Cr-doped TiO2 thin films deposited by RF-sputtering

Cr-doped TiO₂ thin films with different band gaps were prepared. Higher Cr doping was beneficial to the formation of the rutile-TiO₂ phase over the anatase-TiO₂ phase. A 4.8% Cr-doped thin film indicated a band gap of 2.95 eV, which was lower than the band gap of the rutile-TiO₂. Cr doping was accompanied by the formation of not only the rutile-TiO₂ phase but also the Cr₂O₃ phase, lead to the degradation of the hydrophilicity. The TiO₂ thin films with the mixed phase were not desirable to improve the hydrophilicity.     

The gas sensitivity of nano TiO2-SnO2 film doped with Cd(II) ion

The nanocomposite oxide (0.2TiO₂-0.8SnO₂) doped with Cd²⁺ powder have been prepared and characterized by XRD and their gas-sensing sensitivity were characterized using gas sensing measurement. Experimental results show that, bicomponent nano anatase TiO₂ and rutile SnO₂ particulate thick film doped with Cd²⁺ behaves with good sensitivity to formaldehyde gas of 200 ppm in the air, and the optimum sensing temperature was reduced from 360 °C to 320 °C compared with the undoped Cd²⁺ thick film. The gas sensing thick films doped with Cd²⁺ also show good selectivity to formaldehyde among benzene, toluene, xylene and ammonia as disturbed gas and could be effectively used as an indoor formaldehyde sensor.     

Superhydrophilic anatase TiO2 film with the micro- and nanometer-scale hierarchical surface structure

Nanosized anatase TiO₂ film on the ITO glass has been fabricated via spin coat process, with sodium dodecylbenzenesulfonate modified TiO₂ nanoparticles, which is synthesized by a sol-hydrothermal method, and also characterized mainly by means of field emission scanning electron microscopy (FESEM). The results show that the as-prepared anatase TiO₂ film exhibits superhydrophilic characteristic although it is not exposed to ultraviolet irradiation. The high roughness resulting from hierarchical surface structure is responsible for its superhydrophilicity. This work would provide a new route to fabricate newly nanostructured semiconductor films.     

TiO2-SnO2 system for gas sensing—Photodegradation of organic contaminants

Catalytic photodegradation of organic contaminants by means of UV light has been demonstrated for gas sensors based on composites of TiO₂-SnO₂. Thin film resistive-type gas sensors of TiO₂-SnO₂ have been deposited at 350 °C by RF sputtering from a Ti-SnO₂ target with varying surface ratio of SnO₂/Ti. Photodegradation experiments of bromothymol blue by UV light have been performed by means of the optical spectrophotometry over the wavelength range extending from 300 nm to 600 nm. The influence of the UV illumination on the sensor response to 100-20,000 ppm of H₂ has been investigated in situ on motor oil contaminated sensors. It has been found that sequential exposures to UV light lead to a partial recovery of the sensor signal to hydrogen.     

Pt纳米颗粒负载SrTiO3/TiO2异质结结构制备及制氢性能

本文以固定n(Sr)/n(Ti)摩尔比0.4的SrTiO_3/TiO_2(金红石相)异质结纳米颗粒,通过"光催化还原沉积方法"制备不同质量分数的纳米铂颗粒(0、1%、2%、5%),探究其催化活性的变化,采用XRD、SEM、UV-vis、XPS方法对其进行表征,并做了相关光催化分解水产氢性能测试.结果表明:负载贵金属Pt纳米颗粒量越大,对应的Pt晶粒平均尺寸为40.8 nm,1%Pt纳米颗粒SrTiO_3/TiO_2异质结构的BET比表面积在23.195 m~2/g处最高,并且介孔材料的特征是平均Barrett-Joyner-Halenda(BJH)孔径为13.60 nm,总孔体积为0.079 cm~3/g;高BET表面积和大的总孔体积强烈地支持SrTiO_3/TiO_2具有介孔结构的事实;相应的催化剂催化活性越高,其中负载5%Pt纳米颗粒的SrTiO_3/TiO_2纳米颗粒光催化8 h产氢量为3.574 mmol,平均产氢效率为0.447 mmol/(gcat·h),但从性价比的角度来考虑,其催化效率远不及负载1%Pt纳米颗粒的SrTiO_3/TiO_2纳米颗粒催化效率的5倍,因此负载5%Pt的SrTiO_3/TiO_2纳米颗粒光催化效率最高.     

