Improved interfacial properties of carbon fiber-reinforced epoxy composites with Fe2O3/graphene nanosheets using a magnetic field

The performance of carbon fiber-reinforced composites largely depends on the properties of the fiber-matrix interface. Here, to improve the interfacial strength properties of carbon fiber/epoxy composites, we doped different concentrations of Fe₂O₃/graphene nanosheets onto the interfacial region of the carbon fiber composites by nano-coating technology. With the aid of the magnetic field, the arrangement of nanosheets could be controlled in the interface. The nanosheets can be arranged on the carbon fiber surface parallel or perpendicularly with different concentrations. The tensile strength and interfacial shear strength of the modified fiber microcomposites had increased by 22.1 and 44.4% respectively with 1.0 mg/mL Fe₂O₃/graphene nanosheets. The results indicated that the Fe₂O₃/graphene nanosheets have an important influence on the carbon fibers and carbon fibers composites.     

Mechanical properties of carbon fiber composites modified with nano-SiO2 in the interphase

The performance of carbon fibers-reinforced composites is dependent to a great extent on the properties of fiber–matrix interface. To improve the interfacial properties in carbon fibers/epoxy composites, nano-SiO₂ particles were introduced to the surface of carbon fibers by sizing treatment. Atomic force microscope (AFM) results showed that nano-SiO₂ particles had been introduced on the surface of carbon fibers and increase the surface roughness of carbon fibers. X-ray photoelectron spectroscopy (XPS) showed that nano-SiO₂ particles increased the content of oxygen-containing groups on carbon fibers surface. Single fiber pull-out test (IFSS) and short-beam bending test (ILSS) results showed that the IFSS and ILSS of carbon fibers/epoxy composites could obtain 30.8 and 10.6% improvement compared with the composites without nano-SiO₂, respectively, when the nano-SiO₂ content was 1 wt % in sizing agents. Impact test of carbon fibers/epoxy composites treated by nano-SiO₂ containing sizing showed higher absorption energy than that of carbon fibers/epoxy composites treated by sizing agent without nano-SiO₂. Scanning electron microscopy (SEM) of impact fracture surface showed that the interfacial adhesion between fibers and matrix was improved after nano-SiO₂-modified sizing treatment. Dynamic mechanical thermal analysis (DMTA) showed that the introduction of nano-SiO₂ to carbon fibers surface effectively improved the storage modulus of carbon fibers/epoxy.     

Foreword

The effect of surface treatments and fiber sizings on the stress transfer characteristics and composite properties of AS-4 carbon/epoxy materials has been determined. Fiber surface chemistry was systematically varied from acidic to basic with RF glow discharge plasmas of CO₂ and NH₃ and characterized with ESCA techniques. Sizings applied to some of the treated fibers consisted of diglycidyl ether of bisphenol-A(DGEBA). Single fiber tension tests were used to measure the interfacial shear strength of samples made with DGEBA/metaphenylene diamine resin. Short beam shear and transverse flexure tests were used to examine the composite properties of modified materials.

Results showed that the plasma treatments were effective in altering the surface chemistry of the fiber but that changes in surface chemistry had surprisingly little effect on the critical stress transfer length. Sizing had a more significant effect on the transfer length. The interlaminar shear strength of the composites were unaffected by the treatments. Transverse flexure tests were more sensitive to the changes in surface characteristics. The work indicates that the interface properties of AS-4 fibers are close to optimal but that improvements in composite performance are possible through interphase formation.     

Effect of Atmospheric Plasma Treatment on Carbon Fiber/Epoxy Interfacial Adhesion

In this work the effect of atmospheric plasma treatment on carbon fiber has been studied. The carbon fibers were treated for 1, 3 and 5 min with a He/O₂ dielectric barrier discharge atmospheric pressure plasma. The fiber surface morphology, surface chemical composition and interfacial shear strength between the carbon fiber and epoxy resin were investigated using atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS) and the single fiber composite fragmentation test. Compared to untreated carbon fibers, the plasma treated fiber surfaces exhibited surface morphological and surface composition changes. The fiber surfaces were found to be roughened, the oxygen content on the fiber surfaces increased, and the interfacial shear strength (IFSS) improved after the atmospheric pressure plasma treatment. The fiber strength showed no significant changes after the plasma treatment.     

