A 5-GHz low phase noise differential colpitts CMOS VCO

A low noise 5-GHz differential Colpitts CMOS voltage-controlled oscillator (VCO) is proposed in this letter. The Colpitts VCO core adopts only PMOS in a 0.18-/spl mu/m CMOS technology to achieve a better phase noise performance since PMOS has lower 1/f noise than NMOS. The VCO operates from 4.61 to 5 GHz with 8.3% tuning range. The measured phase noise at 1-MHz offset is -120.42 dBc/Hz at 5 GHz and -120.99 dBc/Hz at 4.61 GHz. The power consumption of the VCO core is only 3 mW. To the authors' knowledge, this differential Colpitts CMOS VCO achieves the best figure of merit (FOM) of 189.6 dB at 5-GHz band.     

Millimeter-wave voltage-controlled oscillators in 0.13-/spl mu/m CMOS technology

This paper describes the design of CMOS millimeter-wave voltage controlled oscillators. Varactor, transistor, and inductor designs are optimized to reduce the parasitic capacitances. An investigation of tradeoff between quality factor and tuning range for MOS varactors at 24 GHz has shown that the polysilicon gate lengths between 0.18 and 0.24 /spl mu/m result both good quality factor (>12) and C/sub max//C/sub min/ ratio (/spl sim/3) in the 0.13-/spl mu/m CMOS process used for the study. The components were utilized to realize a VCO operating around 60 GHz with a tuning range of 5.8 GHz. A 99-GHz VCO with a tuning range of 2.5 GHz, phase noise of -102.7 dBc/Hz at 10-MHz offset and power consumption of 7-15mW from a 1.5-V supply and a 105-GHz VCO are also demonstrated. This is the CMOS circuit with the highest fundamental operating frequency. The lumped element approach can be used even for VCOs operating near 100-GHz and it results a smaller circuit area.     

A low-power 2/5.8-GHz dual-wide-band CMOS LC-VCO with switched-inductor technique

A fully integrated dual-band LC voltage control oscillator, designed in a 0.18-µm CMOS technology for 5.8-GHz/2.0-GHz wireless communication applications, is described. The frequency band switching is accomplished with switched-inductor technique. The dual-band oscillator can be operated in 5.38–6.23?GHz and 1.78–2.07?GHz with 15% frequency tuning range. Two different inductors are used for the frequency band switching. Frequency tuning is implemented by varying the capacitance of a MOS varactor. The measured phase noise is ?109?dBc/Hz @ 1?MHz and ?112?dBc/Hz @ 1?MHz for frequency at 5.8?GHz and 2?GHz, respectively. This oscillator is fabricated in UMC's 0.18-µm one-poly-six-metal 1.8?V process. The power dissipation of this dual-band VCO is 11.7 and 9.3?mW for oscillation frequency of 2?GHz and 5.8?GHz, respectively.     

Design of wide-band CMOS VCO for multiband wireless LAN applications

In this paper, a general design methodology of low-voltage wide-band voltage-controlled oscillator (VCO) suitable for wireless LAN (WLAN) application is described. The applications of high-quality passives for the resonator are introduced: 1) a single-loop horseshoe inductor with Q > 20 between 2 and 5 GHz for good phase noise performance; and 2) accumulation MOS (AMOS) varactors with C/sub max//C/sub min/ ratio of 6 to provide wide-band tuning capability at low-voltage supply. The adverse effect of AMOS varactors due to high sensitivity is examined. Amendment using bandswitching topology is suggested, and a phase noise improvement of 7 dB is measured to prove the concept. The measured VCO operates on a 1-V supply with a wide tuning range of 58.7% between 3.0 and 5.6 GHz when tuned between /spl plusmn/0.7 V. The phase noise is -120 dBc/Hz at 3.0 GHz, and -114.5 dBc/Hz at 5.6 GHz, with the nominal power dissipation between 2 and 3 mW across the whole tuning range. The best phase noise at 1-MHz offset is -124 dBc/Hz at the frequency of 3 GHz, a supply voltage of 1.4 V, and power dissipation of 8.4 mW. When the supply is reduced to 0.83 V, the VCO dissipates less than 1 mW at 5.6 GHz. Using this design methodology, the feasibility of generating two local oscillator frequencies (2.4-GHz ISM and 5-GHz U-NII) for WLAN transceiver using a single VCO with only one monolithic inductor is demonstrated. The VCO is fabricated in a 0.13-/spl mu/m partially depleted silicon-on-insulator CMOS process.     

