Characterization of eva-based adhesives containing different amounts of rosin ester or polyterpene tackifier

Different amounts (50-170 php--parts per hundred parts of EVA, 33-63 wt%) of two tackifiers (hydrogenated rosin ester, polyterpene resin) were added to an ethylene vinyl acetate (EVA) copolymer containing 28 wt% vinyl acetate. The EVA and the tackifier were characterized using infrared (IR) spectroscopy, DSC measurements, and stress-controlled plate-plate rheology. The properties and compatibility of the EVA-tackifier mixtures were studied using DSC, DMTA, and stress-controlled plate-plate rheology. Immediate adhesion was measured as a quantification of tack, and the T-peel strength of roughened styrene-butadiene rubber/EVA-tackifier adhesive joints was also obtained. The increase in the amount of tackifier noticeably changed the crystallinity of polyethylene blocks in the EVA, and the temperature at the cross-over between the curves of the storage and loss moduli as a function of the temperature was displaced to a lower value. Whereas the hydrogenated rosin ester was compatible with the amorphous ethylene vinyl acetate copolymer regions of the EVA (Tg value increased) reducing its crystallinity, the polyterpene resin was compatible with the polyethylene blocks of the EVA (T g value was not modified), increasing its crystallinity. Immediate adhesion of the EVA-tackifier mixtures was improved by adding both hydrogenated rosin ester and polyterpene tackifiers. On the other hand, there was an optimum tackifier content at which the maximum T-peel strength value was obtained.     

CHARACTERIZATION OF EVA-BASED ADHESIVES CONTAINING DIFFERENT AMOUNTS OF ROSIN ESTER OR POLYTERPENE TACKIFIER

Different amounts (50-170 php--parts per hundred parts of EVA, 33-63 wt%) of two tackifiers (hydrogenated rosin ester, polyterpene resin) were added to an ethylene vinyl acetate (EVA) copolymer containing 28 wt% vinyl acetate. The EVA and the tackifier were characterized using infrared (IR) spectroscopy, DSC measurements, and stress-controlled plate-plate rheology. The properties and compatibility of the EVA-tackifier mixtures were studied using DSC, DMTA, and stress-controlled plate-plate rheology. Immediate adhesion was measured as a quantification of tack, and the T-peel strength of roughened styrene-butadiene rubber/EVA-tackifier adhesive joints was also obtained. The increase in the amount of tackifier noticeably changed the crystallinity of polyethylene blocks in the EVA, and the temperature at the cross-over between the curves of the storage and loss moduli as a function of the temperature was displaced to a lower value. Whereas the hydrogenated rosin ester was compatible with the amorphous ethylene vinyl acetate copolymer regions of the EVA (Tg value increased) reducing its crystallinity, the polyterpene resin was compatible with the polyethylene blocks of the EVA (T g value was not modified), increasing its crystallinity. Immediate adhesion of the EVA-tackifier mixtures was improved by adding both hydrogenated rosin ester and polyterpene tackifiers. On the other hand, there was an optimum tackifier content at which the maximum T-peel strength value was obtained.     

Synthesis and characterization of new thermoplastic polyurethane adhesives containing rosin resin as an internal tackifier

Three thermoplastic polyurethane elastomers (TPUs) were prepared using the prepolymer method. MDI (diphenylmethane-4,4′-diisocyanate) and the polyadipate of 1,4-butanediol (M_w = 2400) were reacted to produce a prepolymer containing unreacted isocyanate groups; chain extenders were different mixtures of 1,4-butanediol and a rosin resin (0-50%). The specific feature of this procedure was the introduction of a rosin resin as an internal tackifier to provide higher immediate adhesion to the TPUs. The new TPUs were characterized using gel permeation chromatography, wideangle X-ray diffraction, differential scanning calorimetry, stress-controlled rheology, and stress-strain measurements. The TPUs were used as raw materials to prepare solvent-based polyurethane adhesives, the adhesion properties of which were obtained from T-peel tests on PVC/polyurethane adhesive/PVC and leather/polyurethane adhesive/PVC joints. The addition of rosin resin as an internal tackifier contributed to the production of two types of hard segments, which affected the properties of the TPUs. Therefore, rosin resin as an internal tackifier produced an increase in the average molecular weight, an increase in the viscosity, and improved the rheological properties. The glass transtition temperature decreased if the TPUs contained rosin resin, due to a greater degree of incompatibility between the hard and soft segments. Consequently, slower kinetics of crystallization was obtained in the TPUs containing rosin resin. Depending on the amount of rosin resin in the TPU, different structures and properties were obtained. On the other hand, the immediate T-peel strength in all joints was improved if the TPU contained rosin resin.     

