首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 156 毫秒
1.
The formation of plasma bullets’ring-shaped structure in atmospheric pressure helium is analyzed by using a coupled fluid model.The model consists of a two-dimension neutral gas flow module and a one-dimension plasma dynamics module.The obtained radial distributions of the electron’s number density and the nitrogen’s metastable number density have different structures under different types of reactions or air contents in the model.It shows that total electron impact ionization plays an important role in sustaining the discharge,and together with Penning process,they lead to the shifted-off structure of electron number density.Meanwhile,the ring structure of plasma bullets forms mainly due to the excitation reaction of nitrogen molecule on air contents.  相似文献   

2.
Foam fracturing is an important technology in the development of low permeability oil/gas reservoirs. The heat transfer characteristics of foam fracturing fluid are directly relevant to the calculation of pressure drop in the well, the optimum choice of fracturing parameters and the accurate evaluation of fracturing results. CO2 foam fracturing fluid behaves as a non-Newtonian fluid. The convective heat transfer characteristics of CO2 foam fracturing fluid were experimentally investigated on the newly constructed large-scale test loop under downhole conditions with CO2 in supercritical state, the pressure up to 40MPa. From the test data, corresponding correlations for convective heat transfer were obtained and the influences of pressure, temperature and flow rate were also studied. The convective heat transfer coefficient increased with the increase of temperature and flow rate, while the effect of pressure was much more complicated. In most cases, with the increase of pressure the coefficient tended to decrease.  相似文献   

3.
The negative DC corona discharge in air at atmospheric pressure was investigated in a needle-to-water system to obtain the pressure distribution of corona ionic wind.The deformation of water surface was measured and the distribution of wind pressure over the water surface was calculated.The effects of varying discharge parameters,such as applied voltage,gap spacing,tip radius of needle,and the shape of grounded electrode,on the wind pressure were studied.The measured wind pressure ranges from several Pa to several tens of Pa and up to 33 Pa over a small area;the pressure is comparatively large in the center and decreases quickly outwards.In the experiment system,a higher voltage on a 3 mm gap resulted in a stronger pressure of the ionic wind;around the onset voltage,using a needle with tip radius of 50μm obtained a larger wind pressure than using a needle with 100μm tip radius,but the latter one can produce larger pressure at higher voltages.Plus,the shape of the grounded electrode only influences the wind pressure a little.  相似文献   

4.
The valve side windings of converter transformers bear AC, DC, impulse, and reversal-polarity voltages during operation, which could result in serious insulation problems of the equipment. By performing experiments with surface discharge model of oil-paper insula- tion at 80 ℃ under combined AC-DC voltage for 200 h, we studied the spectrums and statistical parameters of partial discharges at different discharge stages. Furthermore, some fingerprint parameters were calculated in order to estimate the development situation of par- tial discharge, while the characteristic gases dissolved in the transformer oil were measured by gas chromatography. The surface discharges in the experiments were observed using a high speed camera, and a full discharge process could be marked off into four stages as follows. ①The elementary stage. When a partial discharge occurs near electrodes, electrical charges are injected into the region near electrodes and causing bubble generation. ②Due to their high resistivity and low dielectric constant, the bubbles would bare the major part of the voltage applied to samples. Therefore, discharge happens inside the small bubbles, and it emits a lot of light. ③Micromolecules of gas are produced in discharge, and further ionization in the transformer oil takes place simultaneously when high-energy electrons collide with oil molecules. ④The carrier charge moves forward to electrodes driven by the applied electric field, till they neutralize with the charge from electrodes, and hence discharge channels are formed subsequently.  相似文献   

5.
In order to study electromagnetic field coupling to irregular cuboid enclosures,tests of shielding effectiveness are performed using a hollow irregular truncated pyramid with a square aperture.The electric field distribution inside the enclosure with different sizes of the square aperture is measured within the frequency range of 5~1 000 MHz.The experimental results are in a good agreement with the stimulation results obtained by using computer simulation technology(CST)code.It is shown that the aperture size affects shielding effectiveness at low frequencies,at which shielding effectiveness decreases with the decreasing aperture size.The effect of the aperture size vanishes and shielding effectiveness improves by more than 12 dB when polyurethane absorbent fills the enclosure.  相似文献   

6.
Non-thermal plasma jet at atmospheric pressure has recently attracted lots of attention because of its applications in plasma bullet or plasma plume.Thus,we studied on generating plasma jet by coplanar dielectric barrier discharge in a device driven by sinusoidal voltage.The processes of plasma discharges in both positive and negative half cycles were recorded using a high-speed ICCD(intensified charge-coupled device)camera;based on the results we estimated the velocity of plasma propagation,and investigated the influence of gas flow on the plasma development.It is shown that the plasma bullets,which have velocity in the order of 103~104m/s,exist only outside the cathode.APPJ(atmospheric pressure plasma jet)is created by the electron beam from the cathode,and then sustained by a strong radial electric field near and outside the cathode.The gas flow influences the APPJ length in air but not the APPJ discharge,while the discharge is affected significantly by the applied voltage.  相似文献   

