Ag,Al,Ga对Sn-9Zn无铅钎料润湿性能的影响

采用润湿平衡法测试了Sn-9Zn-X(X为Ag,Al,Ga)无铅钎料分别配合ZnCl2-NH4Cl钎剂和免清洗助焊剂,在空气和氮气保护的两种条件下的润湿性能,分析研究了合金元素Ag,Al,Ga的添加量对Sn-9Zn-X无铅钎料润湿性的影响规律.结果表明,合金元素Ag,Al,Ga在Sn-9Zn中的最佳添加量(质量分数)分别为0.3%,0.005%～0.02%,0.5%.采用氮气保护可以显著改善Sn-9Zn-X无铅钎料的润湿性,而Sn-9Zn-X无铅钎料配合ZnCl2-NH4Cl钎剂时具有较好的润湿性,甚至优于Sn-3.5Ag-0.5Cu在相同条件下的润湿性.这一研究结果表明,通过研发适合于Sn-Zn系无铅钎料的高性能助焊剂,从而改善Sn-Zn系钎料的润湿性能是完全可行的.     

Sn-Zn-Cu无铅钎料的组织、润湿性和力学性能

研究了(Sn-9Zn)-xCu无铅钎料的微观组织、润湿性能和力学性能.Cu的加入使得Sn-9Zn钎料中针状富Zn相逐渐转变为Cu-Zn化合物,当Cu含量为8%时,Cu6Sn5相生成.Sn-Zn-Cu合金熔点随着Cu含量增加而升高,同时润湿性随Cu的加入得到显著改善.使用中性活性松香钎剂,钎料与Cu箔钎焊时的润湿角显著减小.Sn-9Zn的润湿角为120°,而(Sn-9Zn)-10Cu的润湿角为54°.这是由于Cu的加入降低了Zn的活性,减少了Zn在钎料表面氧化,降低了液态钎料表面张力,使得钎料能获得较好的润湿性.合金在2%Cu时获得较高的强度,随着Cu含量的增加,Cu-Zn化合物相对增多,抗拉强度有所下降;而合金的塑性随着Cu的加入迅速下降.     

ZL102合金用低温软钎料的研究

Sn-9Zn共晶钎料可以用于钎焊钎焊性极差的铸造铝合金ZL102，在Sn-9Zn钎料的基础上添加In元素，以提高钎料对ZL102合金的润湿。本文对Sn-9Zn和Sn-9Zn-5In两种软钎料对ZL102合金润型，界面结合等方面进行研究，分析实验结果可知，Sn-9Zn-5In钎料的性能优于Sn-9Zn共晶钎料。     

Sn-0.3Ag-0.7Cu-xSb无铅钎料润湿性

研究了微量Sb元素对Sn-0.3Ag-0.7Cu无铅钎料润湿性的影响,采用润湿平衡法探讨了Sn-0.3Ag-0.7Cu-xSb钎料在不同氛围和不同钎剂条件下的润湿性能.结果表明,微量的Sb元素可以显著提高Sn-0.3Ag-0.7Cu无铅钎料润湿性.在氮气氛围条件下,Sn-0.3Ag-0.7Cu-xSb钎料的润湿性得到显著改善,主要基于氮气氛围减小熔融钎料的氧化.辅助不同的钎剂,钎料的润湿性差异较大,选择合适的钎剂可以明显提高Sn-0.3Ag-0.7Cu-xSb钎料的润湿性.     

Sn-9Zn-xPr钎料钎焊性能及显微组织

研究了稀土元素Pr的添加量对Sn-9Zn无铅钎料的润湿性能、显微组织和焊点力学性能的影响.结果表明,镨的加入不仅改善了钎料的润湿性能和抗氧化性能,而且细化了钎料基体中的富锌相,使得界面组织更为稳定,有利于焊点可靠性的改善;Sn-9Zn无铅钎料中镨的添加量为质量分数0.08%时,钎料的润湿性能最佳,综合性能最好;当镨的添...     

Sn-9Zn-xCe钎料显微组织及钎焊性能的分析

研究了添加稀土元素Ce对Sn-9Zn无铅钎料的润湿铺展性能、显微组织和焊点力学性能的影响.结果表明,Ce元素的加入改善了钎料的润湿铺展性能,质量分数为0.08%时,钎料的铺展面积达到最大,润湿性能最佳.随着Ce元素的加入,钎料的基体组织得到细化,富Zn相逐渐减少,当元素Ce的添加量大于0.08%时,钎料的显微组织中出现块状稀土元素Ce和Sn的金属间化合物.无铅钎料Sn-9Zn中稀土元素Ce的添加量为0.08%时,钎料焊点的力学性能最佳.     

稀土元素Nd对Sn-9Zn无铅钎料性能的影响

研究了添加稀土元素Nd对Sn-9Zn无铅钎料的润湿性能、显微组织和焊点力学性能的影响.结果表明,Nd元素的加入改善了钎料的润湿性能,质量分数为0.06%时,钎料的润湿力最大,润湿时间最短,润湿性能达到最佳.随着Nd元素的加入,钎料的基体组织得到细化,富锌相逐渐减少,当元素Nd的添加量大于0.06%时,钎料的显微组织中出现小块状稀土元素Nd和Sn的金属间化合物.无铅钎料Sn-9Zn中稀土元素Nd的添加量为0.06%时,剪切力和拉伸力达到最大,分别提高了19.6%和26.6%,力学性能最佳.     

