Poly[(N‐isopropylacrylamide)‐co‐(itaconic acid)] hydrogels with poly(ethylene glycol)

The aim of the work reported here was to investigate temperature‐ and pH‐sensitive hydrogels of N‐isopropylacrylamide (NIPAM) and itaconic acid (IA) and their semi‐interpenetrating polymer networks (semi‐IPNs) with varying contents of poly(ethylene glycol) (PEG). The stimuli responsiveness, swelling behaviour and mechanical properties of the hydrogels and semi‐IPNs were studied in order to investigate the effect of various amounts of PEG. Pulsed‐gradient spin‐echo NMR experiments were carried out to investigate the diffusion process. The pH sensitivity increased with an increasing amount of PEG in the semi‐IPNs, while the overall rate of water uptake was diffusion‐controlled (n < 0.5). For certain PEG contents (5 and 10 wt%), the semi‐IPNs exhibited better mechanical properties than the poly(NIPAM‐co‐IA) copolymer. The calculated values of the self‐diffusion coefficients of water indicated facilitated diffusion of water through the system with increased amounts of PEG, while the self‐diffusion coefficients of a model compound, metoprolol tartrate, showed no significant dependence on the amount of PEG. According to the results obtained and compared to results reported in the literature, the investigated semi‐IPNs may have potential applications in the controlled release of macromolecular active agents such as proteins and peptides. Copyright © 2009 Society of Chemical Industry     

Effects of Temperature and Surfactants on the Equilibrium Swelling Behavior of Poly[acrylamide‐co‐(itaconic acid)] Hydrogels

Summary: The swelling equilibrium of poly(acrylamide) [PAAm] and poly[acrylamide‐co‐(itaconic acid)] [P(AAm/IA)] hydrogels was studied as a function of temperature and IA content in aqueous solutions of surfactants: sodium dodecyl sulfate (SDS, anionic) and hexadecyltrimethylammonium bromide (HTAB, cationic). P(AAm/IA) hydrogels in water exhibited reentrant conformational transitions depending on temperature, whereas PAAm hydrogels were not affected with the change of temperature. The equilibrium‐volume‐swelling ratio of P(AAm/IA) hydrogels increased sharply in SDS solutions, with an increase of the mole percent of IA. However, in HTAB solution, the equilibrium‐volume‐swelling ratio of these hydrogels decreased with an increase of IA content.

The equilibrium volume‐swelling ratios of the hydrogels in water shown as a function of temperature.     

Swelling and Adsorption Properties of Hydrophobic Poly[(N‐(3‐(dimethylamino)propyl)methacrylamide)‐co‐(lauryl acrylate)] Hydrogels in Aqueous Solutions of Surfactants

Summary: The swelling and adsorption behavior of a series of hydrophobic poly[(N‐(3‐(dimethylamino)propyl)methacrylamide)‐co‐(lauryl acrylate)] [P(DMAPMA‐co‐LA)] hydrogels was studied as a function of temperature in aqueous solutions of the anionic surfactant sodium dodecyl sulfate (SDS) and the cationic surfactant dodecyltrimethylammonium bromide (DTAB). Between 0 and 41.7 mol‐% of lauryl acrylate (LA) were used as a hydrophobic comonomer in the hydrogel synthesis. In SDS solutions, the equilibrium swelling ratio of the hydrogels decreased with increasing temperature. At SDS concentrations below 0.0083 M , the hydrogels exhibited an almost linear swelling behavior. However, for SDS concentrations above 0.0083 M , non‐linear swelling behavior was observed in the range 28–36 °C. In contrast to the SDS solutions, in all DTAB solutions the equilibrium swelling ratio of the hydrogels increased with increasing temperature and a positive temperature sensitive property was shown for all P(DMAPMA‐co‐LA) hydrogels. The adsorption capacities of the hydrogels in aqueous solutions of SDS and DTAB were determined via surface tension measurements. An increase in the LA content in the hydrogel caused an increase in the amount of adsorbed surfactant molecules in both media.

