脉动流下棒束通道内相位差及瞬态流场研究

事故条件及海洋条件下反应堆处于非稳态工况,堆芯燃料组件内热工水力行为具有瞬变及多因素耦合特性,对反应堆的安全提出更高挑战,因此有必要对燃料组件内瞬态特性进行研究。本文通过测量棒状燃料组件内压降和流量之间延迟时间开展棒束通道脉动流条件下相位差研究,对比了相位差在不同振幅、不同流动状态下的变化特性,并分析了定位格架对脉动流相位差的作用特点。另外,基于粒子图像测速（PIV）技术开展了脉动流条件下棒束通道内流场分布特性研究,对比了相同流量条件下稳态工况与瞬态工况下流场分布差异,分析了主流具备不同加速度时棒束通道内流场分布特征。实验结果表明：定位格架可减小脉动流下棒束通道内相位差;棒束通道内流场演化滞后于主流量变化。实验结果有助于揭示燃料组件在非稳态条件下瞬态特性,并为燃料组件的设计和优化奠定基础。     

脉动流下棒束通道内相位差及瞬态流场研究

事故条件及海洋条件下反应堆处于非稳态工况,堆芯燃料组件内热工水力行为具有瞬变及多因素耦合特性,对反应堆的安全提出更高挑战,因此有必要对燃料组件内瞬态特性进行研究。本文通过测量棒状燃料组件内压降和流量之间延迟时间开展棒束通道脉动流条件下相位差研究,对比了相位差在不同振幅、不同流动状态下的变化特性,并分析了定位格架对脉动流相位差的作用特点。另外,基于粒子图像测速(PIV)技术开展了脉动流条件下棒束通道内流场分布特性研究,对比了相同流量条件下稳态工况与瞬态工况下流场分布差异,分析了主流具备不同加速度时棒束通道内流场分布特征。实验结果表明:定位格架可减小脉动流下棒束通道内相位差;棒束通道内流场演化滞后于主流量变化。实验结果有助于揭示燃料组件在非稳态条件下瞬态特性,并为燃料组件的设计和优化奠定基础。     

燃料试样堆内辐照温度设计与实验研究

为使燃料尽可能在最恶劣设计工况下进行辐照实验，开展基于高通量工程试验堆（HFETR）的燃料试样堆内辐照温度设计与实验研究。按照铀装量设计燃料试样在辐照装置内的位置，能够改善轴向燃料试样热流密度的不均匀性。HFETR主冷却剂低温状态下，在燃料试样外包覆液态铅铋合金和不锈钢能够实现燃料芯体及燃料包壳的高辐照温度指标。设计和实验结果表明，稳态和短期瞬态运行工况下，不锈钢盒表面辐照温度始终低于HFETR燃料元件包壳表面最高温度限值，满足反应堆运行和燃料辐照实验安全要求。为提高稳态运行工况下燃料试样的辐照温度，堆芯设计时应避免或降低由于反应性扰动造成的辐照装置内燃料试样短期瞬态功率影响，减小辐照孔道内燃料试样的热点因子。      

AFA 3G燃料棒芯块与包壳间相互作用分析

介绍了大亚湾核电站18个月换料策略下，在Ⅱ类工况瞬态期间AFA 3G燃料棒芯块与包壳间相互作用（PCI）的分析和预测。文中给出了PCI技术限值，介绍了Ⅱ类工况瞬态分析和热力机械分析的分析方法和程序，并给出了基荷运行、基荷加一次调频运行、负荷跟踪运行以及延伸低功率运行时的负荷过量增加、功率状态下控制棒失控抽出和未检测到的掉棒3种瞬态的PCI主要计算结果和结论。     

加/减速流动下棒束通道内速度分布和湍流特性研究

事故工况及海洋条件下反应堆处于非稳态工况,堆芯燃料组件内热工水力行为复杂多变,对反应堆安全提出了更高挑战,因此有必要对非稳态下燃料组件内流动换热特性开展研究。基于粒子图像测速（PIV）技术,结合远心镜头和脉冲控制器,实现对燃料组件内复杂流场的高时空分辨率、长时间的连续测量,获得了流量波动下燃料组件内时空演变的流场结构,分析了棒束通道内速度分布、湍流强度、雷诺应力等瞬时流场信息的空间演变特性。以定常流动下流场分布特性为基准,对比分析了加速度对燃料组件内空间流场分布的贡献特点。实验结果表明：加速流动提高了棒束通道内流层之间的速度梯度,抑制了横向速度和湍流强度;减速流动减弱了棒束通道内流层之间的速度梯度,提高了横向速度和湍流强度。实验结果有助于揭示燃料组件在非稳态条件下的瞬态特性,并为燃料组件的设计和优化奠定基础。     

