Influence of ZnO content and annealing temperature on the dielectric properties of ZnO/Al2O3 composite coatings

ZnO/Al₂O₃ coatings were prepared by atmospheric plasma spraying (APS) using ZnO powders and Al₂O₃ powders as starting materials. The dielectric properties of these coatings were discussed. Both the real part of permittivity and the energy loss increase greatly with increasing ZnO content over the frequency range 8.2-12.4 GHz, which can be ascribed to orientation polarization and relaxation polarization due to a higher ZnO content. The frequency-dependent maximum of the loss tangent is found to obey Debye theory. In addition, annealing temperature which leads to the change of ZnO content also plays an important role in the dielectric performance.     

Al2O3-ZrO2 mixed oxide composite incorporated aluminium rich zinc coatings for high wear resistance

Corrosion resistance and wear resistance are the two important parameters for high performance of zinc galvanic coating. In the present work, the improvement of these two characteristics was achieved by the incorporation of Al₂O₃-ZrO₂ mixed oxide composite in the coating. Al₂O₃-ZrO₂ mixed oxide composite was synthesized from ZrOCl₂·8H₂O. Aluminium rich zinc coatings with high sliding wear resistance was developed from a galvanic bath containing the mixed oxide. Based on the performance of the coating during physicochemical and electrochemical characterization, the concentration of mixed oxide composite in the bath was optimized as 0.50 wt% Al₂O₃-0.50 wt% ZrO₂. While rich in Al-metal content in the coating caused high corrosion resistance, the incorporation of the mixed oxide improved structural characteristics of the coating resulting in high wear resistance also. The coating was nonporous in nature and even the interior layers had high stability. The coatings have potential scope for high industrial utility.     

Morphology and preferred orientation of Y2O3 film prepared by high-speed laser CVD

Yttria (Y₂O₃) films were prepared at high deposition rates of up to 83 nm/s (300 μm/h) by laser chemical vapor deposition (LCVD) using an Y(dpm)₃ precursor. The effects of deposition conditions, mainly total gas pressure and laser power, on morphology, deposition rate and preferred orientation were studied. Plasma was produced around the substrate over a critical laser power resulting in significant increases in deposition temperature and deposition rate. The high deposition rate (300 μm/h) by LCVD was about 100 to 1000 times as high as those by conventional CVD. The morphology of Y₂O₃ films changed from faceted and columnar structures with high (400) orientation to a columnar structure with high (440) orientation, and finally to a cone-like structure with moderate (440) orientation with increasing total gas pressure (P_tot).     

Preparation of Al2O3/DLC/Au/MoS2 chameleon coatings for space and ambient environments

We have investigated the tribological properties of nanocomposite “chameleon” coatings, which adapt their low friction behavior with the surrounding environmental humidity and temperature. The material system of interest included alumina (Al₂O₃) in an Au matrix with diamond-like carbon (DLC) and MoS₂ nanoparticle inclusions. The coating design included formation of nanocrystalline hard oxide particles for wear resistance, embedding them into an amorphous matrix for toughness enhancement, and inclusion of nanocrystalline and/or amorphous solid lubricants for friction adaptation to different environments.Chemical analysis was used to ascertain a correlation between chemical bonding of species and frictional properties. Friction measurements were studied in cycling between humid air and dry nitrogen conditions at room temperature and during heating in air to 500 °C. It was observed that both graphitic carbon and MoS₂ worked together to give low friction in variable humidity environment, while Au was valuable for a low friction at elevated temperatures. Friction coefficients were found to be 0.02-0.03 in dry nitrogen, 0.1-0.15 in humid air, and 0.1 in air at 500 °C. Thus the tribological property results have shown that the system provides “chameleon” type adaptation behavior in different environments relevant for aerospace systems.     