Effect of the DTAB concentration on the adsorption capacities of P(DMAPMA‐co‐LA) hydrogels.     

Determination of swelling behavior and morphological properties of poly(acrylamide‐co‐itaconic acid) and poly(acrylic acid‐co‐itaconic acid) copolymeric hydrogels

Poly(acrylamide‐co‐itaconic acid) (PAAmIA) and poly(acrylic acid‐co‐itaconic acid) (PAAIA) copolymeric hydrogels were prepared with different compositions via free‐radical polymerization. Ethylene glycol dimethacrylate (EGDMA) was used as an original crosslinker for these monomers. Gelation percentages of the monomers were studied in detail and it was found that addition of IA into the monomer mixture decreased the gelation percentage. The variation in swelling values (%) with time, temperature, and pH was determined for all hydrogels. PAA, which is the most swollen hydrogel, has the swelling percentage value of 2000% at pH = 7.4, 37°C. Swelling behaviors were explained with detailed SEM micrographs, which show the morphologic differences between dry and swollen hydrogels. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5994–5999, 2006     

Swelling and elasticity of poly (N‐isopropylacrylamide‐co‐4‐vinyl benzene sulfonic acid sodium salt) hydrogels

The mechanical properties and the swelling behavior of hydrogels based on N‐isopropylacrylamide (NIPA) and 4‐vinylbenzenesulfonic acid sodium salt (styrene sulfonate, SSA) monomers were investigated. The mole fraction of SSA in the comonomer feed varied between 0 and 1, whereas the crosslinker ratio was fixed at 1/85. Both the swelling and the elasticity data of the hydrogels swollen in water show that they are in the non‐Gaussian regime. The exponents found for the charge density dependence of the equilibrium swelling ratio as well as for the volume dependence of the gel elastic modulus are in good agreement with the predicted course of the non‐Gaussian elasticity of swollen hydrogels. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 135–141, 2004     

External Stimuli‐Responsive Characteristics of Ionic Poly[(N,N‐diethylaminoethyl methacrylate)‐co‐(N‐vinyl‐2‐pyrrolidone)] Hydrogels

Summary: Polyelectrolyte hydrogels containing diprotic acid moieties sensitive to ionic strength changes of the swelling medium were synthesized from N,N‐diethylaminoethyl methacrylate (DEAEMA), N‐vinyl‐2‐pyrrolidone (VP) and itaconic acid (IA) by using ammonium persulfate (APS) as a free radical initiator in the presence of the cross‐linker, methylenebisacrylamide (MBAAm). The swelling behavior of the ionic poly[(N,N‐diethylaminoethyl methacrylate)‐co‐(N‐vinyl‐2‐pyrrolidone)] [P(DEAEMA/VP)] hydrogels were investigated in pure water; in NaCI solutions with pH 4 and 9; and in water‐acetone mixtures depending on the IA content in the hydrogel. The average molecular mass between cross‐links ( ) and polymer‐solvent interaction parameter (χ) of the hydrogels were determined from equilibrium swelling values. The pulsatile swelling behavior was also observed in response to solvent changes between the solution in water and in acetone. The equilibrium swelling ratio of these hydrogels was basically unaffected with change in temperature. The swelling variations were explained according to the swelling theory based on the hydrogel chemical structure.

Pulsatile swelling behavior of ionic P(DEAEMA/VP) hydrogels in response to solvent changes between water and acetone at 25 °C.     

Synthesis and characterization of cassava starch graft poly(acrylic acid) and poly[(acrylic acid)‐co‐acrylamide] and polymer flocculants for wastewater treatment