Characterization of thermoplastic polyurethane adhesives with different hard/soft segment ratios containing rosin as an internal tackifier

Three thermoplastic polyurethanes (TPUs) containing different hard/soft (h/s) segment ratios (1.05-1.4) were prepared using the prepolymer method. MDI (diphenylmethane-4,4′diisocyanate) and polyadipate of 1,4-butanediol (M _w = 2440) were allowed to react to produce the prepolymer. To provide the polyurethanes with high immediate adhesion to different substrates, a rosin + 1,4-butanediol mixture (1 : 1 equivalent%) was used as chain extender (TPU-Rs). These TPU-Rs had two types of hard segments: (i) Urethane hard segments, produced by reaction of the isocyanate and the 1,4-butanediol, and (ii) Urethan-amide hard segments, produced by reaction of the isocyanate and the carboxylic acid functionality of the rosin. The TPUs and TPU-Rs were characterized using FTIR spectroscopy, gel permeation chromatography, differential scanning calorimetry, stress-controlled plate-plate rheology, stress-strain measurements, and Brookfield viscosity. The TPUs and TPU-Rs were used as raw materials to prepare solvent-based polyurethane adhesives, the adhesion properties of which were obtained from T-peel tests on PVC/polyurethane adhesive/PVC joints. The addition of rosin as an internal tackifier increased the average molecular weight, more markedly in the TPU-Rs containing higher hard/soft segment ratios, but the elastic and viscous moduli decreased. An increase in the hard/soft segment ratio of the TPU-Rs retarded the kinetics of crystallization (which was determined by the soft segment content in the polyurethane), and increased the immediate T-peel strength in PVC/polyurethane adhesive/PVC joints (which was determined by the urethan-amide hard segments). Furthermore, addition of rosin to the polyurethanes decreased the final adhesion, although always reasonably high peel strength values were obtained.     

The viscoelastic properties of rubber–resin blends. II. The effect of resin molecular weight

In blends of rubber and low molecular weight resins, the compatibility of the system controls the viscoelastic properties and ultimately the performance of the composition as a pressure sensitive adhesive. The effect of the resin molecular weight on compatibility was examined by studying rubber–resin blends prepared from resins which represent a range of molecular weights. Viscoelastic properties were measured using a mechanical spectrometer on 1:1 blends of rubber and a series of polystyrene resins and poly(vinylcyclohexane) resins. Based on plots of G′ and tan δ vs. temperature, blends of natural rubber and polystyrene resin show incompatibility at resin M_w of about 600 and above. Blends of natural rubber and poly(vinyl cyclohexane) are incompatible at resin M_w of about 1800, but are compatible at M_w of about 650. Blends of styrene–butadiene rubber and polystyrene resins are compatible at resin M_w of about 650 but appear to contain a low volume incompatible phase at M_w of about 900. Therefore, the compatibility of a rubber–resin blend depends upon the molecular weight of the resin. Even systems expected to be compatible will show evidence of incompatibility as the molecular weight of the resin is raised above some limiting value.     

Synthesis and characterization of hydrogenated sorbic acid grafted dicyclopentadiene tackifier

Hydrocarbon resins, which are defined as low molecular weight, amorphous, and thermoplastic polymers, are widely used as tackifier for various types of adhesives, as processing aids in rubber compounds, and as modifiers for paint and ink products, and for plastics polymers such as isotactic polypropylene. Typically, hydrocarbon resins are non-polar, and thus highly compatible with non-polar rubbers and polymer. However, they are poorly compatible with polar system, such as acrylic copolymer, polyurethanes, and polyamides. Moreover, recently the raw materials of tackifier from naphtha cracking had been decreased because of light feed cracking such as gas cracking. To overcome this problem, in this study, novel hydrocarbon resins were designed to have a highly polar chemical structure. And, it was synthesized by Diels–Alder reaction of dicyclopentadiene monomer and sorbic acid from blueberry as renewable resources. Acrylic resins were formulated with various tackifiers solution including hydrogenated sorbic acid grafted dicyclopentadiene tackifier in acrylic adhesive and rolling ball tack, loop tack, 180° peel adhesion strength, and shear adhesion strength were measured. The properties depend on the softening point and polar content of tackifiers.     

