Kinetics of Cationic Photopolymerizations of UV‐Curable Epoxy‐Based SU8‐Negative Photoresists With and Without Silica Nanoparticles

Summary: This paper reports on the photocuring kinetics of protonic‐acid‐initiated cationic polymerizations of UV‐curable epoxy‐based SU8‐negative photoresist systems with and without silica nanoparticles, as assessed using photo‐DSC, FTIR spectroscopy, UV‐vis spectroscopy, and SEM. Photo‐DSC analysis using an autocatalytic kinetic model demonstrated that the cross‐link density and cure rate increased as the concentration of silica nanoparticles with surface silanol groups increased to 2.5 wt.‐%. This result was confirmed by FTIR spectroscopy, and suggests that the presence of silica nanoparticles of up to 2.5 wt.‐% promoted the cure conversion and cure rate of the UV‐curable hybrid organic/inorganic negative photoresists due to the synergistic effect of silica nanoparticles acting both as an effective flow or diffusion‐aid agent and as a proton‐donor cocatalyst during the cationic photopolymerization process. The decrease in the cross‐link density that occurred when the silica content was higher than 2.5 wt.‐% was attributed to aggregation between silica nanoparticles due to their high surface energy.

SEM photograph at the film‐air interface of the UV‐cured hybrid organic/inorganic photoresist containing 10 wt.‐% silica nanoparticles.     

Synthesis and Characterization of Segmented Block Copolymers Based on Hydroxyl‐Terminated Liquid Natural Rubber and α,ω‐Diisocyanato Telechelics

Summary: Segmented block copolymers, consisting of non‐polar soft segments from hydroxyl‐terminated liquid natural rubber (HTNR) and polar hard segments from α,ω‐diisocyanato telechelics obtained by “criss‐cross”‐cycloaddition, have been synthesized. The block copolymer formation took place under relatively mild reaction conditions at 80 °C in dichloroethane in the presence of dibutyltin dilaurate as a catalyst. The resulting block copolymers were characterized by spectroscopic techniques (¹H NMR, FTIR, UV‐vis spectroscopy) as well as GPC for molar mass determination. The block copolymers were compression molded in a hot stage press, and the resulting samples were characterized by DSC and stress‐strain measurement. The solubility and phase morphology of the materials have also been studied.

Segmented block copolymer from HTNR and α,ω‐diisocyanato telechelics     

Monomers for Adhesive Polymers 12 Synthesis and Free‐Radical Homo‐ and Copolymerization of 2‐Ethoxycarbonylallyl 5‐(1,2‐dithiolane‐3‐yl)‐pentanoate

The 2‐ethoxycarbonylallyl 5‐(1,2‐dithiolane‐3‐yl)‐pentanoate monomer (AODS) includes in its molecular structure C?C and S? S reactive bonds allowing it to behave as a bi‐functional monomer, possessing two groups, however, with different reactivity for use in polymer chain building. The polymerization‐specific features of this monomer are the absence of auto‐acceleration and polymer chain crosslinking. Polymerization proceeds readily through most free‐radical initiators. One exception, carboxy‐peroxides are rapidly decomposed without the production of free radicals. AODS is partially converted to a gel without the consumption of double bonds during monomer dissolution in certain organic solvents and after being mixed in solution with carboxy‐peroxides. The determined AODS‐co‐MMA copolymerization parameters are r₁ = 2.61, r₂ = 0.23 if Luperco peroxide is used as a polymerization initiator, and r₁ = 2.71, r₂ = 0.38 if AIBN is used.

     

Long‐Aliphatic‐Segment Polyamides: Salt Preparation and Subsequent Anhydrous Polymerization

Long‐aliphatic‐segment polyamides were prepared based on hexamethylenediamine and α,ω‐(CH₂)_x biosynthetic diacids (x = 10, 11, 12). The pertinent monomers (salts) were isolated as solids, thoroughly characterized for the first time, and then submitted to an anhydrous melt prepolymerization technique. The obtained prepolymers exhibited in the range of 5 100–11 800 g · mol^?1, and the molecular weight was further increased by up to 55% through solid‐state finishing. The suggested overall polyamidation cycle was conducted at short melt‐reaction times, so as to avoid any thermal degradation, and was proved efficient, indicating similar reactants polymerizability independently of the methylene content.

     

Synthesis and Characterization of Hyperbranched Poly(β‐ketoester) by the Michael Addition

Summary: A novel hyperbranched poly(β‐ketoester) was synthesized from 2‐(acetoacetoxy)ethyl acrylate by the Michael addition in the presence of 1,8‐diazabicyclo[5.4.0]undec‐7‐ene (DBU) as catalyst. ¹H NMR integration experiments revealed that the degree of branching in the poly(β‐ketoester) was remarkably high at a level of 82.9%. The number‐average molecular weight of the polymer was between 2 100 and 12 000 and increased with reaction temperature and conversion.

