Dielectric properties of a new ceramic system (1 − x)Mg4Nb2O9-xCaTiO3 at microwave frequency

The microstructures and the microwave dielectric properties of the (1 − x)Mg₄Nb₂O₉-xCaTiO₃ ceramic system were investigated. In order to achieve a temperature-stable material, CaTiO₃ (τ_f ∼ 800 ppm/°C) was chosen as a τ_f compensator and added to Mg₄Nb₂O₉ (τ_f ∼ −70 ppm/°C) to form a two phase system. It was confirmed by the XRD and EDX analysis. By appropriately adjusting the x-value in the (1 − x)Mg₄Nb₂O₉-xCaTiO₃ ceramic system, near-zero τ_f value can be achieved. A new microwave dielectric material, 0.5Mg₄Nb₂O₉-0.5CaTiO₃ applicable in microwave devices is suggested and possesses the dielectric properties of a dielectric constant ?_r ∼ 24.8, a Q × f value ∼82,000 GHz (measured at 9.1 GHz) and a τ_f value ∼−0.3 ppm/°C.     

Correlation of crystal structure and microwave dielectric properties for Zn(Ti1−xSnx)Nb2O8 ceramics

The correlation of crystal structure and microwave dielectric properties for Zn(Ti_1−xSn_x)Nb₂O₈ ceramics were investigated. The Zn(Ti_1−xSn_x)Nb₂O₈ ceramics contained ZnTiNb₂O₈ and an unknown Columbite-type phase. The columbite structure phase with increasing degree of ordering led to decrease of dielectric constant, increase of Qf and τ_f. The ZnTiNb₂O₈ with decreasing cation valence led to increase of τ_f. The typical values were: ? = 30.88, Qf = 43,500 GHz, τ_f = −54.32 × 10⁻⁶/ °C.     

Synthesis of (1 − x)Ca2/5Sm2/5TiO3-xLi1/2Nd1/2TiO3 ceramic powder via ethylenediaminetetraacetic acid precursor

(1 − x)Ca_2/5Sm_2/5TiO₃-xLi_1/2Nd_1/2TiO₃ (CSLNT) ceramic powder was prepared by a liquid mixing method using ethylenediaminetetraacetic acid (EDTA) as the chelating agent. TG, DTA, XRD and TEM characterized the precursors and derived oxide powders. When x = 0.3, perovskite CSLNT was synthesized at 1000 °C for 3 h in air. The CSLNT (x = 0.3) ceramics sintered at 1200 °C for 3 h show excellent microwave dielectric properties of ?_r = 99, Q_f = 6200 GHz and τ_f = 9 × 10⁻⁶ °C⁻¹.     

Synthesis, low-temperature sintering and the dielectric properties of the ZnO-(1 − x)TiO2-xSnO2 (x = 0.04-0.2)

ZnO-(1 − x)TiO₂-xSnO₂ (x = 0.04-0.2) ceramics were prepared by conventional mixed-oxide method combined with a chemical processing. Fine particle powders were prepared by chemical processing to activate the formation of compound and to improve the sinterability. One wt.% of V₂O₅ and B₂O₃ with the mole ratios of 3:1 were used to lower the sintering temperature of ceramics. The effect of Sn content on phase structure and dielectric properties were investigated. The results show that the substituting Sn for Ti accelerates the hexagonal phase transition to cubic phase, and an inverse spinel structure Zn₂(Ti_1−xSn_x)O₄ solid solution forms. The best dielectric properties obtained at x = 0.12. The ZnO-0.88TiO₂-0.12SnO₂ ceramics sintered at 900 °C exhibit a good dielectric property: ?_r = 29 and tan δ = 9.86 × 10⁻⁵. Due to their good dielectric properties, low firing characteristics, ZnO-(1 − x)TiO₂-xSnO₂ (x = 0.04-0.2) can serve as the promising microwave dielectric capacitor.     

Dielectric and pyroelectric anisotropy in melt-quenched BaBi2(Nb1 − xVx)2O9 ceramics

The (0 0 l) textured BaBi₂(Nb_1 − xV_x)₂O₉ (where x = 0, 0.03, 0.07, 0.1 and 0.13) ceramics were fabricated via the conventional melt-quenching technique followed by high temperature heat-treatment (800-1000 °C range). The influence of vanadium content and sintering temperature on the texture development and relative density were investigated. The samples corresponding to the composition x = 0.1 sintered at 1000 °C for 10 h exhibited the maximum orientation of about 67%. The Scanning electron microscopic studies revealed the presence of platy grains having the a-b planes perpendicular the pressing axis. The dielectric constant and the pyroelectric co-efficient values in the direction perpendicular to the pressing axis were higher. The anisotropy in the dielectric constant is about 100 (at 100 kHz) at the dielectric maximum temperature and anisotropy in the pyroelectric co-efficient is about 50 μC cm⁻² °C⁻¹ in the vicinity of pyroelectric anomaly for the sample corresponding to the composition x = 0.1 sintered at 1000 °C. Higher values of the dielectric loss and electrical conductivity were observed in the direction perpendicular to the pressing axis which is attributed to the high oxygen ion conduction in the a-b planes.     