Effects of the compatibility of a polyacrylic block copolymer/tackifier blend on the phase structure and tack of a pressure‐sensitive adhesive

Adhesion and viscoelastic properties and morphology of a polyacrylic block copolymer/tackifier blend were investigated. Special rosin ester resins with different weight average molecular weights of 650, 710, 890, and 2160 were used as the tackifier and blended with a polyacrylic block copolymer consisting of poly(methyl methacrylate) and poly(n‐butyl acrylate) blocks at tackifier content levels of 10, 30, and 50 wt %. The compatibility decreased with an increase in molecular weight. From TEM observation, the number of formed agglomerates of the tackifier with sizes on the order of several tens of nanometers increased with increasing tackifier content and molecular weight of the tackifier in the range from 650 to 890. For the tackifier with a molecular weight of 2160, micrometer‐sized agglomerates were observed. The storage modulus at low temperature and the glass transition temperature of adhesive measured by a dynamic mechanical analysis increased dependent on the number of formed nanometer sized agglomerates. Tack was measured using a rolling cylinder tack tester over wide temperature and rolling rate ranges, and master curves were prepared in accordance with the time‐temperature superposition law. Tack and peel strength were optimum at a blend combination of intermediate compatibility, i.e., the molecular weight of 890. These optimum properties were correlated to maximal values of the storage modulus at room temperature and the glass transition temperature. Therefore, it was found that these features of blend properties are strongly affected by the nanometer sized agglomerates of tackifier. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Fundamental Understanding in Rolling Ball Tack of Tackified Block Copolymer Adhesives

In the pressure sensitive adhesive (PSA) industry, rolling ball tack is a very common tack test, which is simple, inexpensive and easy to operate. This work attempts to search for key parameter(s), which will affect the rolling ball tack of a PSA based on a blend of styrene-isoprene-styrene triblock copolymer(SIS) and hydrocarbon tackifier(s). We want to better understand whether this particular PSA performance is controlled by the surface or bulk properties of the adhesive.

Firstly, to test the contribution from the surface properties, we employ a model system of SIS/aliphatic tackifier in 1/1 wt. ratio as the control. Part of the tackifier in this PSA is then replaced by various amounts of low molecular weight diluents with different surface tensions. The idea is to vary the surface properties of the PSA because these low surface tension and low molecular weight diluents tend to migrate to the PSA surface. It is observed that the incorporation of a lower surface tension and a lower molecular weight diluent in the PSA tends to produce a larger increase in rolling ball tack compared with the unmodified PSA. On the other hand, the incorporation of a higher surface tension and a more compatible diluent tends to produce a larger increase in loop, peel and quick stick. Each diluent lowers the shear adhesion failure temperature (SAFT) of the diluent-modified PSA. These observations are explained in terms of tackifier molecular weight, and surface tension and compatibility of the various components (polyisoprene, tackifier, diluent and oil) in the adhesive formulation.

Secondly, to test the contribution from the bulk properties, we derive an equation for rolling ball tack in terms of the bulk viscoelastic behavior of the block copolymer PSA. However, experimental values of rolling ball tack do not follow this equation. Also, with increasing tackifier concentration in SIS, rolling ball tack has very different behavior compared with loop, peel, quick stick and probe tack. The latter set of performance criteria is known to be related to PSA bulk viscoelastic behavior. Therefore, these suggest that rolling ball tack is related more to the surface properties than to the bulk properties of the adhesive based on these results and those of the diluent-modified PSA systems.     

