Structural transformation and magnetic properties of CaMn1 − xFexO3 − δ (0.0 ≤ x ≤ 0.5)

We have investigated the structural and magnetic properties of CaMn_1 − xFe_xO_3 − δ (0.0 ≤ x ≤ 0.5). Solid state method is used for the synthesis of these samples. Sintering of these compositions at 1300 °C stabilizes higher ionic radii Fe^+ 3 (0.645 Å) at Mn^+ 4 (0.53 Å) site in CaMn_1 − xFe_xO_3 − δ. Structural transformation from orthorhombic to tetragonal to pseudo cubic crystal system and the increase in lattice parameters have been observed with the substitution of Fe at Mn site in CaMn_1 − xFe_xO_3 − δ (0.0 ≤ x ≤ 0.5). The magnetization data show the transformation of G type of antiferromagnetic arrangement of Mn^+ 4 electrons spins in CaMnO₃ into paramagnetic spin type arrangement with the substitution of Fe at Mn site. The compositions x = 0.05, x = 0.1and x = 0.2 show a small kink ~ 100 K in the magnetization data, which resulted due to the competition between antiferromagnetic and paramagnetic states with the Fe substitution.     

Dielectric properties,thermal expansion and heat capacity of (1 − x)Na0.5Bi0.5TiO3–xBaTiO3 single crystals (x = 0, 0.02, 0.025, 0.0325 and 0.05)

High-quality and large-size lead-free (1 − x)Na_0.5Bi_0.5TiO₃–xBaTiO₃ single crystals (x = 0, 0.025, 0.0325 and 0.05) were grown using Czochralski method. The obtained samples were of pure perovskite structure with rhombohedral symmetry at room temperature. Thermal expansion, heat capacity, ferroelectric and dielectric properties were measured in a wide temperature range. The broad anomalies observed in thermal expansion and heat capacity were corresponded to structural, ferroelectric and dielectric anomalies, related to temperature features of polar regions and formation of a long-range order ferroelectric phase. The Burns temperature was found to increase with increasing BaTiO₃ content. At low-frequency (100 Hz–100 kHz) the samples showed diffuse phase transitions. The obtained results were discussed in terms of local electric and strain fields caused by a difference in ionic radii between (Na,Bi) and Ba ions.     

Microstructural characterization of Ce1−xTbxO2−δ (0.60 ≤ x ≤ 0.90) sintered samples

To understand the secondary phase formation in ceria based oxide, the microstructure need to be studied in a wide compositional range. However, in most previous studies, the doping concentration is lower than 50 at.%. In this work, the microstructure of Ce_1−xTb_xO_2−δ sintered samples with Tb concentrations of 0.60 ≤ x ≤ 0.90 were investigated by using X-ray diffraction (XRD) and transmission electron microscopy (TEM). Besides the fluorite-structured matrix, a secondary phase with a superstructure formed from a structural modulation of the fluorite structure along [1 1 0] and [0 0 1] directions was observed, whose amount and size reached a maximum at x = 0.90. It has a cubic structure with a lattice constant twice as large as that of the fluorite-structured matrix.     

Dielectric properties of Ba3−xKxCaNb2O9−δ (0.5 < x < 1.25) (KBCN) double perovskites