Microwave dielectric properties and microstructures of the 11Li2O-3Nb2O5-12TiO2 ceramics with B2O3 addition

The effects of B₂O₃ addition, as a sintering agent, on the sintering behavior, microstructure and microwave dielectric properties of the 11Li₂O-3Nb₂O₅-12TiO₂ (LNT) ceramics have been investigated. With the low-level doping of B₂O₃ (≤2 wt.%), the sintering temperature of the LNT ceramic could be effectively reduced to 900 °C. The B₂O₃-doped LNT ceramics are also composed of Li₂TiO₃ss and “M-phase” phases. No other phase could be observed in the 0.5-2 wt.% B₂O₃-doped ceramics sintered at 840-920 °C. The addition of B₂O₃ induced no obvious degradation in the microwave dielectric properties but increased the τ_f values. Typically, the 0.5 wt.% B₂O₃-doped ceramics sintered at 900 °C have better microwave dielectric properties of ?_r = 49.2, Q × f = 8839 GHz, τ_f = 57.6 ppm/°C, which suggest that the ceramics could be applied in multilayer microwave devices requiring low sintering temperatures.     

Low loss Sr1−xCaxLa4Ti5O17 microwave dielectric ceramics

Microwave dielectric ceramics in the Sr_1−xCa_xLa₄Ti₅O₁₇ (0 ≤ x ≤ 1) composition series were prepared through a solid state mixed oxide route. All the compositions formed single phase ceramics within the detection limit of in-house X-ray diffraction when sintered in the temperature range 1450-1580 °C. Theoretical density and molar volume decreased due to the substitution of Ca²⁺ for Sr²⁺ which was associated with a decrease in the dielectric constant (?_r) and temperature coefficient of resonant frequency (τ_f) but an increase in quality factor, Qf_o. Optimum properties were achieved for Sr_0.4Ca_0.6La₄Ti₅O₁₇ which exhibited, ?_r ∼ 53.7, Qf_o ∼ 11,532 GHz and τ_f ∼ −1.4 ppm/°C.     

Microstructure and microwave dielectric characteristics of (1 − x)Ba(Zn1/3Ta2/3)O3-xBaTi4O9 ceramics

(1 − x)Ba(Zn_1/3Ta_2/3)O₃-xBaTi₄O₉ (0.1 ≤ x ≤ 0.85) composites are prepared by mixing 1150 °C-calcined BaTi₄O₉ with 1150 °C-calcined Ba(Zn_1/3Ta_2/3)O₃ powders. The crystal structure, microwave dielectric properties and sinterabilites of the (1 − x)Ba(Zn_1/3Ta_2/3)O₃-xBaTi₄O₉ ceramics have been investigated. X-ray diffraction patterns reveal that BaTi₄O₉, ordered and disordered Ba(Zn_1/3Ta_2/3)O₃ phases exist independently over the whole compositional range. The sintering temperatures of (1 − x)Ba(Zn_1/3Ta_2/3)O₃-xBaTi₄O₉ ceramics are about 1240 - 1320 °C and obviously lower than those of Ba(Zn_1/3Ta_2/3)O₃ ceramics. The dielectric constants (?_r) and the temperature coefficient of resonant frequency (τ_f) of (1 − x)Ba(Zn_1/3Ta_2/3)O₃-xBaTi₄O₉ ceramics increase with the increase of BaTi₄O₉ content. Nevertheless, the bulk densities and the quality values (Q × f) of (1 − x)Ba(Zn_1/3Ta_2/3)O₃-xBaTi₄O₉ ceramics increase with the increase of Ba(Zn_1/3Ta_2/3)O₃ content. The results are attributed to the higher density and quality value of Ba(Zn_1/3Ta_2/3)O₃ ceramics, the better grain growth, and the densification of sintered specimens added a small BaTi₄O₉ content. The (1 − x)Ba(Zn_1/3Ta_2/3)O₃-xBaTi₄O₉ ceramic with x = 0.1 sintered at 1320 °C exhibits a ?_r value of 31.5, a maximum Q × f value of 68500 GHz and a minimum τ_f value of 4.1 ppm/°C.     