Carbon fiber‐reinforced gelatin composites. I. Preparation and mechanical properties

Composites were made from carbon fibers and gelatin using a solvent‐casting or solution‐impregnation technique. Relationships between the fiber volume fraction (Vf), glycerol (plasticizer) content, gelatin content, fiber form, and mechanical properties (tensile strength and modulus, elongation at break, and shear strength) of the composites were investigated. In long carbon fiber gelatin composite (C_L/Gel), tensile strength, modulus, and shear strength increased steadily with the Vf. In the case of a short carbon fiber gelatin composite (C_S/Gel), an initial improvement in tensile strength and modulus was followed by a reduction, whereas the shear strength improved with the Vf and then reached a constant value. The elongation decreased with the Vf for both composites. It is shown that C_L/Gel had higher values of strength, modulus, and elongation than did C_S/Gel at any Vf level. The effects of glycerol and gelatin contents on the mechanical properties of the composites were found to be much less significant as compared to the Vf. According to scanning electron microscopic observation of the fracture surfaces, the fibers were uniformly distributed in the gelatin matrix, but the interfacial adhesion between the gelatin matrix and the carbon fibers was not very good for both composites. Fiber surface modification would be necessary to further improve the mechanical properties of the two composites. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 987–993, 2000     

Enhanced interfacial strength and mechanical properties of carbon fiber composites by introducing functionalized silica nanoparticles into the interface

Introducing nanoparticles onto the surface of carbon fibers (CFs) is a useful method for enhancing the quality of fiber-matrix interface. In this work, a liquid sizing agent containing functionalized silica nanoparticles (SiO₂) was well prepared to improve interfacial strength and mechanical properties of composites. In order to enhance the dispersion of SiO₂ nanoparticles in sizing agent, SiO₂ nanoparticles were chemically grafted with 3-aminopropyltriethoxysilane (APS), and then silanized silica (SiO₂-APS) was introduced into the interphase by a conventional sizing process as well. Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), and thermogravimetric analysis (TGA) confirmed the successful preparation of SiO₂-APS. Scanning electron microscopy (SEM) showed that a uniform distribution of SiO₂-APS on the fiber surface and the increased surface roughness. The sized fibers (CF/SiO₂-APS) exhibited a high surface free energy and good wettability based on a dynamic contact angle testing. Interfacial microstructure and mechanical properties of untreated and sized CFs composites were investigated. Simultaneous enhancements of interlaminar shear strength (ILSS) and impact toughness of CF/SiO₂-APS composites were achieved, increasing 44.79% in ILSS and 31.53% in impact toughness compared to those of untreated composites. Moreover, flexural strength and modulus of composites increased by 32.22 and 50.0% according to flexural test. In addition, the hydrothermal aging resistance of CF/SiO₂-APS composites has been improved significantly owing to the introduced Si-O-Si bonds at the interface.     

Kevlar fiber–epoxy adhesion and its effect on composite mechanical and fracture properties by plasma and chemical treatment

Kevlar 49 fibers were surface-modified by NH₃-, O₂-, and H₂O-plasma etching and chlo-rosulfonation and subsequent reaction with some reagents (glycine, deionized water, eth-ylendeiamine, and 1-butanol) to improve the adhesion to epoxy resin. After these treatments, the changes in fiber topography, chemical compositions of the fiber surfaces, and the surface functional groups introduced to the surface of fibers were identified by SEM, XPS, and static SIMS. Interlaminar shear strength (ILSS) and T-peel strenght between the fiber and opoxy resin, as measured by the short-beam test and T-peel test, were remarkedly improved by gas plasma and chlorosulfonation (0.1% and 0.25% CISO₃H at 30 s). However, from the results of similar G_IC values of the treated and untreated fiber composites, it is clear that the fiber/matrix interfacial bond strength is only a minor contributor to G_IC. SEM was also used to study the surface topography of the fracture surfaces of composites in T-peel test. It could be seen from SEM observations that the improvement of fiber/matrix interfacial bond strength often accompanied a change in fracture mode from the interface of fiber/epoxy resins to the fiber fibrillation and the resins. © 1996 John Wiley & Sons, Inc.     