微量RE对Sn-2．5Ag-0．7Cu钎料合金润湿性的影响

采用润湿平衡法,研究了水洗钎剂条件下Sn-2.5Ag-0.7Cu-xRE无铅钎料合金在1206片式元器件和Cu焊盘上的润湿性.结果表明,添加质量分数为0.1%的RE的Sn-2.5Ag-0.7Cu钎料合金在1206表面贴装元器件和Cu焊盘上有最大的润湿力和铺展面积及最小的润湿角,其润湿性最好,润湿力优于Sn-3.8Ag-0.7Cu钎料合金,满足微电子行业对润湿性能的要求.     

Sn-9Zn-xAl无铅钎料润湿性能

采用润湿平衡法测试了不同温度下Sn-9Zn-xAl无铅钎料在空气和氮气两种气氛下的润湿性能,研究探索了合金元素Al的添加量、气氛和温度对Sn-9Zn-xAl无铅钎料润湿性能的影响规律.结果表明,添加Al元素以后,Sn-Zn-xAl无铅钎料的润湿性得到明显改善,在使用ZnCl2-NH4Cl助焊剂时,Al的最佳添加量为0.02%(质量分数),在使用免清洗助焊剂时,Al的最佳添加量为0.005%(质量分数);采用氮气保护时,Cu基板表面张力提高,钎料的氧化减少、表面张力降低,明显改善了钎料在Cu基板上的润湿性能;在215～245℃时,温度升高使钎料的表面张力减小,提高了钎料的润湿性能.     

Ag、RE对Sn-Ag-Cu-RE无铅钎料润湿性的影响

采用商用水洗钎剂，以铺展面积和润湿角来表征钎料的润湿性能，研究了Ag、RE对Sn-Ag-Cu-RE系无铅钎料润湿性的影响。结果表明，添加微量RE有助于提高其润湿性。在无铅钎料中Sn-2．5Ag-0．7Cu-0．1RE钎料具有良好的润湿特性，其在铜板上润湿性接近Sn-Pb钎料的水平。     

Effects of Post-weld Heat Treatment on Microstructure,Mechanical Properties and the Role of Weld Reinforcement in 2219 Aluminum Alloy TIG-Welded Joints

In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone.     

The First Phase of the SRIF Industrialized Base in ＂West Area＂ Has Been Put into Operation

After nearly two years＇ tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry （SRIF）, located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation.     

Thermodynamics Study on the Decomposition of Chromite with KOH

Institute of Process Engineering, Chinese Academy of Sciences, China, has proposed a method for oxidative leaching of chromite with potassium hydroxide. Understanding the mechanism of chromite decomposition, especially in the potassium hydroxide fusion, is important for the optimization of the operating parameters of the oxidative leaching process. A traditional thermodynamic method is proposed and the thermal decomposition and the reaction decomposition during the oxidative leaching of chromite with KOH and oxygen is discussed, which suggests that chromite is mainly destroyed by reactions with KOH and oxygen. Meanwhile, equilibrium of the main reactions of the above process was calculated at different temperatures and oxygen partial pressures. The stable zones of productions, namely, K2CrO4 and Fe2O3, increase with the decrease of temperature, which indicates that higher temperature is not beneficial to thermodynamic reactions. In addition, a comparison of the general alkali methods is carried out, and it is concluded that the KOH leaching process is thermodynamically superior to the conventional chromate production process.     

Influence of Heat Treatment on Damping Behaviour of the Magnesium Wrought Alloy AZ61

The effect of isochronal heat treatments for 1h on variation of damping, hardness and microstructural change of the magnesium wrought alloy AZ61 was investigated. Damping and hardness behaviour could be attributed to the evolution of precipitation process. The influence of precipitation on damping behaviour was explained in the framework of the dislocation string model of Granato and Lücke.     

Effect of Rare Earth Doping on Impedance,Modulus and Conductivity Properties of Multiferroic Composites:0.5(BiLa_xFe_(1-x)O_3)–0.5(PbTiO_3)

The Lanthanum-doped bismuth ferrite–lead titanate compositions of 0.5(Bi LaxFe1-xO3)–0.5(Pb Ti O3)(x = 0.05,0.10,0.15,0.20)(BLxF1-x-PT) were prepared by mixed oxide method.Structural characterization was performed by X-ray diffraction and shows a tetragonal structure at room temperature.The lattice parameter c/a ratio decreases with increasing of La(x = 0.05–0.20) concentration of the composites.The effect of charge carrier/ion hopping mechanism,conductivity,relaxation process and impedance parameters was studied using an impedance analyzer in a wide frequency range(102–106Hz) at different temperatures.The nature of Nyquist plot confirms the presence of bulk effects only,and non-Debye type of relaxation processes occurs in the composites.The electrical modulus exhibits an important role of the hopping mechanism in the electrical transport process of the materials.The ac conductivity and dc conductivity of the materials were studied,and the activation energy found to be 0.81,0.77,0.76 and 0.74 e V for all compositions of x = 0.05–0.20 at different temperatures(200–300 °C).     

