Toughening and strengthening mechanism of plasma sprayed nanostructured Al2O3–13 wt.%TiO2 coatings

The starting materials of Al₂O₃, TiO₂, ZrO₂ and CeO₂ nanoparticles were agglomerated into sprayable feedstock powders and plasma sprayed to form nanostructured coatings. There were net structures and fused structures in plasma sprayed nanostructured Al₂O₃–13 wt.%TiO₂ coatings. The net structures were derived from partially melted feedstock powders and the fused structures were derived from fully melted feedstock powders. The nanostructured Al₂O₃–13 wt.%TiO₂ coatings possessed higher hardness, bonding strength and crack growth resistance than conventional Metco 130 coatings which were mainly composed of lamellar fused structures. The higher toughness and strength of nanostructured Al₂O₃–13 wt.%TiO₂ coatings were mainly related to the obtained net structures.     

Plasma spray coating of spray-dried Cr2O3/wt.% TiO2 powder

An agglomerated Cr₂O₃/wt.%TiO₂ powder has been fabricated by the spray drying process under different parameters. The spray-dried powder has well-agglomerated particles of spherical shape. In the conditions of the high slurry feed rate and low binder concentration in the slurry, the powder has large cavities inside some particles and ruggedness over their surface. The optimum plasma spray feed rate has been found by examining the spraying behavior of the powder and melted state of particles. The plasma spray coating has been performed under different process variables such as spraying distance and plasma power. These parameters strongly affect the characteristics of the coated layer: microstructure, hardness, and bond strength.     

Superior performance of high-velocity oxyfuel-sprayed nanostructured TiO<Subscript>2</Subscript> in comparison to air plasma-sprayed conventional Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-13TiO<Subscript>2</Subscript>

Air plasma-sprayed conventional alumina-titania (Al₂O₃-13wt.%TiO₂) coatings have been used for many years in the thermal spray industry for antiwear applications, mainly in the paper, printing, and textile industries. This work proposes an alternative to the traditional air plasma spraying of conventional aluminatitania by high-velocity oxyfuel (HVOF) spraying of nanostructured titania (TiO₂). The microstructure, porosity, hardness (HV 300 g), crack propagation resistance, abrasion behavior (ASTM G65), and wear scar characteristics of these two types of coatings were analyzed and compared. The HVOF-sprayed nanostructured titania coating is nearly pore-free and exhibits higher wear resistance when compared with the air plasma-sprayed conventional alumina-titania coating. The nanozones in the nanostructured coating act as crack arresters, enhancing its toughness. By comparing the wear scar of both coatings (via SEM, stereoscope microscopy, and roughness measurements), it is observed that the wear scar of the HVOF-sprayed nanostructured titania is very smooth, indicating plastic deformation characteristics, whereas the wear scar of the air plasma-sprayed alumina-titania coating is very rough and fractured. This is considered to be an indication of a superior machinability of the nanostructured coating.     

Mechanical and tribological performance of Al2O3-TiO2 coatings elaborated by flame and plasma spraying

Mechanical properties and wear rates of Al₂O₃-13 wt.% TiO₂ (AT-13) and Al₂O₃-43 wt.% TiO₂ (AT-43) coatings obtained by flame and atmospheric plasma spraying were studied. The feed stock was either ceramic cords or powders. Results show that the wear resistance of AT-13 coatings is higher than that of AT-43 and it seems that the effect of hardness on wear resistance is more important than that of toughness. Additionally, it was established that, according to conditions used to elaborate coatings and the sliding tribological test chosen, spray processes do not seem to have an important effect on the wear resistance of these coatings.     