Fundamental Understanding in Rolling Ball Tack of Tackified Block Copolymer Adhesives

In the pressure sensitive adhesive (PSA) industry, rolling ball tack is a very common tack test, which is simple, inexpensive and easy to operate. This work attempts to search for key parameter(s), which will affect the rolling ball tack of a PSA based on a blend of styrene-isoprene-styrene triblock copolymer(SIS) and hydrocarbon tackifier(s). We want to better understand whether this particular PSA performance is controlled by the surface or bulk properties of the adhesive.

Firstly, to test the contribution from the surface properties, we employ a model system of SIS/aliphatic tackifier in 1/1 wt. ratio as the control. Part of the tackifier in this PSA is then replaced by various amounts of low molecular weight diluents with different surface tensions. The idea is to vary the surface properties of the PSA because these low surface tension and low molecular weight diluents tend to migrate to the PSA surface. It is observed that the incorporation of a lower surface tension and a lower molecular weight diluent in the PSA tends to produce a larger increase in rolling ball tack compared with the unmodified PSA. On the other hand, the incorporation of a higher surface tension and a more compatible diluent tends to produce a larger increase in loop, peel and quick stick. Each diluent lowers the shear adhesion failure temperature (SAFT) of the diluent-modified PSA. These observations are explained in terms of tackifier molecular weight, and surface tension and compatibility of the various components (polyisoprene, tackifier, diluent and oil) in the adhesive formulation.

Secondly, to test the contribution from the bulk properties, we derive an equation for rolling ball tack in terms of the bulk viscoelastic behavior of the block copolymer PSA. However, experimental values of rolling ball tack do not follow this equation. Also, with increasing tackifier concentration in SIS, rolling ball tack has very different behavior compared with loop, peel, quick stick and probe tack. The latter set of performance criteria is known to be related to PSA bulk viscoelastic behavior. Therefore, these suggest that rolling ball tack is related more to the surface properties than to the bulk properties of the adhesive based on these results and those of the diluent-modified PSA systems.     

Temperature dependence of tack and pulse NMR analysis of polystyrene block copolymer/tackifier system

The influence of tackifier structure on the temperature dependence of tack for a polystyrene block copolymer/tackifier system was investigated. A blend of polystyrene-block-polyisoprene-block- polystyrene triblock and polystyrene-block-polyisoprene diblock copolymers was used as the base polymer. Four different tackifiers were used: special rosin ester resin (RE), rosin phenolic resin (RP), hydrogenated cyclo-aliphatic resin (HC), and aliphatic petroleum resin (C5). Tack at 20?°C increased with the tackifier content for both RE and HC tackifier systems. Tack is affected by two factors: the work of adhesion at the adherend interface and the viscoelastic properties of the adhesive. The good balance of these two factors brought high tack. The adhesive with 10 wt.% tackifier exhibited the highest tack at 20?°C, whereas those with 30 and 50 wt.% tackifier were lower than those systems with 10 wt.% of the RP or C5 tackifiers. The adhesive with overly high hardness lowered the work of adhesion and the tack was not improved with more than 30 wt.%. A compatibility test in toluene solution and in solid state showed that tackifier RE has good compatibility with both polyisoprene and polystyrene, whereas tackifier RP has lower compatibility. Tackifiers HC and C5 had good compatibility with polyisoprene, but poor compatibility with polystyrene, and that of C5 was poorer. Pulse nuclear magnetic resonance (NMR) analyses indicated that tackifiers RE and HC effectively restrict the molecular mobility of polyisoprene phase.     

Tack and Shear Strength of Adhesives Prepared from Styrene-Butadiene Rubber (SBR) Using Gum Rosin and Petro Resin as Tackifiers

Tack and shear strength of styrene-butadiene rubber (SBR)-based pressure-sensitive adhesive were studied using gum rosin and petro resin as the tackifiers. The concentration of the tackifying resin was varied from 0 to 100 parts per hundred parts of rubber (phr). Toluene was used as the solvent throughout the experiment. The rolling ball technique was used to measure the tack of the adhesive, whereas, shear strength was determined by a TA-HDi Texture Analyser. Results show that the tack of the adhesive increases with increasing tackifier loadings for both tackifier systems. However, shear strength indicates the reverse behavior with increasing resin content, an observation which is attributed to the decrease in cohesive strength as the tackifier concentration is increased. Both tack and shear strength of the adhesives increases with molecular weight of SBR. Adhesive containing petro resin consistently exhibits higher values than the gum rosin system due to better wettability and compatibility in the former system.     