Microstructure and tribological behavior of suspension plasma sprayed Al2O3 and Al2O3-YSZ composite coatings

Several alumina and alumina-zirconia composite coatings were manufactured by suspension plasma spraying (SPS), implementing different operating conditions in order to achieve dense and cohesive structures. Temperatures and velocities of the in flight particles were measured with a commercial diagnostic system (Accuraspray®) at the spray distance as a function of the plasma operating parameters. Temperatures around 2000 °C and velocities as high as 450 m/s were detected. Hence, coatings with high amount of α-alumina phase were produced. The microstructure evolution according to the spray parameters was studied as well as the final tribological properties showing efficient wear resistance.     

Effect of the suspension composition on the microstructural properties of high velocity suspension flame sprayed (HVSFS) Al2O3 coatings

Seven different Al₂O₃-based suspensions were prepared by dispersing two nano-sized Al₂O₃ powders (having analogous size distribution and chemical composition but different surface chemistry), one micron-sized powder and their mixtures in a water + isopropanol solution. High velocity suspension flame sprayed (HVSFS) coatings were deposited using these suspensions as feedstock and adopting two different sets of spray parameters.The characteristics of the suspension, particularly its agglomeration behaviour, have a significant influence on the coating deposition mechanism and, hence, on its properties (microstructure, hardness, elastic modulus). Dense and very smooth (Ra ~ 1.3 μm) coatings, consisting of well-flattened lamellae having a homogeneous size distribution, are obtained when micron-sized (~ 1-2 μm) powders with low tendency to agglomeration are employed. Spray parameters favouring the break-up of the few agglomerates present in the suspension enhance the deposition efficiency (up to > 50%), as no particle or agglomerate larger than ~ 2.5 μm can be fully melted. Nano-sized powders, by contrast, generally form stronger agglomerates, which cannot be significantly disrupted by adjusting the spray parameters. If the chosen nanopowder forms small agglomerates (up to a few microns), the deposition efficiency is satisfactory and the coating porosity is limited, although the lamellae generally have a wider size distribution, so that roughness is somewhat higher. If the nanopowder forms large agglomerates (on account of its surface chemistry), poor deposition efficiencies and porous layers are obtained.Although suspensions containing the pure micron-sized powder produce the densest coatings, the highest deposition efficiency (~ 70%) is obtained by suitable mixtures of micron- and nano-sized powders, on account of synergistic effects.     

MoS2颗粒表面包覆Al2O3及其在镀层中的应用

采用非均匀形核法将Al2O3包覆到MoS2颗粒表面,提高颗粒的亲水性能。研究了溶液pH值、Al(NO3)3的摩尔浓度和预处理工艺对包覆率的影响;采用SEM及EDS分析了包覆前后MoS2颗粒的微观形貌和表面成分;通过测量接触角研究了颗粒表面的亲水性。结果表明,颗粒表面均匀包覆了一层Al(OH)3;溶液pH值对包覆率的影响最大,Al(NO3)3的摩尔浓度次之。最佳工艺为:溶液pH值为5.5,Al(NO3)3浓度为0.15mol/L,预处理过程不添加表面活性剂。随着包覆率的提高,MoS2颗粒的亲水性提高。利用包覆Al2O3的MoS2制得了Ni-P-MoS2化学复合镀层,提高了镀层中沉积粒子的均匀致密性。     

Microstructure and mechanical properties of Al2O3-Cr2O3 composite coatings produced by atmospheric plasma spraying

Al₂O₃, Al₂O₃-Cr₂O₃ and Cr₂O₃ coatings were deposited by atmospheric plasma spraying. Phase composition of powders and as-sprayed coatings was determined by X-ray diffraction. Electron probe microanalyzer was employed to investigate the polished and fractured surface morphologies of the coatings. Mechanical properties including microhardness, fracture toughness and bending strength were evaluated. The results indicate that the addition of Cr₂O₃ is conducive to the stabilization of α-Al₂O₃. Compared with the pure Al₂O₃ and Cr₂O₃ coatings, Al₂O₃-Cr₂O₃ composite coatings show lower porosities and denser structures. Heterogeneous nucleation of α-Al₂O₃ occurs over the isostructural Cr₂O₃ lamellae and partial solid solution of Al₂O₃ and Cr₂O₃ might be occurring as well. Furthermore, grain refining and solid solution strengthening facilitate the mechanical property enhancement of Al₂O₃-Cr₂O₃ composite coatings.     