We report synthesis, structure and dielectric properties of double perovskite-type Ba_3−xK_xCaNb₂O_9−δ (x = 0.5, 0.75, 1, 1.25) (KBCN). Powder X-ray diffraction (XRD) confirmed the formation of double perovskite-type structure and lattice constant decreases with increasing K in KBCN. AC impedance study showed a single semicircle over the investigated temperatures and frequencies in dry H₂, H₂ + 3% H₂O, 3% H₂O + N₂, while two semicircles were observed at low temperatures in air, which could be attributed to bulk and grain-boundary contributions. Unlike un-doped BCN, KBCN exhibits negligible grain-boundary and electrode effects to the total electrical properties and is consistent with perovskite-type K-doped BaZrO₃. The bulk dielectric constant and dielectric loss were found to increase with increasing K content in KBCN and also found to change with sintering temperature. Among the samples investigated, Ba_1.75K_1.25CaNb₂O_9−δ sintered at 1100 °C showed the highest dielectric constant of 65 at 10⁶ Hz and dielectric loss of 0.14 at 400 °C in air. Isothermal dielectric constant and electrical conductivity at 1 MHz were found to be independent at elevated temperatures, while vary at low-frequency and low temperatures. Below 700 °C, dielectric constant and dielectric loss decreases with increasing frequency, whereas an opposite trend was observed for the electrical conductivity.     

Preparation and properties of La1 − xAgyMnO3 + δ thin epitaxial films

We report here the preparation and properties of La_1 − xAg_yMnO_3 + δ thin epitaxial films. The original two-step preparation procedure was developed. At first, La_1 − xMnO_3 + δ were grown epitaxially by metal-organic chemical vapor deposition on the single-crystal substrates (001) and (110) SrTiO₃, (001) LaAlO₃, (111) and (001) ZrO₂(Y₂O₃). Treatment by the vapor of the metallic silver in the oxygen atmosphere (at 1 bar and 20 bar) was the second step resulting in the selective absorption of silver by La_1 − xMnO_3 + δ phase. The value of y depended on the process conditions and revealed different kinetics of the silver absorption for (001) and (110) orientation of La_1 − xMnO_3 + δ films. The films prepared were characterized by X-ray diffraction, scanning electron microscopy with energy-dispersion X-ray analysis, high resolution transmission electron microscopy, X-ray photoelectron spectroscopy, electrical resistivity and magnetoresistance measurements in a four-probe configuration. We have found that metal-insulator transition temperature (T_p) in the series La_1 − xAg_xMnO_3 + δ possessed a maximum of 380 K at x = 0.15. Thus, T_p of La_1 − xAg_xMnO_3 + δ films was significantly higher than ever reported in the literature for the La_1 − xAg_xMnO_3 + δ ceramics. La_1 − xAg_xMnO_3 + δ films demonstrated the important role of the ferromagnetic fluctuations above Curie temperature T_c resulting in the sign change of the resistivity curve temperature slope dR / dT and a significant shift of T_p well above T_c. The maximum of the magnetoresistance on the temperature scale was close to dR / dT maximum. The intrinsic magnetoresistance values as high as 22% at 310 K and 50% at 280 K were measured in the magnetic field of 1 T in the series of La_1 − xAg_yMnO_3 + δ epitaxial films.     

Highly (100)-oriented Ce1 − xFexO2 − δ solid solution films prepared by laser chemical vapor deposition

Ce_1 − xFe_xO_2 − δ solid solution films were prepared on amorphous silica substrates by laser chemical vapor deposition using metal dipivaloylmethanate precursors and a semiconductor InGaAlAs (808 nm in wavelength) laser. X-ray diffraction revealed the formation of single Ce_1 − xFe_xO_2 − δ phase at x ≤ 0.15, while CeO₂ and Fe₂O₃ phases were found for higher Fe content. Highly (100)-oriented Ce_1 − xFe_xO_2 − δ (x = 0.02) films were obtained at laser power, P_L = 50-200 W and deposition temperature, T_dep = 800-1063 K. Lotgering factor (200) was calculated to be above 0.8 for films prepared at P_L = 50-150 W. X-ray photoelectron spectroscopy revealed the presence of Fe³⁺, Ce⁴⁺ and Ce³⁺ on solid solution films. Cross-sectional transmission electron microscope images disclosed a film columnar feather-like structure with a large number of nano-scale interspaces. Deposition rates were 2 or 3 orders of magnitude higher than those reported for conventional metal organic chemical vapor deposition of CeO₂.     

