Investigation of the aluminum oxide/Si(1 0 0) interface formed by chemical vapor deposition

Thin films of aluminum oxide were deposited using trimethylaluminum and oxygen. The deposition rate was found to decrease with increasing temperature. Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy (XPS) were used to investigate the film/substrate interface. When dry O₂ was used during deposition, the film/substrate interface was free of any silicon dioxide or aluminum silicate phase. On annealing the as-deposited films in Ar, a layer of silicon dioxide film formed at the interface. XPS results indicated that the O/Al ratio in the as-deposited films was higher than that in stoichiometric Al₂O₃. However, the ratio was found to decrease in the annealed samples suggesting that excess oxygen present in the deposited films is responsible for the formation of interfacial silicon dioxide layer. Interfacial phase formation was observed in the as-deposited samples, when small amounts of ozone along with oxygen were used as the oxygen precursor.     

Synthesis of β-Mo(2)C thin films

Thin films of stoichiometric β-Mo(2)C were fabricated using a two-step synthesis process. Dense molybdenum oxide films were first deposited by plasma-enhanced chemical vapor deposition using mixtures of MoF(6), H(2), and O(2). The dependence of operating parameters with respect to deposition rate and quality is reviewed. Oxide films 100-500 nm in thickness were then converted into molybdenum carbide using temperature-programmed reaction using mixtures of H(2) and CH(4). X-ray diffraction confirmed that molybdenum oxide is completely transformed into the β-Mo(2)C phase when heated to 700 °C in mixtures of 20% CH(4) in H(2). The films remained well-adhered to the underlying silicon substrate after carburization. X-ray photoelectron spectroscopy detected no impurities in the films, and Mo was found to exist in a single oxidation state. Microscopy revealed that the as-deposited oxide films were featureless, whereas the carbide films display a complex nanostructure.     

Synthesis and characterization of HfO2 and ZrO2 thin films deposited by plasma assisted reactive pulsed laser deposition at low temperature

A plasma assisted reactive pulsed laser deposition process was demonstrated for low-temperature deposition of thin hafnia (HfO₂) and zirconia (ZrO₂) films from metallic hafnium or zirconium with assistance of an oxygen plasma generated by electron cyclotron resonance microwave discharge. The structure and the interface of the deposited films on silicon were characterized by means of Fourier transform infrared spectroscopy, which reveals the monoclinic phases of HfO₂ and ZrO₂ in the films with no interfacial SiO_x layer between the oxide film and the Si substrate. The optical properties of the deposited films were investigated by measuring the refractive indexes and extinction coefficients with the aid of spectroscopic ellipsometry technique. The films deposited on fused silica plates show excellent transparency from the ultraviolet to near infrared with sharp ultraviolet absorption edges corresponding to direct band gap.     

Substrate temperature effect on the SiC passivation layer synthesized by an RF magnetron sputtering method

This paper describes amorphous silicon carbide (a-SiC) film as an alternative material to silicon nitride (SiN) and silicon oxide (SiO₂) for the passivation layer of solar cells. We deposited the film on p-type silicon (100) wafers and glass substrates by RF magnetron sputtering using a SiC (99%) target. Structural and optical properties of the films were investigated according to the process temperature (room temperature, 300 °C, 400 °C, 500 °C and 600 °C). The structural properties were analyzed by Raman microscopy and XPS (X-ray Photoelectron Spectroscopy). The XPS showed that the content of SiC in the film is increased when the substrate temperature is higher. The optical properties of the films were examined by UV-visible spectroscopy and Ellipsometer. The optical characteristic measurement showed that the lowest refractive index of the film is 2.65. Also, using carrier lifetime measurement, we investigated the performance of SiC as the passivation layer. At the substrate temperature of 600 °C, we obtained a highest carrier lifetime of 7.5 μs.     

