单斜相与四方相混合晶相组成ZrO2负载镍催化剂催化顺酐选择性加氢

通过调控水热法制备条件制备同为单斜相和四方相混合晶相组成、但织构性质和表面结构性质不同的两种ZrO_2载体,采用浸渍法制备镍质量分数为10%的Ni/ZrO_2催化剂,考察不同反应温度[(150～240)℃]和氢气压力[(3～7)MPa]条件下两种ZrO_2载体负载镍催化剂的顺酐加氢性能。采用XRD、H_2-TPR、H_2-TPD和拉曼光谱等对催化剂进行表征。结果表明,与镍物种发生较强相互作用的ZrO_2负载镍催化剂具有较高的■键加氢活性与选择性,几乎没有■加氢活性,在所考察的反应温度和反应压力范围,催化剂上丁二酸酐选择性均高于95.1%,γ-丁内酯选择性均低于4.9%。与之不同,与镍物种发生较弱相互作用的ZrO_2负载镍催化剂具有较弱的■键加氢活性,然而,该催化剂表现出一定的■加氢活性,并且其■加氢活性随反应温度或反应压力的提高而显著提高。在反应温度240℃、氢气压力5 MPa条件下,γ-丁内酯选择性高达60.6%。推测晶相组成相似的两种ZrO_2载体负载镍催化剂明显的■加氢性能差异与其表面结构性质不同有关。     

PtAu/ZrO_2催化甘油选择性制备乳酸

采用溶胶-沉积法制备了Pt Au/ZrO_2系列催化剂,在惰性气体气氛下用于催化甘油选择性制备乳酸。研究不同反应温度下,不同单金属负载和不同比例Pt Au双金属负载催化剂的催化活性以及不同气氛下催化剂重复使用性能,对催化剂进行BET、AAS和TEM等表征。结果表明,在浓度1.1 mol·L-1甘油水溶液10 m L、(1∶1)Pt Au/ZrO_2催化剂用量0.132 g、反应温度160℃、氮气压力1.4 MPa和反应时间6 h条件下,甘油转化率90%,乳酸选择性93.7%。催化剂重复使用性能实验验证了氧气气氛下催化剂活性保持良好。     

Effect of Zr-SBA-15 support on catalytic functionalities of Mo, CoMo, NiMo hydrotreating catalysts

SBA-15 and ZrO₂ (10–50 wt.%) containing SBA-15 mesoporous materials were prepared by direct and post-synthesis methods. Characterization using low angle XRD, pore size distribution, CO₂ chemisorption indicate that hexagonal mesoporous structure is retained even after ZrO₂ addition (25 wt.%). Mo, CoMo and NiMo catalysts prepared using these supports were examined by XRD, oxygen chemisorption, temperature programmed reduction (TPR). The catalysts were tested for hydrodesulfurization (HDS) of thiophene and hydrogenation (HYD) of cyclohexene. HDS of thiophene for 8%Mo, 3%Co8%Mo, and 3%Ni8%Mo increases with increasing ZrO₂ loading in SBA-15 up to 25 wt.%. Oxygen chemisorption and TPR hydrogen consumption indicated that the molybdenum dispersion and anion vacancies, and catalytic activities are significantly influenced by ZrO₂ content in Zr-SBA-15. A comparison indicated that TiO₂-SBA-15, ZrO₂-SBA-15 supported CoMo catalysts show higher activities for hydrodesulfurization.     

Fischer–Tropsch synthesis over Re-promoted Co supported on Al2O3, SiO2 and TiO2: Effect of water

The activity and selectivity of rhenium promoted cobalt Fischer–Tropsch catalysts supported on Al₂O₃, TiO₂ and SiO₂ have been studied in a fixed-bed reactor at 483 K and 20 bar. Exposure of the catalysts to water added to the feed deactivates the Al₂O₃ supported catalyst, while the activity of the TiO₂ and SiO₂ supported catalysts increased. However, at high concentrations of water both the SiO₂ and TiO₂ supported catalyst deactivated. Common for all catalysts was an increase in C₅₊ selectivity and a decrease in the CH₄ selectivity by increasing the water partial pressure. The catalysts have been characterized by scanning transmission electron microscope (STEM), BET, H₂ chemisorption and X-ray diffraction (XRD).     