Al_2O_3/MoS_2复合涂层的制备及摩擦磨损性能

以大气等离子喷涂工艺制备的Al_2O_3陶瓷涂层为模板,利用陶瓷涂层中存在的孔隙和微裂纹,采用水热反应在其内部原位合成具有润滑特性的MoS_2,制备出Al_2O_3/MoS_2的复合涂层。结果表明,通过水热反应在陶瓷涂层原有的微观缺陷中成功合成了MoS_2,合成的MoS_2固体粉末呈类球形状,并且这球状的粉末是由纳米片层状的MoS_2搭建组成的。摩擦试验结果表明,与纯Al_2O_3涂层相比,复合涂层中由于MoS_2润滑膜的形成,其摩擦因数和磨损率都显著降低,且载荷越大,复合涂层的摩擦性能越好。     

等离子喷涂Al_2O_(3p)/NiCrBSi涂层优化设计

利用二次回归正交组合设计法优化喷涂工艺参数,建立了等离子喷涂Al2O3p/NiCrBSi复合材料涂层冲蚀磨损失重率的二次回归方程.研究了等离子喷涂参数对涂层冲蚀磨损失重率的影响.结果表明,利用Matlab软件编程计算,优化等离子喷涂参数,明显提高了涂层的抗冲蚀磨损性能.为等离子喷涂制备以氧化铝(Al2O3)颗粒增强金属基(NiCrBSi)复合材料涂层(Al2O3p/NiCrBSi)的实际应用提供必要的理论依据和技术数据.     

等离子喷涂Al2O3/TiO2纳米陶瓷复合涂层的微观结构及性能

采用等离子喷涂技术制备了不同成分的Al2O3/TiO2纳米陶瓷复合涂层,并利用X射线衍射仪(XRD)、扫描电镜(SEM)、显微硬度计和摩擦磨损试验机等分析测试手段研究了纳米陶瓷复合涂层的微观结构与性能.结果表明:纳米陶瓷复合涂层中Al2O3以α-Al2O3和γ-Al2O3两相共存的形式存在,且γ-Al2O3的含量随喷涂功率的增加而增加,而涂层中的TiO2则以金红石型存在;其微结构为完全熔化区的片状微观组织和部分熔化区的纳米级颗粒共存的组织;等离子喷涂功率和TiO2含量对涂层的硬度和耐磨性能均有显著的影响.     

Preparation of nanostructured Ni/Al2O3 composite coatings in high magnetic field

Ni/Al₂O₃ composite coatings were prepared by a novel method from a modified Watt's type electrolyte containing nano-Al₂O₃ particles, where a high magnetic field was imposed in the direction parallel to an electrolytic current instead of mechanical agitation. Effects of magnetic field on the content of particles, surface morphology, microhardness and wear resistance of plating layer were investigated. It was found that the high magnetic field played an important role in the formation of composite coatings. The amounts of nano-Al₂O₃ particles in the composite coating increased with increasing of magnetic flux density and reached a maximum value at 8 T, then reduced slightly. The microhardness and wear resistance of the nanocomposite coatings also enhanced with increasing of magnetic flux density as compared to that of pure Ni coating fabricated in the absence of magnetic field. That was because the co-deposited nano-Al₂O₃ particles were uniformly distributed in the Ni matrix and contributed to greatly increase the microhardness and wear resistance of the composite coatings. Moreover, the mechanism of action of high magnetic field was discussed preliminarily.     