Synthesis of hyperbranched polymer by Michael addition of AAEA.     

Polybenzimidazolium‐Based Solid Electrolytes

A series of methyl, benzyl, and mixed polybenzimidazolium halides was synthesised and characterised by NMR spectroscopy. Membranes were formed and ion exchanged with hydroxides. These membranes are of interest for use in potentially platinum‐free anionic exchange membrane fuel cells. Crosslinked membranes were obtained by the addition of α,α′‐dibromo‐p‐xylene to the casting solution. The ion conductivity of membranes was determined by impedance spectroscopy. A hydroxide conductivity of 29 mS · cm^?1 at 26 °C and 58 mS · cm^?1 at 60 °C was obtained. The thermal and hydrolytic stability was investigated and a pathway for hydrolytic degradation proposed. Hydroxide ions react at the 2 position, the intermediate carbinol opens to the amine–amide, and further degrades under chain scission to diamine and carboxylic acid.

     

Elaboration of Poly(ε‐caprolactone)‐g‐TiNbO5 Nanocomposites via in situ Metal Complex Initiated Intercalative Polymerization

Summary: The preparation of poly(ε‐caprolactone)‐g‐TiNbO₅ nanocomposites via in situ intercalative polymerization of ε‐caprolactone initiated by an aluminium complex is described. These nanocomposites were obtained in the presence of HTiNbO₅ mineral pre‐treated by AlMe₃, but non‐modified by tetraalkylammonium cations. These hybrid materials obtained have been characterized by Fourier transform infrared absorption spectroscopy, wide‐angle X‐ray scattering, scanning electron microscopy, and dynamic mechanical analysis. Layered structure delamination and homogeneous distribution of mineral lamellae in the poly(ε‐caprolactone) (PCL) is figured out and strong improvement of the mechanical properties achieved. The storage modulus of the nanocomposites is enhanced as compared to pure PCL and increases monotonously with the amount of the filler in the range 3 to 10 wt.‐%.

SEM image of the fractured surface of a PCL‐TiNbO₅ nanocomposite film.     

Colloidal Crystalline Arrays of β‐Polymorphic Poly(vinylidene fluoride)

Stable layers of nearly monodisperse spheres of β‐polymorphic poly(vinylidene fluoride) with iridescent properties are prepared. The colloidal crystalline arrays (CCAs) were characterized by optical microscopy, differential scanning calorimetry (DSC), and FT‐IR spectroscopy. FT‐IR spectroscopic and wide‐angle X‐ray scattering (WAXS) studies revealed a β‐polymorphic PVF₂ structure, the DSC study showed that the level of crystallinity in the CCA was much higher than that in the melt‐crystallized sample, and UV‐visible spectroscopy showed extinction peaks at 323 and 510 nm in the CCAs. The β‐polymorphic PVF₂ structure, along with the optical extinction properties of these CCAs, raises the prospect of their application in optical filters and/or piezoelectric sensors.

Optical micrograph of PVF₂ CCA films cast on glass substrates.     

A New Heterogenization Technique for Single‐Site Polymerization Catalysts

Summary: Silica‐supported single‐site catalysts show limitations with respect to catalyst homogeneity and maximum metal content. A novel emulsion‐based catalyst heterogenization concept is described, which allows these limitations to be overcome. The method produces catalyst particles with an inherently perfect spherical shape and unique intra‐ and inter‐particle homogeneity. The catalyst particles are very compact and have a low surface area. Video microscopic studies confirm that the improved catalyst homogeneity leads to a more uniform polymerization behavior on a single particle level. The catalysts contain significantly more complex, compared to silica‐supported catalyst systems, which leads to correspondingly higher catalyst activities. No differences, in terms of the mass‐transfer kinetics of these low‐porosity catalysts, compared to porous catalyst systems have been observed.

Electron microscopy image of self‐supported single‐site catalyst prepared by the emulsion‐based method.     

Development and Characterization of Novel Biomimetic Composite Scaffolds Based on Bioglass‐Collagen‐Hyaluronic Acid‐Phosphatidylserine for Tissue Engineering Applications

Summary: Biomimetic scaffolds are appealing products for the repair of bone defects using tissue engineering strategies. The present study prepared novel biomimetic composite scaffolds with similar composite to natural bone using bioactive glass, collagen, hyaluronic acid, and phosphatidylserine. The microstructure, swelling ratio, biodegradability, and biomineralization characteristic of the composite scaffolds with and without hyaluronic acid and phosphatidylserine were compared and analyzed by SEM/EDAX, XRD, and FTIR techniques and in vitro test, and the properties can be influenced by 1‐ethyl‐3‐(3‐dimethylaminopropyl) carbodiimide (EDC)/N‐hydroxysuccinimide (NHS) crosslinking. The optimized properties of the crosslinked composite scaffolds observed in this study show the possibility of their use of bioactive and bioresorbable scaffolds in bone tissue engineering.