Modified Co3O4/ZrO2 catalysts for VOC emissions abatement

The catalytic activity study of cobalt oxides dispersed on different supports evidenced first the highest performances of zirconia based catalysts in the reaction of toluene oxidation. The influence of the presence of ethylenediamine (en) during the preparation of Co/ZrO₂ and the ZrO₂ support modification by Y₂O₃ were then studied and compared with reference catalyst prepared conventionally by impregnation of ZrO₂ with an aqueous solution of Co(NO₃)₂. Addition of an aqueous solution of ethylenediamine to a cobalt nitrate solution led to a strong increase on the catalytic activity of the activated solids in the toluene deep oxidation as compared with the reference catalyst. The best catalytic results were explained in terms of cobalt oxides dispersion but also in terms of Co–support interaction. The generated cobalt species were reducible at much lower temperatures and then were more active in the toluene total oxidation. Finally an efficient catalyst for VOC oxidation was produced combining the modifications of ZrO₂ by yttrium and of the precursor.     

载体对镍基催化剂顺酐液相加氢性能的影响

分别以ZrO₂、SiO₂与Al₂O₃为载体,采用等体积浸渍法制备了Ni质量分数为15%的催化剂,考察了其催化顺酐液相加氢性能,并利用BET、XRD、H₂-TPR以及TPO-MS等表征手段对催化剂进行了详细表征。结果表明,随载体不同各催化剂的加氢活性及选择性存在较大差异,Ni/Al₂O₃催化剂的C=C键加氢活性最高,但其几乎没有C=O加氢活性,催化顺酐加氢主产物为丁二酸酐。Ni/ZrO₂催化剂具有最高的C=O加氢活性,催化顺酐加氢主产物为γ-丁内酯,在反应温度为483 K,氢气压力为5 MPa的条件下反应8 h时,Ni/ZrO₂催化剂的γ-丁内酯选择性达79.20%。催化剂的套用实验表明,Ni/ZrO₂与Ni/SiO₂催化剂具有高的使用稳定性,Ni/Al₂O₃催化剂则在套用过程中快速失活。顺酐加氢至γ-丁内酯的中间产物--丁二酸酐与催化剂间的相互作用是影响催化剂加氢选择性及使用稳定性的主要原因。     

Development of new catalysts for N2O-decomposition from adipic acid plant

Direct decomposition of N₂O was investigated using simulated and real industrial gas stream coming from an adipic acid plant. Two different kinds of catalysts were studied: (i) LaB_1−xB′_xO₃ and CaB_1−xCu_xO₃ (B = Mn, Fe and B′ = Cu, Ni) perovskites (PVKs) and (ii) supported PVKs (10 or 20 wt.%) on γ-Al₂O₃ and CeO₂–ZrO₂. The structural modifications induced by the composition of PVK samples affect the catalytic performances: mixed oxide formation in CaMn_0.7Cu_0.3O₃ samples allows to reach the highest values of N₂O conversion while the effect of PVK phases is more controversial. The importance of copper on catalytic activities is confirmed by the investigation on CaMn_1−xCu_xO₃ samples. The best results were obtained with a CaMn_0.6Cu_0.4O₃ catalyst calcined at 700 °C for 5 h, in which the presence of copper maximises the Ca₃CuMnO₆ phase formation. The increase in Cu-content produces a large segregation of CuO despite PVK formation. The best catalyst was tested using industrial gas stream, showing good stability also in the presence of H₂O and O₂ (8% v/v ) after 1400 h on-stream. To increase surface area, Cu-containing PVKs were deposed on γ-Al₂O₃ and CeO₂–ZrO₂, and this latter has been recognised as the best support. Indeed, the activity of the PVKs supported on ceria–zirconia is comparable to and even better than that of the bulk catalysts. A possible explanation regards the support contribution in terms of activity and/or promotion of O₂ mobility which enhances the overall activity of the catalyst.     

