Microstructure and mechanical properties of rapidly quenched L20 and L20+L12 alloys in Ni-Al-Fe and Ni-Al-Co systems

Ductile L2₀-type wires and+L1₂-type duplex wires with high strengths and large elongation in the Ni-Al-Fe and Ni-Al-Co ternary systems have been manufactured directly from the liquid state by an in-rotating-water spinning method. The wire diameter was in the range 80 to 180m and the average grain size was 2 to 4m for the wires and 0.2 to 1.0m for the+ wires. _y, _f and _p of the wires were found to be about 360 to 760 MPa, 560 to 960 MPa, and 0.2 to 5.5%, respectively, for the Ni-Al-Fe system, those of the+ wires were about 395 to 660 MPa, 670 to 1285 MPa, and 3.5 to 17%, respectively, for the Ni-Al-Fe system, and about 260 to 365 MPa, 600 to 870 MPa, and 4.0 to 7.0%, respectively, for the Ni-Al-Co system. Cold-drawing caused a significant increase in _y and _f and the values attained were about 1850 and 2500 MPa, respectively, for Ni-20Al-30Fe and Ni-25Al-30Co wires drawn to about 90% reduction in area. The high strengths, large elongation and good cold-workability of the melt-quenched and+ compound wires have been inferred to be due to the structural change into a low-degree ordered state containing a high density of phase boundaries, suppression of grain-boundary segregation and refinement of grain size.     

Temperature and randomness dependence of the pair-breaking parameter in superconducting aluminum films

Magnetoconductance and excess conductance due to superconducting fluctuations in aluminum films are measured in order to study the temperature dependence of the pair-breaking parameter at temperatures nearT _c . The parameter _M is estimated from the relation =/8k _B T_in, where _in is the inelastic scattering time deduced from the analysis of the magnetoconductance. The parameter _F is determined by fitting theories to data on the excess conductance at zero magnetic field. It is shown that: (1) For films with a wide range of the sheet resistanceR , 12R 200 /, the temperature dependence of _M nearT _c agrees well with the theory of Brenig et al. (2) For clean films withR 100 /, the value of _F analyzed with theories including the correction term to the Maki-Thompson contribution shows almost the same temperature dependence as _M . In a film withR 200 /, however, a discrepancy between _M and _F remains.On leave from College of General Education, Kyushu University, Ropponmatsu, Fukuoka, Japan.     

Wide-band phase-metering frequency transducers with fixed frequency heterodynes

Conclusions It has already been pointed out [3] that the PMFTs with a repeated sequential transformation of frequency in ISSs and restoration of the heterodyne frequency contain a minimum number of transducers (two WBFSs) and provide, only for the condition that <, an adequately small error due to an incomplete suppression of the image frequencies (₁₂) in the WBFSs.Over a wider frequency range (), i.e., at any frequency with the exception of=, the PMFTs operate with the same small errors due to an incomplete suppression of the WBFS image frequencies (₁₂), provided that the ISS contains two WBFSs and an SM, or three WBFSs, and that the reference-signal shaping channel consists of a frequency doubler and k₁=k₂=1.Certain PMFTs which contain an FST at one of the heterodyne outputs [5] (k₂>k₁=1) have even a. wider band. Thus, the PMFTs corresponding to combinations of their component transducers shown in the lines 2, 5, 8, and 11 of Table 1 operate, for any relationship of the frequencies ₁ and k₂, with adequately small errors due to an incomplete supression of the image frequency (₁₂) in the WBFSs.The above error, with the remaining conditions being the same, is minimal (¹²³) in the PMFTs which consist of three WBFSs and have transducer combinations shown in the lines 1 and 3 of Table 1.Bearing in mind that WBFSs can now be made with an image frequency suppression factor of the order of 5·10^–3, the error under consideration of such PMFTs can be of the order of 10^–7 rad or 5·10^–5 degrees, i.e., it can be small as compared with other modern phase-metering devices' error components (due to coupling between channels, presence of higher signal harmonic components, etc).Translated from Izmeritel'naya Tekhnika, No. 1, pp. 21–25, January, 1974.     