A new dielectric material system using (1 − x)(Mg0.95Co0.05)2TiO4–xCa0.8Sm0.4/3TiO3 at microwave frequencies

The microwave dielectric properties of the (1 − x)(Mg_0.95Co_0.05)₂TiO₄–xCa_0.8Sm_0.4/3TiO₃ ceramic system prepared by mixed oxide route have been investigated. The crystal structures and the microstructures of the ceramics were characterized by means of X-ray and SEM, respectively. The microwave dielectric properties are strongly related to the density and the matrix of the specimen. Combining (Mg_0.95Co_0.05)₂TiO₄ (spinel structure) and Ca_0.8Sm_0.4/3TiO₃ (perovskite structure) forms a two-phase system and leads to a near-zero τ_f. With increasing x, the Q × f of the specimen decreased, whereas its ?_r increased due to a compositional variation. A new microwave dielectric 0.8(Mg_0.95Co_0.05)₂TiO₄–0.2Ca_0.8Sm_0.4/3TiO₃, possessing excellent microwave dielectric properties with a dielectric constant (?_r) of 20.84, a Q × f of 112,600 GHz (where f = 9.1 GHz, is the resonant frequency) and a τ_f value ∼0.8 ppm K⁻¹ at 1573 K/4 h, is proposed as a candidate material for GPS patch antennas and 3G passive components.     

The phase transformation and crystallization kinetics of (1 − x)Li2O–xNa2O–Al2O3–4SiO2 glasses

The phase transformation and crystallization kinetics of (1 − x)Li₂O–xNa₂O–Al₂O₃–4SiO₂ glasses have been studied by using differential thermal analysis (DTA), X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and electron diffraction (ED) analysis. The crystallization temperature at the exothermic peak increases from 1171 to 1212 K when the Na₂O content increases from 0 to 0.6 mol. The crystalline phase is composed of spodumene crystallization when the Na₂O content increases from 0 to 0.6 mol. The activation energy of spodumene crystallization decreases from 444.0 ± 22.2 to 284.0 ± 10.8 kJ mol⁻¹ when the Na₂O content increases from 0 to 0.4 mol. Moreover, the activation energy increases from 284.0 ± 10.8 to 446.0 ± 23.2 kJ mol⁻¹ when the Na₂O content increases from 0.4 to 0.6 mol. The crystallization parameters m and n approach 2, indicating that the surface nucleation and two-dimensional growth are dominant in (1 − x)Li₂O–xNa₂O–Al₂O₃–4SiO₂ glasses.     

Properties of superconducting, polycrystalline dysprosium-doped Bi1.6Pb0.5Sr2−xDyxCa1.1Cu2.1O8+δ (0 ≤ x ≤ 0.5)

The structural and superconducting properties of dysprosium (Dy) doped (Bi,Pb)-2212 superconductor have been studied. Dy concentration is varied from x = 0.0 to 0.5 in a general stoichiometry of Bi_1.6Pb_0.5Sr_2−xDy_xCa_1.1Cu_2.1O_8+δ. It is found that the Dy atoms enter into the crystal structure by replacing Sr atoms and induce significant change in lattice parameter, microstructure, hole-concentration and normal state conductivity of the system. The critical temperature (T_C) and critical current density (J_C) at self-field of the Dy-doped samples enhance considerably at optimum doping levels. Maximum T_C of 92.3 K (for x = 0.4) and J_C of 1390 A/cm² at 64 K (for x = 0.2) are observed for doped samples as against 79.4 K and 127 A/cm², respectively, for the pure sample. The results are discussed on the basis of the change in hole-concentration due to Dy-doping at Sr-site of (Bi,Pb)-2212 superconductor.     