超音速等离子喷涂工艺参数对 Cr2O3涂层硬度的影响

目的研究影响超音速等离子喷涂Cr2O3涂层硬度的主要因素,制备出高硬度涂层。方法首先采用单变量法研究超音速等离子生成气体压力(空气压力)和喷涂距离对涂层显微结构的影响,然后采用正交试验研究喷涂电流、空气压力、喷涂距离对Cr2O3涂层硬度的影响。结果工艺参数对Cr2O3涂层硬度影响的主次顺序为:空气压力>喷涂电流>喷涂距离。结论获得高硬度涂层的最佳工艺参数组合为:空气压力0.4 MPa,喷涂电流270 A,喷涂距离200 mm。在该工艺条件下获得的涂层致密、均匀,孔隙率小。     

Preparation of nanostructured Ni/Al2O3 composite coatings in high magnetic field

Ni/Al₂O₃ composite coatings were prepared by a novel method from a modified Watt's type electrolyte containing nano-Al₂O₃ particles, where a high magnetic field was imposed in the direction parallel to an electrolytic current instead of mechanical agitation. Effects of magnetic field on the content of particles, surface morphology, microhardness and wear resistance of plating layer were investigated. It was found that the high magnetic field played an important role in the formation of composite coatings. The amounts of nano-Al₂O₃ particles in the composite coating increased with increasing of magnetic flux density and reached a maximum value at 8 T, then reduced slightly. The microhardness and wear resistance of the nanocomposite coatings also enhanced with increasing of magnetic flux density as compared to that of pure Ni coating fabricated in the absence of magnetic field. That was because the co-deposited nano-Al₂O₃ particles were uniformly distributed in the Ni matrix and contributed to greatly increase the microhardness and wear resistance of the composite coatings. Moreover, the mechanism of action of high magnetic field was discussed preliminarily.     

The effect of plasma spray parameters on the cavitation erosion of Al2O3-TiO2 coatings

This paper reports a study of how the choice of plasma spray parameters, used during deposition of Al₂O₃-13%TiO₂ coatings on carbon steel, influences the cavitation erosion properties of such coatings. The parameters studied are the power feeding rate and hydrogen flow rate. The surface and cross section of coatings before and after cavitation were also observed by scanning electron microscopy (SEM). The phases present in the coatings were characterized by X-ray diffraction method (XRD). The microscopic observations were used to study the inter-lamellar connection, porosity, unmelted particles and so on inside the coating. We also measured the roughness, microhardness, adhesion strength and cavitation erosion of the coatings. The XRD results showed that the coating includes different allotropes of Al₂O₃ such as α and γ. The cavitation erosion studies of the coatings were conducted by ultrasonic cavitation testing on the basis of ASTM G32 standard. It was found that cavitation erosion is accelerated around the unmelted particles and porosities. The results reveal that the cavitation resistance of the coating is determined by its microstructure and that increasing discontinuities (inside the coating) reduce its cavitation resistance. We have found that the coating obtained at hydrogen gas flow rate of 16 L/min and powder feeding rate of 20 g/min has the best cavitation resistance.     

Characterization of plasma-sprayed Y2O3 coating and investigation of its visual aspect change

Yttria (Y₂O₃) has been commonly used as a protective coating material because it has strong resistance to plasma erosion with reducing the amount of reaction products generated during the semiconductor/LCD fabrication process. We have investigated the visual aspect of the plasma-sprayed Y₂O₃ coating both experimentally and numerically to propose the process conditions proper for white Y₂O₃ coating. It was demonstrated that heating of the particle surface in oxygen deficient plasma jet core resulted in the reduction of coating materials associated with the formation of black spots, while the re-oxidation of reduced feed stock materials at long spray distance, where they were exposed to relatively lower temperature of plasma and abundant oxygen, caused the whitening of coating. Based on the results, we proposed a spray coating condition proper for reducing the black spots formed in protective Y₂O₃ ceramic coating.     