Computational thermography: Numerical modeling of the thermal regimes of building structures

We consider numerical methods of simulating thermal regimes of building structures that make it possible to create optimum structures as regards power consumption by using more accurate calculations than those available in existing construction specifications and regulations. Possible means of reducing energy expenditures for formation of an optimum microclimate in living quarters are described.Notation R thermal resistance to heat transfer - _i thermal conductivity - c _i heat capacity - _i moisture content - i number of a layer - S thermal inertia of the material - density of the substance - frequency of harmonic vibrations - t time - Fo Fourier number - thermal diffusivity - t time step - x spatial step - Bi Biot number - h _c coefficient of convective heat transfer - k thermal conductivity - T ambient temperature - T _w wall temperature - Nu Nusselt number - Ra _l Rayleigh number - Gr _l Grashof number - Pr Prandtl number - g free fall acceleration - coefficient of thermal volumetric expansion of air - l characteristic length - coefficient of kinematic viscosity of air - determining temperature - thermal conductivity of the material - q heat flux - s area of the heat transfer surface - perimeter of the heat transfer surface - T free stream velocity - air viscosity Academic Scientific Complex A. V. Luikov Heat and Mass Transfer Institute of the Academy of Sciences of Belarus, Minsk. Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 66 No. 6, pp. 733–738, June, 1994.     

Critical dynamics of a sheared micellar solution

We have investigated the dynamic behavior of a nonionic micellar solution of tetra-ethylene glycoln-decylether (C₁₀ E₄) in water near its critical point in the presence of shear. The non-Newtonian behavior of the viscosity can be represented by * = [ 1 +a(S₄)=]², where* is the viscosity in the absence of shear,S is the shear rate. ₄ is the lifetime of the critical Iluctuations,a is a system-dependent constant, and = 0.02 In addition, we have found that, before attaining a steady state, the sheared mixture undergoing phase separation shows significant shear-dependent rheological effects due to the presence of concentration domains.Paper presented at the Twelfth Symposium on Thermophysical Properties, June 19–24. 1994, Boulder, Colorado, U.S.A.     

Microstructural study of ε-iron-carbonitrides formed by a glow discharge technique

The microstructure and phase transformations occurring in-iron-carbonitrides have been studied by means of X-ray and electron diffraction, electron microscopy and Mössbauer spectrometry. Ordering of the interstitial atoms, N or C, results in a hexagonal unit cell for Fe₃(C, N) with parametersa=a3 andc=c wherea andc are the lattice parameters of the hexagonal close-packed (h c p) iron unit cell. Stacking faults on (0001) planes and partial dislocations with Burgers vector b=1/31 0 ¯1 0 are observed in quenched-Fe₄ (C, N). After quench-aging, the carbonitrides show a structural hardening due to the precipitation of a metastable phase. Slow cooling of-carbonitrides with less than 25 at% interstitials leads to the precipitation of-carbonitride and ferrite in-phase grains which allows the orientation relationships between the-,- and-phases to be defined and a model of the-phase--phase transformation to be proposed.     

The stress dependence of superconducting parameters in pure In and Sn and in α-phase In-Sn alloys

We have measured the length change due to the transition from the super-conducting to the normal state in pure In and Sn and in In-Sn alloys. The measurements were made on single-crystal specimens. The alloys had Sn content ranging from zero to 12 at %. Crystals parallel and perpendicular to the tetragonal axis were grown at each alloy content. We find that the relative length changes l/l are very sensitive to alloy content. From l/l we have calculated the stress derivatives H _c/ and T _c / and we find that T _c / changes from +59 to –92 mK/bar for stress along the tetragonal axis, and from –9 to 46 mK/kbar for stress perpendicular to the tetragonal axis. We suggest that these large changes are due to Fermi surface topology changes upon increasing the Sn content in In.     

Transient thermal stress analysis of multilayered hollow cylinder

Summary This paper deals with the transient response of one-dimensional axisymmetric quasistatic coupled thermoelastic problems. Laplace transform and finite difference methods are used to analyze the problems. Using the Laplace transform with respect to time, the general solutions of the governing equations are obtained in the transform domain. The solution is obtained by using the matrix similarity transformation and inverse Laplace transform. We obtain solutions for the temperature and thermal stress distribution in a transient state. Moreover, the computational procedures established in this article can solve the generalized thermoelasticity problem for a multilayered hollow cylinder with orthotropic material properties.Nomenclature Lame's constant - density - C _v specific heat - k _r ,k radial and circumferential thermal conductivity - _r , linear radial and circumferential thermal expansion coefficient - E _r ,E radial and circumferential Young's modulus - v _r Poisson's ratio - ₀ reference temperature - ,T dimensional and nondimensional temperature - r ^*,r dimensional and nondimensional radial coordinate - ,t dimensional and nondimensional time - _r ^* , _r dimensional and nondimensional radial stress - ^* , dimensional and nondimensional circumferential stress - U, u dimensional and nondimensional radial component of displacement     