CO2 plasma modification of high-modulus carbon fibers and their adhesion to epoxy resins

Interfacial bond strength is often a performance-limiting factor of carbon-fiber-reinforced composites. This limitation is most prevalent when higher-modulus fibers or relatively unreactive matrix resins, such as engineering thermoplastics or high-temperature thermoset resin systems, are used. Radio-frequency (RF) glow discharge plasmas are an effective means of modifying carbon-fiber surface chemical characteristics to promote adhesion. It has been previously shown that oxidizing plasmas are especially effective compared with electro-oxidative treatments for treating carbon fiber surfaces as revealed by titrations, electron spectroscopy, wetting, and inverse gas chromatography measurements. This study evaluated the effectiveness of CO₂ plasmas on two experimental high-modulus carbon/graphite fibers and correlated the plasma surface modification with interfacial adhesion in an epoxy matrix composite system. The results show that CO₂ plasma treatment increased the surface oxygen content by nearly a factor of 2 over typical electro-oxidation treatments. The increased oxygen is mainly in the form of hydroxyl, ketone, and carboxyl-like moieties. Unidirectional composites were prepared from as-received and plasma-modified versions of each type of experimental fiber. The composites containing plasma-modified filaments exhibited 1.5-3.0 times the strength of composites fabricated with untreated or electro-oxidized filaments in transverse-flexural tests. Short-beam shear strength increased by two times over those with as-produced filaments and is equivalent to that of composites containing electro-oxidized filaments.     

Influence of oxygen plasma treatment parameters on the properties of carbon fiber

This study is focused on the impact of oxygen plasma treatment on properties of carbon fibers and interfacial adhesion behavior between the carbon fibers and epoxy resin. The influences of the main parameters of plasma treatment process, including duration, power, and flow rate of oxygen gas were studied in detail using interlaminar shear strength (ILSS) of carbon fiber composites. The ILSS of composites made of carbon fibers treated by oxygen plasma for 1 min, at power of 125 W, and oxygen flow rate of 100 sccm presented a maximum increase of 28% compared to composites made of untreated carbon fibers. Furthermore, carbon fibers were characterized by scanning electron microscopy (SEM), tensile strength test, attenuated total reflectance Fourier transform infrared (ATR-FTIR), and Raman spectroscopy analyses. It was found that the concentration of reactive functional groups on the fiber surface was increased after the plasma modification, as well the surface roughness, which finally improved the interfacial adhesion between carbon fibers and epoxy resin. However, high power and long exposure times could partly damage the surface of carbon fibers and decrease the tensile strength of filaments and ILSS of treated fiber composites.     

RETRACTED ARTICLE: Surface modification of aramid fibers with novel chemical approach

Friedel–Crafts Reaction as a simple and convenient approach to the surface modification of aramid fiber was introduced in this paper. Epoxy chloropropane was chosen as the treatment reagent to modify aramid fibers surface via Graft reaction. After the modification, the interfacial properties of aramid/epoxy composites were investigated by the single fiber pull-out test (SFP), and the mechanical properties of aramid fibers were investigated by the tensile strength test. The results showed that the interfacial shear strength (IFSS) value of aramid/epoxy composites was enhanced by about 50%, and the tensile strength of aramid fibers had no obvious damage. The crystalline state of aramid fibers was determined by X-ray diffraction instrument (XRD), and the results showed that there were not any distinct crystal type varieties. The surface elements of aramid fibers were determined by X-ray photoelectron spectroscopy (XPS), the analysis of which showed that the oxygen/carbon ratio of aramid fiber surface increased obviously. The possible changes of the chemical structure of aramid fibers were investigated via Fourier transform infrared spectrum (FTIR), and the analysis of which showed that the epoxy functional groups were grafted into the molecule structure of aramid fibers. The surface morphology of aramid fibers was analyzed by Scanning electron microscope (SEM), and the SEM results showed that the physical structure of aramid fibers was not etched or damaged obviously. The surface energy of aramid fibers was investigated via the dynamic capillary method, and the results showed that the surface energy was enhanced by 31.5%, and then the wettability degree of aramid fiber surface was enhanced obviously too. All of the results indicated that this novel chemical modification approach not only can improve the interfacial bonding strength of aramid/epoxy composites remarkably, but also have no negative influence on the intrinsic tensile strength of aramid fibers.     

