首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 31 毫秒
1.
The fabrication process and thermal properties of 50–71 vol% SiCp/Al metal matrix composites (MMCs) for electronic packaging applications have been investigated. The preforms consisted with 50–71 vol% SiC particles were fabricated by the ball milling and pressing method. The SiC particles were mixed with SiO2 as an inorganic binder, and cationic starch as a organic binder in distilled water. The mixtures were consolidated in a mold by pressing and dried in two step process, followed by calcination at 1100 °C. The SiCp/Al composites were fabricated by the infiltration of Al melt into SiC preforms using squeeze casting process. The thermal conductivity ranged 120–177 W/mK and coefficient of thermal expansion ranged 6–10 × 10–6/K were obtained in 50–71 vol% SiCp/Al MMCs. The thermal conductivity of SiCp/Al composite decreased with increasing volume fraction of SiCp and with increasing the amount of inorganic binder. The coefficient of thermal expansion of SiCp/Al composite decreased with increasing volume fraction of SiCp, while thermal conductivity was insensitive to the amount of inorganic binder. The experimental values of the coefficient of thermal expansion and thermal conductivity were in good agreement with the calculated coefficient of thermal expansion based on Turner's model and the calculated thermal conductivity based on Maxwell's model.  相似文献   

2.
《Materials Letters》2002,52(4-5):334-341
Al–12 wt.% Si alloy matrix composites reinforced with high volume fraction of Sip were fabricated by squeeze infiltration. The effects of the compacting pressure on the volume fraction of Sip in preforms, and the influences of Sip size and volume fraction on the properties of Al/Sip composites were examined through this study. Si particles were compacted at different pressure of 40–130 MPa followed by sintered at 1000 °C for 7 h to obtain preforms containing 60–70 volume fraction (vol.%) of Sip. The sintered preforms were then infiltrated with Al–12 wt.% Si alloy at 750 °C under a 75 MPa squeeze infiltration pressure. It was found that lower coefficient of thermal expansion (CTE) and smaller density may be obtained with higher Sip volume fraction, yet increasing Sip volume fraction leads to higher amount of porosities in the composites and thus lowers the thermal conductivity (TC) and flexural strength. Besides, with the same Sip volume fraction, coarse Si particles result in higher CTE and TC, while finer Si particles may lower CTE and enhance the flexural strength of the composites effectively. From the results obtained in this study, it is expected that the high volume fraction Sip reinforced Al/Sip composites posses good potential in electronic packaging applications.  相似文献   

3.
Aluminium-matrix composites were fabricated by liquid metal infiltration of porous particulate reinforcement preforms, using AlN, SiC and Al2O3 as the particles. The quality of the composites depended on the preform fabrication technology. In this work, this technology was developed for high-volume fraction (up to 75%) particulate preforms, which are more sensitive to the preform fabrication process than lower volume fraction whisker/fibre preforms as their porosity and pore size are much lower. The technology developed used an acid phosphate binder (with P/Al molar ratio=23) in the amount of 0.1 wt% of the preform, in contrast to the much larger binder amount used for whisker preforms. The preforms were made by filtration of a slurry consisting of the reinforcement particles, the binder and carrier (preferably acetone), and subsequent baking (preferably at 200 °C) for the purpose of drying. Baking in air at 500 °C instead of 200 °C caused the AlN preforms to oxidize, thereby decreasing the thermal conductivity of the resulting Al/AlN composites. The reinforcement-binder reactivity was larger for AlN than SiC, but this reactivity did not affect the composite properties due to the small binder amount used. The Al/AlN composites were superior to the Al/SiC composites in the thermal conductivity and tensile ductility. The Al/Al2O3 composites were the poorest due to Al2O3 particle clustering.  相似文献   