Starch‐g‐poly(acrylic acid) and poly[(acrylic acid)‐co‐acrylamide] synthesized via chemically crosslinking polymerization were then each mixed with inorganic coagulants of aluminum sulfate hydrate [Al₂(SO₄)₃·18H₂O], calcium hydroxide [Ca(OH)₂], and ferric sulfate [Fe₂(SO₄)₃] in a proper ratio to form complex polymeric flocculants (CPFs). All CPFs exhibited low water absorbency than those of the uncomplexed superabsorbent copolymers. The color reduction by the CPFs was tested with both synthetic wastewater and selected wastewater samples from textile industries. The synthetic wastewater was prepared from a direct dye in a concentration of 50 mg dm^?3 at pH 7. The CPFs of poly[(acrylic acid)‐co‐acrylamide] with calcium hydroxide at a ratio of 1:2 is the most effective CPF for the wastewater color reduction. The CPF concentration of 500 mg dm^?3 could reduce the color of the synthetic wastewater containing the direct dye solution by 95.4% and that of the industrial wastewater by 76%. Starch‐g‐poly(acrylic acid)/Ca(OH)₂ CPF can reduce the synthetic direct dye and the industrial wastewater by 74% and 18%, respectively. Chemical oxygen demand, residual metal ion concentrations, pHs, turbidity of the wastewater were also investigated and the potential use of the complex polymer flocculants for textile wastewater treatment was indicated. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 2915–2928, 2006     

Mechanical properties of poly(N‐isopropyl‐acrylamide‐co‐itaconic acid) hydrogels

Hydrogels of N‐isopropylacrylamide and itaconic acid were synthesized with different monomer ratios and with two crosslinking agent concentrations. The different xerogels were immersed in water and the swelling process was conducted up to equilibrium conditions at two temperatures (22 and 37°C). These temperatures are lower and higher than the transition temperature shown by PNIPA hydrogels. The mechanical properties of the different solvated hydrogels were examined by oscillatory shear measurements at 22 and 37°C. The copolymer volume fraction and the elastic storage modulus of the hydrogels decreased as the itaconic acid percentage in the copolymer increased. This behavior was attributed to the higher hydrophilic character of the itaconic acid comonomer. Effective crosslinking density, molar mass between crosslinks, and the polymer–solvent interaction parameter were determined from the experimental values of the elastic storage moduli and the copolymer volume fractions. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2540–2545, 2002     

聚乙烯醇/膨润土杂化水凝胶的力学性能和溶胀行为

利用冷冻-解冻法制备了聚乙烯醇/膨润土杂化水凝胶. X射线衍射结果表明,膨润土以剥离形式分布在水凝胶基体中. 研究结果表明,与纯PVA5水凝胶相比,经过5个冷冻-解冻循环制备的含2%(w)膨润土的杂化水凝胶的拉伸模量、拉伸强度和断裂伸长率分别增加了44.0%, 74.2%和25.2%,而溶胀行为与5个循环的纯水凝胶相近. 含0.5%(w)膨润土的杂化水凝胶的拉伸模量和拉伸强度高于基体水凝胶,其在溶胀400 min时的溶胀度高于所有的样品.     

Poly(methacrylamide‐co‐acrylic acid) hydrogels for gastrointestinal delivery of theophylline. I. Swelling characterization

pH sensitive copolymeric hydrogels have been synthesized by free‐radical polymerization of methacrylamide and acrylic acid in aqueous medium. The gels were characterized by FTIR spectroscopy, thermogravimetric analysis, and swelling measurements. To determine the suitability of theses hydrogels for gastrointestinal oral delivery of model drug theophylline, their swelling behavior was investigated as a function of pH and various structural parameters such as the average molecular weight between crosslinks, crosslink density, and mesh size were calculated. Likewise initial, average and late time diffusion coefficients were also evaluated in simulating intestinal fluid of pH 6.8 at 37°C. The gel underwent sharp volume phase transition in the vicinity of pH 5.8. The mesh sizes of the hydrogel were between 8.4 and 9.2 Å in the collapsed state (pH range 1–2; SGF) and between 514 and 524 Å in the swollen state (pH range 7–8; SIF). The experimental data was found to fit well to Beren‐Hopfenberg equation thus suggesting that later part of swelling was chain relaxation controlled. The activation energy, as determined from Arrhenius equation was found to be 13.71 kJ mol^?1. Likewise, enthalpy of mixing was also evaluated using Gibbs‐Helmholtz equation. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2995–3008, 2006     

