Properties of self-compacting concrete prepared with coarse and fine recycled concrete aggregates

In this study, the fresh and hardened properties of self-compacting concrete (SCC) using recycled concrete aggregate as both coarse and fine aggregates were evaluated. Three series of SCC mixtures were prepared with 100% coarse recycled aggregates, and different levels of fine recycled aggregates were used to replace river sand. The cement content was kept constant for all concrete mixtures. The SCC mixtures were prepared with 0, 25, 50, 75 and 100% fine recycled aggregates, the corresponding water-to-binder ratios (W/B) were 0.53 and 0.44 for the SCC mixtures in Series I and II, respectively. The SCC mixtures in Series III were prepared with 100% recycled concrete aggregates (both coarse and fine) but three different W/B ratios of 0.44, 0.40 and 0.35 were used. Different tests covering fresh, hardened and durability properties of these SCC mixtures were executed. The results indicate that the properties of the SCCs made from river sand and crushed fine recycled aggregates showed only slight differences. The feasibility of utilizing fine and coarse recycled aggregates with rejected fly ash and Class F fly ash for self-compacting concrete has been demonstrated.     

Influence of recycled coarse aggregates on permeability of fresh concrete

The following work is an experimental study of the behaviour of very early-age concrete. Six different concretes, four of them containing recycled coarse aggregates were studied for the first 2.5 h. The studies were carried out in a ventilated tunnel in order to imitate severe desiccation conditions. In order to indirectly obtain the permeability coefficient, settlement, capillary depression and evaporation were measured for all six concretes. The initial permeability coefficient of each concrete is determined starting from initial bleeding rate. The use of recycled coarse aggregates leads to a high bleeding rate for high water to cement ratios. Permeability coefficients at air entry are then determined starting from capillary depression gradients. Recycled coarse aggregates do not seem to influence the air entry value which is highly dependent on the paste quality. At air entry, the permeability coefficient of recycled coarse aggregates concrete mixes is higher than that of natural aggregates concrete mixes. At high evaporation rates, in severe desiccation conditions, recycled coarse aggregates seem to reduce bleeding for mixture with low water cement ratios. Permeability coefficient is a key physical parameter to understand drying of fresh concrete.     

Structural concrete with incorporation of coarse recycled concrete and ceramic aggregates: durability performance

The growing difficulty in obtaining natural coarse aggregates (NCA) for the production of concrete, associated to the environmental issues and social costs that the uncontrolled extraction of natural aggregates creates, led to a search for feasible alternatives. One of the possible paths is to reuse construction and demolition waste (CDW) as aggregates to incorporate into the production of new concrete. Therefore, a vast and detailed experimental campaign was implemented at Instituto Superior Técnico (IST), which aimed at determining the viability of incorporating coarse aggregates from concrete and ceramic brick wall debris, in the production of a new concrete, with properties acceptable for its use in new reinforced and pre-stressed structures. In the experimental campaign different compositions were studied by incorporating pre-determined percentages of recycled coarse concrete aggregates and recycled coarse ceramic plus mortar particles, and the main mechanical, deformability and durability properties were quantified, by comparison with a conventional reference concrete (RC). In this article, these results are presented in terms of the durability performance of concrete, namely water absorption, carbonation and chlorides penetration resistance.     

Impact of the initial moisture level and pre-wetting history of recycled concrete aggregates on their water absorption

Initial moisture and pre-wetting method influence on the water absorption of recycled concrete aggregates (RCA) have been studied experimentally. For this purpose, RCA were pre-wetted by three methods: soaking under partial vacuum (simulating long term wetting), soaking under atmospheric pressure, and spraying (simulating short term wetting). The results show that the same initial amount of water in two samples of RCA do not lead to the same total amount of water absorbed by RCA during 5–120 min. The latter depends on the way they have been pre-wetted (either long term or short term). It is suggested that this phenomenon is related to the accessibility filled pores in the different pre-wetting methods. So, the pre-wetting history of RCA could change the amount of total water absorbed by the RCA up to 1%. When mixing and casting concrete are produced with RCA, the corresponding error in the determination of the effective water should have adverse effects on the fresh and hardened concrete characteristics. In this study real applications on mixtures of recycled concrete have been carried out, where the influence of initial moisture content and pre-wetting history of RCA on fresh recycled concrete properties (slump) have been investigated.     

