Microstructure and mechanical properties of dissimilar materials joints between T92 martensitic and S304H austenitic steels

In this paper, T92 martensitic steel and S304H austenitic steel were welded by gas tungsten arc welding (GTAW) process. Microstructural features and mechanical properties of T92 and S304H dissimilar materials joints were investigated. The results showed that the part of the joints with relatively weak tensile strength was T92 coarse-grained heat affected zone (CGHAZ), while the part of the joints which revealed relatively weak toughness was weld metal. The decrease of tensile strength in T92 CGHAZ was due to its coarse tempered martensite structure. Weak toughness of the joints was resulted from the coarse dendritic austenite of the weld metal. However, the weld metal in transverse direction of the joints was provided higher tensile strength by the orientation distribution of grains compared with T92 CGHAZ.     

Microstructures and mechanical properties of T92/Super304H dissimilar steel weld joints after high-temperature ageing

T92/Super304H dissimilar steel weld joints, fabricated through a gas tungsten arc welding (GTAW) technique using a Ni-based welding wire of ERNiCrMo-3, were aged at 650 °C for time up to 3000 h. Microstructures, fractographies and mechanical properties of the joints were then investigated. The results show that as the aging time increased, in the T92 side heat-affected zone (HAZ) and base metal (BM), the second-phase particles aggregate and coarsen along the austenite grain boundaries/in the austenite grains. In the Super304H side HAZ and BM, the growth of the austenite grains and that of the second-phase particles are slight. The fracture positions of the aged joints are always in the T92 BM. The tensile strengths and the hardness values of the joints drop firstly, then rise, and finally tend to be stable. The impact toughness values of the joints are monotonously decreases with the ageing time.     

Effect of heat input on microstructure and mechanical properties of dissimilar joints between super duplex stainless steel and high strength low alloy steel

In the present study, microstructure and mechanical properties of UNS S32750 super duplex stainless steel (SDSS)/API X-65 high strength low alloy steel (HSLA) dissimilar joint were investigated. For this purpose, gas tungsten arc welding (GTAW) was used in two different heat inputs: 0.506 and 0.86 kJ/mm. The microstructures investigation with optical microscope, scanning electron microscope and X-ray diffraction showed that an increase in heat input led to a decrease in ferrite percentage, and that detrimental phases were not present. It also indicated that in heat affected zone of HSLA base metal in low heat input, bainite and ferrite phases were created; but in high heat input, perlite and ferrite phases were created. The results of impact tests revealed that the specimen with low heat input exhibited brittle fracture and that with high heat input had a higher strength than the base metals.     

High-temperature tensile and creep deformation of cross-weld specimens of weld joint between T92 martensitic and Super304H austenitic steels

The high-temperature mechanical behavior of cross-weld specimens prepared from a dissimilar weld joint between T92 martensitic and Super304H austenitic heat-resistant steels incorporating Ni-based weld metal was evaluated at temperatures up to 650 °C. For both high temperature tensile and creep tests, failure took place in T92 due to its faster degradation with temperature increase. The heat-affected zone of T92 played a critical role during creep deformation, resulting in type IV failure under the long-term creep condition. For the creep specimens, the location of failure shifted from the base metal region to the fine-grained heat-affected zone as the creep duration time increased from the short-term to the long-term condition. The massive precipitation of Laves phase on the grain boundaries of the fine-grained heat-affected zone during creep deformation was observed and found to be responsible for the accelerated void formation in the area leading to the premature failure.     

Investigation on microstructure,mechanical properties and corrosion behavior of AISI 316L stainless steel to ASTM A335-P11 low alloy steel dissimilar welding joints

In the present study, the microstructure, mechanical properties and corrosion resistance of AISI 316L austenitic stainless steel to ASTM A335-P11 low alloy steel dissimilar joints, which are widely employed in the oil and gas industries especially for manufacturing of heat exchangers over 600°C, were investigated. For this purpose, two filler metals of ER309L and ERNiCrMo-3 were selected to be used with GTAW process. The results of microstructural evaluation revealed that the ERNiCrMo-3 weld metal contains dendritic and interdendritic zones, and the ER309L weld metal microstructure includes skeletal ferrites in an austenitic matrix. The maximum impact fracture energy and microhardness values were obtained for the ERNiCrMo-3 weld metal specimens; however, no significant difference was observed between the tension properties. The corrosion test results showed that the ERNiCrMo-3 has a higher corrosion resistance than ER309L. Finally, it was concluded that ERNiCrMo-3 would be a suitable filler metal for joining AISI 316L to A335-P11 for a variety of applications.     