The structures of VOx/MOx and alkali-VOx/MOx catalysts and their catalytic performances for soot combustion

Vanadium oxides supported on γ-Al₂O₃, SiO₂, TiO₂, and ZrO₂ were studied on their molecular structures and reactive performances for soot combustion. To investigate the effect of different alkali metals on the structures and reactivities of supported-vanadium oxide catalysts, they were doped into the V₄/TiO₂ catalyst which had the best intrinsic activity for soot combustion in the selected supported vanadium oxide catalysts. The experimental results demonstrated that the catalytic properties of these catalysts depended on the vanadium loading amount, support nature, and the presence or the absence of alkali metals. The spectroscopic analysis (FT-IR and UV–vis) and H₂-TPR results revealed that the higher activity of alkali-promoted vanadium oxide catalysts could be related to the ability of alkali metal promoting the redox cycle of the active vanadyl species. TG results showed that adding alkali to V_m/TiO₂ catalyst was beneficial to lowering their melting points. Low melting points could ensure the good surface atom migration ability, which would improve the contact between the catalyst and soot. Due to the alkali metal components promoting the redox ability and the mobility of the catalysts, alkali-modified vanadium oxide catalysts could remarkably improve their catalytic activities for soot combustion. The catalytic activity order for soot combustion followed Li > Na > K > Rb > Cs in the catalyst system of alkali-V₄/TiO₂, and the reason why it followed this sequence was discussed.     

Hydrogen production by autothermal reforming of sulfur-containing hydrocarbons over re-modified Ni/Sr/ZrO2 catalysts

The catalytic autothermal reforming (ATR) of liquid hydrocarbons to provide hydrogen for mobile or stationary fuel cells was carried out over a Ni/Sr/ZrO₂ catalyst that is active for steam reforming (SR). The catalyst system was found to be active for the ATR reaction, although the hydrogen concentration obtained by ATR, under the conditions employed, was a little lower than that for SR. Addition of sulfur, introduced in the form of thiophene, reduced the catalytic stability of Ni/Sr/ZrO₂, even at 1073 K. The catalyst lifetime decreased with increasing sulfur concentration between 0 and 100 ppm. Additives for improving the sulfur-tolerance of Ni/Sr/ZrO₂ were examined, and additions of Re or La were found to be effective in improving the stability of the catalysts. The best catalyst was 5 wt.% Re–Sr/Ni/ZrO₂. This catalyst was used in the ATR of liquid hydrocarbon fuels such as commercial premium gasoline, hydrotreated FCC gasoline, reagent mixtures, and methylcyclohexane. For premium gasoline, the activity remained unchanged during 30 h, but then diminished rapidly. With the other fuels, however, the catalyst showed a much improved performance, indicating that the presence of sulfur could be associated with catalyst stability. ATR coupled with the water–gas shift reaction led to a reduction in the CO concentration by up to 2800 ppm. The catalyst's activity remained constant even after cold-start runs with 853–423–853 K temperature cycles under H₂O/O₂/N₂ conditions. Thus, the Re–Sr/Ni/ZrO₂ catalyst is effective for ATR of liquid hydrocarbon fuels. Further work is currently under way to extend the catalyst life.     

Additional effects of cobalt precursor and zirconia support modifications for the design of efficient VOC oxidation catalysts

The influence of the ZrO₂ support modification by Y₂O₃ and the presence of ethylenediamine (“en”) during the preparation of Co/ZrO₂ were studied and compared with a reference catalyst conventionally prepared by impregnation of ZrO₂ with an aqueous solution of Co(NO₃)₂. The effect of the en/Co molar ratio (x = 1–3) was studied. Activation of cobalt species was followed by differential thermal and thermogravimetric analyses (DTA/TG) analyses and by specific surface area measurements which evidence the complete cobalt precursor decomposition at 450 °C, whatever the support composition and the en/Co molar ratio. The addition of an aqueous solution of ethylenediamine to a cobalt nitrate solution led to a strong increase in the catalytic activity of the activated solids for the toluene deep oxidation as compared to the reference catalyst. The best catalytic results were explained in terms of cobalt oxides dispersion (X-ray diffraction (XRD)) and also in terms of Co-support interaction (H₂-temperature-programmed reduction (TPR)). The generated cobalt species were reducible at much lower temperatures and were more active in the toluene total oxidation. Finally, an efficient catalyst was produced combining the modifications of the support by yttrium oxide and of the precursor (use of ethylenediamine).     