The effect of paste volume and of water content on the strength and water absorption of concrete

The W/C ratio is generally considered to be the governing parameter, which affects the strength and durability of concrete. In this paper, the effect of paste volume and of water content on capillary absorption and strength is investigated on concrete mixes having the same W_ef/C ratio. Four W_ef/C ratios (0.3, 0.4, 0.5, 0.6) were used and for each W_ef/C ratio four mixes were prepared with effective water contents 140, 180, 220 and 260 l/m³. It is found that although the W_ef/C ratio is kept constant, strength increases and capillary absorption decreases when the volume of the water or the volume of the paste decreases. The effect of the paste or water content by volume on strength is stronger for lower W/C ratios and for water contents at the lower or upper values (140 l/m³, 260 l/m³) used in the investigation. Similarly capillary absorption is higher the higher is the value of W_ef/C ratio and, with constant W_ef/C ratio, increases approximately linearly as the paste content increases. The rate of increase is lower for lower values of W_ef/C ratios.     

Durability of recycled aggregate concrete prepared with carbonated recycled concrete aggregates

The mechanical properties of recycled aggregate concrete (RAC) incorporating carbonated recycled concrete aggregates (RCAs) have previously been reported. However, the durability of RAC prepared with carbonated RCAs remains to be accessed. In this study, the durability properties of RAC prepared with non-carbonated RCAs and carbonated RCAs, in terms of deformation (drying shrinkage), water absorption and permeability (bulk electrical conductivity, gas and chloride ion permeability), are presented. The experimental results indicated that: (i) the incorporation of the carbonated RCAs in RAC not only helped to reduce the water absorption of RAC, but also reduced its permeability; (ii) when 100% carbonated NRCAs was used, the improvement extent of impermeability was 15.1%, 36.4% and 42.4% for bulk electrical conductivity, chloride ion permeability and gas permeability, respectively. Comparing the results of the mechanical and durability properties, the CO₂ curing treatment of RCAs had a greater beneficial impact on the durability properties of the RAC; and (iii) there was a good correlation between the water absorption of RAC and its permeability indicators. The water absorption value of RAC may be used as a criterion of the durability of RAC.     

Effect of recycled coarse aggregate on damage of recycled concrete

This study evaluates the possibility of measuring the damage of the recycled concrete. In this way, two conventional concretes with a w/c ratio of 0.55 and 0.65 were designed. Based on them, six recycled concretes with different percentages of replacement of natural coarse aggregates with recycled coarse aggregate (20, 50 and 100%) were obtained. To take into account the high absorption capacity of the recycled aggregates, before using them they were pre-wetted for 10 min. The results concluded that scalar damage mechanics (based on the variations of the elastic modulus) and volumetric strains curves can be use to quantify the damage of the recycled concrete. The results from both approaches indicated that the damage to concrete depended on the percentage of replacement, increasing with higher replacement percentages. Additionally, values of the damage, that are quantified using the critical stress and according to the scalar damage mechanics, are given.     

Pore characterization of manufactured aggregates: recycled concrete aggregates and lightweight aggregates

Accurate characterization of aggregates plays an important role in mixture proportioning of concrete mixes. Decisions made during the concrete design phase in terms of characterization techniques adopted for quantification of specific gravity or water absorption affect the development of fresh properties during the construction phase as well as impacting the long term performance of concrete. Manufactured aggregates such as recycled concrete aggregates (RCA) and lightweight aggregate (LWA) are more absorptive than natural aggregate. Due to the thrust on construction of sustainable structures usage of LWA and RCA has increased significantly in the last decade. In this study, standard ASTM techniques adopted for porosity and specific gravity measurement of aggregates were compared with automated testing equipment such as the helium pycnometer and the envelope density analyzer. Porosity of different aggregates obtained using different test methods was compared with image analysis. Pore diameter characterization of different RCA was conducted using image analysis.     