4.
An optimum method for producing Al-SiCp metal matrix composites was developed by determining the optimum conditions for wetting SiC by aluminum and the optimum parameters for pressureless infiltration of SiCp preforms. The quantitative effect of magnesium and silicon additions to aluminum, free silicon on the SiC substrate, nitrogen gas in the atmosphere, and process temperature on the wetting characteristics of SiC by aluminum alloys was investigated using the sessile drop technique. The contribution of each of these parameters and their interactions, in terms of a relative power, to the contact angle, surface tension, and driving force for wetting were determined. In addition, an optimized process for enhanced wetting was suggested and validated. The optimum conditions for wetting SiC by aluminum that were arrived at were used to infiltrate SiCp preforms and the mechanical properties of the resulting metal matrix composites were measured. The effect of SiC particle size, infiltration time, preform height, vol.% SiC in the preform, and Si coating on the SiC particles on the pressureless infiltration of SiCp compacts with aluminum was investigated and quantified. The contribution of each of these parameters and their interactions to the retained porosity in the composite, the modulus of elasticity, and the modulus of rupture were determined. Under optimum infiltration conditions, metal matrix composites with less than 3% porosity, over 200 GPa modulus of elasticity, and about 300 MPa modulus of rupture were routinely produced.  相似文献   

5.
Statistical analysis for strength and spatial distribution of reinforcement in die-cast SiCp/Al alloy composites was performed in order to predict the reliability of composites. Microstructural analysis was also done to determine the critical features of the composites. Die-casting was carried out using the preheated die at the casting temperature range of 620–750°C. It was found that the SiC pacticulates were homogeneously dispersed in die-cast Al matrix alloy, resulting from the refinement of dendritic cell size due to rapid cooling rate. The tensile strength of die-cast SiCp/Al alloy composites was higher than that of die-cast Al matrix alloy. Also, the tensile strength was slightly increased with increasing SiC particulate volume fraction at the casting temperature range of 650–700°C. It was concluded that the die-cast temperatures of 750 and 700°C are optimum condition for the distribution of SiC particulates in consequence of good fluidity of melt for 10 and 20 vol.% SiCp/Al alloy composites, respectively. However, the strength scattering of composites was increased with increasing SiC particulate volume fraction. For the statistical evaluation of strength, the maximum Weibull modulus of die-cast SiCp/Al alloy composites, which was obtained at the cast temperature of 700°C, was 29.6 in Al matrix alloy, 22.2 in 10 vol.% SiCp and 14.2 in 20 vol.% SiCp, respectively.  相似文献   

6.
The thermal conductivity of SiCp/Al composites with high volume fractions of 46 to 68% has been investigated. The composites were fabricated by pressureless infiltrating liquid aluminum into SiC preforms with monomodal and bimodal size distributions. The density measurement indicates that a small amount of pores is presented for the composites approaching their maximum volume fractions. An analytical model with an explicit expression is proposed for describing the thermal conductive behavior of the composites with multimodal-reinforced mixtures in terms of an effective medium approach taking into account the porosity effect. Predictions of the developed effective medium expression reveal good correspondence with the experimental results, and explore how each of the considered factors (i.e., particle size ratio, volume fraction ratio, and porosity) can have a significant effect on the thermal conductivity of the composites with bimodal mixtures.  相似文献   

7.
压铸法制造SiCw/Al复合材料的渗透过程分析   总被引:1,自引:1,他引:0       下载免费PDF全文
本文深入分析了用压铸法制造SiCw/Al复合材料过程中液态铝渗入SiC晶须预制块中的渗透过程。通过理论计算得到液态铝渗入晶须预制块的临界渗透压不超过2MPa。对不同晶须含量的预制块所进行的模拟渗透过程的压缩试验结果表明,随外力的增加,预制块被压缩的程度增大,从而使预制块的晶须相对含量增大。通过对渗透过程的分析,认为液态铝渗透晶须预制块需要一定时间,因此当外力以较大的速度达到最大值时,液态铝不能完全渗入预制块中,这时预制块将被压缩,导致所得复合材料晶须相对含量提高。研究结果表明,复合材料晶须体积分数主要取决于预制块晶须体积分数和复合压力。   相似文献   