Microstructures and mechanical properties of welded joints of novel 3Cr pipeline steel using an inhouse and two commercial welding wires

The welded joints of the novel 3Cr pipeline steel were fabricated via the gas tungsten arc welding (GTAW) technique using an inhouse welding wire labeled as R01 and two kinds of commercial wires (H08Cr3MoMnA and TGS-2CML). Microhardness, impact toughness and tensile properties of the joints were measured, and microstructure characteristics were observed by scanning electron microscopy (SEM). The results show that under selected welding procedure, the joints of R01 can achieve quite good mechanical properties without preheating and post weld heat treatment (PWHT). After thermal refining, elongation (15.2%) doubled and met the DNV-OS-F101 standard. For low carbon or super low carbon pipeline steels such as 3Cr steel, the revised formula with the carbon applicable coefficient (A(c)) was quite good for predicting the maximum hardness in heat affected zone (HAZ). Compared with these two selected commercial wires, the inhouse welding wire R01 can provide the highest cost-performance ratio.     

Interface microstructure evolution of dissimilar friction stir butt welded F82H steel and SUS304

The dissimilar butt welded joint of reduced-activation ferritic/martensitic steel (RAF/M) F82H and austenite stainless steel (AISI304 (SUS304)) were studied by friction stir welding. The effect of the position of the steels and tool plunging was considered in order to prohibit the mixing of the F82H and SUS304. When the dissimilar butt welding was performed such that the F82H plate was on the advancing side and the tool was plunged on the F82H side, defect-free joints could be successfully fabricated. Optical microscopy and EDX analysis were used to characterize the dissimilar joint microstructures and the interface. It was confirmed that the dissimilar joint formed no mixed structure and inter-metallic compounds.     

T92/Super304H异种钢焊接接头的性能研究

根据新型耐热钢T92和Super304H钢的焊接特点制定了适宜的焊接工艺,研究了焊制的T92/Su-per304H异种钢焊接接头的力学性能。结果表明,T92/Super304H异种钢接头的各项力学性均能满足使用要求。焊缝金属的韧性远低于T92钢侧热影响区,焊缝金属的结晶形态对焊缝韧性有很大的影响。焊接接头中焊缝金属的硬度值最高,而T92钢侧热影响区硬度最低,并且不同热影响区部位显微硬度变化较大,Super304H钢侧热影响区硬度变化不大。     

Assessment of creep rupture properties for dissimilar steels welded joints between T92 and HR3C

Dissimilar steels welded joints, between ferritic steel and austenitic stainless steel, are always encountered in high‐temperature components in power plants. As two new grade ferritic steel and austenitic stainless steel, T92 (9Cr0.5Mo2WVNb) and HR3C (TP310HCbN), exhibit superior heat strength at elevated temperatures and are increasingly applied in ultra‐supercritical (USC) plants around the world, a complete assessment of the properties for T92/HR3C dissimilar steels welded joints is urgently required. In this paper, metallographic microstructures across the joint were inspected by optical microscope. Particularly, the creep rupture test was conducted on joints under different load stresses at 625 °C to analyse creep strength and predict their service lives, while their fractograph were observed under scanning electron microscope. Additionally, finite element method was employed to investigate residual stress distribution of joints. Results showed that the joints were qualified under USC conditions, and T92 base material was commonly the weakest part of them.     

Microstructure and intergranular stress corrosion cracking susceptibility of a SA508-52M-316L dissimilar metal weld joint in primary water

Correlation of microstructure and intergranular stress corrosion cracking (IGSCC) susceptibility for the SA508-52M-316L dissimilar metal weld joint in primary water was investigated by the interrupted slow strain rate tension test following a microstructure characterization. The susceptibility to IGSCC in various regions of the dissimilar metal weld joint was observed to follow the order of Alloy 52 Mb> the heat affected zone of 316L> the dilution zone of Alloy 52 Mw> Alloy 52 Mw weld metal. The chromium-depletion at the grain boundary is the dominant factor causing the high IGSCC susceptibility of Alloy 52 Mb. However, IGSCC initiation in the heat affected zone of 316L is attributed to the increase of residual strain adjacent to the grain boundary. In addition, the decrease of chromium content and increase of residual strain adjacent to the grain boundary increase the IGSCC susceptibility of the dilution zone of Alloy 52 Mw.     

