Preparation and electrochemical performance of Li-rich layered cathode material,Li[Ni<Subscript>0.2</Subscript>Li<Subscript>0.2</Subscript>Mn<Subscript>0.6</Subscript>]O<Subscript>2</Subscript>, for lithium-ion batteries

The Li-rich layered cathode material, Li[Ni_0.2Li_0.2Mn_0.6]O₂, was synthesized via a “mixed oxalate” method, and its structural and electrochemical properties were compared with the same material synthesized by the sol–gel method. X-ray diffraction (XRD) shows that the synthesized powders have a layered O₃–LiCoO₂-type structure with the R-3m symmetry. X-ray photoelectron spectroscopy (XPS) indicates that in the above material, Ni and Mn exist in the oxidation states of +2 and +4, respectively. The layered material exhibits an excellent electrochemical performance. Its discharge capacity increases gradually from the initial value of 228 mA hg⁻¹ to a stable capacity of over 260 mA hg⁻¹ after the 10th cycle. It delivers a larger capacity of 258 mA hg⁻¹ at the 30th cycle. The dQ/dV curves suggest that the increasing capacity results from the redox-reaction of Mn⁴⁺/Mn³⁺.     

Improved electrochemical properties of Li(Ni<Subscript>0.7</Subscript>Co<Subscript>0.3</Subscript>)O<Subscript>2</Subscript> cathode for lithium ion batteries with controlled sintering conditions

Improved electrochemical properties of Li(Ni_0.7Co_0.3)O₂ cathode material are reported. Samples were synthesized by the co-precipitation method with various sintering conditions, namely temperature, time and atmosphere. Li(Ni_0.7Co_0.3)O₂ sintered at 850 °C for 14 h in air exhibited the lowest unit cell volume accompanied with relatively higher values of c/a and I ₁₀₃/I ₁₀₄ reflection peaks ratios. This also exhibited superior electrochemical properties, such as high charge–discharge capacity, high Coulombic efficiency, and low irreversible capacity loss. This can be attributed to improved hexagonal ordering, crystallinity and morphology. The electrochemical cell parameters were better than the reported ones, probably due to controlled sintering conditions.     

Effect of molybdenum substitution on electrochemical performance of Li[Li0.2Mn0.54Co0.13Ni0.13]O2 cathode material

Molybdenum doping is introduced to improve the electrochemical performance of lithium-rich manganese-based cathode material. X-ray diffraction (XRD) results illustrate that the crystallographic parameters a, c and lattice volume V become larger with the increase of Mo content. The scanning electron microscope (SEM) shows that the molybdenum substitution increases the crystallinity of the primary particles. When evaluated as cathode material, the as-prepared Li[Li_0.2Mn_0.54-x/3Ni_0.13-x/3Co_0.13-x/3Mo_x]O₂ (x = 0.007) delivers a discharge capacity of 155.5 mA h g⁻¹ at 5 C (1 C = 250 mA g⁻¹) and exhibits the capacity retention of 81.8% at 1 C after 200 cycles. The results of cyclic voltammetry (CV) and electronic impedance spectroscopy (EIS) tests reflect that the molybdenum substitution is able to significantly reduce the electrode polarization and lower the charge-transfer resistance. Within appropriate amount of Mo doping, the lithium ion diffusion coefficient of the material can reach to 8.92 × 10^–15 cm² s⁻¹, which is ~ 30 times higher than that of pristine materials (2.65 × 10^–16 cm² s⁻¹).     