Dynamic Mechanical Properties of Poly(propylene) Blends with Poly[ethylene‐co‐(methyl acrylate)]

Summary: Blends of poly(propylene) (PP) were prepared with poly[ethylene‐co‐(methyl acrylate)] (EMA) having 9.0 and 21.5% methyl acrylate comonomer. A similar series of blends were compatibilized by using maleic anhydride grafted PP. The morphology and mechanical properties of the blends were investigated using differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA) in tensile mode. The DMA method and conditions were optimized for polymer film specimens and are discussed in the experimental section. The DSC results showed separate melting that is indicative of phase‐separated blends, analogous to other PP‐polyethylene blends but with the added polarity of methyl acrylate pendant side groups that may be beneficial for chemical resistance. Heterogeneous nucleation of PP was decreased in the blends because of migration of nuclei into the more polar EMA phase. The crystallinity and peak‐melting temperature did not vary significantly, although the width of the melting endotherm increased in the blends indicating a change had occurred to the crystals. DMA analysis showed the crystal‐crystal slip transition and glass transition (T_g) for PP as well as a T_g of the EMA copolymer occurring chronologically toward lower temperatures. The storage modulus of PP and the blends was generally greater with annealing at 150 °C compared with isothermal crystallization at 130 °C. The storage modulus of the blends for isothermally crystallized PP increased with 5% EMA, then decreased for higher amounts of EMA. Annealing caused a decrease with increasing copolymer content. The extent of the trend was greater for the compatibilized blends. The T_g of the blends varied over a small range, although this change was less for the compatibilized blends.

Storage modulus for PP and EMA9.0 blends annealed at 150 °C.     

Swelling behavior of poly(MMA‐co‐BA‐co‐PPGDA) polymers

The kinetics of emulsion polymerization of monomers MMA/BA was studied to investigate the effect of cross‐linkable monomer PPGDA. The results showed that by the incorporation of PPGDA, rate constant of reaction decreased. The IR and differential scanning calorimetry were used to characterize the presence of PPGDA in the synthesized polymers. These polymers were coated on glass panels and cured at appropriate temperature. The results showed that the polymer containing 15 wt % PPGDA had minimum value of Fickian diffusion coefficient, thus showing highest level of cross‐linking among all the polymers studied. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Hydrolyzed collagen‐grafted‐poly[(acrylic acid)‐co‐(methacrylic acid)] hydrogel for drug delivery

Hydrolyzed collagen‐grafted‐poly[(acrylic acid)‐co‐(methacrylic acid)] hydrogels were synthesized by solution polymerization and confirmed by infrared spectroscopy. From sequential univariate analysis, the optimal molar ratio of acrylic acid: methacrylic acid was 92:8 in the presence of N,N′‐methylenebisacrylamide, ammonium persulfate, and N,N,N′,N′‐tetramethylethylenediamine at 0.12, 0.015, and 0.2% mol of the monomers, respectively. The water absorbency of this hydrogel was both pH‐ and temperature‐dependent, but was higher in nonbuffered water than in boric acid/citric acid/phosphate buffer under the same conditions. The optimal hydrogel could swiftly swell and deswell in neutral and acid solutions, respectively. Its potential application in drug delivery was examined using insulin and methylene blue as model payload drugs. Loading in a 50% (v v^?1) ethanol solution gave a higher insulin loading level than in the buffer water. Insulin and methylene blue were both released at pH 6.8 but not at pH 1.2, but followed first order kinetics and the Higuchi equation, respectively. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45654.     

