共查询到20条相似文献,搜索用时 62 毫秒
1.
2.
3.
4.
5.
以炭黑、石墨和镍粉等为导电填料,ABS和PETG作为高分子基体,采用熔融共混-模压成型工艺制备具有双连续相结构的质子交换膜燃料电池(PEMFC)用双极板。主要研究导电填料炭黑、石墨和镍粉等对ABS/PETG共混物的导电性、耐水性和耐热性能的影响。结果表明:当ABS和PETG为双连续相,炭黑为20%时,复合材料的导电性最好,为123S/m,玻璃化温度98℃,维卡软化温度123℃,接触角为100°。保持炭黑的含量为10%,通过调控石墨含量,发现当石墨含量在4%时,复合材料综合性能最好:电导率30S/m,玻璃化温度93℃,维卡软化温度107℃,接触角为103°。当保持15%炭黑的比例,镍粉含量为5%时得到最佳试样:电导率43S/m,玻璃化温度69℃,维卡软化温度150℃,接触角为89°。 相似文献
6.
7.
8.
测定了两种树脂对导电骨料的润湿性,研究了树脂及其含量对复合材料双极板性能的影响。采用对导电骨料浸润性好的树脂作粘合剂,通过模压一次成型技术制备出复合材料双极板的电导率大于300S/cm,抗折强度大于30MPa,空气透气率为10!7cm2/s。并进行了电堆组装及电性能和稳定性测试。结果表明,在较小的电流密度(<1.0A/cm2)条件下,复合材料双极板的电性能和石墨材料双极板相当,在较大的电流密度(>1.0A/cm2)条件下,其电性能要稍优于石墨材料双极板;电池经350h放电试验并重复启动电池100次以上,双极板性能稳定。 相似文献
9.
10.
11.
12.
特高压线路工频参数测试干扰分析是选择适合工频参数测试方法及测试结果分析的重要基础。测试了1 000 kV皖南-浙北特高压线路正序和零序参数测试期间的干扰电压信号,分析了其频谱特征;在此基础上,通过与正序参数仿真计算值的对比分析了正序参数实际测试偏差。结果表明:皖南-浙北特高压同塔双回线路工频参数测试期间,干扰电压存在“三相不平衡性及时变性”的特点;工频法和异频法2种不同方法得到的线路参数测试结果存在一定差异;干扰电压“时变”时,线路工频参数测试宜采用异频法。 相似文献
13.
《国外电子测量技术》2014,(10)
正Qingdao,China7.16-19,2015The International Conference on Electronic MeasurementInstruments(ICEMI)is the world’s premier conference dedicated to the electronic measurement and test of devices,boards and systems that is covering the complete cycle from design,verification,test,diagnosis,failure analysis and process of manufactory and products 相似文献
14.
《国外电子测量技术》2014,(9)
正Qingdao,China7.16-19,2015The International Conference on Electronic MeasurementInstruments(ICEMI)is the world's premier conference dedicated to the electronic measurement and test of devices,boards and systems that is covering the complete cycle from design,verification,test,diagnosis,failure analysis and process of manufactory and products 相似文献
15.
16.
17.
电站锅炉停用保护剂多采用十八胺和表面活性胺。对这2种停用保护剂进行了应用效果对比研究,即对湿冷机组、空冷机组采用十八胺或表面活性胺、有无凝结水精处理系统等6台机组停机和启动过程中给水、主蒸汽和凝结水的氢电导率变化情况进行分析。研究结果表明:在停机过程和启动过程,2种保护剂均会在水汽系统中发生部分分解,导致水汽系统的氢电导率显著升高;表面活性胺和十八胺比较,使用前者,机组启停机过程可保持凝结水精处理系统正常投运,因而可使水汽质量迅速达标,对机组安全运行有利,因此推荐采用表面活性胺作为锅炉停用保护剂。 相似文献
18.
S. Y. Wu B. N. Tran F. Y. Davis C. L. Trent D. L. Edberg W. A. Geideman 《Integrated ferroelectrics》2013,141(3):281-291
Abstract Smart materials of lead-zirconate-titanate (PZT) piezoelectric ceramics have attracted attention in recent years for active vibration control, acoustic noise suppression, health monitoring and damage assessment. We at McDonnell Douglas Aerospace have been studying these ceramics for use as sensors and actuators in various space and aircraft structures. In this paper, we will report results of a recent study on active vibration control using monomorph PZT actuators. The experiments were performed on thin aluminum cantilever beams. Collocated and non-collocated sensors and actuators were employed. Two control techniques: the classical velocity feedback and adaptive feedback controls, were investigated. We have obtained significant damping and broadband vibration attenuation of greater than 30 dB using the classical control with the single-input single-output feedback approach. A 24 dB reduction has also been achieved using the adaptive control with the multiple-input single-output approach. Detailed experimental methods and results will be described. 相似文献
19.
20.
全面、客观地对核一级锻件质量状况给予综合性评判,建立一套适用于锻件质量评价的方法体系很有必要。根据影响核一级锻件质量的制造工艺和成品质量检验,分析了影响锻件质量的主要工艺参数,建立了锻件质量评价的指标体系。在此基础上,探究了基于熵权的逼近理想解排序(TOPSIS)法的特点,建立了相应的评价模型,并将该模型应用于核电站反应堆堆芯筒体锻件的质量评价,获得了堆芯筒体质量状况的优劣排序。研究结果表明:TOPSIS法可有效、科学、客观地评价核一级锻件质量状况,且便于操作、易于推广使用。 相似文献