Modulation of the structural and optical properties of sputtering-derived HfO2 films by deposition power

High-k gate dielectric HfO₂ thin films have been deposited on Si and quartz substrate by radio frequency magnetron sputtering. The structural and optical properties of HfO₂ thin films related to deposition power are investigated by X-ray diffraction (XRD), fourier transform infrared spectroscopy (FTIR), atomic force microscopy (AFM), ultraviolet–visible spectroscopy (UV–Vis), and spectroscopic ellipsometry (SE). Results confirmed by XRD have shown that the as-deposited HfO₂ thin films are not amorphous state but in monoclinic phase, regardless of deposition power. Analysis from FTIR indicates that an interfacial layer has been formed between the Si substrate and the HfO₂ thin film during deposition. AFM measurements illustrate that the root mean square (RMS) of the as-deposited HfO₂ thin films’ surface demonstrates an apparent reduction with the increase of deposition. Combined with UV–Vis and SE measurements, it can be noted reduction in band gap with an increase in power has been observed. Additionally, increase in refractive index (n) has been confirmed by SE.     

Preparation and photoluminescence of nanocrystalline Si-rich silicon oxide films by PECVD

Nanocrystalline Si-rich silicon oxide films were deposited using plasma enhanced chemical vapor deposition technique with the mixture of silane (SiH₄), nitrous oxide (N₂O) and hydrogen (H₂) as gas source on quartz glass substrate at the substrate temperature of 300 °C. The effect of the ratio N₂O/SiH₄ on the oxidation, microstructures and photoluminescence (PL) of the as-deposited Si-rich silicon oxide films was investigated with FTIR, XRD and HRTEM. The results reveal that with the increasing ratio of N₂O/SiH₄, more amounts of oxygen are incorporated in the as-deposited films and more nanosized silicon particles are embedded in the films, forming nanocrystalline Si-rich silicon oxide films. The quantum confinement effect or the cooperation of quantum confinement and luminescence center results in the nanocrystalline Si-rich silicon oxide films of higher PL intensity.     

Influence of filament-to-substrate distance on the spectroscopic,structural and optical properties of silicon carbide thin films deposited by HWCVD technique

Silicon carbide (SiC) thin films were deposited using hot wire chemical vapor deposition (HWCVD) technique from pure silane and methane gas mixture. The effect of filament distance to the substrate on the structural and optical properties of the films was investigated. Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD), Raman scattering spectroscopy and UV–Vis–NIR spectroscopy were carried out to characterize SiC films. XRD patterns of the films indicated that the film deposited under highest filament-to-substrate distance were amorphous in structure, while the decrease in distance led to formation and subsequent enhancement of crystallinity. The Si–C bond density in the film structure obtained from FTIR data, showed significant increment with transition from amorphous to nano-crystalline structure. However, it remained almost unchanged with further improvement in crystalline volume fraction. From Raman data it was observed that the presence of amorphous silicon phase and sp ² bonded carbon clusters increased with the decrease in distance. This reflected in deterioration of structural order and narrowing the optical band gap of SiC films. It was found that filament-to-substrate distance is a key parameter in HWCVD system which influences on the reactions kinetics as well as structural and optical properties of the deposited films.     

Characteristics of nanocomposite ZrO2/Al2O3 films deposited by plasma-enhanced atomic layer deposition

Nanocomposite ZrO2/Al2O3 (ZAO) films were deposited on Si by plasma-enhanced atomic layer deposition and the film characteristics including interfacial oxide formation, dielectric constant (k), and electrical breakdown strength were investigated without post-annealing process. In both the mixed and nano-laminated ZAO films, the thickness of the interfacial oxide layer (T(IL)) was considerably reduced compared to ZrO2 and Al2O3 films. The T(IL) was 0.8 nm in nano-composite films prepared at a mixing ratio (ZrO2:Al2O3) of 1:1. The breakdown strength and the leakage current level were greatly improved by adding Al2O3 as little as 7.9% compared to that of ZrO2 and were enhanced more with increasing content of Al2O3. The k of ZrO2 and mixed ZAO (Al2O3 7.9%) films were 20.0 and 16.5, respectively. These results indicate that the addition of Al2O3 to ZrO2 greatly improves the electrical properties with less cost of k compared to the addition of SiO2.     