A Low-Power 114-GHz Push–Push CMOS VCO Using LC Source Degeneration

An LC source-degeneration negative-resistance cell of an LC VCO is investigated, which is capable of operating at millimeter-wave (MMW) range with low dc power consumption. Several negative-resistance cells in LC oscillators are also compared. The LC source-degenerated topology is demonstrated through a 114-GHz push-push fully integrated LC VCO implemented in TSMC 0.13-mum CMOS process. With core power consumption of 8.4 mW, the tuning range at the fundamental port is 56.4-57.6 GHz and at the push-push port is 112.8-115.2 GHz. The measured phase noise at the fundamental port is -13.6 dBc/Hz at 10-MHz offset. This VCO is believed to have the best figure of merit among MMW VCOs using bulk CMOS processes.     

A low-phase-noise and low-power multiband CMOS voltage-controlled oscillator

A low voltage multiband all-pMOS VCO was fabricated in a 0.18-/spl mu/m CMOS process. By using a combination of inductor and capacitor switching, four band (2.4, 2.5, 4.7, and 5 GHz) operation was realized using a single VCO. The VCO with an 1-V power supply has phase noises at 1-MHz offset from a 4.7-GHz carrier of -126 dBc/Hz and -134 dBc/Hz from a 2.4-GHz carrier. The VCO consumes 4.6 mW at 2.4 and 2.5 GHz, and 6 mW at 4.7 and 5 GHz, respectively. At 4.7 GHz, the VCO also achieves -80 dBc/Hz phase noise at 10-kHz offset with 2 mW power consumption.     

A low-phase-noise 5-GHz CMOS quadrature VCO using superharmonic coupling

A new concept for quadrature coupling of LC oscillators is introduced and demonstrated on a 5-GHz CMOS voltage-controlled oscillator (VCO). It uses the second harmonic of the outputs to couple the oscillators. The technique provides quadrature over a wide tuning range without introducing any increase in phase noise or power consumption. The VCO is tunable between 4.57 and 5.21 GHz and has a phase noise lower than -124 dBc/Hz at 1-MHz offset over the entire tuning range. The worst-case measured image rejection is 33 dB. The circuit draws 8.75 mA from a 2.5-V supply.     

An Integrated 5–2.5-GHz Direct-Injection Locked Quadrature LC VCO

This letter presents an integrated direct-injection locked quadrature voltage controlled oscillator (VCO), consisted of a 5-GHz VCO integrated with injection locked LC frequency dividers for low-power quadrature generation. The circuit is implemented using a standard 0.18-mum CMOS process. The differential VCO is a full PMOS Colpitts oscillator, and the frequency divider is performed by adding an injection nMOS between the differential outputs of complementary cross-coupled np-core LC VCO. The measurement results show that at the supply voltage of 1.8-V, the master 5-GHz VCO is tunable from 4.73 to 5.74GHz, and the slave 2.5-GHz VCO is tunable from 2.36 to 2.87GHz. The measured phase noise of master VCO is -118.2dBc/Hz while the locked quadrature output phase noise is -124.4dBc/Hz at 1-MHz offset frequency, which is 6.2dB lower than the master VCO. The core power consumptions are 7.8 and 8.7mW at master and slave VCOs, respectively     

Dual-band ultra-wide tuning range CMOS voltage-controlled oscillator

A dual-band wide-tuning range LC CMOS voltage controlled oscillator (VCO) topology is proposed. Dual-band operation is realised by employing a double-tuned double-driven transformer as a resonator. The proposed approach eliminates MOS switches, which are typically used in multi-standard oscillators, and thus improves phase noise and tuning range characteristics. The concept is demonstrated through the design of an LC VCO in a standard 0.18 mum CMOS process. Two frequency bands are realised (2.4 and 6 GHz) with 740 MHz tuning range in the first band and 1.56 GHz tuning range in the second band. Operating from a 1.8 V supply, the VCO has a simulated phase noise of -119 dBc/Hz in the 2.4 GHz band and -110 dBc/Hz in the 6 GHz band at 600 KHz offset from the carrier     

A novel complementary Colpitts differential CMOS VCO with low phase noise performance

A low phase noise Ka-band CMOS voltage-controlled oscillator is proposed in this paper. A new complementary Colpitts structure was adopted in a 0.18-μm CMOS process to achieve differential-ended outputs, low phase-noise performance, and low-power consumption. The designed VCO oscillates from 29.8 to 30 GHz with 200 MHz tuning range. The measured phase noise at 1-MHz offset is −109 dBc/Hz at 30 GHz and −105.5 dBc/Hz at 29.8 GHz. The power consumption of VCO is only 27 mW. In addition, compared with the published papers, the proposed CMOS VCO achieves the best figure of merit (FOM) of −185 dB at 29.95-GHz band.     