快堆燃料组件的子通道分析

开发了ＴＨＡＳ－ＰＣ２子通道分析微机程序，用于计算稳态和瞬态工况下快堆燃料组件的流量、温度和压力等参量分布。对ＥＦＲ燃料组件的稳态和瞬态计算结果如下：堆芯出口平均温度和温长分别为５５７℃和１５７℃，最高包壳表面温度为６０１℃，它发生在中心燃料棒上，最大冷却剂温度为５９３℃；主泵断电二次停堆事故作为瞬态计算，算得的最高冷却剂温度和最高包壳表面温度分别为６３０℃和６３７℃（当ｔ＝２ｓ时），它们都远低于     

高燃耗下UN-FeCrAl燃料元件稳态及瞬态热力学性能分析

UN-FeCrAl燃料元件作为耐事故燃料高燃耗应用的主要方案之一,需要评价其在高燃耗下的热力学性能。本研究基于FUPAC软件对UN-FeCrAl燃料元件在燃耗68000 MW·d·t^-1(U)下的稳态和瞬态热力学性能进行了预测。分析结果表明,稳态工况下UN-FeCrAl燃料元件热力学性能表现良好;瞬态下UN燃料的芯块中心温度最高仅为862℃,可满足芯块温度设计要求,但FeCrAl包壳的瞬态应力最大将达到459 MPa,且瞬态应变量相比于稳态应变量最大增加了0.23%,这可能会使FeCrAl包壳面临瞬态应力和瞬态应变准则超限的风险。因此后续研究应重点关注FeCrAl包壳的瞬态应力和瞬态应变性能。     

船用堆燃料棒包壳疲劳寿命分析

船用堆瞬态变工况下燃料棒包壳温度和冷却剂压力波动较大,引起包壳的疲劳损伤,因此包壳疲劳寿命分析至关重要。本文利用ANSYS软件模拟船用堆瞬态变工况下燃料棒的热机械行为,结合锆包壳疲劳寿命设计曲线,考察包壳温度、冷却剂压力、燃料棒内压以及辐照对船用堆燃料棒包壳疲劳寿命的影响。计算结果表明,瞬态变工况使得包壳疲劳寿命有很大降低;包壳温度变化与冷却剂压力变化相比,前者对包壳疲劳寿命的影响小;辐照会降低包壳疲劳寿命。在不影响核动力船舶机动性的前提下,可采取一些必要的措施来降低包壳的疲劳损伤。     

事故容错燃料安全性能初步分析

事故容错燃料（ATF）是通过提高燃料材料热物性或包壳材料抗高温氧化性能来加强核燃料的事故容错能力,从而使核燃料能长期忍受严重事故。使用二次开发适用于ATF的RELAP5程序,对UO₂-FeCrAl、FCM-FeCrAl这两种ATF和传统核燃料UO₂-Zir-4进行大破口失水事故安全分析。对比事故分析结果可知：相较于传统UO₂芯块,稳态运行工况下,热导率高的FCM芯块具有更低的燃料中心温度和更小的燃料径向温度梯度,同时在瞬态事故工况下,FCM芯块具有更低的瞬态初始温度和更小的燃料温度增长速率。相较于传统Zir-4包壳,在瞬态事故工况下,FeCrAl的包壳峰值温度更小,达到的时间更晚,同时由于FeCrAl包壳具有良好的抗高温氧化性能,事故过程中产生的氢气质量更小。     