Preparation and investigation of VOx thin films of n- and p-types

In this work we present first results on the synthesis of vanadium oxide semi-transparent conducting thin films of p- and n-types. The films were deposited by thermal evaporation method in vacuum, on: silicon, glass, sapphire, and gold substrates. Temperature of substrate during deposition was set around 250 °C. As deposited films were of a p-type of conductivity. Thermal annealing at 420 °C of as-deposited films in air at atmospheric pressure resulted in a change in the conductivity type.Optical, electrical and thermal properties of the deposited films were studied. The topography of the films was studied using AFM microscope. P-N structures were created using VO_x films on silicon and glass substrates. Electrical measurements had shown a non-linear behaviour of the samples.     

Influence of thermal annealing on microstructural,morphological, optical properties and surface electronic structure of copper oxide thin films

In this study, effect of the post-deposition thermal annealing on copper oxide thin films has been systemically investigated. The copper oxide thin films were chemically deposited on glass substrates by spin-coating. Samples were annealed in air at atmospheric pressure and at different temperatures ranging from 200 to 600°C. The microstructural, morphological, optical properties and surface electronic structure of the thin films have been studied by diagnostic techniques such as X-ray diffraction (XRD), Raman spectroscopy, ultraviolet–visible (UV–VIS) absorption spectroscopy, field emission scanning electron microscopy (FESEM), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS). The thickness of the films was about 520 nm. Crystallinity and grain size was found to improve with annealing temperature. The optical bandgap of the samples was found to be in between 1.93 and 2.08 eV. Cupric oxide (CuO), cuprous oxide (Cu₂O) and copper hydroxide (Cu(OH)₂) phases were observed on the surface of as-deposited and 600 °C annealed thin films and relative concentrations of these three phases were found to depend on annealing temperature. A complete characterization reported herein allowed us to better understand the surface properties of copper oxide thin films which could then be used as active layers in optoelectronic devices such as solar cells and photodetectors.     

Interfacial layer growth of ZrO2 films on silicon

In this work, the interfacial layer growth for both as-deposited and annealed ZrO₂ thin films on silicon is analyzed in detail by the high-resolution cross-sectional transmission electron microscope and spectroscopic ellipsometry. For as-deposited ZrO₂/SiO₂/Si, the thickness of a SiO₂-like layer at the silicon interface was found to depend on the oxygen partial pressure during deposition. At oxygen partial pressure ratio of above 50% the interfacial silicon oxide thickness increased through oxygen diffusion through the ZrO₂ film and silicon consumption at the interface. At oxygen partial pressure ratio in the range 7-50%, the visible growth of interfacial silicon oxide layer was not present. The interfacial layer for ZrO₂/Si with optimal partial pressure (15%) during annealing at 600 °C was found to be the two-layer structure composed of the ZrSi_xO_y overlayer and the SiO_x downlayer. The formation of the interfacial layer is well accounted for diffusion mechanisms involving Si indiffusion and grain-boundary diffusion.     

Mo2C过渡层对金刚石-碳膜场发射均匀性的影响

在经过不同特殊预处理的金属钼衬底上沉积了金刚石 -碳膜 ,分别用X射线衍射谱 (XRD)、拉曼光谱 (Raman)和扫描电子显微镜 (SEM)对样品进行了分析和测试 ,并研究了样品器件的场发射特性。结果发现在金属钼衬底和金刚石 -碳膜之间形成的Mo2 C过渡层与金刚石 -碳膜场发射均匀性有着密切的联系     

Synthesis and optical characterization of amorphous carbon nitride thin films by hot filament assisted RF plasma CVD

