranging from −20 to 15 °C and condensing temperatures ranging from 15 to 60 °C.The average discrepancies on mass flow rate and power for reciprocating compressors are 1.10 and 1.69% (for different refrigerants: R134a, R404A, R22, R12 and R407C). For scroll compressors, the average discrepancies on mass flow rate and power are 2.42 and 1.04% (for different refrigerants: R134a, R404A, R407C and R22).     

Application of an ejector in autocascade refrigeration cycle for the performance improvement

This paper presented a novel autocascade refrigeration cycle (NARC) with an ejector. In the NARC, the ejector is used to recover some available work to increase the compressor suction pressure. The NARC enables the compressor to operate at lower pressure ratio, which in turn improves the cycle performance. Theoretical computation model based on the constant pressure-mixing model for the ejector is used to perform a thermodynamic cycle analysis for the NARC with the refrigerant mixture of R23/R134a. The effects of some main parameters on cycle performance were investigated. The results show the NARC has an outstanding merit in decreasing the pressure ratio of compressor as well as increasing the COP. For NARC operated at the condenser outlet temperature of 40 °C, the evaporator inlet temperature of −40.3 °C, and the mass fraction of R23 is 0.15, the pressure ratio of the ejector reaches to 1.35, the pressure ratio of compressor is reduced by 25.8% and the COP is improved by 19.1% over the conventional autocascade refrigeration cycle.     

Optimal shape of the multi-passage branching system in a single-phase parallel-flow heat exchanger

A numerical simulation is performed to examine the heat and fluid flow characteristics of the branching system in a single-phase parallel-flow heat exchanger (PFHE) and to obtain its optimal shape. The relative importance of the design parameters [injection angle of the working fluid (Θ), inlet shape and location (Y_c), and height of the protruding flat tube (Y_b)] is determined to decide the optimization sequence. The optimal geometric parameters are obtained as follows: Θ=−21°, Type A, Y_c=0 and Y_b=0. The heat transfer rate of the optimum model compared to that of the reference model is increased by about 55%. The optimal values of the parameters can be applicable to the Reynolds number ranging from 5000 to 20,000.     

Research on air-source heat pump coupled with economized vapor injection scroll compressor and ejector

The performance of the heat pump can be improved further when running under low temperature conditions when an ejector is used in a heat pump system coupled with economized vapor injection (EVI) scroll compressor. In this paper, the design method of the heat pump system with ejector (EVIe) is presented, and the process for designing the heat pump with ejector has been summarized. The optimal location of the vapor injection inlets is at the place where the vapor can inject into the working chambers when they just be closed. The reasonable value for the entrainment ratio u of the ejector is between 0.1 and 0.2. One prototype heat pump was designed under the condition of the evaporation temperature of −20 °C, and an experimental setup was established to test the prototype. The measured results demonstrated that the heating EER of the heat pump system with ejector could reach about 4% higher than that of the system without ejector when the heating capacity remained nearly constant.