事故容错燃料安全性能初步分析

事故容错燃料(ATF)是通过提高燃料材料热物性或包壳材料抗高温氧化性能来加强核燃料的事故容错能力,从而使核燃料能长期忍受严重事故。使用二次开发适用于ATF的RELAP5程序,对UO_2-FeCrAl、FCM-FeCrAl这两种ATF和传统核燃料UO_2-Zir-4进行大破口失水事故安全分析。对比事故分析结果可知:相较于传统UO_2芯块,稳态运行工况下,热导率高的FCM芯块具有更低的燃料中心温度和更小的燃料径向温度梯度,同时在瞬态事故工况下,FCM芯块具有更低的瞬态初始温度和更小的燃料温度增长速率。相较于传统Zir-4包壳,在瞬态事故工况下,FeCrAl的包壳峰值温度更小,达到的时间更晚,同时由于FeCrAl包壳具有良好的抗高温氧化性能,事故过程中产生的氢气质量更小。     

Preparation of Zn/TiO2 powder and its photocatalytic performance for oxidation of P-nitrophenol

Zn-doped TiO2 catalysts were prepared using a sol-gel method and characterized by XPS,UV-Vis, BET, XRD in this study. Under the irradiation of simulant sunlight, the photocatalytic activity for the degradation of p-nitrophenol was studied too. After irradiation for 2.5 h, the degradation percentage of p-nitrophenol could rise to more than 80 %. The results showed that the spectrum absorption band edge of Zn/TiO2 powder does not broaden obviously comparing with pure TiO2 powder. Zinc exists as Zn （11）. When calcined at 973 K, there is a new phase as ZnTiO3 in Zn/TiO2 catalyst. The order of photocatalytic activity of Zn/TiO2 catalysts calcined at different temperatures for p-nitrophenol is 773 K 〉 673 K 〉 873 K 〉 573 K 〉 973 K and the photocatalytic activity of Zn/TiO2 catalyst calcined at 773 K is better than TiO2 catalysts heated at the same temperature, and outclasses that of commercial TiO2 catalyst. It also showed that the photocatalytic degradation of p-nitrophenol follows first-order kinetics under the irradiation of simulant sunlight.     

Current status of radiation therapy for prostate cancer

Radiotherapy for the treatment of prostate cancer has been extensively explored in the past. Along with the comprehensive understanding of the biology of prostate cancer and rapid advances in terms of technology, the out- come of treatment for the patients with prostate cancer has improved. The authors review radiotherapy as the primary treatment for the disease, with particular emphasis on the technological advances from both the radiobiological and radiophysics aspects. Nonconventional fractionated irradiation like hyper- or hypo-fractionation has been imple- mented in the clinic, the final results still need to be confirmed in the future. Technological advances like IMRT, IGRT, in the last two decades have significantly improved the delivery of external radiotherapy to the prostate. This has re- sulted in an overall increase in the total dose that can be safely delivered to the prostate, which has led to modest im- provements in the biochemical outcome. However, establishing the standard therapy for prostate cancer remains con- troversial. It is hoped that the next decades will bring continued advances in the development of biologicals that will further improve current clinical outcomes.     

The control system for SSRF injection and extraction

This paper introduces the injection and extraction control system design for SSRF,which is a distributed control system aimed at stability and reliability of the pulse power supplies,PPS(Personnel Protection System)and MPS(Machine Protection System).The hardware environment is mainly based on PLC(Programmable Logic Con- troller),and ARM(Advanced RISC Machine)is also applied for studying stability of the power supplies.WinCC and EPICS(Experimental Physics and Industrial Control System)have been selected as the platforms of SCADA(Super- visory Control and Data Acquisition).For unifying the interfacing to the control computer,all front-end equipments are connected via Industrial Ethemet.     

水平管内含空气蒸汽强制对流冷凝换热模型研究

为研究含空气蒸汽在水平管内强制对流冷凝换热特性,基于对传热传质过程的分析,建立了管内为环状流与波状流条件下的流动冷凝换热模型。从潜热、显热和液膜3个环节对整个换热过程进行建模,最终得到计算局部冷凝换热系数的理论关系式。模型预测结果与实验数据的对比表明,二者相对偏差在±20%以内,验证了该换热模型的准确性与适用性。通过进一步的研究发现：从换热管入口至出口,随着冷凝的进行,管内换热主要热阻由液膜热阻向气液界面的凝结热阻转变;主流气体对流换热过程基本可忽略。     

Investigations on landmine detection by BF3 detector

Experiments were carried out to investigate the possible use of neutron backscattering for the detection of polyethylene (PE) sample buried in the soil. In detection of landmine by neutrons, the neutron detector and its shield play an important role. In this paper, the effects of graphite, heavy water, polyethylene and boric acid moderators on the flux of back scattered neutrons were investigated. We have also experimentally verified the effect of BF3 detector shield and obtained good agreement with theory.     