Supercarrier Effective Mass Isotope Effect by Interband Scattering

Supercarrier effective mass isotope effect (exponent ) is investigated using a two-band model with interband pair scattering. The corresponding repulsive interaction incorporates besides the dominating electronic (Coulomb) part an electron-phonon contribution inversely proportional to the ionic mass factor. Calculations illustrating the behaviour of T _c , its isotope exponent , and with doping in La _2–x Sr _x CuO ₄ type underdoped system reflect the observed tendencies. ² Both and diminish with doping, the sign of is opposite to . A typical estimation gives || 0.2.     

Irreversibilites in science and technology networks: An empirical and analytical approach

The theory of autopoiesis, i.e., self-referentiality in the operation of the system, provides us with a production rule for change in the structure of the network. Using information theory, a model system is developed to study the relative likelihood of dynamic transitions: various senses of irreversibility (emergence, and path dependency) are disinguished. A test for path dependency is applied to two sets of empirical data which supposedly reflect historical discontinuities: the budget of theFraunhofer Gesellschaft, and the citation network among AIDS research related journals. The model for the interaction between self-referential developments and goal-referential boundary conditions is further specified, using the example of technological trajectories and selection environments.     

Hall-Effect in LuNi2B2C and YNi2B2C Borocarbides in Normal and Superconducting Mixed States

It was shown that the Hall resistivity _xy for LuNi ₂ B ₂ C and YNi ₂ B ₂ C is negative in the normal and mixed states and has no sign reversal below T _c . In the mixed state the scaling relation _{xy xx} (_xx is the longitudinal resistivity) was found for both compounds with 2.0. In the normal state a distinct nonlinearity in the _xy(H) dependence, accompanied by a large magnetoresistance, was found below 40 K only for LuNi ₂ B ₂ C. The difference in the behaviour of Lu- and Y-based borocarbides seems to be connected with the difference in the Fermi surfaces of these compounds.     

Piezoelectric and mechanical properties of ceria-doped lead zirconate titanate ceramics

Phases, microstructures and properties of lead-zirconate-titanate (PZT) ceramics with the compositions Pb(Zr_0.535– Ce Ti_0.465) O₃ where =0.0, 0.001, 0.01, 0.02 and 0.05 were studied. Rhombohedral and tetragonal phases were present at =0.0. The amount of the rhombohedral phase increased with increasing , and only the tetragonal phase was present for >0.001. Thec/a ratio of the tetragonal phase also increases with increasing . Particles of CeO₂ were found to be present in compositions with >0.01, indicating that the solubility of CeO₂ is less than 1a/o on the metals basis. The piezoelectric and electromechanical constants achieved maximum values for =0.001. The hardness increased monotonically with increasing . The modulus of rupture and the fracture toughness, however, went through a minimum and both stayed lower than their values for =0.     

Thermal expansion of an SiC particle-reinforced aluminum composite

Using a push-rod dilatometer, we measured between 76 and 390 K the thermal expansion of a particle-reinforced-composite wrought plate obtained by powdermetallurgy methods. The particles, 30% by volume, consisted of monocrystals of -SiC with sizes near 10 m. The matrix consisted of a 6061 aluminum alloy with original particle sizes near 20 m. We found the perpendicular thermal expansivity, ₃, higher by 26% than the in-plane thermal expansivity, ₁-₂. These values differ from a rule-of-mixture prediction by –3 and –23%, respectively. All three _i, components lie outside the Rosen-Hashin bounds. Levin's isotropic model agrees within 10% with the ₁-₂-₃ average. Both the anisotropy and the bounds violation result from microstructural nonhomogeneity arising from processing. Rosen and Hashin's transverse-isotropicsymmetry relationships account approximately for these effects by introducing the anisotropic elastic constants. Using neutron diffraction, we determined that the SiC particles are textureless.Paper presented at the Tenth International Thermal Expansion Symposium, June 6–7, 1989, Boulder, Colorado, U.S.A.     