Improved electrochemical performance of Li1.2Ni0.2Mn0.6O2 cathode material for lithium ion batteries synthesized by the polyvinyl alcohol assisted sol-gel method

Li-rich Mn-based cathode materials (Li_1.2Ni_0.2Mn_0.6O₂) have been synthesized by a polyvinyl alcohol (PVA)-assisted sol-gel method. The influence of PVA content on the structure and electrochemical performance of Li_1.2Ni_0.2Mn_0.6O₂ has been investigated respectively. XRD results of the Li_1.2Ni_0.2Mn_0.6O₂ powders show that they exhibit similar XRD patterns as those of Li-rich Mn-based cathode materials, and the crystalline nature of the layered compound are improved by the presence of PVA. Physical characterizations indicate that the as-synthesized oxide is composed of uniform and separated particles compared to the larged aggregated ones of the product synthesized under the same condition but without PVA. As cathode for lithium ion battery, the material synthesized with 10% PVA exhibits not only a relatively high discharge capacity of 254.2 mA h g⁻¹, but also excellent rate performance and good cycling performance. EIS results show that the material synthesized with PVA decreases the charge-transfer resistance and enhances the reaction kinetics, which is considered to be the major factor for higher rate performance.     

Enhanced electrochemical performance of ZrO2 modified LiNi0.6Co0.2Mn0.2O2 cathode material for lithium ion batteries

LiNi_0.6Co_0.2Mn_0.2O₂ (NCM622) cathode has been modified by incorporating ZrO₂ nanoparticles to improve its electrochemical performance. Compared to the pristine electrode, the cycling stability and rate capability of 0.5 wt% ZrO₂ modified-NCM622 have been improved significantly. The 0.5 wt% ZrO₂ modified-NCM622 cathode shows a capacity retention of 83.8% after 100 cycles at 0.1 C between 2.8 and 4.3 V, while that of the pristine NCM622 electrode is only 75.6%. When the current rate is set as 5C, the capacity retention of the 0.5 wt% ZrO₂-modified NCM622 is 10% higher than that of the pristine NCM622. Also, the rate capability of 0.5 wt% ZrO₂-modified NCM622 is better than that of the pristine NCM622 at various C-rates in a voltage range of 2.8–4.3 V. The enhanced electrochemical performances of the ZrO₂-modified NCM622 cathodes can be attributed to their high Li-ion conductivity and structural stability.     

Enhanced electrochemical and storage properties of La2/3−XLi3XTiO3-coated Li[Ni0.4Co0.3Mn0.3]O2

A Li[Ni_0.4Co_0.3Mn_0.3]O₂ cathode was modified by applying a La_2/3−XLi_3XTiO₃ (LLT) coating. Transmission electron microscope (TEM) images reveal that the coating layer consists of nanoparticles. The coated cathode demonstrated an enhanced rate capability, discharge capacity, and cyclic performance than the uncoated cathode. However, the influence of the coating upon these electrochemical properties is highly dependent upon the composition of the LLT coating layer. Coating layers having high La and low Li contents, such as La_0.67TiO₃, effectively improved the rate capability of the cathode. However, coating layers with a low La and high Li content greatly enhanced the discharge capacity of the cathode under high cut-off voltage (4.8 V) conditions. Overall, the thermal stability of the Li[Ni_0.4Co_0.3Mn_0.3]O₂ electrode was improved by the LLT coating. Storage tests confirmed that the La_2/3−XLi_3XTiO₃ coating dramatically suppressed the dissolution of transition metals into the electrolyte.     

Structure and electrochemical characterization of LiNi<Subscript>0.3</Subscript>Co<Subscript>0.3</Subscript>Mn<Subscript>0.3</Subscript>Fe<Subscript>0.1</Subscript>O<Subscript>2</Subscript> cathode for lithium secondary battery

A lithium insertion material having the composition LiNi_0.3Co_0.3Mn_0.3Fe_0.1O₂ was synthesized by simple sol-gel method. The structural and electrochemical properties of the sample were investigated using X-ray diffraction spectroscopy (XRD) and the galvanostatic charge-discharge method. Rietvelt analysis of the XRD patterns shows that this compound can be classified as α-NaFeO₂ structure type (R3m; a=2.8689(5) Å and 14.296(5) Å in hexagonal setting). Rietvelt fitting shows that a relatively large amount of Fe and Ni ion occupy the Li layer (3a site) and a relatively large amount of Li occupies the transition metal layer (3b site). LiNi_0.3Co_0.3Mn_0.3Fe_0.1O₂ when cycled in the voltage range 4.3–2.8 V gives an initial discharge capacity of 120 mAh/g, and stable cycling performance. LiNi_0.3Co_0.3Mn_0.3Fe_0.1O₂ in the voltage range 2.8–4.5 V has a discharge capacity of 140 mAh/g, and exhibits a significant loss in capacity during cycling. Ex-situ XRD measurements were performed to study the structure changes of the samples after cycling between 2.8–4.3 V and 2.8–4.5 V for 20 cycles. The XRD and electrochemical results suggested that cation mixing in this layered structure oxide could be causing degradation of the cell capacity.     