Effect of Pb(Fe1/2Nb1/2)O3 modification on dielectric and piezoelectric properties of Pb(Mg1/3Nb2/3)O3-PbZr0.52Ti0.48O3 ceramics

10 mol% Pb(Fe_1/2Nb_1/2)O₃ (PFN) modified Pb(Mg_1/3Nb_2/3)O₃-PbZr_0.52Ti_0.48O₃ (PMN-PZT) relaxor ferroelectric ceramics with compositions of (0.9 − x)PMN-0.1PFN-xPZT (x = 0.1, 0.2, 0.3, 0.4, 0.5, 0.6, 0.7, 0.8 and 0.9) were prepared. X-ray diffraction investigations indicated that as-prepared ceramics were of pure perovskite phase and the sample with composition of x = 0.8 was close to morphotropic phase boundary (MPB) between rhombohedral and tetragonal phase. Dielectric properties of the as-prepared ceramics were measured, and the Curie temperature (T_c) increased sharply with increasing PZT content and could be higher than 300 °C around morphotropic phase boundary (MPB) area. At 1 kHz, the sample with composition of x = 0.1 had the largest room temperature dielectric constant ?_r = 3519 and maximum dielectric constant ?_m = 20,475 at T_m, while the sample with composition of x = 0.3 possessed the maximum dielectric relaxor factor of γ = 1.94. The largest d₃₃ = 318 pC/N could be obtained from as-prepared ceramics at x = 0.9. The maximum remnant polarization (P_r = 28.3 μC/cm²) was obtained from as-prepared ceramics at x = 0.4.     

Phase relations and microwave dielectric properties of vanadium modified Ba5Nb4O15 ceramics

Microwave dielectric ceramics of Ba₅Nb_4−xV_xO₁₅ (x = 0-1) were prepared by a solid-state reaction method. Vanadium substitution can markedly lower the sintering temperature of Ba₅Nb₄O₁₅ from 1450 to 1100 °C. The X-ray powder diffraction analysis reveals the multiphase nature of this system. A hexagonal-to-orthorhombic phase transition was also observed for the BaNb₂O₆ secondary phase. The microwave dielectric properties, such as τ_f, ε_r and Q × f value, decreased with increasing vanadium content for samples sintered at 1100 °C. There was an apparent increase in τ_f and Q × f value for samples (x ≥ 0.5) sintered at 1200 °C due to the hexagonal-to-orthorhombic phase transition of the BaNb₂O₆ phase. These results suggested that the microwave dielectric properties of multiphase ceramics strongly depended on the phase compositions and the phase transitions.     

Low-temperature firing and microwave dielectric properties of ZnO-Nb2O5-TiO2-SnO2 ceramics with CuO-V2O5

The effects of CuO-V₂O₅ addition on the sintering temperature and microwave dielectric properties of ZnO-Nb₂O₅-TiO₂-SnO₂ were investigated. The CuO-V₂O₅ addition lowered the sintering temperature of ZnO-Nb₂O₅-TiO₂-SnO₂ ceramics effectively from 1150 to 860 °C due to the liquid-phase effect of Cu₂V₂O₇ and Cu₃(VO₄)₂, as observed by XRD. The microwave dielectric properties were found to strongly correlate with the sintering temperature and the amount of CuO-V₂O₅ addition. The maximum Qf values decreased with increasing CuO-V₂O₅ content, due to the formation of the second phase, Cu₃(VO₄)₂ and CuNbO₃. Zero τ_f value can be obtained by properly adjusting the sintering temperature. At 860 °C, ZnO-Nb₂O₅-TiO₂-SnO₂ ceramics with 1.5 wt.% CuO-V₂O₅ gave excellent microwave dielectric properties: ?_r = 42.3, Qf = 9000 GHz and τ_f = 8 ppm/°C.     