铝合金表面MoS2/Al2O3复合涂层制备及减摩性能研究

铝合金表面减摩涂层设计和制备是改善铝合金构件摩擦性能的关键技术之一。对于目前铝合金结构件易磨损的问题,本研究采用微弧氧化一步法在6063铝合金表面原位合成纳米MoS2,制备具有减摩作用的MoS2/Al2O3复合陶瓷涂层;讨论了硫盐浓度对涂层成分、形貌及摩擦性能的影响,分析了涂层减摩机理。结果表明：通过微弧氧化在6063铝合金表面成功制备出了含有MoS2的自润滑复合陶瓷涂层;涂层的摩擦系数随着硫盐浓度的升高呈现先下降后上升的趋势,当电解液中硫盐浓度为15g/L时涂层的摩擦系数为0.15,较常规微弧氧化涂层降低了76%。涂层中的MoS2分布在涂层的表面和内部,在与摩擦副接触与挤压的作用下形成均匀分布的MoS2润滑膜,表现出良好的减摩性能。     

Development of moderate temperature CVD Al2O3 coatings

Chemically vapor deposited Al₂O₃ coatings, due to their high hardness and chemical inertness, are currently the state of art in the cutting tool industry. The conventional high deposition temperature of about 1050 °C for Al₂O₃ coatings, based on the water–gas shift process, has to a great extend restricted the development of several hybrid coatings, such as TiC/TiN/TiCN/Al₂O₃. To overcome this limitation, alternate systems to deposit Al₂O₃ at moderate temperatures have been investigated. Systems using NO–H₂, H₂O₂, NO₂–H₂ and HCOOH were identified and thermodynamic calculations were performed to evaluate them as potential sources of oxygen donors to form Al₂O₃ in the moderate temperature range of 700–950 °C. Preliminary results have clearly demonstrated that it is possible to grow moderate temperature alumina (using such alternate sources) on the TiC/TiN coated cemented carbide substrates.     

国外多孔基体氧化铝/氧化铝复合材料工程应用进展

氧化铝/氧化铝复合材料(Al2O3/Al2O3)是20世纪90年代兴起的一类连续陶瓷纤维增强陶瓷基复合材料,已经发展为与SiC/SiC、C/SiC等非氧化物陶瓷基复合材料并列的一类陶瓷基复合材料。与非氧化物陶瓷基复合材料相比,Al2O3/Al2O3具有长时抗氧化、高温耐腐蚀、低成本等独特优势,已经在航空发动机、地面燃气轮机等军民两用热结构材料领域展现出广阔的应用前景。本文从材料应用的角度出发,系统分析阐述了目前在Al2O3/Al2O3占主导地位的多孔基体Al2O3/Al2O3(P-Al2O3/Al2O3)的增韧机制、成型工艺和性能特点,重点归纳了国外近年来P-Al2O3/Al2O3的工程化应用进展及前景,最后指出了P-Al2O3/Al2O3存在的局限性并展望了未来发展方向,旨在为国内Al2O3/Al2O3体系发展提供借鉴和参考。     

Application of the induction plasma to the synthesis of two dimensional steam methane reforming Ni/Al2O3 catalyst

The purpose of the study is to develop a new protocol for preparing supported two dimensional catalysts with high external and low internal surface by combining thermal plasma spraying and thermal plasma chemical vapour deposition (TPCVD) processes. The method was tested for the production of an Al₂O₃ supported Ni catalysts used for methane steam reforming. The deposition of catalytic materials is made in 2 successive steps. The first step deals with alumina powder sprayed by induction plasma spraying (IPS) on a molybdenum substrate. The experimental conditions have been turned towards γ-Al₂O_3. The second stage deals with the deposition of nickel at the nanometric scale on the alumina layer using the thermal plasma chemical vapour deposition method. This last step was focused on the study of the influence of the nozzle type employed for the nickel solution spraying, the reactor internal pressure, the concentration and the flow rate of nickel salts solution, Ni(NO₃)₂·6H₂O, on the catalyst response. The formulations were tested as methane steam reforming catalysts.The results demonstrate that the catalyst morphology depends on plasma projection conditions and show the effectiveness of combining IPS and TPCVD processes for producing catalysts in methane steam reforming.     