SEM micrographs of BG‐COL‐HYA‐PS composite scaffolds after immersion in SBF for 1 d.     

Synthesis of Poly(methyl‐co‐trifluoropropyl)silsesquioxanes and Their Thin Films for Low Dielectric Application

Poly(methyl‐co‐trifluoropropyl)silsesquioxanes (P(M‐co‐TFP)SSQs) were prepared using methyltrimethoxysilane (MTMS) and trifluoropropyltrimethoxysilane (TFPTMS). The molecular weight, microstructure of the copolymers and properties of their thin films have been changed by adjusting reaction parameters such as the molar ratio of water to silane, the molar ratio of catalyst to silane, reaction time, solvent content, and temperature. The refractive index of the copolymer thin film decreased from 1.404 to ca. 1.348 as curing temperature was increased to 420 °C. The dielectric constant of the film decreased with an increase of the molecular weight of the copolymer, and the lowest dielectric constant obtained was ca. 2.2. Hardness and elastic modulus of the thin films were 0.7 and 5 GPa, respectively. Crack velocity was measured to be 10^?11 m/s at the film thickness of around 0.9 μm under aqueous environment.

     

A Novel N‐Succinylchitosan‐graft‐Polyacrylamide/Attapulgite Composite Hydrogel Prepared through Inverse Suspension Polymerization

A novel N‐succinylchitosan‐graft‐polyacrylamide/attapulgite composite hydrogel was prepared by using N‐succinylchitosan, acrylamide and attapulgite through inverse suspension polymerization. The result from FTIR spectra showed that ? OH of attapulgite, ? OH and ? NHCO of N‐succinylchitosan participated in graft polymerization with acrylamide. The introduced attapulgite could enhance thermal stability of the hydrogel. Scanning electron microscopy observation indicates that the composite hydrogel has a microporous surface. The volume ratio of heptane to water, weight ratio of acrylamide to N‐succinylchitosan and attapulgite content have great influence on swelling ability of the composite hydrogel. The composite hydrogel shows higher swelling rate and pH‐sensitivity compared to that of without attapulgite.

     

Nucleation Effect of Layered Metal Phosphonate on Crystallization of Bacterial Poly[(3‐hydroxybutyrate)‐co‐(3‐hydroxyhexanoate)]

The nucleating effect of zinc phenylphosphonate (PPZn) was investigated on the as‐bacterially synthesized poly(3‐hydroxybutyrate) [P(3HB)] and poly[(3‐hydroxybutyrate)‐co‐(3‐hydroxyhexanoate)]s [P(3HB‐co‐3HHx)s] in order to improve their crystallization rate. PPZn is found an efficient nucleating agent on the crystallization of P(3HB) and P(3HB‐co‐3HHx) with low 3HHx unit content. The nucleation mechanism is proposed to be epitaxial nucleation. Both the comonomer‐unit composition and its distribution of P(3HB‐co‐3HHx)s were found exhibiting significant effect on the nucleating effect of PPZn. It is found that PPZn is more efficient on nucleating the crystallization of P(3HB‐co‐3HHx) with a broader comonomer‐unit compositional distribution than that with a narrower distribution.

     

All‐Solid Actuator Consisting of Polyaniline Film and Solid Polymer Electrolyte

An all‐solid actuator, consisting of a polyaniline (PANI) film and a solid polymer electrolyte (SPE) of poly(ethylene oxide) derivative (STO288), clearly showed a reversible displacement in an atmosphere when a voltage was applied between the PANI film and the SPE layer. The displacement and the response rate are mainly dependent on the applied voltage and the employed supporting salt, but are influenced by the humidity and temperature of the environment. The results of the present experiments have revealed that the influences of the humidity and temperature on the performance of the actuator are predominantly through the ionic conductivity of the SPE.

All‐solid actuator consisting of PANI and SPE.     