Effects of nitrogen and sulfur atom regulation on electrochemical properties of Na3V2(PO4)2F3 cathode material for Na-ion batteries

The cathode material Na₃V₂(PO₄)₂F₃ of sodium-ion battery is well-known for its large number of ion migration channels and high working voltage. However, the electrochemical performance of Na₃V₂(PO₄)₂F₃ is not very outstanding. Thus, in the present study, Na₃V₂(PO₄)₂F₃ cathode materials were successfully synthesized by using the sol-gel method and mechanical milling method to enhance the electrochemical performance. The physicochemical properties of synthesized Na₃V₂(PO₄)₂F₃ were investigated by using X-ray diffraction spectroscopy, X-ray photoelectron spectroscopy, scanning electron microscopy, transition electron microscopy. X-ray diffraction spectroscopy indicates that the doping of nitrogen and sulfur did not alter the crystal form of Na₃V₂(PO₄)₂F₃. Transition electron microscopy image shows that Na₃V₂(PO₄)₂F₃ has a thin carbon layer, and x-ray photoelectron spectroscopy illustrates the successful doping of nitrogen and sulfur into the carbon layer. The cyclic voltammetry curves show that the nitrogen and sulfur co-doped Na₃V₂(PO₄)₂F₃ samples have good reversibility and low polarization. Materials with 15% thiourea has a high discharge specific capacity (126.9 mA h g^?1 at 0.2 C) at the first cycle and excellent cycle stability (126.3 mA h g^?1 after 100 cycles, a capacity retention of 99.5%) among the synthesized cathode materials. In the present study, the electrochemical performance of the Na₃V₂(PO₄)₂F₃ cathode material was enhanced by regulation of co-doping of nitrogen and sulfur atoms.     

Comparative study of the preparation and electrochemical performance of LiNi<Subscript>1</Subscript><Subscript>/2</Subscript>Mn<Subscript>1/2</Subscript>O<Subscript>2</Subscript> electrode material for rechargeable lithium batteries

Positive electrode material LiNi_1/2Mn_1/2O₂ was synthesized via the carbonate co-precipitation method and the hydroxide precipitation route to study the effects of the precursor on its structural and electrochemical properties. The results of X-ray diffraction and Rietveld refinement show that the carbonate precursor of Ni²⁺ and Mn²⁺ exhibits one phase at a pH of 8.5, while the hydroxide deposit separates into Ni(OH)₂ and Mn(OH)₂ phases under the same experimental conditions. LiNi_1/2Mn_1/2O₂ material prepared from the hydroxide precursor shows 8.9% Li/Ni exchange and a large capacity loss of 11.3% in the first 10 cycles. By contrast, more uniform distribution of transition metal ions and stable Mn²⁺ in the carbonate precursor contribute to only 7.8% Li/Ni disorder in the obtained LiNi_1/2Mn_1/2O₂, which delivers a reversible capacity of about 182 mAh g⁻¹ at a current rate of 14 mA g⁻¹ between 2.5 and 4.8 V.     