Al2O3-nanodiamond composite coatings with high durability and hydrophobicity prepared by aerosol deposition

We attempted the room-temperature fabrication of Al₂O₃-based nanodiamond (ND) composite coating films on glass substrates by an aerosol deposition (AD) process to improve the anti-scratch and anti-smudge properties of the films. Submicron Al₂O₃ powder capable of fabricating transparent hard coating films was used as a base material for the starting powders, and ND treated by 1H,1H,2H,2H-perfluorooctyltriethoxysilane (PFOTES) was added to the Al₂O₃ to increase the hydrophobicity and anti-wear properties. The ND powder treated by PFOTES was mixed with the Al₂O₃ powder by ball milling to ratios of 0.01 wt.%, 0.03 wt.%, and 0.05 wt.% ND. The water contact angle (CA) of the Al₂O₃-ND composite coating films was increased as the ND ratio increased, and the maximum water CA among all the films was 110°. In contrast to the water CA, the Al₂O₃-ND composite coating films showed low transmittance values of below 50% at a wavelength of 550 nm due to the strong agglomeration of ND. To prevent the agglomeration of ND, the starting powders were mixed by attrition milling. As a result, Al₂O₃-ND composite coating films were produced that showed high transmittance values of close to 80%, even though the starting powder included 1.0 wt.% ND. In addition, the Al₂O₃-ND composite coating films had a high water CA of 109° and superior anti-wear properties compared to those of glass substrates.     

Cu基体上抗原子氧侵蚀的A12O3涂层

在原子氧地面模拟设备中对铜片、A12O3涂层试样进行了原子氧暴露实验，采用XPS、SEM等分析手段对暴露前后试样表面的物理和化学变化进行了研究。结果表明：Cu受到原子氧的侵蚀，质量有少许增加，表面形貌和电学性能有些变化；A1203涂层质量变化很小，对基体提供了良好的保护作用。XPS分析结果表明Cu表面形成CuO氧化物层。反应溅射的A12O3涂层是富A1的，初始暴露时由于氧化反应而质量有少许增加，随时间延长，涂层变得完全符合化学计量。     

Microstructure, spallation and corrosion of plasma sprayed Al2O3–13%TiO2 coatings

The electrochemical corrosion behaviours of the steel substrates coated with three different plasma sprayed Al₂O₃–13%TiO₂ coatings were studied in this paper. The three kinds of Al₂O₃–13%TiO₂ coatings were conventional ME coating, nanostructured NP coating and NS coating. There were micro cracks, laminar splats and straight columnar grains in ME coating. For the two nanostructured coatings, the laminar microstructure and columnar grains were not obvious. The NP coating had the highest hardness and spallation resistance. Electrochemical corrosion behaviour of the three coatings was mainly investigated by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) in aqueous Na₂SO₄ solution.     

MoSi_2含量对MoSi_2/Al_2O_3复合涂层介电与力学性能的影响(英文)

通过喷雾干燥法制备MoSi2包覆Al2O3的壳核结构混合粉,利用该混合粉以等离子喷涂技术制备MoSi2/Al2O3复合涂层材料。研究MoSi2/Al2O3质量比涂层材料的力学和介电性能的影响。结果表明:随着MoSi2含量从0增加到45%,复合材料的抗弯强度和断裂韧性分别从198MPa和3.05MPa·m1/2增加到324MPa和4.82MPa·m1/2,随后又降到310MPa和4.67MPa·m1/2。在8.2-12.4GHz微波频率波段内,随着MoSi2含量的增加,复合材料的介电损耗增加,而介电常数的实部却呈减小趋势。这主要是由于MoSi2颗粒熔化后的凝聚及导电网络结构的形成导致电导率的增加引起的。