Thin film growth of boron nitride on α-Al2O3 (0 0 1) substrates by reactive sputtering

Boron nitride thin films were grown on α-Al₂O₃ (0 0 1) substrates by reactive magnetron sputtering. Infrared attenuated total reflection (ATR) spectra of the films gave an intense signal associated with in-plane B-N stretching TO mode of short range ordered structure of BN hexagonal sheets. X-ray diffraction for the film prepared at a low working pressure (ca. 1 × 10⁻³ Torr) gave a diffraction peak at slightly lower angle than that corresponding to crystal plane h-BN (0 0 2). It is notable that crystal thickness calculated from X-ray peak linewidth (45 nm) was close to film thickness (53 nm), revealing well developed sheet stacking along the direction perpendicular to the substrate surface. When the substrates of MgO (0 0 1) and Si (0 0 1) were used, the short-range ordered structure of h-BN sheet was formed but the films gave no X-ray diffraction. The film showed optical band gap of 5.9 eV, being close to that for bulk crystalline h-BN.     

Study on the chemical stability of Y-doped BaCeO3 − δ and BaZrO3 − δ films deposited by aerosol deposition

Barium cerate (BaCeO₃) has high proton conductivity but rather poor chemical stability in CO₂-containing atmospheres. Barium zirconate (BaZrO₃), in contrast, is a rather stable material, but exhibits poor sinterability. In the present work, powders of Y-doped BaCeO₃ and BaZrO₃ were synthesized via the solid solution reaction method, and dense ceramic membranes with BaCe_0.9Y_0.1O₃ and BaZr_0.85Y_0.15O₃ were prepared by the aerosol deposition method at room temperature. Aerosol deposition method is a technique that enables the fabrication of ceramic films at room temperature with a high deposition rate as well as strong adhesion to the substrate. The powders and aerosol-deposited membranes were characterized by X-ray diffraction, particle size analysis, scanning electron microscopy, and X-ray elemental mapping. The chemical stability of powders and aerosol-deposited membranes with BaCe_0.9Y_0.1O₃ and BaZr_0.85Y_0.15O₃ against water and carbon dioxide has been investigated, and it was found that BaZr_0.85Y_0.15O₃ materials showed a better chemical compatibility.     

Fabrication and photocatalytic property of Pt-intercalated layered perovskite niobates H1−xLaNb2−xMoxO7 (x = 0–0.15)

H_1−xLaNb_2−xMo_xO₇ was prepared by solid-state reaction followed by an ion-exchange reaction. Pt was incorporated in the interlayer of H_1−xLaNb_2−xMo_xO₇ by the stepwise intercalation reaction. The H_1−xLaNb_2−xMo_xO₇ showed hydrogen production activity and the activities were greatly enhanced by Pt co-incorporating. The x value in H_1−xLaNb_2−xMo_xO₇ had an important effect on the photocatalytic activity of the catalyst. When the x = 0.05, the H_1−xLaNb_2−xMo_xO₇/Pt showed a photocatalytic activity of 80 cm³ h⁻¹ g⁻¹ hydrogen evolution rate in 10 vol.% methanol solution under irradiation from a 100 W mercury lamp at 333 K.     

Phase transitions in Sr1 + xCo0.8Fe0.2O3 − δ oxides

The phase transitions that take place in Sr_1 + xCo_0.8Fe_0.2O_3 − δ (− 0.2 ≤ x ≤ 0.1) oxides are reported here. Thermogravimetric analysis (TGA) showed that the oxides with − 0.2 ≤ x ≤ 0 were prone to undergo oxygen-vacancy disorder-order phase transitions, while others with x = 0.05, 0.1 had more stable crystal structures during oxygen-desorption processes in nitrogen. These results were further confirmed by high-temperature in-situ X-ray techniques. The changes in activation energies of three typical oxides, Sr_1 + xCo_0.8Fe_0.2O_3 − δ (x = − 0.2, 0, 0.1), used as oxygen-permeable membranes were investigated. The phase transitions in Sr_1 + xCo_0.8Fe_0.2O_3 − δ (x = − 0.2, 0) have also been detected in differential scanning calorimetry (DSC) profiles.     