Methodology for the determination of the interfacial properties of brittle matrix composites

The interfacial properties of a glass-ceramic matrix composite (SiC/CAS) were determined from single-fibre push-out tests using the interfacial test system. The coefficient of friction, , the residual clamping stress, _c, and fibre axial residual stress, _z , were extracted by fitting the experimental stress versus fibre-end displacement curves using the models of Hsueh, and Kerans and Parthasarathy. Using Hsueh's model, the intrinsic interfacial frictional stress (=_c) was found to be 11.1±3.2 MPa, whereas by using Kerans-Parthasarathy's model it was found to be 8.2±1.5 MPa. Comparisons between these models are included, together with a discussion of data analysis techniques.Nomenclature _z Axial fibre residual stress (Pa) - ^* Effective clamping stress (Pa) - _c Residual clamping stress (Pa) - _p Poisson's effect-induced clamping stress (Pa) - _d ⁰ Debond stress in the absence of residual stresses (Pa) - _d Experimental debond stress (Pa) - Compressive applied stress (Pa) - Interfacial shear stress (Pa) - u Fibre-end displacement (m) - h Debond length (m) - r Fibre radius (m) - E _f Fibre Young's modulus (Pa) - E _m Matrix Young's modulus (Pa) - v _f Fibre Poisson's ratio (dimensionless) - v _m Matrix Poisson's ratio (dimensionless) - f Fibre volume fraction (dimensionless) - k Parameter (dimensionless) - D Parameter (dimensionless) - Interfacial coefficient of friction (dimensionless) - G _i Interface toughness (J m^–2) - C _m Load-train compliance (m N^–1)     

Theory of RF SQUIDs Operating in the Presence of Large Thermal Fluctuations

A comprehensive analytical theory is presented for non-hysteretic RF SQUIDs operating in the adiabatic mode in the presence of large thermal fluctuations. When 1 ( = 2LI_c/₀ is the hysteresis parameter, L is the SQUID inductance, I_c is the critical current of the Josephson junction, and ₀ is the flux quantum) the theory is applicable also for RF SQUIDs operating in the non-adiabatic mode. In contrast to previous theories in which the noise is treated perturbatively and which therefore are applicable only if the product 1 ( = 2k_BT/ ₀ I_c is the noise parameter, k_B is the Boltzmann constant, and T is the absolute temperature)—the case of small thermal fluctuations—the present theory is valid for around unity or higher. In the limit 0 the theory reproduces the results of small thermal fluctuations theories. It has been found that in the presence of large thermal fluctuations the screening current in the SQUID inductance is suppressed by a factor that increases with increasing . Taking into account this new basic fact, all SQUID characteristics (output signal, transfer function, noise spectral density and energy sensitivity) have been recalculated and a good agreement with experimental data has been obtained. It has been also found that RF SQUIDs can be operated with substantially higher values of the inductance and of the noise parameter than DC SQUIDs. These two aspects, which are of particular importance at liquid nitrogen temperature, make high T_c RF SQUIDs very attractive.     

Thermal boundary resistance in superfluid4He nearT λ

New measurements of the boundary resistivity in superfluid⁴He (2ppb³He) nearT are reported as a function of ¦¦ ( =T/T (Q) — 1) and of heat flux Q in a cell with parallel polished copper surfaces. Here we call T(Q) the temperature where the superfluid state abruptly disappears. In this design, the sidewall gaps between the copper pieces and the stainless steel spacer were eliminated. In contrast to several previous experiments but in agreement with those of Li and Lip a, no largeQ-dependent boundary resistivity anomaly was detected. However, as ¦¦ 0 the small weakly divergent resistivity was observed and its dependence onQ over the experimental range 1 <Q < 80 W/cm² was found to be very small. These new results are compared with previous experiments and predictions. An explanation of the previously observed anomalous transport phenomena is presented in terms of a heat flow through the sidewall gaps in these cells, and its limitation by a critical flow value _c. This phenomenological model can be fit satisfactorily to the observations. In the appendix we calculate _c from mutual friction.     