Formation of the anomalous microstructure in the weld metal of Co-based alloy/AISI 410 stainless steel dissimilar welded joint

The Co-based alloy/AISI 410 stainless steel dissimilar welded joint was fabricated by the electron beam welding (EBW) technique. The anomalous microstructure containing the element transition zone (ETZ) and/or core of tail-like zone (CTLZ) is in the weld metal (WM) adjacent to the fusion line. The melting temperature difference between the WM and AISI 410 steel, melt stirring effect and element diffusion can trigger the formation of such anomalous microstructure. In particular, the larger distance of the region in WM away from the fusion line, the smaller CTLZ and larger ETZ occurred. Compared with the fine and ellipsoidal precipitates in the as-welded CTLZ, a large number of chain-type clustered precipitates were detected in the CTLZ and ETZ interface after the aging treatment at 566 °C for 1 000 h. The element diffusion under elevated temperature in WM is regarded as the crucial factor for such anomalous microstructure evolution during the aging treatment.The full text can be downloaded at https://link.springer.com/article/10.1007/s40436-022-00396-z     

Microstructure and mechanical properties of aluminium/steel dissimilar weldments: effect of heat input

Lap joints of aluminium alloy A6061-T6 and galvanised steel DP800 were produced by an advanced gas metal arc welding process with AlSi3Mn filler. Four heat inputs designated as A (110?J?mm^?1), B (120?J?mm^?1), C (130?J?mm^?1) and D (140?J?mm^?1) were used during the process and the joints made were subjected to analysis of the microstructures, mechanical properties, residual stresses and corrosion behaviour. Microstructural analysis shows the formation and variation of Fe–Al intermetallic (IM) layer. It is also found that the joints made using the heat input of 120?J?mm^?1 exhibited highest tensile strength and better corrosion resistance. Electron microscopy and X-ray diffraction analysis revealed the presence of different IM phases with other strengthening precipitates.     

Influence of Aging treatment on the microstructure and mechanical properties of T92/Super 304H dissimilar metal welds

Influence of aging treatment on the microstructure and mechanical properties of T92/Super 304H dissimilar steel joints was investigated. The microstructure of T92/Super 304H dissimilar steel joints was characterized using optical microscopy, scanning electron microscopy and energy dispersive spectrometer. The results show that the tensile strength of dissimilar metal welds (DMWs) after 10,000 h aging treatment met the ASME T92 and Super 304H standards. Rupture positions were located in the T92 base metal because of the precipitates formed along the sub grain and prior grain boundaries. The tensile strength of DMWs initially increased with time up to 4000 h, then decreased between 4000 to 6000 h, and finally came to almost a constant value from 8000 to 10,000 h exposure. The decrease in the tensile strength resulted from the nucleation and growth of Laves phases at the sub-grains and prior austenitic grain boundaries. The low absorption of impact energy in the weld metal was related to the coarse grains and its grain orientation.     

Pulse current treatment effect on the strength of reinforcing steel and its weld joint under impact loading

We present results of static and impact tension tests of as-received reinforcing steel specimens, specimens with weld joints in their test portion, as well as specimens pretreated by high-density pulse current. As test results demonstrate, an increased strain rate enhances strength, and the pulse current treatment greatly influences the strength and plasticity of a defect-containing weld metal under static and impact tension. Translated from Problemy Prochnosti, No. 3, pp. 89–96, May–June, 2009.     

Effect of brazing temperature on tensile strength and microstructure for a stainless steel plate-fin structure

This paper presented a vacuum brazing technology for 304 stainless steel plate-fin structures with BNi2 filler metal. The effect of brazing temperature on tensile strength and microstructure has been investigated. The tensile strength is increased along with the increasing of brazing temperature. The microstructure is very complex and some Boride compounds are generated in the brazed joint. Full solid solution can be generated in the middle zone of joint when the brazing temperature is increased to 1100 °C. The brittle phases always exist in the fillet no matter how the brazing temperature changes, but the microstructure in fillet becomes more uniform and the tensile strength is increased with the brazing temperature increasing. In total, the brittle Boride compounds are decreased with the brazing temperature increase. Brazing with a filler metal thickness 105 μm and 25 min holding time, 1100 °C is the best suitable brazing temperature and a tensile strength of 82.1 MPa has been achieved for 304 stainless steel plate-fin structure.     

Microstructure and mechanical properties of the T23 steel after long-term ageing at elevated temperature

The paper presents the results of research on the microstructure and mechanical properties of T23 steel after long-term ageing up to 70 000 h at the temperature of 550 and 600 °C. It has been shown that the main mechanisms of degradation of the T23 steel microstructure were: recovery of the matrix, disintegration of the bainitic microstructure, growth of carbide diameter and precipitation of M6C carbides. These processes were more advanced in the steel aged at higher temperature. The changes in the microstructure resulted in a 10–15% decrease in mechanical properties (YS, TS) and hardness HV10, and a 30–40% decrease in the impact energy kV. A greater fall of impact strength occurred in the steel aged at the lower temperature. This was ascribed to the segregation of phosphorus to grain boundaries, which has a well-known adverse effect on ductility of low-alloy steels.     