Characterizations of platinum catalysts supported on Ce, Zr, Pr-oxides and formation of carbonate species in catalytic wet air oxidation of acetic acid

Catalytic wet air oxidation (CWAO) of aqueous solution of acetic acid (78 mmol L⁻¹) was carried out with pure oxygen (2 MPa) at 200 °C in a stirred batch reactor on platinum supported oxide catalysts (Pt/oxide, oxide = CeO₂, Zr_0.1Ce_0.9O₂, Zr_0.1(Ce_0.75Pr_0.25)_0.9O₂ and ZrO₂). Platinum was loaded on oxides by impregnation (5 wt%), and then the catalysts were reduced under H₂. Homogenous dispersions of 2–3 nm metal crystallites were obtained. The catalytic activity depended on the ability of the support to resist to the formation of carbonates. Ce(CO₃)OH species, determined by FT-IR and XRD, were rapidly formed during the CWAO reaction especially on mixed oxides. These carbonates were responsible to a drastic drop in catalytic performances. Amounts of carbonate species increase with the ability of the catalyst to transfer oxygen.     

Nitrate catalytic reduction in water using niobia supported palladium–copper catalysts

Niobia and alumina supported palladium catalyst promoted by copper were investigated in the reaction of nitrate catalytic reduction in water and characterized by temperature programmed reduction, physisorption, H₂ chemisorption and X-ray diffraction. Niobia supported Pd–Cu catalysts were as active and selective as an alumina supported catalyst. All catalysts had similar turnover frequencies independent of the support. The control of pH and the interaction between Pd and Cu were critical to improving the selectivity and activity of Pd–Cu/Nb₂O₅ catalysts.     

Partial oxidation and combined reforming of methane on Ce-promoted catalysts

Pt/ZrO₂ and Pt/Ce_0.14Zr_0.86O₂ catalysts containing 0.5 and 1.5 wt.% Pt were studied in order to evaluate the effect of the support reducibility and metal dispersion on the catalyst stability for the partial oxidation and the combined partial oxidation and CO₂ reforming of methane. The Pt/Ce_0.14Zr_0.86O₂ catalysts proved to be more active, stable and selective than Pt/ZrO₂ catalysts during the partial oxidation reaction. No increase in deactivation was observed when the CH₄:O₂ feed ratio was increased from 2:1 to 4:1. In addition, no water formation was observed at the high CH₄:O₂ ratios. The activity of the catalyst is dependent upon both the dispersion and the ability of the catalyst to resist carbon deposition.

The addition of CO₂ resulted in a decrease in the methane conversion and a decrease in the H₂/CO ratio for the Ce_0.14Zr_0.86O₂ and ZrO₂ supported catalysts. Small increases in the temperature of the bed have been recorded during the partial oxidation reaction. However, within a few minutes the temperature stabilizes below the furnace temperature providing indirect evidence for the combined combustion and reforming mechanisms previously proposed. The 1.5 wt.% Pt/CeZrO₂ catalyst shows promise for the autothermal reforming reaction based on the stability during transient operation.     

Ethylene dimerization over NiSO4 supported on Fe2O3-promoted ZrO2 catalyst

The NiSO₄ supported on Fe₂O₃-promoted ZrO₂ catalysts were prepared by the impregnation method. Fe₂O₃-promoted ZrO₂ was prepared by the coprecipitation method using a mixed aqueous solution of zirconium oxychloride and iron nitrate solution followed by adding an aqueous ammonia solution. No diffraction line of nickel sulfate was observed up to 20 wt.%, indicating good dispersion of nickel sulfate on the surface of Fe₂O₃–ZrO₂. The addition of nickel sulfate (or Fe₂O₃) to ZrO₂ shifted the phase transition of ZrO₂ (from amorphous to tetragonal) to higher temperatures because of the interaction between nickel sulfate (or Fe₂O₃) and ZrO₂. 15-NiSO₄/5-Fe₂O₃–ZrO₂ containing 15 wt.% NiSO₄ and 5 mol% Fe₂O₃, and calcined at 500 °C exhibited a maximum catalytic activity for ethylene dimerization. NiSO₄/Fe₂O₃–ZrO₂ catalysts was very effective for ethylene dimerization even at room temperature, but Fe₂O₃–ZrO₂ without NiSO₄ did not exhibit any catalytic activity at all. The catalytic activities were correlated with the acidity of catalysts measured by the ammonia chemisorption method. The addition of Fe₂O₃ up to 5 mol% enhanced the acidity, surface area, thermal property, and catalytic activities of catalysts gradually, due to the interaction between Fe₂O₃ and ZrO₂ and due to consequent formation of Fe–O–Zr bond.     