Flow visualization glass-ceramic: Preliminary experimental and modelling results

A glass-ceramic material was developed to act as a flow visualization material. Preliminary experiments indicate that aperiodic, thermally induced, convective flows can be sustained at normal processing conditions. These flows and the stress and temperature gradients induced are most likely responsible for the anomalous behaviour seen in these materials and the difficulties encountered in their development and in their production on industrial and experimental scales. A simple model describing the dynamics of variable-viscosity fluids was developed and was shown to be in qualitative agreement with more sophisticated models as well as with experimental results. The model was shown to simulate the dependence of the critical Rayleigh number for the onset of convection on the viscous properties of the fluid at low T, and also to simulate quenching behaviour when the temperature differences were high.Nomenclature C _p Heat capacity - D, E, F Expansion coefficients - H Height of the roll cell - Pr Prandtl number - R _a Rayleigh number - R _c Critical Rayleigh number for the onset of convection in a constant-viscosity fluid - S Dimensionless stream function - T Temperature - T _m Mean temperature - T ₀ Bottom surface temperature - T _r Reference temperature - a Aspect ratio of cell - g Acceleration due to gravity - k Thermal conductivity - k ₁ Function related to ²v/T ² - k ₂ Function related to ⁴v/T ⁴ - r Rayleigh number ratioR _a/R _c - t Time - w Dimensionless vertical coordinate - w _m Mean cell height - x Horizontal coordinate - y Dimensionless horizontal coordinate - z Vertical coordinate - , Constants - _t Thermal expansion coefficient - Constant in viscosity function - T Temperature difference between top and bottom surfaces - _i Viscosity coefficients - Kinematic viscosity - _m Mean kinematic viscosity - Dimensionless kinematic viscosity - Thermal diffusivity - Non-linear temperature function - Dimensionless non-linear temperature function - _o - Stream function - Dimensionless time - Eigenvalues     

Measurements of Critical Current of Superfluid 4He through An Array of Submicron Apertures very near Tλ

Far from the lambda transition the critical flow of superfluid ⁴ He through a small orifice is determined by thermal nucleation of quantized vortices. Between 300 mK and 2 K linearly decreasing critical flow velocity has been observed earlier. As the temperature approaches T the size of the vortex core increases and becomes comparable to that of the orifice. We report here measurements of the critical mass current in this temperature range. An array of 24 3×0.17 m holes in parallel with a macroscopic parallel path and flexible-diaphragm Helmholtz resonator have been used. The temperature range explored was from 80 mK to 20 K below T. Preliminary analysis of the data shows that for a reduced temperature t=(T–T)/T1·10 ^–4 the critical current scales approximately as t ^1.25 . Closer to T the critical phase difference across the array becomes comparable to 2 and the results have to be analyzed in terms of Josephson effect. The superfluid density has been measured at the same time as the critical current.     

An investigation of the ordered DO19 phase formation in the Ti-Al system

For the Ti-rich, Ti-AI system, the- and- ₂ phase boundaries have been obtained through differential thermal analysis for alloy compositions ranging from 10.2 to 25.2 at% Al (6 to 16 wt% Al). It has been shown that in the above mentioned composition range, a metastable disordered-phase can be quenched in. This metastable then transforms to the ordered ₂(DO)₁₉ phase upon heating and/or isothermal ageing. It has also been observed that the kinetics of this ordering phenomenon is composition dependent.     

Microstructural evolution in rapidly solidified Al-Cu-Si ternary alloys

Several Al-Cu-Si alloys were melt spun to produce stable, fine scale microstructures suitable for superplastic deformation and consolidation. Scanning electron microscopy of the ribbon cross-sections reveal two distinct alternating microstructural morphologies, suggesting transitions in solidification behavior. One structure consists of intimately interlocked -Al and (Al₂Cu) phases with dispersed spheroids of (Si). The other structure consists of equiaxed or cellular-dendritic -Al with interdendritic and (Si). The latter was found in the middle portion of the ribbon cross-section when cast at a low speed, and throughout the ribbon cross-section when cast at high speed. The dendritic structure appears to result from independent nucleation events in the undercooled liquid ahead of the solid-liquid interface. The solidification mechanism for the interlocked structure appears to involve multiple nucleation of the phase followed by its cooperative growth with the -Al phase. This cooperative growth is unlike that which forms a lamellar structure, as it results in a branched, randomly oriented network. We postulate that the (Si) phase is the first phase to form from the undercooled liquid, and it is uniformly dispersed throughout the undercooled melt. The (Si) spheroids provide nucleation sites for the phase because of its observed association with the phase. The -Al grain size varies from 1 m near the wheel side surface of the ribbon to 8 m with sub-grains near the free surface. The size of the and (Si) phases is on the order of a m and less. The microstructural size scale appears to be small enough for this material to exhibit superplastic behavior when deformed.