Photo-fixation of SO2 in nanocrystalline TiO2 films prepared by reactive DC magnetron sputtering

We report on photo-fixation of SO₂ onto nanostructured TiO₂ thin films prepared by reactive DC magnetron sputtering. The films were exposed to 50 ppm SO₂ gas mixed in synthetic air and illuminated with UV light at 298 and 473 K. The evolution of the adsorbed SO_x species was monitored by in situ Fourier transform infrared specular reflection spectroscopy. Significant photo-fixation occurred only in the presence of UV illumination. The SO₂ uptake was dramatically enhanced at elevated temperatures and then produced strongly bonded surface-coordinated SO_x complexes. The total SO_x uptake is consistent with Langmuir adsorption kinetics. The sulfur doping at saturation was estimated from X-ray photoelectron spectroscopy to be ~ 2.2 at.% at 473 K. These films were pale yellowish and had an optical absorption coefficient being ~ 3 times higher than in undoped film. The S-doped films exhibit interesting oleophobic properties, exemplified by the poor adherence of stearic acid. Our results suggest a new method for sulfur doping of TiO₂ to achieve combined anti-grease and photocatalytic properties.     

A study of textured non-stoichiometric MoTe2 thin films used as substrates for textured stoichiometric MoS2 thin films

Textured MoTe₂ films have been prepared by sequential evaporation of the constituents followed by annealing under a tellurium pressure. The films are systematically textured with the c-axis of the crystallites perpendicular to the plane of substrate, however, the film composition is difficult to control and even after process optimization the films are tellurium deficient. This is thought to be caused by the electro negativity difference of the constituents.The textured MoTe₂ films have been used as substrates on which to grow MoS₂ films by annealing under a pressure of sulfur that allows textured MoS₂ films to be grown with good crystalline properties. The presence of sulfur at the surface and annealing under dynamic vacuum is important for this process and moreover, suppresses the superficial oxidation of the Mo and Te constituents.     

Natural and persistent superhydrophilicity of SiO2/TiO2 and TiO2/SiO2 bi-layer films

Sol-gel SiO₂/TiO₂ and TiO₂/SiO₂ bi-layer films have been deposited from a polymeric SiO₂ solution and either a polymeric TiO₂ mother solution (MS) or a derived TiO₂ crystalline suspension (CS). The chemical and structural properties of MS and CS bi-layer films heat-treated at 500 °C have been investigated by Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and transmission electron microscospy. Water contact angle measurements show that MS SiO₂/TiO₂ and CS TiO₂/SiO₂ bi-layer films exhibit a natural superhydrophilicity, but cannot maintain a zero contact angle for a long time over film aging. In contrast, CS SiO₂/TiO₂ bi-layer films exhibit a natural, persistent, and regenerable superhydrophilicity without the need of UV light. Superhydrophilic properties of bi-layer films are discussed with respect to the nature of the TiO₂ single-layer component and arrangement of the bi-layer structure, i.e. TiO₂ underlayer or overlayer.     

Novel photocatalytic TiO2 coatings produced by HVOF thermal spraying process

Titanium dioxide coatings were deposited by high velocity oxy-fuel spraying (HVOF) using agglomerated nano-powders. Different spraying parameters were used to determine their influences on the crystallite structure and photocatalytic performance of the coatings. The as-sprayed TiO₂ coatings were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). Photocatalytic efficiency of the elaborated samples was evaluated from the conversion rate of ethanol. A high anatase content of 80% by volume was achieved for the coating deposited by a 120 ml/min fuel flow rate. The results show that the as-sprayed TiO₂ HVOF coatings were highly photocatalytically reactive for the degradation of ethanol.     

Influence of metal plasma ion implantation on photo-sensitivity of anatase TiO2 thin films

Nano-scale TiO₂ thin films were synthesized by using sol-gel and spin-coating techniques on glass substrates for photo-catalytic applications. The Ti(IV) butoxide-based TiO₂ thin films were optimized for transforming into the high-purity crystalline anatase phase when calcined at 500 °C. To further enhance the photo-catalysis sensitivity of TiO₂ thin films for use in visible light environments, a metal plasma ion implantation process was implemented to modify the band gap electron configuration of Ti. Various transition metal atoms such as Ni, Cu, V, and Fe were ionized and accelerated at 20 keV to impinge on the surface of TiO₂ substrates at a dosage of 5 × 10¹⁵ ions/cm². ESCA analysis confirmed the binding energy shift of Ti by 0.8-1.2 eV, which accounted for the increased effective positive charge of Ti, resulting in more effective electron trapping capability and, thus, the electron-hole pair separation. In addition, the absorption spectroscopy demonstrated that optical absorption in the visible light regime occurred in specimens implanted with transition metal ions, likely due to the formation of extra impurity energy levels within the original TiO₂ band gap energy structure. Among all tested implant materials, the band gap energy of TiO₂ was effectively reduced by Cu and Fe ion implantation by 0.9-1.0 eV, which was sufficient enough to excite valence electrons over the band gap in visible light environments. The feasibility of the metal-doped TiO₂ thin films for effective applications under visible light irradiation was further confirmed by using super-hydrophilicity contact-angle measurement.     