Phase structure and adhesion properties of acrylic block copolymer/tackifier blends as nanocomposite-like pressure-sensitive adhesives

In a blend of acrylic block copolymer consisting of poly(methyl methacrylate) and poly(n-butyl acrylate) blocks and a special rosin ester resin (RE) tackifier as a model pressure-sensitive adhesive (PSA), RE exists in two states: as nm-sized agglomerated particles (A) and as dissolved molecules (B). The effect of A and B ratio on the PSA properties were investigated using REs with four different weight-average molecular weights (M_ws) in the range from 680 to 1700. The formation of A increased with increasing of M_w because of lowering of miscibility. The glass transition temperature increased with increasing of M_w. The tack at lower temperatures and the fracture energy were improved by B, whereas the tack at higher temperatures was improved by A. A and B enhanced the cohesive strength and the wettability of PSA, respectively. However, the improvement of cohesive strength by the RE with highest M_w was remarkably low. This seems to be caused by the larger size of agglomerated particles. ¹H pulse nuclear magnetic resonance analysis was useful for estimating the degree of A formation. The model PSA investigated in this study was nanocomposite-like.     

Improving the heat‐resistance and toughness performance of phenolic resins by adding a rigid aromatic hyperbranched polyester

An aromatic hyperbranched polyester (AHBP) was synthesized by melt polycondensation from diphenolic acid and characterized by Fourier transform infrared spectrum (FTIR) spectra. The degree of branching (DB) value of AHBP calculated from the ¹³C‐NMR spectroscopy was 0.67. The number‐average molecular weight (M_n) and weight‐average molecular weight (M_w) of AHBP were 1792 and 4480 g/mol, respectively. Novel phenolic resins modified with AHBP (PR/AHBP) were then prepared, in which AHBP was used as toughener of phenolic resins. The effect of AHBP on the thermal properties of phenolic resins was studied by means of differential scanning calorimetry (DSC), thermal gravimetric analyses (TGA), and heat deformation temperature tests. The modified resins presented higher glass transition temperature (T_g) than the unmodified system due to that the rigid backbone structure of AHBP with a great deal of the benzene ring groups restricted the mobility of the chain segments of macromolecules. The DSC, scanning electron microscopy (SEM) analyses showed that AHBP had good compatibility with phenolic resin, and the modified resins showed ductile fracture. The results of mechanical performance measurements exhibited that the impact strength of PR/AHBP containing 15 wt % AHBP was about 130% higher than that of the neat phenolic resin, suggesting that the toughness of PR/AHBP was significantly improved by the addition of AHBP. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42734.     

Probing the viscoelastic properties of brominated isobutylene‐co‐p‐methylstyrene rubber/tackifier blends using a rubber process analyzer

The viscoelastic behavior of brominated isobutylene‐co‐p‐methylstyrene (BIMS) rubber/hydrocarbon resin blends and BIMS/phenol formaldehyde resin blends was studied with the use of a rubber process analyzer. Dynamic mechanical analysis and scanning electron microscopy were used to evaluate the compatibility between the BIMS/tackifier blends. Strain sweep tests at temperature below the softening point of the tackifiers showed the formation of resin–resin networks in the incompatible BIMS/phenolic resin blends. However, resin–resin network was not prominent in the case of the compatible BIMS/hydrocarbon resin blends. Frequency sweep tests were performed at the strain amplitude within the linear region at several temperatures and the variations of shear storage modulus, G′ and complex viscosity, η* against frequency were recorded. The tackifying resins modified the viscoelastic properties of the BIMS rubber by reducing the storage modulus at lower frequency and by increasing the storage modulus at higher frequencies. However, this action was found to be highly dependent on (a) rubber‐tackifier compatibility, (b) blend proportions, and (c) test temperature. Furthermore, stress relaxation measurements of the BIMS/tackifier blends at temperature below the softening point of the tackifiers showed longer period of relaxation for the incompatible BIMS/phenolic resin blends. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Polyols from epoxidized soybean oil and alpha hydroxyl acids and their adhesion properties from UV polymerization