Temperature effect on graphene‐filled interface between glass–carbon hybrid fibers and epoxy resin characterized by fiber‐bundle pull‐out test

The overall mechanical performance of glass–carbon hybrid fibers reinforced epoxy composites depends heavily upon fiber–matrix interfacial properties and the service temperatures. Fiber‐bundle pull‐out tests of glass (GF) and/or carbon fiber (CF) reinforced epoxy composites were carried out at room and elevated temperatures. Graphene nanoplatelets were added in the interfacial region to investigate their influence on the interfacial shear strength (IFSS). Results show that IFSS of specimens with fiber‐bundle number ratio of GF:CF = 1:2 is the largest among the hybrid composites, and a positive hybridization effect is found at elevated temperatures. IFSS of all the specimens decreases with the increasing of test temperatures, while the toughness shows a contrary tendency. As verified by scanning electron microscopy observations, graphene nanoplatelets on fiber surface could enhance the IFSS of pure glass/carbon and hybrid fibers reinforced epoxy composites at higher temperatures significantly. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46263.     

Surface ammonification of the mutual‐irradiated aramid fibers in 1,4‐dichlorobutane for improving interfacial properties with epoxy resin

The mutual irradiated aramid fibers in 1,4‐dichlorobutane was ammoniated by ammonia/alcohol solution, in an attempt to improve the interfacial properties between aramid fibers and epoxy matrix. Scanning electron microscopy (SEM), X‐ray photoelectron spectroscopy (XPS), dynamic contact angle analysis (DCA), interfacial shear strength (IFSS), and single fiber tensile testing were carried out to investigate the functionalization process of aramid fibers and the interfacial properties of the composites. Experimental results showed that the fiber surface elements content changed obviously as well as the roughness through the radiation and chemical reaction. The surface energy and IFSS of aramid fibers increased distinctly after the ammonification, respectively. The amino groups generated by ammonification enhanced the interfacial adhesion of composites effectively by participating in the epoxy resin curing. Moreover, benefited by the appropriate radiation, the tensile strength of aramid fibers was not affected at all. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44924.     

Effects of Surface Treatments on Mechanical Properties and Water Resistance of Kenaf Fiber-Reinforced Unsaturated Polyester Composites

Abstract

Effects of surface treatments on the strength and water resistance of kenaf fiber-reinforced unsaturated polyester (UPE) composites were investigated. A new coupling agent that consists of 1,6-diisocyanato-hexane (DIH) and 2-hydroxylethyl acrylate (HEA) was investigated for surface treatments of kenaf fibers. The surface treatments were found to significantly enhance the tensile strength, modulus of rupture, modulus of elasticity, and water resistance of the resulting kenaf–UPE composites. Fourier transform infrared spectroscopy (FTIR) confirmed that DIH-HEA was covalently bonded onto kenaf fibers. Scanning electron microscopy (SEM) images of the composites revealed that chemical treatment of kenaf fibers with a combination of DIH and HEA improved the interfacial adhesion between kenaf fibers and UPE resin in the DIH–HEA-treated kenaf–UPE composites. The mechanisms by which the chemical treatment of kenaf fiber surfaces improved strength and water resistance of the resulting kenaf–UPE composites were discussed.     