4.2GHz 1.8V CMOS LC压控振荡器

基于Hajimiri提出的VCO相位噪声模型,分析了差分LC VCO电路参数对于相位噪声的影响。根据前面的分析,详细介绍了LC VCO电路的设计方法:包括高Q值片上电感的设计、变容MOS管的设计以及尾电流的选取。采用SMIC 0.18μm 1P6 M、n阱、混合信号CMOS工艺设计了一款4.2GHz 1.8V LC VCO。测试结果表明:当输出频率为4.239GHz时,频偏1MHz处的相位噪声为-101dBc/Hz,频率调节范围为240MHz。     

A 2.4 GHz high-linearity low-phase-noise CMOS LC-VCO based on capacitance compensation

A 2.4 GHz high-linearity low-phase-noise cross-coupled CMOS LC voltage-controlled oscillator(VCO) is implemented in standard 0.18-μm CMOS technology.An equalization structure for tuning sensitivity base on the three-stage distributed biased switched-varactor bank and the differential switched-capacitor bank is adopted to reduce the variations of the VCO gain,achieve high linearity,and optimize the phase-noise performance.Compared to the conventional VCO,the proposed VCO has more constant gain over the en...     

A 1.9-GHz CMOS VCO with micromachined electromechanically tunablecapacitors

This paper presents a 1.9-GHz CMOS voltage-controlled oscillator (VCO) where the resonant circuit consists of micromachined electromechnically tunable capacitors and a bonding wire inductor. The tunable capacitors were implemented in a MUMP's polysilicon surface micromachining process. These devices have a nominal capacitance of 2.1 pF and a quality factor (Q-factor) of 9.3 at 1.9 GHz. The capacitance is variable from 2.1 pF to 2.9 pF within a 4-V control, voltage range. The active circuits were fabricated in a 0.5-μm CMOS process. The VCO was assembled in a ceramic package where the MUMP's and CMOS dice were bonded together. The experimental VCO achieves a phase noise of -98 dBc/Hz and -126 dBc/Hz at 100 kHz and 600 kHz offsets from the carrier, respectively. The tuning range of the VCO is 9%. The VCO circuit and the output buffer consume 15 mW and 30 mW from a 2.7-V power supply, respectively     

5-GHz Low Phase-Noise CMOS VCO Integrated With a Micromachined Switchable Differential Inductor

A 5-GHz CMOS voltage-controlled oscillator (VCO) integrated with a micromachined switchable differential inductor is reported in a 0.18 mum radio frequency-CMOS-based microelectromechanical system technology. The power consumption of the core is about 8 mW at the supply voltage of 1.8 V. A total tuning range of 470 MHz (from 5.13 GHz to 5.60 GHz) is achieved as the tuning voltage ranging from 0 V to 1.8 V. In the practical tuning range, the measured phase noise performances at 1 MHz offset are less than -125 dBc/Hz and -126 dBc/Hz when the inductor switch is turned on and off, respectively. The figure-of-merit is better than -190 dB. When compared with a contrast VCO circuit that utilizes a standard switchable differential inductor, this oscillator reaches a phase noise improvement of around 3 dB as the switch is turned on. Around 1-dB on-off phase noise difference can be achievable.     

A 15/30-GHz Dual-Band Multiphase Voltage-Controlled Oscillator in 0.18- μm CMOS

A multiphase oscillator suitable for 15/30-GHz dual-band applications is presented. In the circuit implementation, the 15-GHz half-quadrature voltage-controlled oscillator (VCO) is realized by a rotary traveling-wave oscillator, while frequency doublers are adopted to generate the quadrature output signals at the 30-GHz frequency band. The proposed circuit is fabricated in a standard 0.18-mum CMOS process with a chip area of 1.1times1.0 mm². Operated at a 2-V supply voltage, the VCO core consumes a dc power of 52 mW. With a frequency tuning range of 250 MHz, the 15-GHz half-quadrature VCO exhibits an output power of -8 dBm and a phase noise of -112 dBc/Hz at 1-MHz offset frequency. The measured power level and phase noise of the 30-GHz quadrature outputs are -16 dBm and -104 dBc/Hz, respectively     