8.
37.2 vol.% SiCP/SiC and 25.0 vol.% SiCW/SiC composites were prepared by chemical vapor infiltration (CVI) process through depositing SiC matrix in the porous particulate and whisker preforms, respectively. The particulate (or whisker) preforms has two types of pores; one is small pores of several micrometers at inter-particulates (or whiskers) and the other one is large pores of hundreds micrometers at inter-agglomerates. The microstructure and mechanical properties of 37.2 vol.% SiCP/SiC and 25.0 vol.% SiCW/SiC composites were studied. 37.2 vol.% SiCP/SiC (or 25.0 vol.% SiCW/SiC) consisted of the particulate (or whisker) reinforced SiC agglomerates, SiC matrix phase located inter-agglomerates and two types of pores located inter-particulates (or whiskers) and inter-agglomerates. The density, fracture toughness evaluated by SENB method, and flexural strength of 37.2 vol.% SiCP/SiC and 25.0 vol.% SiCW/SiC composites were 2.94 and 2.88 g/cm3, 6.18 and 8.34 MPa m1/2, and 373 and 425 MPa, respectively. The main toughening mechanism was crack deflection and bridging.  相似文献   

9.
A new type of hybrid SiC foam–SiC particles–Al composites (VSiC = 53, 56.2 and 59.9%) to be used as an electronic packaging substrate material were fabricated by squeeze casting technique, and their thermal expansion behavior was evaluated. The coefficients of thermal expansion (CTEs) of the hybrid composites in the range of 20–100 °C were found to be between 6.6 and 7.7 ppm/°C. The measured CTEs are much lower than those of SiC particle-reinforced aluminum (SiCp–Al) composites with the same content of SiC because of the characteristic interpenetrating structure of the hybrid composites. A material of such a low CTE is ideal for electronic packaging because of the low thermal mismatch (and therefore, low thermal stresses) between the electronic component and the substrate. To achieve similar CTEs in SiCp–Al composites, the volume fraction of SiC would be much higher than that in the hybrid composites.  相似文献   

10.
Abstract

A336 Al matrix composites containing different volume fraction and mean mass particle size of SiC particles as the reinforcing phase were synthesised by evaporative pattern casting (EPC) route. The process consisted of fabricating of EPS/SiCp composite pattern followed by EPC of A336 Al alloy. The EPS/SiCp pattern was made by blending SiC particles with expandable polystyrene (EPS) beads and placing them in expanding mould heating with steam until EPS beads expand completely. Uniform distributed SiC particles around the EPS beads and locally movement of them during pouring and degradation leads to homogenous distribution of particles in final Al/SiCp composite. Higher modulus, strength and hardness were observed in the composites than the unreinforced Al alloy part. The fracture surfaces of the composite samples exhibited dimple surfaces and fracture in SiC particles.  相似文献   

11.
《Materials Letters》2004,58(27-28):3545-3550
Pure aluminum matrix composite reinforced with a high volume fraction of silicon particles (Al/Sip) was fabricated by gas-pressured infiltration. The results of four point flexural strength tests show that Al/Sip has low flexural strength. The analysis of the fractograph reveals the fracture mechanism of Al/Sip. The fracture of Al/Sip is primarily dominated by the fracture of brittle silicon particles and the subsequent link up of damage through the matrix. The pre-existent microcracks in silicon particles that were made during the process of compacting will also lower the flexural strength of Al/Sip composite. The hybrid particle reinforced pure aluminum matrix composite (Al/Sip+SiCp) was fabricated in the same way. Results show the flexural strength can be improved by 11.3% compared with Al/Sip when 6 vol.% silicon particles are replaced by silicon carbide particles with the same volume fraction and size. The reason is that SiCp with higher fracture stress and higher elastic modulus can prevent the rapid expansion of cracks through the composite and lower the stress in silicon particles.  相似文献   