Cr掺杂对富锂锰基正极材料Li1.2Ni0.2Mn0.6O2结构和电化学性能的影响

采用共沉淀-高温固相合成法制备锂离子电池正极材料Li_1.2Ni_0.2Mn_0.2-x/2Mn_0.6-x/2Cr_xO₂（x=0,0.04,0.08,0.12）。利用X射线衍射（XRD）、扫描电镜（SEM）、恒电流充放电测试和电化学交流阻抗谱（EIS）对掺杂不同Cr含量的正极材料的结构、形貌和电化学性能进行分析测试。结果表明：制备出的Li_1.2Ni_0.2Mn_0.2-x/2Mn_0.6-x/2Cr_xO₂正极材料均具备层状固溶体结构。Cr掺杂不会改变材料的结构,而且能够有效抑制循环过程中材料由层状向尖晶石结构转变的过程。当Cr的掺杂量为8%（即x=0.08）时,得到的正极材料Li_1.2Ni_0.16Mn_0.56Cr_0.08O₂具有最好的电化学性能。0.1C的首次放电比容量由未掺杂的230.4 mA·h·g^-1增加到246.6 mA·h·g^-1,在0.2C电流下50次循环后的容量保持率由93.5%提高至95.36%,5C的放电比容量由91.5 mA·h·g^-1增加到104.2 mA·h·g^-1。而且x=0.08时制备的样品具有最小的电荷转移阻抗。     

Synthesis and Characterization of Cobalt-Doped WS<Subscript>2</Subscript> Nanorods for Lithium Battery Applications

Cobalt-doped tungsten disulfide nanorods were synthesized by an approach involving exfoliation, intercalation, and the hydrothermal process, using commercial WS₂ powder as the precursor and n-butyllithium as the exfoliating reagent. XRD results indicate that the crystal phase of the sample is 2H-WS₂. TEM images show that the sample consists of bamboo-like nanorods with a diameter of around 20 nm and a length of about 200 nm. The Co-doped WS₂ nanorods exhibit the reversible capacity of 568 mAh g⁻¹ in a voltage range of 0.01–3.0 V versus Li/Li⁺. As an electrode material for the lithium battery, the Co-doped WS₂ nanorods show enhanced charge capacity and cycling stability compared with the raw WS₂ powder.     

Synthesis,structural, and electrochemical performance of V<Subscript>2</Subscript>O<Subscript>5</Subscript> nanotubes as cathode material for lithium battery

Various vanadium oxide nanostructures are currently drawn interest for the potential applications of Li batteries, super capacitors, and electrochromic display devices. In this article, the synthesis of V₂O₅ nanotubes by hydrothermal method using 1-hexadecylamine (HDA) and PEO as a template and surface reactant were reported, respectively. The structural properties and electrochemical performances of these nanostructures were investigated for the application of Li batteries. Structure and morphology of the samples were investigated by XRD, FTIR, SEM, and TEM analysis. The battery with V₂O₅ nanotubes electrode showed initial specific capacity of 185 mAhg⁻¹, whereas the PEO surfactant V₂O₅ nanotubes exhibited 142 mAhg⁻¹. It was found that PEO surfactant V₂O₅ nanotubes material showed less specific capacity at initial stages but better stability was exhibited at higher cycle numbers when compared to that of V₂O₅ nanotubes. The cyclic performance of the PEO surfactant material seems to be improved with the role of polymeric component due to its surface reaction with V₂O₅ nanotubes during the hydrothermal process.     

Catalytic properties of Co<Subscript>3</Subscript>O<Subscript>4</Subscript> nanoparticles for rechargeable Li/air batteries

Three types of Co₃O₄ nanoparticles are synthesized and characterized as a catalyst for the air electrode of a Li/air battery. The shape and size of the nanoparticles are observed using scanning electron microscopy and transmission electron microscopy analyses. The formation of the Co₃O₄ phase is confirmed by X-ray diffraction. The electrochemical property of the air electrodes containing Co₃O₄ nanoparticles is significantly associated with the shape and size of the nanoparticles. It appears that the capacity of electrodes containing villiform-type Co₃O₄ nanoparticles is superior to that of electrodes containing cube- and flower-type Co₃O₄ nanoparticles. This is probably due to the sufficient pore spaces of the villiform-type Co₃O₄ nanoparticles.     