Two types of biobased polyols, ESOGA and ESOLA, were synthesized from epoxidized soybean oil (ESO) with glycolic acid (GA) and lactic acid (LA), respectively, using a solvent-free/catalyst-free method. An ESO epoxy conversion rate of over 93% was achieved for both polyols. ESOGA has a weight-/number-average molecular weight (M_w/M_n) of 27,700/3900 g/mol and average hydroxyl functionality (f_OH) of 12.9, and ESOLA has M_w/M_n of 8800/3000 g/mol and f_OH of 11.7. The structures of the polyols were further characterized with Fourier transform infrared spectroscopy and ¹H-nuclear magnetic resonance. Rheology and thermal properties were studied with a rheometer and a differential scanning calorimeter. The polyols were polymerized with ESO to adhesive polymers using UV light in the presence of cationic photoinitiator. The curing rate decreased as the amount of polyol increased for resins based on ESOGA and ESOLA (EGA and ELA). With the same amount of polyol, ELA resins cured faster than EGA resins. The peel strength and tack of EGA and ELA adhesives increased significantly as the ratio of polyol in the resin increased. ELA exhibited obviously higher peel strength and tack than EGA with the same amount of polyol. All resin tapes exhibited high static shear values (20,000+min). Overall, both ESOGA and ESOLA exhibited great potential as polyols for pressure-sensitive adhesive applications.     

Compatibility and viscoelastic properties of brominated isobutylene‐co‐p‐methylstyrene rubber/tackifier blends

Brominated isobutylene‐co‐p‐methylstyrene (BIMS) rubber has been blended with hydrocarbon resin tackifier and alkyl phenol formaldehyde resin tackifier, and the compatibility between the blend components has been systematically evaluated. Dynamic mechanical analysis (DMA) and differential scanning calorimetry (DSC) studies show that BIMS rubber and hydrocarbon resin tackifier blends are compatible at all blend proportions studied. However, BIMS rubber and phenol formaldehyde resin blends exhibit very limited compatibility with each other and phase separation even at very low phenolic tackifier concentration. Morphological studies of the rubber–resin blends by scanning electron microscopy (SEM) corroborate well with the DMA and DSC results. From the DMA frequency sweep and temperature sweep studies, it is shown that the hydrocarbon resin tackifier acts as a diluent and causes a decrease in the storage modulus values (by reducing the entanglement and network density) in the rubbery plateau region. On the other hand, phenol formaldehyde resin behaves in the way similar to that of the reinforcing filler by increasing the storage modulus values (by increasing the entanglement and network density) in the rubbery plateau zone. The relaxation time estimated from the different zones of frequency sweep master curves provides information about the influence of the two tackifiers on the viscoelastic properties of the BIMS rubber in the respective zones. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Improved adhesion of EVAs with different vinyl acetate contents treated with sulphuric acid

Four ethylene vinyl acetate copolymers (EVAs) containing 9, 12, 18 and 20 wt% vinyl acetate (VA) were treated with concentrated sulphuric acid to improve their adhesion to polychloroprene (PCP) adhesive. The tensile strength and Young's modulus of EVAs decreased as the VA content increased, due to the reduction in crystallinity of the polyethylene blocks in the copolymer. The modifications produced in the EVAs by treatment with sulphuric acid were followed using contact angle measurements (water, 25 °C), ATR-IR spectroscopy and scanning electron microscopy (SEM). Adhesive-bond strength was obtained by T-peel tests on treated EVA/polychloroprene adhesive joints. The vinyl acetate content in the EVA affected the extent, but not the nature, of the surface modification produced by treatment with sulphuric acid. The treatment produced both sulfonation and oxidation on the EVA surfaces. The higher the vinyl acetate content in the EVA, the more significant the modifications produced. Increased T-peel strengths of EVA/polychloroprene adhesive + 5 wt% polyisocyanate joints were obtained and a mixed failure (adhesion failure + cohesive failure in the adhesive) was produced. It was found that, to be effective, the treatment of EVAs must be carried out with 96 wt% sulphuric acid.     