12.
One of the great challenges of producing cast metal matrix composites is the agglomeration tendency of the reinforcements. This would normally result in poor distribution of the particles, high porosity content, and low mechanical properties. In the present work, a new method for uniform distribution of very fine SiC particles with average size of less than 3 μm was employed. The key idea was to allow for gradual in situ release of properly wetted SiC particles in the liquid metal. For this purpose, SiC particles were injected into the melt in three different forms, i.e., untreated SiCp, milled particulate Al–SiCp composite powder, and milled particulate Al–SiCp–Mg composite powder. The resultant composite slurries were then cast from either fully liquid (stir casting) or semisolid (compocasting) state. Consequently, the effects of the casting method and the type of the injected powder on the microstructural characteristics as well as the mechanical properties of the cast composites were investigated. The results showed that the distribution of SiC particles in the matrix and the porosity content of the composites were greatly improved by injecting milled composite powders instead of untreated-SiC particles into the melt. Casting from semisolid state instead of fully liquid state had similar effects. The average size of SiC particles incorporated into the matrix was also significantly reduced from about 8 to 3 μm by injecting milled composite powders. The ultimate tensile strength, yield strength and elongation of Al356/5 vol.%SiCp composite manufactured by compocasting of the (Al–SiCp–Mg)cp injected melt were increased by 90%, 103% and 135%, respectively, compared to those of the composite manufactured by stir casting of the untreated-SiCp injected melt.  相似文献   

13.
《Composites Part A》2003,34(11):1023-1027
With mixing different sized SiC particles, high reinforcement content SiCp/Al composites (Vp=50, 60 and 70%) for electronic packaging applications were fabricated by squeeze casting technology. The composites were free of porosity and SiC particles distributed uniformly in the composite. The mean linear coefficients of thermal expansion (20–100 °C) of SiCp/Al composites ranged from 8.3 to 10.8×10−6/°C and decreased with an increase in volume fraction of SiC content. The experimental coefficients of thermal expansion agreed well with predicted values based on Kerner's model. The Brinell hardness increased from 188.6 to 258.0, and the modulus increased from 148 to 204 GPa for the corresponding composites. The bending strengths were larger than 370 MPa, but no obvious trend between bending strength and SiC content was observed.  相似文献   

14.
This paper presents the experimental results on the machinability of silicon and silicon carbide particles (SiCp) reinforced aluminium matrix composites (Al/Sip + SiCp) during milling process using a carbide tool. The total volume fraction of the reinforcements is 65 vol%. The milling forces, flank wear of the tool and the machined surface quality of composites with different volume fraction of SiCp were measured during experiments. The machined surfaces of composites were examined through SEM. The results showed that the flexural strength and Vickers hardness are improved when certain volume fraction of silicon particles are replaced by silicon carbide particles with the same volume fraction and particle size and the effect of SiCp on machinability is optimal when 9 vol% silicon particles in Al/Sip was replaced by silicon carbide particles with the same volume fraction and the same particle size. Cracks and pits were found on the machined surfaces of composites due to the intrinsic brittleness of silicon particles.  相似文献   

15.
《Composites Science and Technology》2007,67(11-12):2377-2383
Polymethylsiloxane (PMS) was used as a binder to make self-supporting SiC preforms for pressurized aluminum melt infiltration. The SiC particles were coated with preceramic polymer by spray drying; this ensured a fine and homogeneous distribution coupled with a high yield of the binder. The conditioned SiC powder mixtures were processed into preforms by warm pressing, curing and pyrolysis. A polymer content of 1.25 wt.% conferred sufficient stability to the preforms to enable composite processing. Using this procedure, SiC preforms with various SiC particle size distributions were prepared. The resulting Al/SiC composites with SiC contents of about 60 vol.% obtained by squeeze casting infiltration exhibit a 4-point bending strength of ∼500 MPa and Young’s moduli of ∼200 GPa. These values are comparable to those of compositionally identical, but binder-free composites. It is thus shown that the PMS-derived binder confers the desired strength to the SiC preforms without impairing the mechanical properties of the resulting Al/SiC composites.  相似文献   