Investigation of thermal behavior of poly(2‐hydroxyethyl methacrylate‐co‐itaconic acid) networks

The thermal behavior of poly(2‐hydroxyethyl methacrylate) [PHEMA] homopolymer and poly(2‐hydroxyethyl methacrylate‐co‐itaconic acid) [P(HEMA/IA)] copolymeric networks synthesized using a radiation‐induced polymerization technique was investigated by differential scanning calorimetry, thermogravimetric analysis, and Fourier transform infrared spectroscopy. The glass‐transition temperature (T_g) of the PHEMA homopolymer was found to be 87°C. On the other hand, the T_g of the P(HEMA/IA) networks increased from 88°C to 117°C with an increasing amount of IA in the network system. The thermal degradation reaction mechanism of the P(HEMA/IA) networks was determined to be different from the PHEMA homopolymer, as confirmed by thermogravimetric analysis. It was observed that the initial thermal degradation temperature of these copolymeric networks increased from 271°C to 300°C with IA content. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1602–1607, 2007     

Poly(N‐isopropylacrylamide‐co‐poly(ethylene glycol))‐acrylate simultaneously physically and chemically gelling polymer systems

In an effort to create an in situ physically and chemically cross‐linked hydrogel for in vivo applications, N‐isopropylacrylamide (NIPAAm) was copolymerized with poly(ethylene glycol)‐monoacrylate (PEG‐monoacrylate) and then the hydroxyl terminus of the PEG was further modified with acryloyl chloride to form poly(NIPAAm‐co‐PEG) with acrylate terminated pendant groups. In addition to physically gelling with temperature changes, when mixed with a multi‐thiol compound such as pentaerythritol tetrakis 3‐mercaptopropionate (QT) in phosphate buffer saline solution of pH 7.4, this polymer formed a chemical gel via a Michael‐type addition reaction. The chemical gelation time of the polymer was affected by mixing time; swelling of the copolymer solutions was temperature dependant. Because of its unique gelation properties, this material may be better suited for long‐term functional replacement applications than other thermo‐sensitive physical gels. Also, the PEG content of this material may render it more biocompatible than similar HEMA‐based precursors in previous simultaneous chemically and physically gelling materials. With its improved mechanical strength and biocompatibility, this material could potentially be applied as a thermally gelling injectable biomaterial for aneurysm or arteriovenous malformation (AVM) occlusion. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Preparation and Swelling Behavior of Fast‐Swelling Superabsorbent Hydrogels Based On Starch‐g‐Poly(acrylic acid‐co‐sodium acrylate)

Summary: A novel fast‐swelling porous superabsorbent hydrogel was prepared by grafting acrylic acid onto corn starch through free‐radical polymerization in aqueous solution using N,N′‐methylenebisacrylamide as a crosslinker, ammonium persulfate as an initiator, sodium dodecyl sulfate and p‐octyl poly(ethylene glycol)phenyl ether as pore‐forming agents. The graft polymerization and surface morphology of the porous superabsorbents were characterized by FTIR and SEM. The results indicate that the porous superabsorbents were endowed with higher equilibrium water absorbency and faster swelling rate (they needed only 10 min to reach 90% of their equilibrium water absorbency) compared with the nonporous superabsorbents. The dewatering method employed had a significant influence on the swelling behavior of the superabsorbents and dewatering agents were useful to preserve the pores formed during the polymerization process.

The equilibrium water absorbency in distilled water, for the porous and non‐porous starch‐g‐poly(acrylic acid‐co‐sodium acrylate) superabsorbent hydrogels dried through different procedures.     

Preparation and Swelling Properties of Temperature‐Sensitive Semi‐Interpenetrating Polymer Networks Composed of Poly[(N‐tert‐butylacrylamide)‐co‐acrylamide] and Hydroxypropyl Cellulose

Summary: Temperature‐responsive hydrogels based on linear HPC and crosslinked P(NTBA‐co‐AAm) were prepared by the semi‐IPN technique. The structure of these semi‐IPN hydrogels was investigated by FT‐IR spectroscopy. An increase in normalized band ratios (A₂₉₈₀/A₁₆₆₅) was observed with increasing HPC content in the initial mixture. The swelling kinetics and water transport mechanism of these semi‐IPN hydrogels were examined and their temperature responsive behaviors were also investigated by measuring equilibrium swelling ratios and pulsatile swelling experiments. The results showed that these semi‐IPN hydrogels underwent a volume phase transition between 18 and 22 °C irrespective of the amounts of MBAAm and HPC. However, below the volume phase transition temperature, their equilibrium swelling ratios were affected by the amount of MBAAm and HPC. The pulsatile swelling experiments indicated that the lower the MBAAm and the higher HPC contents in semi‐IPN hydrogels the faster the response rate temperature change.