One-pot synthesis of intestine-like SnO2/TiO2 hollow nanostructures

In the present study the intestine-like binary SnO₂/TiO₂ hollow nanostructures are one-pot synthesized in aqueous phase at room temperature via a colloid seeded deposition process in which the intestine-like hollow SnO₂ spheres and Ti(SO₄)₂ are used as colloid seeds and Ti-source, respectively. The novel core (SnO₂ hollow sphere)-shell (TiO₂) nanostructures possess a large surface area of 122 m²/g (calcined at 350 °C) and a high exposure of TiO₂ surface. The structural change of TiO₂ shell at different temperatures was investigated by means of X-ray diffraction and Raman spectroscopy. It was observed that the rutile TiO₂ could form even at room temperature due to the presence of SnO₂ core and the unique core-shell interaction.     

Single-step sputtered Cu2SnSe3 films using the targets composed of Cu2Se and SnSe2

Cu₂SnSe₃ thin films were prepared by single-step D.C. sputtering at 100-400 °C for 3 h using targets composed of Cu₂Se and SnSe₂ in three different ratios of 2/1 (target A), 1.8/1 (target B), and 1.6/1 (target C). The advantages of self-synthesized SnSe₂ instead of commercially available SnSe for depositing Cu₂SnSe₃ thin films were demonstrated. Effects of target composition and substrate temperature on the properties of Cu₂SnSe₃ thin films were investigated. Structure, surface morphology, composition, electrical and optical properties at different process conditions were measured. The 400 °C-sputtered films obtained from target B display with direct band gap of 0.76 eV, electrical resistivity of 0.12 Ω cm, absorption coefficient of 10⁴-10⁵ cm^− 1, carrier concentration of ∼ 1.8 × 10¹⁹ cm^− 3, and electrical mobility of 2.9 cm²/V s.     

In-situ preparation of TiO2/SnO2 nanocrystalline sol for photocatalysis

A novel preparation method to synthesize TiO₂/SnO₂ nanocrystalline sol under mild conditions was presented. Ti(OC₄H₉)₄ used as a precursor was hydrolyzed in the rutile SnO₂ nanocrystalline sol, and in-situ formed TiO₂/SnO₂ nanocrystalline sol. The crystal structure, morphology and photocatalysis performance of samples were investigated. The results show that the additional rutile SnO₂ nano grains serve as heterogeneous crystal nucleus and exhibite the inducing effect on TiO₂ grains growth, thus leading to the changes in crystalline phase and particle morphology. In addition, the photoluminescence (PL) spectra analysis indicates that TiO₂/SnO₂ composite structure induces a better charge separation, and thus the photocatalytic activity of TiO₂/SnO₂ sol is increased significantly compared with TiO₂ sol.     

Effect of TiO2-SiO2 sol-gel coating on the cpTi-porcelain bond strength

The effects of TiO₂-SiO₂ sol-gel coating with different firing temperatures (300 °C, 500 °C, and 750 °C) on the cpTi-porcelain bond strength were investigated in the present study. Prior to applying the low-fusing dental titanium porcelain, the phase, surface morphology, surface roughness and static water contact angle of the intermediate layer were evaluated. The cpTi-porcelain bond strength was measured using the three-point flexure test according to ISO 9693 standard. Statistical analyses were made using one-way ANOVA and Dunnett-t test. Significantly higher bond strength of TiO₂-SiO₂/750 °C (specimens coated with TiO₂-SiO₂ sol-gel coating and fired at 750 °C for 1 h) when compared to the control group was observed (p < 0.05). No rutile phase was found in all the tested specimens coated with TiO₂-SiO₂ sol-gel coating. The surface morphology of the intermediate layer was apparently different with different firing temperatures. It was found that the static water contact angle of TiO₂-SiO₂/750 °C significantly decreased (p < 0.05). However, no markedly different R_a of TiO₂-SiO₂/500 °C and TiO₂-SiO₂/750 °C in comparison to that of the control group was observed (p > 0.05). The results show that the TiO₂-SiO₂ sol-gel coating fired at 750 °C for 1 h can notably improve the cpTi-porcelain bond strength and may be suitable for clinical use.     