High strength and ductility of 34CrNiMo6 steel produced by laser solid forming

Because of the excellent mechanical properties of 34CrNiMo6 steel, it is widely used in high-value components. Many conventional approaches to strengthening-steels typically involve the loss of useful ductility. In this study, 34CrNiMo6 Steel having high strength and ductility is produced by laser solid forming (LSF) with a quenching-tempering (QT) treatment. Tempering of bainite is mainly by solid phase transformation in the previous LSF layers during the LSF process. The stable microstructure of LSF consists of ferrite and fine carbides. The microstructure transfers to tempered sorbite after heat-treatment. The tensile properties of the LSF steel meet those of the wrought standard. The UTS and elongation of LSF sample at 858 MPa, 19.2%, respectively, are greater than those of the wrought. The QT treatment enhanced the ultimate tensile strength and yield strength of the LSF sample. The ultimate tensile strength, yield strength, reduction in area, and elongation of the LSF+QT sample at 980 MPa, 916 MPa, 58.9%, and 13.9%, respectively, are greater than those of the wrought standard. The yield strength of the LSF+QT sample is approximately 1.27 times that of the wrought. The LSF samples failed in a ductile fracture mode, while the LSF+QT samples showed mixed-mode failure. The defects have only a small effect on the tensile properties owing to the excellent ductility of the LSF sample.     

Prediction of debonding strength of tensile steel/CFRP joints using fracture mechanics and stress based criteria

In this paper, the debonding strength of axially loaded double shear lap specimens between steel plates and carbon fibre reinforced plastic plates is investigated from the analytical, numerical and experimental point of view. Two steel plates were joined together by two carbon fibre reinforced plastic (CFRP) plates and epoxy adhesive in order to realize double shear lap specimens of different length. Failure of the steel-adhesive interface was identified as the dominant failure mode and fracture mechanics and stress based approach are presented in order to estimate the relevant failure load. A good agreement between the analytical-numerical results and experimental data is achieved.     

Microstructure and Mechanical Properties of Pulse MIG Welded 6061/A356 Aluminum Alloy Dissimilar Butt Joints

The microstructure and mechanical properties of pulse metal inert-gas(MIG) welded dissimilar joints between 4 mm thick wrought 6061-T6 and cast A356-T6 aluminum alloy plates were investigated. The tensile strength of the joints reached 235 MPa, which is 83% of that of 6061 aluminum alloy, and then decreased with the increase of travel speed while keeping other welding parameters constant. The microstructure, composition and fractography of joints were examined by the optical microscopy(OM),scanning electron microscopy(SEM) and electron probe microanalysis(EPMA). Grain boundary liquation and segregation occurred in the partially melted zone(PMZ) on 6061 aluminum alloy side, and brittle Fe-rich phases were observed in partially melted zone on A356 aluminum alloy side. The minimum microhardness appeared in heat-affected zone(HAZ) near A356 aluminum alloy substrate. The samples during tensile test failed mainly in PMZ and HAZ on A356 aluminum alloy side through mixed fracture mode with quasi cleavage and dimples on fracture surface.     

An assessment of mechanical properties of P92 steel weld joint and simulated heat affected zones by ball indentation technique

Mechanical properties of P92 steel weld joint fabricated by shielded metal arc welding were evaluated using ball indentation (BI) technique. Microstructure of the P92 weld joint consisted of the weld metal, coarse grain region, fine grain region, intercritical region and base metal. The individual microstructural regions of the heat affected zones (HAZs) were separately prepared by heat treating the steel at particular temperatures. Ball indentation and uniaxial tensile tests were carried out across the weld joint and on the simulated HAZ microstructures at temperatures of 300 K (27 °C) and 623 K (350 °C). The tensile strengths gradually decreased from weld metal to the base metal with trough in the intercritical region (ICR) of the joint and simulated at 1173 K (900 °C) steel. The formation of coarser M₂₃C₆ precipitates and sub-grain formation with reduced dislocation density led to soften the ICR/simulated at 1173 K (900 °C) steel than the other regions of the joint. The variation of mechanical properties across the joint was comparable with variation of hardness and microstructural constituents across the joint.