Web Services interface of SSRF archive data analysis system

Accelerator database stores various static parameters and real-time data of accelerator. SSRF (Shanghai Synchrotron Radiation Facility) adopts relational database to save the data. We developed a data retrieval system based on XML Web Services for accessing the archive data. It includes a bottom layer interface and an interface applicable for accelerator physics. Client samples exemplifying how to consume the interface are given. The users can browse, retrieve and plot data by the client samples. Also, we give a method to test its stability. The test result and performance are described.     

有效探测面积大于1000 cm2的正比计数器测量系统性能测试

为对自制的活性面积高达1 000 cm²的大面积源进行表面发射率定值,同时作为现有2πα、2πβ表面发射率标准装置能力的扩充,研制了一套内置式大面积2π多丝正比计数器测量系统,并利用活性区直径为8 mm的²⁴¹Am点源及活性区面积为10 cm×15 cm的大面积²⁴¹Am和⁹⁰Sr-⁹⁰Y源对其进行计量学性能测试。结果表明：计数器内计数响应均匀性优于±0.4%,有效探测面积达1 400 cm²;所得²⁴¹Am源高压坪曲线的坪长为1 400 V,坪斜为0.27%/100 V,坪区内计数变化为0.87%;⁹⁰Sr-⁹⁰Y源高压坪曲线的坪长为300 V,坪斜为0.75%/100 V,坪区内计数变化为0.80%;10次测量重复性好于0.4%,8 h内短期稳定性好于0.3%,1 a内长期稳定性好于0.8%。     

Assessment of radioactivity levels in some oil samples from the western desert, Egypt

Distributions of natural gamma-emitting radionuclides were determined in 93 oil samples collected from some petroleum fields in the western desert of Egypt. The radioisotope activities in the area under investigation lay in the range of (21 ± 4) to (38 ± 13) Bq?L-1 for 226Ra, (9 ± 2) to (15 ± 5) Bq?L-1 for 232Th, and (154 ± 28) to (303 ± 54) Bq?L-1 for 40K. The mean values were 27, 12, and 201 Bq?L-1, respectively. Among oils, variations in radionuclide ac- tivities could be on account of differences in TDS, HCO3, and Ba, with high or low pH. In this environment, oil prop- erties differently affected the mobilization of natural radionuclides. The range of 226Ra variation had been compared with available data from other countries. The calculated absorbed dose rate ranged from 22.33 to 32.66 nGy?h-1 in lo- cation (B) and (E) respectively, which was less than the accepted value.     

Preparation and properties of 117m Sn(IV)-TTHMP in in-vitro and in small animals

In this work,TTHMP was synthesized and labelled with 117m Sn.The preparation conditions,stability and lipophilicity of 117m Sn(IV)-TTHMP were investigated.Biodistribution of the complex in rabbits and mice was studied.It was found that the quantity of TTHMP and pH value of the prepararion solution had vital effects on the labeling yield of 117m Sn(IV)-TTHMP.It was also found that 117m Sn(IV)-TTHMP was hydrophilic and stable at room temperature and 37℃ in open air 117m Sn(IV)-TTHMP showed unexpectedly high bone uptake and bone-to-blood ratio in the animals.This made it potentially useful as an reagent for skeletal scintigraphy and radiotherapy of bone tumors.     

The role of AGFA high-energy CR in the calibration and quality control of multileaf collimators （MLC）

Linear accelerators equipped with multileaf collimators （MLC） are becoming more common and are widely used in the intensity-modulated radiotherapy （IMRT）. There is an imperative need to ensure the commissioning specification of the linear accelerators for the sake of quality assurance （QA） and quality control （QC）. This paper is aimed to investigate the role of AGFA high-energy CR （Computed Radiography） in calibrating dynamic multileaf collimators and evaluating the accuracy of the leaf position. The result shows that AGFA high-energy CR can easily and conveniently be used to calibrate MLC and verify its position. Hence, the application of AGFA high-energy CR is proved to be an accurate and time-saving method for routine MLC QC, especially when MLC calibration adjustments are required.