Influence of the Chemical Structure of Urethane-Based Thickeners on the Properties of Waterborne Polyurethane Adhesives

To analyse the parameters that influence the thickening mechanism of waterborne polyurethane adhesives, different hydrophobically modified ethoxylated polyurethane based thickeners (HEUR) were used. The thickeners were characterized by proton nuclear magnetic resonance (¹H-NMR) and gel permeation chromatography (GPC). The thickened adhesive solutions were characterized by flow rheology, pH, particle size measurements, solids content, and confocal microscopy. The thickened solid adhesive films were characterized by ATR-IR spectroscopy, parallel plate rheology, dynamic mechanical thermal analysis (DMTA), and differential scanning calorimetry (DSC). The adhesion was measured by a T-peel test of leather/polyurethane adhesive/SBR rubber joints. The addition of the different HEUR thickeners increased the viscosity of the polyurethane dispersion to different degrees. Furthermore, whereas the un-thickened polyurethane dispersion showed a Newtonian rheological behaviour, a shear-thinning rheological behaviour was observed in the thickened dispersions due to thickener-thickener and polyurethane-thickener interactions. The viscosity of the thickened polyurethane adhesive solutions increased with the degree of hydrophobicity and the molecular weight of the thickener. The addition of different thickeners increased the pH values due to the ionic adsorption, which is one of the interactions that contribute to the thickening mechanism of the polyurethane thickeners, besides hydrogen bonding and van der Waals hydrophobic interactions (micelles). The entanglement of the thickened polyurethane adhesives was studied by confocal microscopy. Although the addition of the thickeners did not affect the thermal properties of the polyurethanes, the T-peel strength of leather/adhesive/SBR rubber joints was influenced by the rheological properties of the thickened adhesives.     

Effect of N,N-dimethylacrylamide (DMA) on the comprehensive properties of acrylic latex pressure sensitive adhesives

Acrylic pressure sensitive adhesive (PSA) latexes were synthesized via a monomer-starved seeded semi-continuous emulsion polymerization process with butyl acrylate (BA), methyl methacrylate (MMA), N,N-dimethylacrylamide (DMA), acrylic acid (AA) and 2-hydroxyethyl acrylate (HEA) as monomers. Impacts of DMA on the resultant latex and PSA properties were comprehensively investigated. Results indicated that latex particle size was independent of the amount of DMA in the pre-emulsion feed with excessive and constant surfactant concentration. Latex viscosity increased with DMA concentration. It was also found that water resistance of acrylic latex PSA became worse by the presence of DMA, confirmed by water contact angle measurements. Besides, DSC results showed that as the amount of DMA increased, glass transition temperatures (T_g) of the polymers were elevated significantly. TGA results showed that thermal stability of PSA was improved with DMA as a co-monomer. Furthermore, as DMA amount increased, gel content slightly increased, while sol molecular weight (M_w, M_n) of the polymer decreased. Finally, with respect to the adhesive properties of the PSA, it was observed that loop tack initially increased and then decreased with the addition of DMA from 0 to 4 wt%, and the maximum value appeared at 1 wt%. Peel strength reduced, while shear strength improved with increased DMA concentration.     

Influence of molecular structure on the rheological and processing behavior of polyethylene resins

The rheological and processing behavior (melt fracture performance) of linear lowdensity polyethylenes (LLDPEs) is studied as a function of both the weight average molecular weight (M_w) and its distribution (MWD). A number of LLDPE resins having different molecular characteristics were tested, with essentially one characteristic (M_w or MWD) changing at a time. The first series of resins consisted of nine samples having a wide range of polydispersities (3.3–12.7) and nearly constant M_w and short chain branching. The second series had six resins with varying M_w (51,000–110,000) but fixed MWD (about 4). The influence of M_w and MWD on the viscosity profiles, linear viscoelastic moduli as expressed by means of a discrete spectrum of relaxation times, extrudate swell, and melt fracture behavior for these resins is reported. Correlations between the molecular characteristics of the resins and their rheological and processing behavior are also reported. It is found that for a given molecular weight, the optimum melt fracture performance is obtained at a specific polydispersity value, and it is characterized by a minimum relaxation time for the resin defined in terms of recoverable shear.