Fabrication of LiNi0.5 + δMn0.5 − δO2 nanofibers by electrospinning

Polycrystalline tetranary LiNi_0.5 + δMn_0.5 − δO₂ nanofibers have been successfully fabricated by a sol-gel assisted electrospinning technique. The structures and properties of fabricated nanofibers were characterized by scanning electron microscopy (SEM), X-ray powder diffraction (XRD), transmission electron microscopy (TEM) and thermal gravimetric analysis (TGA). After heat treatment of the electrospun fibers at a temperature of 800 °C, the LiNi_0.5 + δMn_0.5 − δO₂ phase was found without other trace phases. Multilayered nanoparticles with a grain size of 50 nm or less within a single fiber are notable from TEM. In this study, it was shown that the sol-gel assisted electrospun LiNi_0.5 + δMn_0.5 − δO₂ fibers could be formed with the α-NaFeO₂ type crystal structure at a temperature lower than that in a typical solid-state or sole sol-gel process and possess good thermal stability as high as 800 °C.     

Synthesis and electrical characteristics of (1 − x)BaTiO3–xK0.5Bi0.5TiO3 PTCR ceramics

Solid solutions of (1 − x)BaTiO₃–xK_0.5Bi_0.5TiO₃ were prepared by the solid state reaction technique. Samples were sintered in reducing atmosphere of N₂/H₂ in the temperature range 1100–1240 °C with subsequent oxidation at 700 °C. Phase composition and crystal structure were investigated by X-ray powder diffractometry (XRPD). It was shown that all samples of (1 − x)BaTiO₃–xK_0.5Bi_0.5TiO₃ (0 ≤ x < 0.4) exhibit a tetragonal structure at room temperature, the parameters a and c decrease with increasing x. With increasing x the Curie temperature of solid solutions (1 − x)BaTiO₃–xK_0.5Bi_0.5TiO₃ (0.1 ≤ x < 0.4) increases from 150 to 220 °C. The values of potential barriers at grain boundaries were calculated on the basis of Heywang model. With increasing x, the potential barrier at grain boundaries increases. It was shown that the grain size decreases with increasing the bismuth–potassium titanate content. The complex impedance results indicate that the grain boundary and the outer layer region, located between the boundary and the core of the grain, make a contribution to the positive temperature coefficient of resistance (PTCR) effect in (1 − x)BaTiO₃–xK_0.5Bi_0.5TiO₃ solid solutions. With increasing x ρ_max increases due to an increase in potential barrier at grain boundaries.     

Electrical conductivity and oxygen sensing behavior of SrFe0.2−xTi0.8CoxO3−δ (x = 0.05-0.2)

SrFe_0.2−xTi_0.8Co_xO_3−δ (x = 0.05-0.2) were prepared by solid-state reaction method. Phase characterization and lattice parameter evaluation were done by X-ray diffraction studies. Relative concentrations of iron in various oxidation states in these compositions were estimated using Mossbauer spectroscopy. Electrical conductivities of these bulk samples were measured in various ambient and temperatures using AC impedance spectroscopy. SrFe_0.15Ti_0.8Co_0.05O_3−δ and SrTi_0.8Co_0.2O_3−δ have been found to exhibit good change in electrical conductivity between 21% O₂ and 10 ppm O₂ in argon.     

Synthesis of β-phase Ag1−xCuxI (x = 0-0.5) solid solutions nanocrystals

A series of single β-phase nano-Ag_1−xCu_xI (x = 0-0.5) solid solutions powders were synthesized by wet-chemical-chelating reaction processing and citric acid used as complexing agent. The Ag_1−xCu_xI powders were determined by X-ray diffraction and transmission electron microscopy. It was demonstrated that the crystalline size and lattice parameter of the Ag_1−xCu_xI powders decrease with an increase in the amount of CuI substitution. The copper in the lattice of the Ag_1−xCu_xI can effectively prevent the crystalline growth of the Ag_1−xCu_xI powders and citrate used in the Ag_1−xCu_xI powders synthesized process can accelerate single β-phase crystalline structure formation.     