7.
This paper presents a method for determining specific models of overhead power lines with presence of corona phenomenon. The obtained models provide stable numerical solutions for computer simulation of transients caused by direct lightning strikes. The corona non- linear charge-voltage characteristics obtained from experimental tests are used for identification of the corona parameters based on System Identification Toolbox implemented in Matlab package. Different transfer functions, which give the same waveshapes of overvoltages are de- termined using two parametric models. A circuit representation of the obtained transfer functions is proposed and the corona model is implemented in the EMTP-RV as a hierarchical structure composed of a overhead power line divided into sections with corona branches. Some computer simulations of lightning overvoltages propagated in a typical 220 kV power line due to direct lightning strikes to a line tower are presented. The proposed method and the model implemented in EMTP-RV are still valid for multi-conductor lines and for higher voltages of power lines but new corona nonlinear charge-voltage characteristics are required as an input parameter for the identification procedure.  相似文献   

8.
林莘  曹辰  李斌  刘洋  徐建源 《高电压技术》2013,(7):1772-1777
In order to research the dynamic characteristics of circuit breaker(CB) in opening process,taking a 12kV vacuum circuit breaker(VCB) with permanent magnetic actuator as the example,a dynamic model of the VCB is established based on the virtual prototype technology,and dynamic equations of the model are deduced.Simulation and experiment are carried out on the VCB of both opening and closing processes.The simulative opening time and closing time are 39.5ms and 54.6ms respectively.Influencing factors of opening bouncing and their effect principles are analyzed through dynamic simulations of opening bouncing process.Analytic results indicate that the increase in the stiffness coefficient of contact spring limits the opening bouncing;meanwhile increases in the preload of contact spring and the mass of shaft can enlarge the opening bouncing.  相似文献   

9.
Alkylation of methylnaphthalene with methanol is one promising technology for producing 2,6-dimethylnaphthalene. When the alkylation is carried out under ambient pressure by using HZMS-5 catalysis, the reaction activity is very low and obvious deactivation of catalyst is observed in a short run.This paper aims at slowing down catalyst deactivation and improving reaction activity of alkylation of methylnaphthalene with methanol by taking advantage of some special properue: of supercritical fluids,such as higher solubility than gases and higher diffusivity than liquids. The results indicate that the reaction under supercritical condition will achieve high reaction activity and long catalyst life. When the reaction was carried out at 460℃ and 7.0MPa which is above the critical temperature and pressure of the inert reaction solvent, 1,3,5-trimethylbenzene, the reaction activity increased by 3 times and catalyst life was extended by 25 to 30 times than those under ambient pressure and at the same temperature.  相似文献   

10.
Before diagnosed by DGA (dissolved gas analysis) methods, gas caution values, which index the level of gas formation, must be used to evaluate the possibility of incipient faults to reduce the misdiagnosis in the normal state. However, the calculation of these values is now only based on cumulative percentile method without taking into account operating conditions. To overcome this disadvantage, a new approach to calculate the transformer caution values is presented. This approach is based on statistical distribution and correlation analysis, and it takes the individual variation and fluctuation caused by internal and external factors into consideration. Then 6550 transformer DGA data collected from North China Power Grid are analyzed in this paper. The results show that the volume fraction of TH (total hydrocarbon) approximately obeys normal distribution when the 3-sigma rule is used to calculate its caution value. The volume fraction of CO has a strong positive correlation with oil temperature. For H2, the negative correlation with oil temperature is significant when the volume fraction is not very low. The caution value curves for CO and H2 are obtained by regression analyses. Thus, the gas caution values/curves obtained using the new method are not always constant, but vary with oil temperature, which is an advantage of the proposed method compared with cumulative percentile method. The variation of gas caution values/curves also reflects the influence of the external factors, for instance, va- rying with monitoring time ensures that the gas caution values are always consistent with operating status.  相似文献   

11.
An arc model considering deviations from thermodynamic and chemical equilibrium has been developed in order to achieve a better understanding of the arc plasma close to material surfaces.The model is based on unified consideration of the thermionic tungsten cathode,the arc region and the flat anode made of copper.The heat transfer within the electrodes is coupled with the plasma through the energy fluxes onto the electrode boundaries.Electrical characteristics of an 8 mm long free-burning arc are presented along with findings from spectroscopic measurements of the plasma emission in atmospheric pressure argon.The arc current varied from 60 A up to 200 A,and the gas flow rate was set at 12 L/min(at atmospheric pressure,room temperature).  相似文献   