Carbon nitride thin films were synthesized by hot filament assisted radio frequency plasma chemical vapour deposition using methane and nitrogen gas mixture on silicon and glass substrates. The films were deposited at different substrate bias and at different substrate temperatures. At higher substrate bias (>−120 V) there was no deposition on the substrate, but complete etching of the deposited layer was observed. X-ray diffraction studies indicated the films were amorphous. The Fourier transform infrared spectra showed that the films produced exhibited high transmittance with the presence of the C-N stretching band at 1260 cm⁻¹. For the films deposited at a lower substrate temperature C=N peaks were also present. Raman spectroscopic study indicated the presence of D and G peaks whose relative height varied with substrate temperature. The transmittance versus wavelength measurement in the UV-VIS-NIR region showed the high transmittance in the NIR region. The optical band gap of the films was calculated to be 2.0 eV and the refractive index varied within 1.6-1.7 for the wavelength range 800-1800 nm.     

Structural and optical properties of yttrium trioxide thin films prepared by RF magnetron sputtering

Yttrium trioxide (Y₂O₃) thin films have been deposited on silicon (111) at different RF powers and the sputtering pressures by RF magnetron sputtering. The influences of the RF power and the sputtering pressures on the structural and optical properties of Y₂O₃ thin films were investigated by X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), atomic force microscope (AFM) and spectroscopic ellipsometer (SE). The results show that chemical composition of as-deposited Y₂O₃ film is apparently close to the stoichiometric ratio and it is crystallized but crystallinity is poor. The monoclinic and cubic fluorite-like structure can coexist in as-deposited Y₂O₃ film. A four-layer-structured optical model consisting of silicon substrate, silicon dioxide (SiO₂) interlayer, Y₂O₃ layer and a surface roughness (SR) layer is built for interpreting preferably the results measured by spectroscopic ellipsometry. With the increase of RF power or decrease of sputtering pressure, the refractive index and optical bandgap of sputtered Y₂O₃ film is increased and the extinction coefficients is decreased.     

大气压非平衡等离子体沉积氧化硅薄膜

本文搭建了一套大气压等离子体薄膜沉积系统,其装置采用喷枪方式,结合运动机构控制喷枪按特定轨迹移动镀膜。四乙氧基硅烷(TEOS)作为硅的先驱体,氮气为先驱体载气和等离子体放电气体,基底温度50℃～300℃,进行了大气压等离子体化学气相沉积氧化硅薄膜的研究。运用红外光谱(FTIR)、光学椭偏仪,扫描电镜(SEM)和纳米压痕仪对沉积的薄膜进行了表征。研究表明,薄膜中富含Si—O—Si键且有少量S—OH键;较高基底温度有利于在硅基底上得到一层平整致密的薄膜;基底温度300℃时薄膜硬度达到4.8GPa,略低于采用PECVD方法沉积的氧化硅薄膜。     

High thermal stability,electrical and optical properties of amorphous IGZO film by coating ultrathin amorphous ITO film as barrier layer

As one kind of well known amorphous transparent conductive oxide films, In–Ga–Zn–O (IGZO) based films were broadly used as electric functional layer in optoelectronic devices. As IGZO film is sensitive to temperature and oxygen, and its electrical and optical properties may probably be deteriorated after subsequent high temperature and air atmosphere. In this work, amorphous indium tin oxide (ITO) layer with two adjustable type of thickness were employed to improve the thermal stability of IGZO films. The doubled ITO/IGZO films were deposited on glass by magnetron sputtering and annealed at high temperatures subsequently to investigate its thermal stability. Accordingly, the crystal structure, optical and electrical properties of ITO/IGZO films were further studied. The XRD results demonstrated that the annealed IGZO films could keep amorphous structure, and the ITO/IGZO films were consisted of uniform small particles which showed comparable dense structure and closely integration with the glass substrate. Furthermore, the sheet resistance results indicated that the increased thickness of top ITO film could suppress oxygen and improve thermal stability of electrical property. Moreover, the transmittance in the visible range was about 85%, and showed a little increase after annealing. The protective ITO layer was found to keep improved thermal stability, good electrical and optical properties at temperatures up to 550 °C.     