Specifications for concrete with recycled aggregates

RILEM Recommendation121-DRG Guidance for Demolition and Reuse of Concrete and Masonry

Specifications for concrete with recycled aggregates     

Properties of concrete prepared with PVA-impregnated recycled concrete aggregates

This paper reports an experimental study to improve the properties of recycled concrete aggregates (RCA) by their impregnation with polyvinyl alcohol (PVA). The effects of PVA on the development of strength and durability properties of the recycled aggregate concrete were evaluated. The experimental investigation was conducted in two parts. Firstly, the optimal concentration of PVA solution required to improve the recycled aggregates was determined. The RCA was soaked in 6%, 8%, 10%, 12% PVA solutions, and impregnation was conducted under a controlled laboratory environment. Density, crushing value (10% fines value), and water absorption of the PVA impregnated RCA (PI-RCA) were determined. Secondly, the slump, slump loss, compressive and tensile splitting strength, dimensional change (shrinkage) and chloride penetrability of the concretes prepared with the RCA that had been impregnated with the optimal (10%) PVA concentration were determined. It was found that the 10% fines value of the PI-RCA was higher, and the water absorption of the PI-RCA were lower when compared to the untreated RCA. The results show that there was not only an improvement in the mechanical properties of the concrete made with PI-RCA, but also the shrinkage of PI-RCA decreased while the resistance to chloride-ion penetration of the concrete produced increased.     

Quantification of the residual mortar content in recycled concrete aggregates by image analysis

As the supply of suitable fresh aggregates in some locations is rapidly dwindling and such aggregates need to be transported from distant locations, there will be more and more economic and environmental reasons to use recycled concrete aggregates in making new concrete. The nature and properties of recycled concrete aggregates have a definite impact on the performance of recycled aggregate concrete and the effects can vary considerably. Existing literature and studies conducted by the authors have shown that the amount and properties of the residual mortar in the recycled concrete aggregates significantly affect the mechanical and durability properties of the new concrete. Consequently, a quick laboratory method was developed to determine the residual mortar content of recycled concrete aggregates, to serve as a quality control tool for such aggregates. In order to validate the results obtained by that laboratory test procedure, image analysis was used to quantify the residual mortar content in the different size fractions of the recycled concrete aggregates tested. The results confirmed that the quick laboratory test provides an accurate measurement of the residual mortar content in recycled concrete aggregates.     

Durability performance of concrete made with fine recycled concrete aggregates

Fine recycled aggregates are seen as the last choice in recycling for concrete production. Many references quote their detrimental influence on the most important characteristics of concrete: compressive and tensile strength; modulus of elasticity; water absorption; shrinkage; carbonation and chloride penetration. These two last characteristics are fundamental in terms of the long-term durability of reinforced or prestressed concrete. In the experimental research carried out at IST, part of which has already been published, different concrete mixes (with increasing rates of substitution of fine natural aggregates – sand – with fine recycled aggregates from crushed concrete) were prepared and tested. The results were then compared with those for a reference concrete with exactly the same composition and grading curve, but with no recycled aggregates. This paper presents the main results of this research for water absorption by immersion and capillarity, chloride penetration (by means of the chloride migration coefficient), and carbonation resistance, drawing some conclusions on the feasibility of using this type of aggregate in structural concrete, while taking into account any ensuing obvious positive environmental impact.     

Mechanical behaviour of concrete made with fine recycled concrete aggregates

This paper concerns the use of fine recycled concrete aggregates to partially or globally replace natural fine aggregates (sand) in the production of structural concrete. To evaluate the viability of this process, an experimental campaign was implemented in order to monitor the mechanical behaviour of such concrete. The results of the following tests are reported: compressive strength, split tensile strength, modulus of elasticity and abrasion resistance. From these results, it is reasonable to assume that the use of fine recycled concrete aggregates does not jeopardize the mechanical properties of concrete, for replacement ratios up to 30%.     

Effect of natural coarse aggregate type on the physical and mechanical properties of recycled coarse aggregates

Many environmental problems caused by the large volumes of construction and demolition waste (C&DW), the lack of adequate deposition sites and the shortage of natural resources have led to the use of C&DW as replacement of natural aggregates in the production of new concrete. As in the case of natural aggregates, when recycled aggregates are used to manufacture structural concrete, the assessment of their physical, mechanical and durable characteristics is a key issue. The different physical and mechanical properties of the recycled coarse aggregate (RCA) are evaluated. RCA was obtained by crushing conventional concretes with different strength levels (different w/c ratios) containing four different types of natural coarse aggregates (three crushed stones and a siliceous gravel), which differ in shape, composition and surface texture. There is a significant influence of the natural coarse aggregate (NCA) on the properties of RCA, which in many cases is greater than that of the w/c ratio of the source concrete.     