HVOF-Sprayed Coatings Engineered from Mixtures of Nanostructured and Submicron Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-TiO<Subscript>2</Subscript> Powders: An Enhanced Wear Performance

In previous studies, it has been demonstrated that nanostructured Al₂O₃-13 wt.%TiO₂ coatings deposited via air plasma spray (APS) exhibit higher wear resistance when compared to that of conventional coatings. This study aimed to verify if high-velocity oxy-fuel (HVOF)-sprayed Al₂O₃-13 wt.%TiO₂ coatings produced using hybrid (nano + submicron) powders could improve even further the already recognized good wear properties of the APS nanostructured coatings. According to the abrasion test results (ASTM G 64), there was an improvement in wear performance by a factor of 8 for the HVOF-sprayed hybrid coating as compared to the best performing APS conventional coating. When comparing both hybrid and conventional HVOF-sprayed coatings, there was an improvement in wear performance by a factor of 4 when using the hybrid material. The results show a significant antiwear improvement provided by the hybrid material. Scanning electron microscopy (SEM) at low/high magnifications showed the distinctive microstructure of the HVOF-sprayed hybrid coating, which helps to explain its excellent wear performance. This article is an invited paper selected from presentations at the 2007 International Thermal Spray Conference and has been expanded from the original presentation. It is simultaneously published in Global Coating Solutions, Proceedings of the 2007 International Thermal Spray Conference, Beijing, China, May 14-16, 2007, Basil R. Marple, Margaret M. Hyland, Yuk-Chiu Lau, Chang-Jiu Li, Rogerio S. Lima, and Ghislain Montavon, Ed., ASM International, Materials Park, OH, 2007.     

热喷涂TiB2-Ni复合涂层组织结构和力学性能

采用团聚烧结方法制备TiB₂-Ni复合粉末喂料,并采用大气等离子喷涂和高速火焰喷涂两种喷涂方法制备了TiB₂-Ni涂层,比较分析了两种涂层的显微组织、物相组成、孔隙率、硬度和断裂韧性.结果表明,与等离子喷涂相比,高速火焰喷涂制备的TiB₂-Ni涂层具有更高的致密度,TiB₂含量,硬度和断裂韧性.两种涂层中TiB₂都没有发生明显的脱硼,氧化,但等离子喷涂过程中TiB₂向金属相中发生了溶解生成了大量脆性Ni₂₀Ti₃B₆相,并降低了涂层中TiB₂的含量,这是涂层硬度和断裂韧性相对较低的主要原因.     

Thermal shock behavior of nanostructured and conventional Al2O3/13 wt%TiO2 coatings fabricated by plasma spraying

The thermal shock behavior of three kinds of Al₂O₃/13 wt%TiO₂ coatings fabricated by plasma spraying was studied in this paper. One kind of those coatings was derived from conventional fused and crushed feedstock powder available commercially; the other two kinds of coatings were derived from nanostructured agglomerated feedstock powders. These two nano coatings possess moderate pores and pre-existing microcracks, they were composed of fused structure and three-dimensional net or skeleton-like structure. For conventional coatings, the pores and pre-existing cracks were bigger, sharp-point and mostly distributed between splats. Thermal shock tests for the three coatings were performed by water quenching method. Testing result showed the two kinds of nano coatings had much higher thermal shock resistance than the conventional coatings. The improved thermal shock resistance for nano coatings could attribute to their improved microstructure and crack propagation mode. The damage evolution and failure mechanism of coatings was quite different at thermal shock temperature of 650 °C and 850 °C, which was explained by a simple model. Different crack propagating modes in nanostructured and conventional coatings during thermal shock tests were due to their different microstructures in these two kinds coatings. The stress state of coating surfaces during the thermal cycles was also discussed in this paper.     

Effect of Feedstock Size and its Distribution on the Properties of Detonation Sprayed Coatings

The detonation spraying is one of the most promising thermal spray variants for depositing wear and corrosion resistant coatings. The ceramic (Al₂O₃), metallic (Ni-20 wt%Cr) , and cermets (WC-12 wt%Co) powders that are commercially available were separated into coarser and finer size ranges with relatively narrow size distribution by employing centrifugal air classifier. The coatings were deposited using detonation spray technique. The effect of particle size and its distribution on the coating properties were examined. The surface roughness and porosity increased with increasing powder particle size for all the coatings consistently. The feedstock size was also found to influence the phase composition of Al₂O₃ and WC-Co coatings; however does not influence the phase composition of Ni-Cr coatings. The associated phase change and %porosity of the coatings imparted considerable variation in the coating hardness, fracture toughness, and wear properties. The fine and narrow size range WC-Co coating exhibited superior wear resistance. The coarse and narrow size distribution Al₂O₃ coating exhibited better performance under abrasion and sliding wear modes however under erosion wear mode the as-received Al₂O₃ coating exhibited better performance. In the case of metallic (Ni-Cr) coatings, the coatings deposited using coarser powder exhibited marginally lower-wear rate under abrasion and sliding wear modes. However, under erosion wear mode, the coating deposited using finer particle size exhibited considerably lower-wear rate.     