Structural, spectroscopic and dielectric investigations on Ba8Zn(Nb6−xSbx)O24 microwave ceramics

Ba₈Zn(Nb_6−xSb_x)O₂₄ (x = 0, 0.3, 0.6, 0.9, 1.2, 1.5, 1.8 and 2.4) ceramics were prepared through the conventional solid-state route. The materials were calcined at 1250 °C and sintered in the range 1400-1425 °C. The structure of the system was analyzed by X-ray diffraction, Fourier transform infrared and Raman spectroscopic methods. The theoretical and experimental densities were calculated. The microstructure of the sintered pellets was analyzed using scanning electron microscopy. The low frequency dielectric properties were studied in the frequency range 50 Hz-2 MHz. The dielectric constant (?_r), temperature coefficient of resonant frequency (τ_f) and the unloaded quality factor (Q_u) are measured in the microwave frequency region using cavity resonator method. The τ_f values of the samples reduced considerably with the increase in Sb concentration. The materials have intense emission lines in the visible region. The compositions have good microwave dielectric properties and photoluminescence and hence are suitable for dielectric resonator and ceramic laser applications.     

Stoichiometric Pb(Mg1/3Nb2/3)O3 perovskite ceramics produced by reaction-sintering process

Stoichiometric lead magnesium niobate, Pb(Mg_1/3Nb_2/3)O₃ (PMN), perovskite ceramics produced by reaction-sintering process were investigated. Without calcination, a mixture of PbO, Nb₂O₅, and Mg(NO₃)₂ was pressed and sintered directly. Stoichiometric PMN ceramics of 100% perovskite phase were obtained for 1, 2, and 4 h sintering at 1250 and 1270 °C. PMN ceramics with density 8.09 g/cm³ (99.5% of theoretical density 8.13 g/cm³) and K_max 19,900 under 1 kHz were obtained.     

Study on properties of BaxSmyTi7O20 ceramics with CaO-SiO2-B2O3 glass

The effect of CaO-SiO₂-B₂O₃ (CSB) glass addition on the sintering temperature and dielectric properties of Ba_xSm_yTi₇O₂₀ ceramics has been investigated using X-ray diffraction, scanning electron microscopy and differential thermal analysis. The CSB glass starts to melt at about 970 °C, and a small amount of CSB glass addition to Ba_xSm_yTi₇O₂₀ ceramics can greatly decrease the sintering temperature from about 1350 to about 1260 °C, which is attributed to the formation of liquid phase. It is found that the dielectric properties of Ba_xSm_yTi₇O₂₀ ceramics are dependent on the amount of CSB glass and the microstructures of sintered samples. The product with 5 wt% CSB glass sintered at 1260 °C is optimal in these samples based on the microstructure and the properties of sintering product, when the major phases of this material are BaSm₂Ti₄O₁₂ and BaTi₄O₉. The material possesses excellent dielectric properties: ?_r = 61, tan δ = 1.5 × 10⁻⁴ at 10 GHz, temperature coefficient of dielectric constant is −75 × 10⁻⁶ °C⁻¹.     

Synthesis and microwave dielectric properties of Sr3Zn1−xMgxNb2O9 phases

Oxides of the type, Sr₃Zn_1−xMg_xNb₂O₉ (0≤x≤1) have been obtained by the ceramic method. These oxides crystallize in the hexagonal cell corresponding to ordered triple perovskites. Sintered disks show nearly frequency-independent dielectric constant for all the compositions. Compositions sintered at 1425°C yield dielectric constant of 20-22 at ∼6 GHz, with quality factor ranging from 1300 to 1500. Sr₃Zn_0.5Mg_0.5Nb₂O₉ shows a very low temperature coefficient of resonant frequency (τ_f) of +4 ppm/°C.     

Structure analysis on the Ba3Mg(Ta1−xNbx)2O9 ceramics: Coexistence of order and disorder

The Ba₃ZnTa₂O₉ (BZT) and Ba₃MgTa₂O₉ (BMT) ceramics, a family of A₃B²⁺B⁵⁺₂O₉ complex perovskites, are extensively utilized in mobile based technologies due to their intrinsic high unloaded quality factor, high dielectric constant and a low (near-zero) resonant frequency temperature coefficient at microwave frequencies. The preparation conditions as well as size and nature of B cations have a profound effect on the final dielectric properties. In this article, we report the effect of Nb⁵⁺ at the Ta⁵⁺ site on the BMT structure prepared at four synthesis temperatures (1300, 1400, 1500 and 1600 °C). The analysis has been carried out using the Rietveld technique on the X-ray powder diffraction data. Results suggest that both the preparation temperatures and Nb⁵⁺ content have significant effect on the ordering of B cations in the Ba₃Mg(Ta_1−xNb_x)₂O₉ solid solution. A disordered (cubic) structure is preferred by the 1300 °C compounds. The weight percentage of the ordered (trigonal) phase escalates, for a given composition, with increasing calcination temperature. A fully ordered trigonal arrangement exists only for x = 0.0 and 0.2 compounds calcined at 1600 °C, and the rest are biphasic (cubic and trigonal). The increase in the cubic fraction upon Nb⁵⁺ augmentation suggests that the solid solution leans more toward the disordered structural arrangement of B²⁺ and B⁵⁺ cations.     