12.
An experimental device is used to study the characteristics of dielectric barrier discharge(DBD)plasma excited by high voltage sub-microsecond pulse power in atmospheric air.Glass,polytetrafluoroethene(PTFE)and plexiglass are used as dielectric barrier materials.Comparatively homogeneous discharge is obtained within 130 mm diameter area in atmospheric air using the three dielectric materials with gap distances of 4.5 mm,6.5 mm and 6.5 mm,respectively.There is no filamentary discharge observed by naked eyes or by camera with the exposure time of 0.25 s.Gas gap voltage,discharge current,discharge power density,etc.are calculated by using Liu’s equivalent circuit model for pulsed DBD.These parameters are used to study the DBD characteristics.Typically,current varies from tens of amperes to hundreds of amperes in atmospheric air DBD excited by sub-microsecond pulses.The peak power can reach to MW order of magnitude.The average power surface density of 1.0 W/cm2and the average electron density of 1011cm 3can also be obtained in the discharge.Rotational and vibrational temperatures,approximately 400 K and 2 650 K,respectively,are obtained by using the emission spectrum of the discharge.This is the basic work performed for a better understanding of the characteristics of atmospheric air DBD plasma excited by high voltage sub-microsecond pulsed power source.  相似文献   

13.
伏进  杨庆  司马文霞 《高电压技术》2008,34(12):2542-2546
The operation data obtained abroad indicates that shielding failure in UHV transmission lines mostly accounts for the tripping-out accidents introduced by lightning striking the transmission line.Based on the discharge theories of long air gap and randomness theory,a leader progression model of lightning shielding failure is presented in this paper.The random characteristics of the downward and upward leader are simulated in this model.The ground slope angel is also considered in this model by using coordinate transformation.Moreover,the system voltage is also taken into consideration in this model.The simulation results show that the good agreement between this model and the field data.And the results suggest that return striking exist obviously in UHV transmission line.  相似文献   

14.
The design technology for HV SF6 gas circuit breakers is very demanding.A numerical method for prediction of the thermal interruption capability of SF6 gas circuit breakers is established based on the two-dimensional magneto-hydrodynamic(MHD) model and a commercial CFD(computational fluid dynamics) software,FLUENT.Nozzle ablation effect is considered by introducing an independent mass conservation equation for the ablated material to the overall conservation equations of mass,momentum,and energy.The ohmic heating and the radiation of the electric arc are considered in the model by adding relevant source terms.To predict the thermal interruption capability,the arc conductance 200 ns before current zero is used as an indicator.The CFD model is applied for the high current arcing phase,and Mayr arc model is used near the current zero period.The arc conductance at 200 ns before current zero(G200) for various arcing periods are computed by the present method.It shows that there exist a limit of the G200.For those whose arcing periods are within the arcing window,the related G200 are below the limit,therefore result a successful current interruption,and vice versa.The validation of the developed computer simulation tool is therefore verified.The numerical prediction by the simulation tool is verified by the direct interrupting test of 550 kV gas circuit breaker(GCB).The developed computer simulation tool was applied in the design of a 550 kV GCB.Significant benefits have been achieved in terms of both the cost saving and shorten of the development cycle.  相似文献   

15.
For atmospheric pressure plasma jets(APPJ),the gas temperature is essential for their applications.A spectral diagnosis of APPJ’s gas temperature is conducted in this work.The optical emission spectra of helium APPJ are captured by using an optical spectrometer system.Then,the grating secondary spectrum of OH(A2∑+(ν=0)→X2П(ν=0))are used to diagnose the gas temperature of plasmas because the spectrum has excellent resolution.Meanwhile,the vibrational temperatures are estimated by using the vibration sequence of N2band(SPS,the second positive system).On the basis of the method,some important conclusions were obtained.First,the spectral identifying indicates that the grating primary spectrum covers a whole wavelength range from 200 nm to 900 nm,and that the grating secondary spectrum overlaps with the primary spectrum from 400 nm to 900 nm.Second,the gas temperature(about 320 K)is close to the room temperature,while the vibrational temperature of the N2(SPS)is about 5 000 K.The trend of the two temperatures changing with the applied voltage is discussed in the end.  相似文献   