Segmented Block Copolymers with Monodisperse Hard Segments: The Influence of H‐Bonding on Various Properties

The properties of segmented‐copolymer‐based H‐bonding and non‐H‐bonding crystallisable segments and poly(tetramethylene oxide) segments were studied. The crystallisable segments were monodisperse in length and the non‐hydrogen‐bonding segments were made of tetraamidepiperazineterephthalamide (TPTPT). The polymers were characterised by DSC, FT‐IR, SAXS and DMTA. The mechanical properties were studied by tensile, compression set and tensile set measurements. The TPTPT segmented copolymers displayed low glass transition temperatures (T_g, ?70 °C), good low‐temperature properties, moderate moduli (G′ ≈ 10–33 MPa) and high melting temperatures (185–220 °C). However, as compared to H‐bonded segments, both the modulus and the yield stress were relatively low.

     

Silicone Liner‐Free Pressure‐Sensitive Adhesive Labels

Pressure‐sensitive adhesives (PSA) were microencapsulated using simple and complex coacervation and aminoplaste. The microcapsules thus prepared were characterized by FTIR spectroscopy, particle size distribution, rheological behavior, and peeling tests. The microcapsules were isolated and found to be out of sticky indicating that the PSAs were indeed encapsulated. The prepared suspensions were deposited at the surface of a paper sheets and the dried labels were then pressed against each other. The ensuing complex was then characterized in terms of peeling forces and showed that the encapsulation using aminoplaste technique of a commercial PSA yielded peel energy of 170 J · m^?2, which constitutes the recovering of about 68% of the adhesive power of the original nonencapsulated PSA.

     

Novel Poly(N‐isopropylacrylamide)‐graft‐poly(vinylidene fluoride) Copolymers for Temperature‐Sensitive Microfiltration Membranes

In the present work, we report on the synthesis and characterization of poly(vinylidene fluoride) (PVDF) with N‐isopropylacrylamide (NIPAAM) polymer side chains from molecular graft copolymerization in solution. The copolymer can be readily cast into temperature‐sensitive microfiltration (MF) membranes by the phase inversion technique. The copolymer approach to membrane fabrication allows a much better control of the physicochemical nature of the membrane pores through the variation in graft concentration, membrane casting temperature and concentration of the membrane casting solution.

     

Temperature Sensitive Behavior of Poly(N‐isopropylacrylamide) Grafted Onto Electron Beam‐Irradiated Poly(propylene)

Summary: N‐Isopropylacrylamide (NIPAAm) was graft‐polymerized from its acetone solution onto poly(propylene) (PP) films, after electron‐beam irradiation in the presence of air oxygen. The effects of pre‐irradiation dose as well as monomer concentration, reaction temperature and reaction time on the grafting efficiency were investigated. Typical conditions for achieving maximum grafting yield were observed for 1 M monomer concentration, after PP pre‐irradiation with a 300 kGy dose and a reaction temperature of 50 °C. The location of the graft polymerization was examined by different methods including measurements of dimensional variations, calorimetry, SEM and AFM. The temperature‐responsive behavior of grafted copolymer was studied by swelling and contact angle measurements at different temperatures.

Temperature dependence of the swelling ratio in water as a function of temperature.     

Effects of Temperature and Surfactants on the Equilibrium Swelling Behavior of Poly[acrylamide‐co‐(itaconic acid)] Hydrogels

Summary: The swelling equilibrium of poly(acrylamide) [PAAm] and poly[acrylamide‐co‐(itaconic acid)] [P(AAm/IA)] hydrogels was studied as a function of temperature and IA content in aqueous solutions of surfactants: sodium dodecyl sulfate (SDS, anionic) and hexadecyltrimethylammonium bromide (HTAB, cationic). P(AAm/IA) hydrogels in water exhibited reentrant conformational transitions depending on temperature, whereas PAAm hydrogels were not affected with the change of temperature. The equilibrium‐volume‐swelling ratio of P(AAm/IA) hydrogels increased sharply in SDS solutions, with an increase of the mole percent of IA. However, in HTAB solution, the equilibrium‐volume‐swelling ratio of these hydrogels decreased with an increase of IA content.

The equilibrium volume‐swelling ratios of the hydrogels in water shown as a function of temperature.     

Bio‐Based Rubbers by Concurrent Cationic and Ring‐Opening Metathesis Polymerization of a Modified Linseed Oil

Bio‐based rubbers prepared by tandem cationic polymerization and ROMP using a norbornenyl‐modified linseed oil, Dilulin?, and a norbornene diester, NBDC, have been prepared and characterized. Increasing the concentration of the NBDC in the mixture results in a decrease in the glass transition temperature. The new bio‐based rubbers exhibit tensile test behavior ranging from relatively brittle (18% elongation) to moderately flexible (52% elongation) and with decreasing values of tensile stress with increasing NBDC content. Thermogravimetric analysis reveals that the bio‐based rubbers have maximum decomposition temperatures of over 450 °C with their thermal stability decreasing with increasing loadings of NBDC.