臭氧处理对碳纤维表面及其复合材料性能的影响

利用X射线光电子能谱(XPS)研究了碳纤维经臭氧(O3)氧化处理后表面元素组成及表面官能团的变化，结果发现，O3表面处理主要增加了碳纤维表面上的羟基或醚基官能团；研究了表面O3氧化处理对复合材料力学性能的影响，结果表明，碳纤维经O3氧化处理后明显改善了碳纤维与环氧树脂间的界面粘结，其复合材料的层间剪切强度明显提高。     

THE INFLUENCE OF OXIDATION OF THE FIBERS ON THE TRIBOLOGICAL PROPERTIES OF CARBON FIBER-REINFORCED NYLON COMPOSITES

Three-dimensional braided carbon fiber-reinforced nylon composites (C_3D/MCN) were prepared in order to investigate the influence of oxidation of carbon fibers on the tribological properties of the C_3D/MCN composites. Friction and wear tests of the C_3D/MCN composites with untreated and treated carbon fabric were conducted. The characteristics of the carbon fiber, the interface strength, the hardness, and the worn surface morphologies of the C_3D/MCN composites were analyzed. The results show that the specific surface area of treated carbon fiber was far higher than that of untreated carbon fiber and there formed a functional group of –C=O on the carbon fiber surface after air oxidation. The oxidation of the carbon fibers improved the interface strength between the carbon fibers and the matrix and had little effect on the hardness of the composites. The friction coefficient and wear rate of C_3D/MCN composites with oxidized carbon fibers were apparently lower than those with untreated carbon fibers. In conclusion, the oxidation of the fibers showed good effects on the improvement of the interface strength and the tribological properties of the composites.     

Nanoscale toughening of carbon fiber‐reinforced epoxy composites through different surface treatments

Interests in improving poor interfacial adhesion in carbon fiber‐reinforced polymer (CFRP) composites has always been a hotspot. In this work, four physicochemical surface treatments for enhancing fiber/matrix adhesion are conducted on carbon fibers (CFs) including acid oxidation, sizing coating, silane coupling, and graphene oxide (GO) deposition. The surface characteristics of CFs are investigated by Fourier transform infrared spectroscopy, X‐ray photoelectron spectroscopy, atomic force microscopy, scanning electron microscopy, interfacial shear strength, and interlaminar shear strength. The results showed that GO deposition can remarkably promote fiber/matrix bonding due to improved surface reactivity and irregularity. In comparison, epoxy sizing and acid oxidation afford enhancement of IFSS owing to effective molecular chemical contact and interlocking forces between the fiber and the matrix. Besides, limited covalent bonds between silane coupling and epoxy matrix cannot make up for the negative effects of excessive smoothness of modified CFs, endowing them inferior mechanical properties. Based on these results, three micro‐strengthening mechanisms are proposed to broadly categorize the interphase micro‐configuration of CFRP composite, namely, “Etching” “Coating”, and “Grafting” modifications, demonstrating that proper treatments should be chosen for combining optimum interfacial properties in CFRP composites. POLYM. ENG. SCI., 59:625–632, 2019. © 2018 Society of Plastics Engineers     

Plasma etching and plasma polymerization coating of carbon fibers. Part 1. Interfacial adhesion study

Unsized AS-4 carbon fibers were etched by RF plasma and then coated via plasma polymerization in order to enhance their adhesion to vinyl ester resin. Gases utilized for plasma etching were Ar, N₂ and O₂, while monomers used in plasma polymerization coating were acetylene, butadiene and acrylonitrile. Plasma etchings were carried out as a function of plasma power (30–70 W), treatment time (1–10 min) and gas pressure (20–40 mtorr). Plasma polymerizations were performed by varying the treatment time (15–60 s), plasma power (10–30 W) and gas pressure (20-40 mtorr). The conditions for plasma etching and plasma polymerization were optimized by measuring interfacial adhesion with vinyl ester resin via micro-droplet tests. Plasma etched and plasma polymer coated carbon fibers were characterized by SEM, XPS, FT-IR and α-Step, dynamic contact angle analyzer (DCA) and tensile strength measurements. In Part 1, interfacial adhesion of plasma etched and plasma polymer coated carbon fibers to vinyl ester resin is reported, while characterization results including tensile strength of carbon fibers are reported in Part 2. Among the treatment conditions, a combination of Ar plasma etching and acetylene plasma polymer coating provided greatly improved interfacial shear strength (IFSS) of 69 MPa, compared to 43 MPa obtained from as-received carbon fiber. Based on the SEM analysis of failure surfaces and load-displacement curves, the failure was found to occur at the interface between plasma polymer coating and vinyl ester resin.     