Reforming of methane and coalbed methane over nanocomposite Ni/ZrO2 catalyst

Nanocomposite Ni/ZrO₂-AN catalyst consisting of comparably sized Ni metal and ZrO₂ nanoparticles is studied in comparison with zirconia- and alumina-supported Ni catalysts (Ni/ZrO₂-CP and commercial Ni/Al₂O₃-C) for steam reforming of methane (SRM) and for combined steam and CO₂ reforming of methane (CSCRM). The reactions are performed under atmospheric pressure with stoichiometric amounts of H₂O and CH₄ or (H₂O + CO₂) and CH₄ at 1073 K. Under a wide range of methane space velocity (gas hourly space velocity of methane GHSV_CH4 = 12,000–96,000 ml/(h g_cat.), the nanocomposite Ni/ZrO₂-AN catalyst always shows higher activity and stability for both SRM and CSCRM reactions. The two supported Ni catalysts (Ni/ZrO₂-CP and Ni/Al₂O₃-C) exhibit fairly stable catalysis under low GHSV_CH4 but they are easily deactivated under high GHSV_CH4 and become completely inactive when they are reacted for ca.100 h at GHSV_CH4 = 48,000 ml/(h g_cat.). The CSCRM reaction is carried out with different H₂O/CO₂ ratios in the reaction feed while keeping the molar ratio (H₂O + CO₂)/CH₄ = 1.0, the results prove that the nanocomposite Ni/ZrO₂-AN catalyst can be highly promising in enabling a catalytic technology for the production of syngas with flexible H₂/CO ratios (ca. H₂/CO = 1.0–3.0) to meet the requirements of various downstream chemical syntheses.     

Gold catalysts supported on mesoporous zirconia for low-temperature water–gas shift reaction

Mesoporous ZrO₂ with high surface area and uniform pore size distribution, synthesized by surfactant templating through a neutral [C₁₃(EO)₆–Zr(OC₃H₇)₄] assembly pathway, was used as a support of gold catalysts prepared by deposition–precipitation method. The supports and the catalysts were characterized by powder X-ray diffraction, scanning and transmission electron microscopy, N₂ adsorption analysis, temperature programmed reduction and desorption. The catalytic activity of gold supported on mesoporous zirconia was evaluated in water–gas shift (WGS) reaction at wide temperature range (140–300 °C) and at different space velocities and H₂O/CO ratios. The catalytic behaviour and the reasons for а reversible deactivation of Au/mesoporous zirconia catalysts were studied. The influence of gold content and particle size on the catalytic performance was investigated. The WGS activity of the new Au/mesoporous zirconia catalyst was compared to the reference Au/TiO₂ type A (World Gold Council), revealing significantly higher catalytic activity of Au/mesoporous zirconia catalyst. It is found that the mesoporous zirconia is a very efficient support of gold-based catalyst for the WGS reaction.     