Deposition of Al2O3-TiO2 Nanostructured Powders by Atmospheric Plasma Spraying

Al₂O₃-13%TiO₂ coatings were deposited on stainless steel substrates from conventional and nanostructured powders using atmospheric plasma spraying (APS). A complete characterization of the feedstock confirmed its nanostructured nature. Coating microstructures and phase compositions were characterized using SEM, TEM, and XRD techniques. The microstructure comprised two clearly differentiated regions. One region, completely fused, consisted mainly of nanometer-sized grains of γ-Al₂O₃ with dissolved Ti⁺⁴. The other region, partly fused, retained the microstructure of the starting powder and was principally made up of submicrometer-sized grains of α-Al₂O₃, as confirmed by TEM. Coating microhardness as well as tribological behavior were determined. Vickers microhardness values of conventional coatings were in average slightly lower than the values for nanostructured coating. The wear resistance of conventional coatings was shown to be lower than that of nanostructured coatings as a consequence of Ti segregation. A correlation between the final properties, the coating microstructure, and the feedstock characteristics is given.     

Y2O3对原位自生TiC增强Ni基涂层组织和性能影响

采用氩弧熔覆的方法,以Ni60A自熔性合金粉末为粘结相,添加Ti粉、C粉和不同含量的稀土氧化物Y₂O₃,在16Mn钢基体上制备出TiC陶瓷颗粒增强金属基熔覆涂层. 运用XRD, SEM等手段对复合涂层的显微组织进行表征和分析,并对熔覆涂层的硬度及耐磨性进行了测试. 结果表明,适量添加Y₂O₃可以使涂层组织中枝晶的方向性减弱、同时细化涂层组织,使涂层组织更加均匀,涂层的硬度和耐磨性有显著提高. 添加2% Y₂O₃熔覆涂层的组织为最细,涂层具有较高的显微硬度和良好的耐磨性能.     

Mechanical and tribological properties of plasma-sprayed Cr3C2-NiCr, WC-Co, and Cr2O3 coatings

Mechanical properties such as Young’s moduli and fracture toughness of plasma-sprayed Cr₃C₂-NiCr, WC-Co and Cr₂O₃ coatings were measured. The tribological properties of the three kinds of coatings were investigated with a block-on-ring self-mated arrangement under water-lubricated sliding. Furthermore, the influences of the mechanical properties on the tribological properties of the coatings were also examined. It was found that the Young’s moduli, bend strengths and fracture toughness of the coatings were lower than the corresponding bulk materials, which may be attributed to the existence of pores and microcracks in the coatings. Among the three kinds of coatings, the magnitude of wear coefficients, in decreasing order, is Cr₃C₂-NiCr, WC-Co and Cr₂O₃, and the wear coefficient of Cr₂O₃ coating was less than 1 × 10⁻⁶mm³N⁻¹m⁻¹. The wear mechanisms of the coatings were explained in terms of microcracking and fracturing, and water deteriorated wear performance of the coatings. The higher the fracture toughness and the lower the porosity and length of microcracking of the coating, the more the wear-resistance of the coating.     