Study of electrochemical properties and the charge/discharge mechanism for Li<Subscript>4</Subscript>Mn<Subscript>5</Subscript>O<Subscript>12</Subscript>/MnO<Subscript>2</Subscript>-AC hybrid supercapacitor

Spinel Li₄Mn₅O₁₂ was prepared by a sol–gel method. The manganese oxide and activated carbon composite (MnO₂-AC) were prepared by a method in which KMnO₄ was reduced by activated carbon (AC). The products were characterized by XRD and FTIR. The hybrid supercapacitor was fabricated with Li₄Mn₅O₁₂ and MnO₂-AC, which were used as materials of the two electrodes. The pseudocapacitance performance of the Li₄Mn₅O₁₂/MnO₂-AC hybrid supercapacitor was studied in various aqueous electrolytes. Electrochemical properties of the Li₄Mn₅O₁₂/MnO₂-AC hybrid supercapacitor were studied by using cyclic voltammetry, electrochemical impedance measurement, and galvanostatic charge/discharge tests. The results show that the hybrid supercapacitor has electrochemical capacitance performance. The charge/discharge test showed that the specific capacitance of 51.3 F g⁻¹ was obtained within potential range of 0–1.3 V at a charge/discharge current density of 100 mA g⁻¹ in 1 mol L⁻¹ Li₂SO₄ solution. The charge/discharge mechanism of Li₄Mn₅O₁₂ and MnO₂-AC was discussed.     

Properties of LiNi<Subscript>0.8</Subscript>Co<Subscript>0.1</Subscript>Mn<Subscript>0.1</Subscript>O<Subscript>2</Subscript> as a high energy cathode material for lithium-ion batteries

Nickel-rich layered materials are prospective cathode materials for use in lithium-ion batteries due to their higher capacity and lower cost relative to LiCoO₂. In this work, spherical Ni_0.8Co_0.1Mn_0.1(OH)₂ precursors are successfully synthesized through a co-precipitation method. The synthetic conditions of the precursors - including the pH, stirring speed, molar ratio of NH₄OH to transition metals and reaction temperature - are investigated in detail, and their variations have significant effects on the morphology, microstructure and tap-density of the prepared Ni_0.8Co_0.1Mn_0.1 (OH)₂ precursors. LiNi_0.8Co_0.1Mn_0.1O₂ is then prepared from these precursors through a reaction with 5% excess LiOH· H₂O at various temperatures. The crystal structure, morphology and electrochemical properties of the Ni_0.8Co_0.1Mn_0.1 (OH)₂ precursors and LiNi_0.8Co_0.1Mn_0.1O₂ were investigated. In the voltage range from 3.0 to 4.3 V, LiNi_0.8Co_0.1Mn_0.1O₂ exhibits an initial discharge capacity of 193.0mAh g^-1 at a 0.1 C-rate. The cathode delivers an initial capacity of 170.4 mAh g^-1 at a 1 C-rate, and it retains 90.4% of its capacity after 100 cycles.     

Synthesis and electrochemical properties of layered LiNi<Subscript>1/2</Subscript>Mn<Subscript>1/2</Subscript>O<Subscript>2</Subscript>prepared by coprecipitation

Spherical LiNi_1/2Mn_1/2O ₂ powders were synthesized from LiOH . H₂O and coprecipitated metal hydroxide, (Ni_1/2Mn_1/2)(OH)₂. The average particle size of the powders was about 10 m and the size distribution was quite narrow due to the homogeneity of the metal hydroxide, (Ni_1/2Mn_1/2)(OH)₂. The tap-density of the LiNi_1/2Mn_1/2O₂ powders was approximately 2.2 g cm_–3, which is comparable to the tap-density of commercial LiCoO₂. The LiNi_1/2Mn_1/2 O₂electrode delivered a discharge capacity of 152, 163, 183, and 189 mA h g^–1 in the voltage ranges of 2.8–4.3, 2.8–4.4, 2.8–4.5, and 2.8–4.6 V, respectively, with good cyclability. Furthermore, Al(OH)₃-coated LiNi_1/2Mn_1/2O₂exhibited excellent cycling behavior and rate capability compared to the pristine electrode.