Creep and drying shrinkage characteristics of concrete produced with coarse recycled concrete aggregate

Laboratory tests are performed to investigate the effects of a new method of mixture proportioning on the creep and shrinkage characteristics of concrete made with recycled concrete aggregate (RCA). In this method, RCA is treated as a two component composite material consisting of residual mortar and natural aggregate; accordingly, when proportioning the concrete mixture, the relative amount and properties of each component are individually considered. The test variables include the mixture proportioning method, and the aggregate type. The results show that the amounts of creep and shrinkage in concretes made with coarse RCA, and proportioned by the new method, are comparable to, or even lower than, those in similar concretes made entirely with natural aggregates. Furthermore, it is demonstrated that by applying the proposed “residual mortar factor” to the existing ACI and CEB methods for calculating creep or shrinkage of conventional concrete, these methods could be also applied to predict the creep and shrinkage of RCA-concrete.     

Assessment of mechanical properties of concrete incorporating carbonated recycled concrete aggregates

An accelerated carbonation technique was employed to strengthen the quality of recycled concrete aggregates (RCAs) in this study. The properties of the carbonated RCAs and their influence on the mechanical properties of new concrete were then evaluated. Two types of RCAs, an old type of RCAs sourced from demolished old buildings and a new type of RCAs derived from a designed concrete mixture, were used. The chosen RCAs were firstly carbonated for 24 h in a carbonation chamber with a 100% CO₂ concentration at a pressure level of 0.1 Bar and 5.0 Bar, respectively. The experimental results showed that the properties of RCAs were improved after the carbonation treatment. This resulted in performance enhancement of the new concrete prepared with the carbonated RCAs, especially an obvious increase of the mechanical strengths for the concrete prepared with the 100% carbonated new RCAs. Moreover, the replacement percentage of natural aggregates by the carbonated RCAs can be increased to 60% with an insignificant reduction in the mechanical properties of the new concrete.     

Influence of field recycled coarse aggregate on properties of concrete

This paper investigates the influence of different amounts of recycled coarse aggregates obtained from a demolished RCC culvert 15 years old on the properties of recycled aggregate concrete (RAC). A new term called “coarse aggregate replacement ratio (CRR)” is introduced and is defined as the ratio of weight of recycled coarse aggregate to the total weight of coarse aggregate in a concrete mix. To analyze the behaviour of concrete in both the fresh and hardened state, a coarse aggregate replacement ratio of 0, 0.25, 0.50 and 1.0 are adopted in the concrete mixes. The properties namely compressive and indirect tensile strengths, modulus of elasticity, water absorption, volume of voids, density of hardened concrete and depth of chloride penetration are studied. From the experimental results it is observed that the concrete cured in air after 7 days of wet curing shows better strength than concrete cured completely under water for 28 days for all coarse aggregate replacement ratios. The volume of voids and water absorption of recycled aggregate concrete are 2.61 and 1.82% higher than those of normal concrete due to the high absorption capacity of old mortar adhered to recycled aggregates. The relationships among compressive strength, tensile strengths and modulus of elasticity are developed and verified with the models reported in the literature for both normal and recycled aggregate concrete. In addition, the non-destructive testing parameters such as rebound number and UPV (Ultrasonic pulse velocity) are reported. The study demonstrates the potential use of field recycled coarse aggregates (RCA) in concrete.     

Mechanical and durability properties of concrete using contaminated recycled aggregates

The degradation of concrete structures due to chlorides and sulphates penetration is of obvious importance in civil engineering as having major impact on structural durability. In this paper, the results of an investigation on the effect of contaminated crushed concrete aggregates on mechanical properties and durability of recycled concrete are presented. Natural aggregates concrete (NC) slabs were cured in water, sea water, chloride solutions or sulphate solutions and then crushed to obtain virgin and contaminated (polluted) recycled aggregates. The properties of natural (NA) and recycled aggregates (RA) and the mechanical properties and durability performances of a new concrete made from 100% of RA are analysed. The results show that contaminated RA are much sensitive to chlorides than sulphates and are rapidly leached when soaked into water. Significant differences were observed between the properties of original and new concrete and the results clearly show the necessity of taking these contaminations into account.