Effect of solvo-thermal treatment temperature on the properties of sol–gel ZrO2–TiO2 mixed oxides as HDS catalyst supports

ZrO₂–TiO₂ mixed oxide (30–70 mol/mol) was prepared by low-temperature sol–gel followed by solvo-thermal treatment (1 day) at various temperatures (40, 80, 120, 160 and 200 °C). Selected samples of the corresponding single oxides were also prepared. Materials characterization was carried out by N₂ physisorption, XRD, thermal analysis (TG-DTA) and UV–vis DRS, infra-red and Laser-Raman spectroscopies. Binary solids of enhanced pore volume and pore size diameter were obtained by increasing the post-treatment severity. Anatase TiO₂ micro-segregation was evidenced by Raman spectroscopy for the mixed oxide solvo-treated at the highest temperature. This solid also showed the highest crystallization temperature to ZrTiO₄ (702 °C). Mo impregnated (2.8 atom nm⁻²) on various mixed oxides was sulfided under H₂S/H₂ (400 °C, 1 h), the catalysts being tested in the dibenzothiophene hydrodesulfurization (HDS, T = 320 °C, P = 5.59 MPa). By increasing the severity of the solvo-treatment improved supports for MoS₂ phase were obtained. The HDS activity of the catalyst with carrier post-treated at 200 °C was 40% higher (in per total mass basis) than that of sulfided Mo supported on the binary oxide solvo-treated at 80 °C. The ZrO₂–TiO₂-supported catalysts showed higher selectivity to products from the hydrogenation route than their counterparts supported on either single oxide.     

Partial oxidation of methane to synthesis gas over Co/Ca/Al2O3 catalysts

A series of calcium-modified alumina-supported cobalt catalysts were prepared with a two-step impregnation method, and the effect of calcium on the catalytic performances of the catalysts for the partial oxidation of methane to syngas (CO and H₂) was investigated at 750 °C. Also, the catalysts were characterized by XRD, TEM, TPR and (in situ) Raman. At 6 wt.% of cobalt loading, the unmodified alumina-supported cobalt catalyst showed a very low activity and a rapid deactivation, while the calcium-modified catalyst presented a good performance for this process with the CH₄ conversion of 88%, CO selectivity of 94% and undetectable carbon deposition during a long-time running. Characterization results showed that the calcium modification can effectively increase the dispersion and reducibility of Co₃O₄, decrease the Co metal particle size, and suppress the reoxidation of cobalt as well as the phase transformation to form CoAl₂O₄ spinel phases under the reaction conditions. These could be related to the excellent catalytic performances of Co/Ca/Al₂O₃ catalysts.     

Ni/ZrO2-SiO2催化剂催化乙酰丙酸加氢合成γ-戊内酯

分别以ZrO₂、SiO₂及ZrO₂-SiO₂复合氧化物为载体,采用等体积浸渍法制备了Ni含量为10%（质量分数）的催化剂,考察了其催化乙酰丙酸液相加氢性能。采用N₂-物理吸附、NH₃-TPD、H₂-TPR、XRD、TEM等表征手段对催化剂进行了表征。研究结果表明,在所制备的催化剂上,乙酰丙酸先经C=O加氢生成4-羟基戊酸,后者快速脱水酯化为γ-戊内酯。Ni/ZrO₂-SiO₂催化剂较Ni/ZrO₂与Ni/SiO₂催化剂具有高的金属分散度和丰富的表面酸性中心,表现出高的C=O加氢活性以及优异的乙酰丙酸加氢合成γ-戊内酯性能。在反应温度为200℃,氢气压力4 MPa的反应条件下,乙酰丙酸的转化率达到100%,γ-戊内酯的选择性大于99.9%。     

SiO2负载钴系催化剂的环己烯环氧化性能

采用沉积沉淀法制备不同负载量的SiO₂（硅胶）负载钴氧化物催化剂,采用X射线衍射（XRD）、X射线光电子能谱（XPS）、透射电镜（TEM）、N₂吸脱附等手段对催化剂进行表征,结果表明钴系氧化物为Co₃O₄,并且钴氧化物均匀地负载在SiO₂（硅胶）载体上,其活性组分的粒子大小集中分布在2～10nm。将制备的催化剂应用于环己烯环氧化反应,以环己烯、分子氧为原料,异丁醛为催化助剂,N,N-二甲基甲酰胺（DMF）为反应溶剂,在高压釜中进行。同时将SiO₂负载钴氧化物催化剂与不同载体上制备的钴系催化剂进行比较,发现催化剂用量0.20g、环己烯2.00g、异丁醛3.50g、反应温度50℃、反应时间5h、氧气压力4MPa时,环己烯的转化率和环氧环己烷的选择性分别可达到66.56%和71.03%。