Characterization and electrochemical performance of (Ba0.6Sr0.4)1−xLaxCo0.6Fe0.4O3−δ (x = 0, 0.1) cathode for intermediate temperature solid oxide fuel cells

La-doped Ba_0.6Sr_0.4Co_0.6Fe_0.4O_3−δ perovskites were synthesized and investigated as new cathode material for intermediate temperature solid oxide fuel cells (IT-SOFCs). The structural characteristics, thermal expansion coefficient (TEC), electrical conductivity and electrochemical properties were characterized by X-ray diffraction (XRD), dilatometry, DC four-terminal method, electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV) techniques. The TEC of (Ba_0.6Sr_0.4)_0.9La_0.1Co_0.4Fe_0.6O_3−δ (BSLCF) was 14.9 × 10⁻⁶ K⁻¹ at 30-800 °C, lower than Ba_0.6Sr_0.4Co_0.4Fe_0.6O_3−δ (BSCF) of 15.6 × 10⁻⁶ K⁻¹. The electrical conductivity of BSCF was improved by La-doping, e.g. a value of 122 S cm⁻¹ for BSLCF vs. 52 S cm⁻¹ for BSCF at 500°C, respectively. In addition, La-doping enhanced the electrochemical activity for oxygen reduction reaction. The polarization resistance of BSLCF was 0.18 Ω cm² at 700 °C, about a quarter lower than that of BSCF. The improved electrochemical performance of BSLCF should be ascribed to the higher conductivity as well as the improved oxygen adsorption/desorption and oxygen ions diffusion processes.     

(0 0 6)-oriented α-Al2O3 films prepared in CO2-H2 atmosphere by laser chemical vapor deposition using a diode laser

(0 0 6)-oriented α-Al₂O₃ films were prepared by laser chemical vapor deposition (LCVD) using aluminum acetylacetonate (Al(acac)₃) in CO₂-H₂ atmosphere. The effects of the CO₂ mole fraction (FCO₂) and laser power (P_L) on the crystal phase, microstructure, and deposition rate (R_dep) were investigated. α- and γ-Al₂O₃ mixture films were prepared at P_L = 90 W (deposition temperature of 818 K), whereas (0 0 6)-oriented single-phase α-Al₂O₃ films were obtained at P_L = 110 W (863 K). The texture coefficient and the grain size of the (0 0 6)-oriented films increased with increasing FCO₂. The orientation of the α-Al₂O₃ films changed from (0 0 6) to (1 0 4) to (0 1 2) with increasing P_L (T_dep). The R_dep of the (0 0 6)-oriented α-Al₂O₃ films increased with increasing FCO₂.     

Significant improvement of the oxygen permeation flux of tubular Ba0.5Sr0.5Co0.8Fe0.2O3 − δ membranes covered by a thin La0.6Sr0.4Ti0.3Fe0.7O3 − δ layer

We present a new method to improve the oxygen flux properties and stability of Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3 − δ tube membrane using a thin layer of La_0.6Sr_0.4Ti_0.3Fe_0.7O_3 − δ as protective coatings. The first relevant result is that the La_0.6Sr_0.4Ti_0.3Fe_0.7O_3 − δ protective layer had an extraordinary positive effect on improving the oxygen permeation flux of the tubular Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3 − δ membranes. La_0.6Sr_0.4Ti_0.3Fe_0.7O_3 − δ-coated Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3 − δ tubular membrane showed the highest oxygen permeability with the flux reaching ~ 3 ml cm⁻² min⁻¹ (oxygen purity > 99%) at 950 °C in static atmospheric pressure through a 1.0 mm thick membrane.