Atomic layer deposited TiO2 for implantable brain-chip interfacing devices

In this paper we investigated atomic layer deposition (ALD) TiO₂ thin films deposited on implantable neuro-chips based on electrolyte-oxide-semiconductor (EOS) junctions, implementing both efficient capacitive neuron-silicon coupling and biocompatibility for long-term implantable functionality.The ALD process was performed at 295 °C using titanium tetraisopropoxide and ozone as precursors on needle-shaped silicon substrates. Engineering of the capacitance of the EOS junctions introducing a thin Al₂O₃ buffer layer between TiO₂ and silicon resulted in a further increase of the specific capacitance. Biocompatibility for long-term implantable neuroprosthetic systems was checked upon in-vitro treatment.     

Structural engineering of thin films of vertically aligned TiO2 nanorods

Self-assembled and vertically aligned rutile titania nanorods and thin films with a preferred [002] axial orientation were grown on substrates of fluorine-doped tin dioxide, using a hydrothermal method. Each nanorod was made of a bundle of densely packed and ultra fine nano-fibers growing along the [002] direction. The results show that ethanol substitution of water as solvent is highly effective in promoting the one-dimensional growth of the rutile nanorods and increasing their packing density in the thin films, which offers a simple-but-effectual leverage to monitor the nanorod structures for varied applications.     

Characterization of sol-gel derived TiO2/ZrO2 films and powders by Raman spectroscopy

The effect of zirconium dioxide addition on crystal structure of sol-gel TiO₂ mesoporous films and powders has been investigated by means of Raman spectroscopy, X-Ray diffraction, and Atomic force microscopy. Zirconium incorporation (up to 30 mol%) into TiO₂ lattice resulted in the formation of Ti_1 − xZr_xO₂ solid solution with anatase structure for the binary powders has been proved. Appearance of tetragonal ZrO₂ phase was observed for the samples with high zirconium content.     

Structural, thermal and optical characterization of TiO2:ZrO2 thin films prepared by sol-gel method

We have studied the structural and optical properties of thin films of TiO₂, doped with 5% ZrO₂ and deposited on glass substrate (by the sol-gel method). The dip-coated thin films have been examined at different annealing temperatures (350 to 450 °C) and for various layer thicknesses (63-286 nm). Refractive index and porosity were calculated from the measured transmittance spectrum. The values of the index of refraction are in the range of 1.62-2.29 and the porosity is in the range of 0.21-0.70. The coefficient of transmission varies from 50 to 90%. In the case of the powder of TiO₂, doped with 5% ZrO₂, and aged for 3 months in ambient temperature, we have noticed the formation of the anatase phase (tetragonal structure with 14.8 nm grains). However, the undoped TiO₂ exhibits an amorphous phase. After heat treatments of thin films, titanium oxide starts to crystallize at the annealing temperature 350 °C. The obtained structures are anatase and brookite. The calculated grain size, depending on the annealing temperature and the layer thickness, is in the range (8.58-20.56 nm).     

Preparation of CuAlO2 and CuCrO2 thin films by sol-gel processing

CuAlO₂ and CuCrO₂ thin films were prepared by sol-gel processing and subsequent thermal treatment in air and inert gas atmosphere. Resistivities of 700 Ω cm and 60 Ω cm with optical transmissions of 65% and 32% were achieved respectively. The crystallization temperature of 700 °C allows the preparation of CuCrO₂ on borosilicate glass. P-type conductivity was verified by Seebeck measurements and a transparent heterostructure including p-CuCrO₂ showed rectifying behavior.     

Nanoporous TiO2 thin film based conductometric H2 sensor

Nanoporous titanium dioxide (TiO₂) based conductometric sensors have been fabricated and their sensitivity to hydrogen (H₂) gas has been investigated. A filtered cathodic vacuum arc (FCVA) system was used to deposit ultra-smooth Ti thin films on a transducer having patterned inter-digital gold electrodes (IDTs). Nanoporous TiO₂ films were obtained by anodization of the titanium (Ti) thin films using a neutral 0.5% (wt) NH₄F in ethylene glycol solution at 5 V for 1 h. After anodization, the films were annealed at 600 °C for 8 h to convert the remaining Ti into TiO₂. The scanning electron microscopy (SEM) images revealed that the average diameters of the nanopores are in the range of 20 to 25 nm. The sensor was exposed to different concentrations of H₂ in synthetic air at operating temperatures between 100 °C and 300 °C. The sensor responded with a highest sensitivity of 1.24 to 1% of H₂ gas at 225 °C.