16.
The mechanism of micro-hollow cathode discharge at atmospheric pressure is investigated through simulations using two-dimensional fluid model combined with a transport model for metastable atoms.In the simulations,electric potential,electric field,particle density,and mean electron energy of the discharge are calculated.The results show that the two characteristic regions of the discharge,i.e.cathode drop and negative glow can be distinguished in the simulation.The cathode drop is characterized by strong electric field and high mean electron energy,while quasi-neutral plasma of high density and exists in the negative glow.The peak value of electron density can reach the order of 1017cm-3.The electron temperature varies from several eV to tens of eV.The influence of cathode dimension on the discharge characteristics is also investigated.  相似文献   

17.
A deep understanding of the physical processes coming along with the current interruption in high voltage circuit breakers is essential for the optimization of today’s switching technologies.Therefore a switching arc in a model circuit breaker is studied by means of computational fluid dynamics(CFD)simulations and optical emission spectroscopy(OES)in this contribution.Experimental investigations are performed in carbon dioxide(CO2)at absolute filling pressures of 0.1 and 0.5 MPa.CFD simulations are carried out based on a model of the arcing zone including a consistent treatment of the radiation transport and the wall ablation.Carbon ion line radiation is analysed in the experiment using an optical path in the heating channel between the electrodes inside the nozzle system.The pressure value in the arc is estimated based on the line width-intensity dependence.Obtained values correspond to the measured pressure outside the arc.For the temperature profiles,a good agreement within the accuracy of the approaches is observed between the CFD simulations and the results of OES.  相似文献   

18.
This paper is devoted to explanation of a phenomenon of current channels heads acceleration which bridges a discharge gap.This phenomenon was discovered experimentally during some works at investigating nanosecond streamer gas discharges of atmospheric pressure in the air and neon.Consideration of the bridging process of the discharge gap is presented in the framework of a model of microstructured current channel.In this case,the channel represents itself as a bunch of microchannels(up to 1 000 and more).Such consideration could be stipulated by the discovered earlier phenomenon of the current channels microstructuring that are realized in the nanosecond discharges of atmospheric pressure.The authors have developed the electro-technical model of the discharge gap bridging by the conducting channel.It is shown that the channel length dependence of the velocity is linear;this is similar to that of the model of the continuous(unstructured)channel.We considered and made estimations that stipulate a possibility of gas heating in the microchannels up to the temperatures of associative ionization beginning in the discharge gap bridging phase.In this case,increase of the charged particles concentration and,consequently,decrease of its resistance cause the head acceleration.It is shown that in case of the continuous channel it is impossible to realize the gas heating up to the temperatures of the associative ionization in these conditions.Obtained results reveal the physical reason of the current channels microstructuring as a consequence of the principle of least action manifestation in the area electric breakdown phenomena of the gases.  相似文献   

19.
Perfluorocyclobutane(c-C4F8) has been recently considered as a potential alternative to SF6,because of its high electro-negativity and extremely low environmental effect.However,due to its high boiling point,c-C4F8 should mixed with buffer gases such as N2 or CO2 in order to avoid the liquefaction at low temperature.This paper investigates insulating properties of c-C4F8/N2 gas mixtures from two aspects including electrical strength,and Global Warming Potential(GWP).Moreover,improved electrical breakdown model of gas mixtures is founded.Breakdown temperature and breakdown electrical field in gas mixtures can be obtained from rigorous Townsend criterion expression according to gas mixtures ratio and cross section data of gas mixtures in this model.Under the condition of different gas pressure(0.1~0.4 MPa),gas mixtures ratio(0~30%),and electrode gap(2~10 mm),breakdown voltages of gas mixtures are calculated by using of this model.Insulation strength of SF6/N2 mixed gas is compared with c-C4F8/N2 mixed gas in the same conditions.Research results show that theoretical computation corresponds with experiment.If the content of c-C4F8 or SF6 in mixtures is less than 30%,insulation strength between c-C4F8/N2 and SF6/N2 is very close.Considering two indexes(breakdown voltage,GWP),it is suitable for c-C4F8 content being 15%~20% in c-C4F8/N2 gas mixtures  相似文献   

20.
There was no well-resolved mechanism of audible noise caused by corona discharge on UHV transmission lines. Hence we measured the sound pressure of pulsed discharges between needle-plane electrodes under different discharge conditions in air, for revealing the intrinsic relationship between discharge and its audible noise(AN). The relationship between discharge parameters and audio characte- ristics was drawn from the analysis of the electric and sound signals obtained in experiments. Experiment results showed that nanosecond pulsed discharges produce the sound pressure with a microsecond pulse lagging behind the discharge pulse in their waveforms. The peak value of the sound pulse decreases and its high frequency component gradually attenuates, when the measuring distance from discharges increases. The sound pulses correlate with the discharge current and voltage significantly, especially the current. The audible noise produced by repetitive pulsed discharge increases with the strength, duration, and pulse repetition rate of discharge.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号