Improvements in interfacial and heat-resistant properties of carbon fiber/methylphenylsilicone resins composites by incorporating silica-coated multi-walled carbon nanotubes

The multi-scale reinforcement and interfacial strengthening on carbon fiber (CF)-reinforced methylphenylsilicone resin (MPSR) composites by adding silica-coated multi-walled carbon nanotubes (SiO₂-CNTs) were investigated. SiO₂-CNT has been successfully prepared via the hydrolysis of tetraethoxysilane in the presence of acid-oxidized multi-walled carbon nanotubes. Transmission electron microscopy, X-ray diffraction, and Fourier Transform infrared spectroscopy were carried out to examine the functional groups and structures of CNTs. Then, SiO₂-CNT was incorporated into MPSR matrix to prepare CF/MPSR-based composites by the compression molding method. The effects of the introduced SiO₂-CNT on the interfacial, impact, and heat-resistant properties of CF/MPSR composites were evaluated by short-beam bend method, impact test, and thermal oxygen aging experiments, respectively. Experimental results revealed that the CF/MPSR composites reinforced with 0.5 wt% SiO₂-CNT showed a significant increase 34.53% in the interlaminar shear strength (ILSS) and 20.10% in impact properties. Moreover, the heat-resistant properties of composites were enhanced significantly by adding SiO₂-CNT hybrid nanoparticles. These enhancements are mainly attributed to the improved matrix performance resulted from the molecular-level dispersion of SiO₂-CNT in MPSR matrix and the strong interfacial adhesion between SiO₂-CNT and matrix resin, which are beneficial to improve the mechanical stress transfer from MPSR matrix to CFs reinforcement and alleviate stress concentrations.     

Improvement of Interfacial Adhesion of Glass Fiber/Epoxy Composite by Using Plasma Polymerized Glass Fibers

This study intends to produce plasma polymer thin films of γ-glycidoxypropyltrimethoxysilane (γ-GPS) on glass fibers in order to improve interfacial adhesion of glass fiber-reinforced epoxy composites. A low frequency (LF) plasma generator was used for the plasma polymerization of γ-GPS on the surface of glass fibers at different plasma powers and exposure times. X-ray photoelectron spectroscopy (XPS) and SEM analyses of plasma polymerized glass fibers were conducted to obtain some information about surface properties of glass fibers. Interlaminar shear strength (ILSS) values and interfacial shear strength (IFSS) of composites reinforced with plasma polymerized glass fiber were evaluated. The ILSS and IFSS values of non-plasma polymerized glass fiber-reinforced epoxy composite were increased 110 and 53%, respectively, after plasma polymerization of γ-GPS at a plasma power of 60 W for 30 min. The improvement of interfacial adhesion was also confirmed by SEM observations of fractured surface of the composites.     

Plasma surface treatments on carbon fibers. II. Mechanical property and interfacial shear strength

Carbon fiber are surface treated by oxygen, argon, and styrene plasma to study the effects on fiber strength and interfacial shear strength with PPS resin. Interfacial shear strength between carbon fiber and high melting temperature thermoplastic resins is successfully measured with the microbond pull-out test with the help of scanning CO₂ laser beam which solved the difficulties in preparing PPS microspheres. Tensile tests show that etching by oxygen plasma and deposition with plasma–PS increase strength of the fibers in some cases. ESCA spectra deconvolutions demonstrate that the improved interfacial strength is strongly related to the hydroxyl, ether, or aromatic groups on the surface. On the other hand, hydrocarbon segments are detrimental to the interface. Surface area and roughness have little influences on the interfacial strength of carbon fiber/PPS composites.