Structural and optical properties of yttrium trioxide thin films prepared by RF magnetron sputtering

Yttrium trioxide (Y₂O₃) thin films have been deposited on silicon (111) at different RF powers and the sputtering pressures by RF magnetron sputtering. The influences of the RF power and the sputtering pressures on the structural and optical properties of Y₂O₃ thin films were investigated by X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), atomic force microscope (AFM) and spectroscopic ellipsometer (SE). The results show that chemical composition of as-deposited Y₂O₃ film is apparently close to the stoichiometric ratio and it is crystallized but crystallinity is poor. The monoclinic and cubic fluorite-like structure can coexist in as-deposited Y₂O₃ film. A four-layer-structured optical model consisting of silicon substrate, silicon dioxide (SiO₂) interlayer, Y₂O₃ layer and a surface roughness (SR) layer is built for interpreting preferably the results measured by spectroscopic ellipsometry. With the increase of RF power or decrease of sputtering pressure, the refractive index and optical bandgap of sputtered Y₂O₃ film is increased and the extinction coefficients is decreased.     

Influence of processing variables on the structure and properties of ZnO films

Zinc oxide films of high optical quality have been deposited onto both silica and silicon substrates using reactive sputtering, pulsed laser deposition, and an aqueous solution based technique. Films have been characterized with respect to crystalline phase and phase stability, surface morphology, and optical response by means of X-ray diffraction, Raman spectroscopy, atomic force microscopy, optical transmission and ellipsometry measurements. All films studied were of the wurtzite phase, fine-grained, and exhibited varying degrees of c-axis orientation with respect to the substrate normal depending upon deposition conditions. Films showed some degree of residual tensile stress which was inferred from the E₂ Raman line shift relative to the single-crystal frequency. The wurtzite phase was found to be stable to temperatures near 800 °C, but at higher temperatures, reaction with silica led to evolution of Zn₂SiO₄ at the interface. Variations in Raman line intensities upon post-deposition annealing have been correlated with oxidation of excess zinc in the lattice.     

Evolution of structural and optical properties of nanostructured silicon carbon films deposited by plasma enhanced chemical vapour deposition

Nanostructured silicon carbon films composed of silicon nanocrystallites embedded in hydrogenated amorphous silicon carbon matrix have been deposited by plasma enhanced chemical vapour deposition technique using silane and methane gas mixture highly diluted in hydrogen. The structural and optical properties of the films have been investigated by X-ray diffraction, Raman, Fourier transform infrared, ultra violet-visible-near infrared and photoluminescence spectroscopies while the composition of the films has been obtained from nuclear techniques. The study has demonstrated that the structure of the films evolves from microcrystalline to nanocrystalline phase with the increase in radio frequency (rf) power. Further, it is shown that with increasing the rf power the size of silicon nanocrystallites decreases while the optical gap increases and a blueshift of visible room temperature photoluminescence peak can be observed.     

Interfacial titanium oxide between hydroxyapatite and TiAlFe substrate

The interface between nano-crystalline hydroxyapatite (HA) thin films and a titanium alloy (Ti5Al2.5Fe) has been studied by means of Fourier transform infrared spectrophotometry and X-ray diffraction at grazing incidence. The HA thin films were deposited by radio-frequency magnetron sputtering in low pressure dry argon on substrates kept at low temperature or heated at 550 °C. The effect of film treatment by sputtering and annealing in humid air, as a simple, effective way of restoring the crystallinity and stoichiometry of the HA bulk, was studied in correlation with the development of a titanium oxide layer at the film-substrate interface. An interfacial TiO₂ film grew at the interface during annealing in moist air, while a TiO₂ layer diffused into the HA films when directly sputtered at 550 °C. The formation of an interfacial titanium oxide layer was inhibited by the insertion of a crystalline TiN buffer interlayer between the substrate and the HA film. Separately, the mechanical characteristics of the different HA films were monitored by nanoindentation to find out how they had been affected.