Quantitative Analysis of the Crystallographic Orientation Relationship Between the Martensite and Austenite in Quenching–Partitioning–Tempering Steels

The orientation relationships(ORs)between the martensite and the retained austenite in low-and medium-carbon steels after quenching–partitioning–tempering process were studied in this work.The ORs in the studied steels are identified by selected-area electron diffraction(SAED)as either K–S or N–W ORs.Meanwhile,the ORs were also studied based on numerical fitting of electron backscatter diffraction data method suggested by Miyamoto.The simulated K–S and N–W ORs in the low-index directions generally do not well coincide with the experimental pole figure,which may be attributed to both the orientation spread from the ideal variant orientations and high symmetry of the low-index directions.However,the simulated results coincide well with experimental pole figures in the high-index directions{123}_(bcc).A modified method with simplicity based on Miyamoto’s work was proposed.The results indicate that the ORs determined by modified method are similar to those determined by Miyamoto’method,that is,the OR is near K–S OR for the low-carbon Q–P–T steel,and with the increase of carbon content,the OR is closer to N–W OR in medium-carbon Q–P–T steel.     

Growth Kinetics of Single Inclusion Particle in Molten Melts

On the basis of the single-particle framework, a new theory on inclusion growth in metallurgical melts is developed to study the kinetics of inclusion growth on account of reaction and collision. The studies show that the early growth of inclusion depends on reaction growth and Brawnian motion collision, and where the former is decisive, the late growth depends on turbulence collision and Stokes＇ collision, and where the former is dominant; collision growth is very quick during the smelting process, lessened in the refining process, but nearly negligible in the continuous casting process.     

Theoretical Analysis for the Motion and Temperature of Melt Droplets in Spray Degassing Process

The motion of melt droplets in spray degassing process was analyzed theoretically. The height of the treatment tank in spray degassing process could be determined by the results of theoretical calculation of motion of melt droplets. To know whether the melt droplets would solidify during spraying process, the balance temperature of melt droplets was also theoretically analyzed. Then proof experiments for theoretical results about temperature of melt droplets were carried. In comparison, the experimental results were nearly similar to the calculation results.     

Using Finite Element and Contour Method to Evaluate Residual Stress in Thick Ti-6Al-4V Alloy Welded by Electron Beam Welding

This work was to reveal the residual stress profile in electron beam welded Ti-6Al-4V alloy plates(50 mm thick) by using finite element and contour measurement methods.A three-dimensional finite element model of 50-mmthick titanium component was proposed,in which a column–cone combined heat source model was used to simulate the temperature field and a thermo-elastic–plastic model to analyze residual stress in a weld joint based on ABAQUS software.Considering the uncertainty of welding simulation,the computation was calibrated by experimental data of contour measurement method.Both test and simulated results show that residual stresses on the surface and inside the weld zone are significantly different and present a narrow and large gradient feature in the weld joint.The peak tensile stress exceeds the yield strength of base materials inside weld,which are distinctly different from residual stress of the thin Ti-6Al-4V alloy plates presented in references before.     

Microstructures and Tensile Properties of Ultrafine-Grained Ni–(1–3.5) wt% SiC_(NP) Composites Prepared by a Powder Metallurgy Route

Silicon carbide nanoparticle-reinforced nickel-based composites(Ni–Si CNP),with a Si CNPcontent ranged from1 to 3.5 wt%,were prepared using mechanical alloying and spark plasma sintering.In addition,unreinforced pure nickel samples were also prepared for comparative purposes.To characterize the microstructural properties of both the unreinforced pure nickel and the Ni–Si CNPcomposites transmission electron microscopy(TEM) was used,while their mechanical behavior was investigated using the Vickers pyramid method for hardness measurements and a universal tensile testing machine for tensile tests.TEM results showed an array of dislocation lines decorated in the sintered pure nickel sample,whereas,for the Ni–Si CNPcomposites,the presence of nano-dispersed Si CNPand twinning crystals was observed.These homogeneously distributed Si CNPwere found located either within the matrix,between twins or on grain boundaries.For the Ni–Si CNPcomposites,coerced coarsening of the Si CNPassembly occurred with increasing Si CNPcontent.Furthermore,the grain sizes of the Ni–Si CNPcomposites were much finer than that of the unreinforced pure nickel,which was considered to be due to the composite ball milling process.In all cases,the Ni–Si CNPcomposites showed higher strengths and hardness values than the unreinforced pure nickel,likely due to a combination of dispersion strengthening(Orowan effects) and particle strengthening(Hall–Petch effects).For the Ni–Si CNPcomposites,the strength increased initially and then decreased as a function of Si CNPcontent,whereas their elongation percentages decreased linearly.Compared to all materials tested,the Ni–Si CNPcomposite containing 1.5% Si C was found more superior considering both their strength and plastic properties.