A High-Performance CMOS Voltage-Controlled Oscillator for Ultra-Low-Voltage Operations

In this paper, a novel circuit topology of voltage-controlled oscillators (VCOs) suitable for ultra-low-voltage operations is presented. By utilizing the capacitive feedback and the forward-body-bias (FBB) technique, the proposed VCO can operate at reduced supply voltage and power consumption while maintaining remarkable circuit performance in terms of phase noise, tuning range, and output swing. Using a standard 0.18-mum CMOS process, a 5.6-GHz VCO is designed and fabricated for demonstration. Consuming a dc power of 3 mW from a 0.6-V supply voltage, the VCO exhibits a frequency tuning range of 8.1% and a phase noise of -118 dBc/Hz at 1-MHz offset frequency. With an FBB for the cross-coupled transistors, the fabricated circuit can operate at a supply voltage as low as 0.4 V. The measured tuning range and phase noise are 6.4% and -114 dBc/Hz, respectively     

频率覆盖3.2～6.1 GHz的CMOS LC VCO

通过提高MIM电容的调整范围,实现了一个覆盖3.2～6.1 GHz的CMOS LC VCO.该VCO使用0.18μm射频CMOS工艺制作,芯片面积约为1260μm×670μm.当输出5.5GHz时,VCO内核消耗功率为17.5mW;在100kHz频偏处的相位噪声是～101.67dBc/Hz.     

A 1.8-V 2.4/5.15-GHz dual-band LCVCO in 0.18-/spl mu/m CMOS technology

A dual band, fully integrated, low phase-noise and low-power LC voltage-controlled oscillator (VCO) operating at the 2.4-GHz industrial scientific and medical band and 5.15-GHz unlicensed national information infrastructure band has been demonstrated in an 0.18-/spl mu/m CMOS process. At 1.8-V power supply voltage, the power dissipation is only 5.4mW for a 2.4-GHz band and 8mW for a 5.15-GHz band. The proposed VCO features phase-noise of -135dBc/Hz at 3-MHz offset frequency away from the carrier frequency of 2.74GHz and -126dBc/Hz at 3-MHz offset frequency away from 5.49GHz. The oscillator is tuned from 2.2 to 2.85GHz in the low band (2.4-GHz band) and from 4.4 to 5.7GHz in the high band (5.15-GHz band).     

A wideband frequency synthesizer for a receiver application at multiple frequencies

An integer-N frequency synthesizer for a receiver application at multiple frequencies was implemented in 0.18 μm IP6M CMOS technology. The synthesizer generates 2.57 GHz, 2.52 GHz, 2.4 GHz and 2.25 GHz local signals for the receiver. A wide-range voltage-controlled oscillator (VCO) based on a reconfigurable LC tank with a binary-weighted switched capacitor array and a switched inductor array is employed to cover the desired frequencies with a sufficient margin. The measured tuning range of the VCO is from 1.76 to 2.59 GHz. From the carriers of 2.57 GHz,2.52 GHz, 2.4 GHz and 2.25 GHz, the measured phase noises are -122.13 dBc/Hz, -122.19 dBc/Hz, -121.8 dBc/Hz and -121.05 dBc/Hz, at 1 MHz offset, respectively. Their in-band phase noises are -80.09 dBc/Hz, -80.29 dBe/Hz,-83.05 dBc/Hz and -86.38 dBc/Hz, respectively. The frequency synthesizer including buffers consumes a total power of 70 Mw from a 2 V power supply. The chip size is 1.5 × 1 mm~2.     

A 1.8-2.6 GHz CMOS VCO with switched capacitor array and switched inductor array

The design of a 1.76-2.56 GHz CMOS voltage-controlled oscillator(VCO)with switched capacitor array and switched inductor array is presented.Fabricated in 0.18μm 1P6M CMOS technology,the VCO achieves a 37% frequency tuning range.The measured phase noise varies between-118.5 dBc/Hz and-122.8 dBc/Hz at 1 MHz offset across the tuning range.Power consumption is about 14.4 mW with a 1.8 V supply.Based on a reconfigurable LC tank with switched capacitor array and switched inductor array,the mnmg range is analyzed and derived in terms of design parameters,yielding useful equations to guide the circuit design.