Dielectric properties of B2O3-doped (1 − x)LaAlO3-xSrTiO3 ceramic system at microwave frequency

The effects of B₂O₃ addition on the microwave dielectric properties and the microstructures of (1−x)LaAlO₃-xSrTiO₃ ceramics prepared by conventional solid-state routes have been investigated. Doping with 0.25 wt.% B₂O₃ can effectively promote the densification and the microwave dielectric properties of (1−x)LaAlO₃-xSrTiO₃ ceramics. It is found that LaAlO₃-SrTiO₃ ceramics can be sintered at 1400°C due to the liquid phase effect of a B₂O₃ addition observed by scanning electronic microscopy (SEM). The dielectric constant as well as the Q×f value decreases with increasing B₂O₃ content. At 1460°C, 0.46LaAlO₃-0.54SrTiO₃ ceramics with 0.25 wt.% B₂O₃ addition possesses a dielectric constant (ε_r) of 35, a Q×f value of 38,000 (at 7 GHz) and a temperature coefficients of resonant frequency (τ_f) of −1 ppm/°C.     

Microwave dielectric properties of Ba2 − xSrxLa3Ti3NbO15 ceramics

High dielectric constant and low loss ceramics in the system Ba_2 − xSr_xLa₃Ti₃NbO₁₅ (x = 0-1) have been prepared by conventional solid-state ceramic route. Ba_2 − xSr_xLa₃Ti₃NbO₁₅ solid solutions adopted A₅B₄O₁₅ cation-deficient hexagonal perovskite structure for all compositions. The materials were characterized at microwave frequencies. They show a linear variation of dielectric properties with the value of x. Their dielectric constant varies from 48.34 to 43.03, quality factor Q_u × f from 20,291 to 39,088 GHz and temperature variation of resonant frequency from 8 to 1.39 ppm/°C as the value of x increases. These low loss ceramics might be used for dielectric resonator (DR) applications.     

Low temperature sintering and microwave dielectric properties of ZnTiNb2O8 ceramics with BaCu(B2O5) additions

The phases, microstructure and microwave dielectric properties of ZnTiNb₂O₈ ceramics with BaCu(B₂O₅) additions prepared by solid-state reaction method have been investigated using X-ray diffraction (XRD) and scanning electron microscopy (SEM). The pure ZnTiNb₂O₈ ceramic shows a high sintering temperature of about 1250 °C. However, it was found that the addition of BaCu(B₂O₅) lowered the sintering temperature of ZnTiNb₂O₈ ceramics from above 1250 °C to 950 °C due to the BCB liquid-phase. The results showed that the microwave dielectric properties were strongly dependent on densification, crystalline phases and grain size. Addition of 3 wt% BCB in ZnTiNb₂O₈ ceramics sintered at 950 °C afforded excellent dielectric properties of ?_r = 32.56, Q × f = 20,100 GHz (f = 5.128 GHz) and τ_f = −64.87 ppm/°C. These represent very promising candidates for LTCC dielectric materials.     

Ba3ZnTa2−xNbxO9 and Ba3MgTa2−xNbxO9 (0≤x≤1): synthesis, structure and dielectric properties

Oxides belonging to the families Ba₃ZnTa_2−xNb_xO₉ and Ba₃MgTa_2−xNb_xO₉ were synthesized by the solid state reaction route. Sintering temperatures of 1300°C led to oxides with disordered (cubic) perovskite structure. However, on sintering at 1425°C hexagonally ordered structures were obtained for Ba₃MgTa_2−xNb_xO₉ over the entire range (0≤x≤1) of composition, while for Ba₃ZnTa_2−xNb_xO₉ the ordered structure exists in a limited range (0≤x≤0.5). The dielectric constant is close to 30 for the Ba₃ZnTa_2−xNb_xO₉ family of oxides while the Mg analogues have lower dielectric constant of ∼18 in the range 50 Hz to 500 kHz. At microwave frequencies (5-7 GHz) dielectric constant increases with increase in niobium concentration (22-26) for Ba₃ZnTa_2−xNb_xO₉; for Ba₃MgTa_2−xNb_xO₉ it varies between 12 and 14. The “Zn” compounds have much higher quality factors and lower temperature coefficient of resonant frequency compared to the “Mg” analogues.