Equilibrium swelling ratios of the semi‐IPN P(NTBA‐co‐AAm)/HPC hydrogels in water shown as a function of temperature.     

Synthesis and reactive features of a terpolymer: Poly(N‐vinyl‐2‐pyrrolidone‐co‐vinyl acetate‐co‐glycidyl methacrylate)

A polyvinyl pyrrolidone terpolymer system is described that can be chemically cross‐linked at moderate, 70–100°C, temperatures. The system has significant potential for development of durable long‐lasting pyrrolidone coatings in a wide range of applications, particularly in water filtration membrane construction where leaching is an unresolved, serious problem. The synthesis of the terpolymer, poly(N‐vinyl‐2‐pyrrolidone‐co‐vinyl acetate‐co‐glycidyl methacrylate), by free radical polymerization is described. The reactive features of this terpolymer are presented in the context of acidic anhydride curing. In a polar aprotic solvent, the terpolymer is reacted with poly(methyl vinyl ether‐co‐maleic acid) and cured thermally. Key aspects of the terpolymer synthesis and the acid anhydride cross‐linking reaction using DSC, rheology, FTIR, and a small molecule model system to study the cross‐linking chemistry are presented. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Hydrogel of Radiation‐Induced Cross‐Linked Hydroxypropylcellulose

Hydroxypropylcellulose (HPC) hydrogel being a material of natural origin, combines the properties of a polymer, which make up the network, with biodegradability. In this report the effects of high energy radiation on the ether of cellulose‐HPC are presented. The polymer irradiated in its solid state or in dilute aqueous solution underwent mainly degradation, induced by the cleavage of glycosidic bonds in its main chain. Irradiation of HPC in aqueous solutions at moderate concentrations resulted in the formation of hydrogels. Chemical cross‐links bond the chains of polymer, turning it to an insoluble macroscopic gel. We have found that in addition to concentration, dosage and dose rate can affect the results of irradiation. Electron beam irradiation gave higher gel fraction, up to 90%, than gamma irradiation, which has a maximum gel fraction of 65%. Swelling of the cross‐linked hydrogels was related to the density of cross‐links and was the highest at low irradiation doses. HPC hydrogels displayed thermally reversible character in their swelling. The volume of gel underwent continuous deswelling with an increase of the solution temperature, with the deswelling rate increasing rapidly over 40°C. At elevated temperatures the hydrogel collapsed, lost its transparency and changed color to translucent white. This transition was fully reversible when the gel was placed in the medium of low temperature. The hydrogel demonstrated superior mechanical properties. Despite of the stable three‐dimensional cross‐linked network, the gels underwent biodegradation under controlled conditions when enzyme was used.     

Crosslinking of poly[(3‐hydroxybutyrate)‐co‐(3‐hydroxyvalerate)] using dicumyl peroxide as initiator

In order to modify poly [(3‐hydroxybutyrate)‐co‐(3‐hydroxyvalerate)] (PHBV), the crosslinking of this copolymer was carried out at 160 °C using dicumyl peroxide (DCP) as the initiator. The torque of the PHBV melt showed an abrupt upturn when DCP was added. Appropriate values for the gel fraction and crosslink density were obtained when the DCP content was up to 1 wt% of the PHBV. According to the NMR spectroscopic data, the location of the free radical reaction was determined to be at the tertiary carbons in the PHBV chains. The melting point, crystallization temperature and crystallinity of PHBV decreased significantly with increasing DCP content. The effect of crosslinking on the melt viscosity of PHBV was confirmed as being positive. Moreover, the mechanical properties of PHBV were improved by curing with DCP. When 1 wt% DCP was used, the ultimate elongation of PHBV increased from 4 to 11 %. A preliminary biodegradation study confirmed the total biodegradability of crosslinked PHBV. Copyright © 2004 Society of Chemical Industry