The use of Al-Al2O3 cold spray coatings to improve the surface properties of magnesium alloys

Pure Al and 6061 aluminium alloy based Al₂O₃ particle-reinforced composite coatings were produced on AZ91E substrates using cold spray. The strength of the coating/substrate interface in tension was found to be stronger than the coating itself. The coatings have corrosion resistance similar to that of bulk pure aluminium in both salt spray and electrochemical tests. The wear resistance of the coatings is significantly better than that of the AZ91 Mg substrate, but the significant result is that the wear rate of the coatings is several decades lower than that of various bulk Al alloys tested for comparison. The effect of post-spray heat treatment, the volume fraction of Al₂O₃ within the coating and of the type of Al powder used in the coatings on the corrosion and wear resistance was also discussed.     

Effect of applied current on the electrodeposited Ni-Al2O3 composite coatings

Nano-sized Al₂O₃ ceramic particles (50 nm) were co-deposited with nickel using electrodeposition technique to develop composite coatings. The coatings were produced in an aqueous nickel bath at different current densities and the research investigated the effect of applied current on microstructure and thickness of the coatings. The variation in some mechanical properties such as hardness, wear resistance, and the adhesive strength of the composite coatings is influenced by the applied current and this was also studied. The morphology of the coatings was characterized by scanning electron microscopy and energy dispersive X-ray spectroscopy. The hardness, wear resistance, and bond strength of the coatings were evaluated by Vickers micro-hardness test, pin-on-disc test, and tensile test, respectively. Results showed that the Al₂O₃ particles were uniformly distributed in the coatings, and the coatings deposited at a current density of 0.01 A/cm² was most favorable in achieving a maximum current efficiency which causes the co-deposition of a maximum amount of Al₂O₃ particles (4.3 wt.%) in the coatings. The increase in Al₂O₃ particles in the coatings increased the mechanical properties of the Ni-Al₂O₃ composite coatings by grain refining and dispersion strengthening mechanisms.     

Microstructural characterization of plasma sprayed Al2O3-40 wt.% TiO2 coatings on high density graphite with different post-treatments

Graphite is one of the candidate materials proposed for application in pyrochemical reprocessing plants involving aggressive molten chloride environment. Post treatments are promising techniques for the improvement of properties of thermal spray coatings for different industrial applications. In the present work, the effect of post treatments like vacuum annealing (VA) and laser melting (LM) on the microstructure and chemical modification of plasma sprayed Al₂O₃-40 wt.% TiO₂ coatings over high density (HD) graphite substrates has been investigated. When compared with sprayed coatings (SC), VA coatings showed cluster morphology and LM coatings exhibited homogenous microstructure. On laser melted surfaces networks of cracks were observed. XRD studies showed that the metastable γ-Al₂O₃ phase present in the SC is transformed to stable α-Al₂O₃ after post treatments. In LM coatings Al₂TiO₅ phase was more predominant in contrast to SC and VA coatings. The microhardness enhancement was observed in case of LM coating compared to the VA and SC. Due to elimination of coating defects in LM samples, there is a considerable reduction in the surface roughness.     

Thermal conductivity and thermal cycle life of La2O3 and HfO2 doped ZrO2-Y2O3 coatings produced by EB-PVD

The effects of La₂O₃ and HfO₂ addition on thermal conductivity and thermal cycle life of EB-PVD YSZ coatings were investigated. La₂O₃ and HfO₂ were selected as additives, because they significantly suppress the sintering of YSZ. The developed coating showed low thermal conductivity as well as high resistance to sintering. Burner rig tests confirmed that the developed coating have a superior thermal insulating effect and have a longer life than that of a coating with conventional composition.     

Influence of cold gas spray parameters on the corrosion resistance of Al-Al2O3 coatings sprayed on carbon steel

ABSTRACT

This work describes the influence of standoff distance (SoD), and gas temperature on the morphology and corrosion resistance of Al-10%Al₂O₃ coatings deposited by cold gas spray (CGS) on carbon steel. The results showed that the standoff distance had little effect on the thickness and microstructure of the coating. However, a 100 °C decrease of the spraying temperature reduced the coating thickness by 300?µm. The use of electrochemical analyses and SEM images showed that all the coatings studied were able to protect the substrate during at least 1300?h of immersion, due to the dense microstructure obtained by CGS.