16.
Squeeze-cast metal-matrix composite ingots have been manufactured by recasting A356/10% SiCp and by melt infiltrating A357/Al2O3f. The resulting microstructures have been examined by optical and transmission electron microscopy. The primary aluminium in squeeze-cast A356/10% SiCp exhibits a dendritic structure with eutectic silicon particles and SiC particulate distributed throughout the interdendritic regions. Unlike squeeze-cast monolithic A357, the primary aluminium dendrite arm spacing and eutectic-silicon particle size in squeeze-cast A356/10% SiCp are not strongly affected by an increased cooling rate at high applied pressure. With low die and preform temperature, a high applied pressure is essential to obtain complete melt infiltration in A357/Al2O3f. During melt infiltration, the ceramic preform acts as a filter, preferentially allowing silicon rich liquid to pass through.  相似文献   

17.
运用放电等离子烧结(SPS)技术制备出体积分数达60%,致密度达99%的SiCp/Al复合材料.从烧结工艺的控制及电场的影响两方面对SPS烧结SiC,/Al复合材料的机理进行了研究,认为SPS烧结SiCp/Al复合材料的致密化过程主要依靠烧结温度、压力及升温速率的合理搭配,使Al熔融粘结SiC颗粒,而又不溢出模具;烧结过程中未发现明显的放电现象,可能由于电场太弱不足以引发放电.  相似文献   

18.
Two 6061 Al alloy matrix composites reinforced with rods that are themselves composites of the same Al alloy reinforced with a high volume fraction of SiC particles were studied. After vacuum pressure infiltration, one was hot extruded at a ratio of 10 : 1 and the other at a ratio of 60 : 1. The fracture characteristics of the two SiCp-6061Al/6061Al composites were examined in detail. It was found that increasing the hot extrusion ratio of this kind of composite can improve the bonding between the SiCp-6061Al bars and the 6061Al matrix. The strengths of the SiCp-6061Al bars and the 6061Al matrix were considered to increase with increasing extrusion ratio. Thus, the SiCp-6061Al/6061Al composite extruded at a ratio of 60 : 1 shows fracture characteristics which are different from the composite extruded at a ratio of 10 : 1. The former has a higher fracture toughness, and its crack opening displacement versus load curve indicates a higher elastic modulus and maximum load. After application of the maximum external load, there is a slow decrease with increasing crack opening displacement in the case of the 60 : 1 extruded composite, but the load can be maintained for wide crack opening displacement in the case of the 10 : 1 extruded composite.  相似文献   

19.
A cost effective method was introduced to fabricate pure aluminum matrix composites reinforced with 20% volume fraction of 3.5 μm SiC particles by squeeze casting followed by hot extrusion. In order to lower volume fraction of the composites, a mixed preform containing pure aluminum powder and the SiC particles was used. The suitable processing parameters for the infiltration of pure aluminum melt into the mixed preform are: melt temperature 800℃, preform temperature 500℃, infiltration pressure 5 MPa, and solidification pressure 50 MPa. Microstructure and properties of the composites in both as-cast and hot extruded states were investigated. The results indicate that hot extrusion can obviously improve the mechanical properties of the composite.  相似文献   

20.
Abstract

A spray formed aluminium alloy/SiCp composite, obtained by an alternative production route, was produced by mixing suitable amounts of A357.0 alloy and SiCp particles in the melting crucible of a laboratory scale gas atomiser, under a protective atmosphere. A mean volume fraction of reinforcing particles close to 15 vol.-% was achieved by properly choosing the melt superheat temperature and stirring speed. Microstructural characterisation of both the precomposite powders and of the spray deposited block was carried out by microscopy examination and X-ray diffraction. The variations of the volume fraction of reinforcement within the formed composite block were determined as a function of position and correlated to the corresponding local mechanical properties. The mechanical properties of the spray formed composite material are compared with those of the unreinforced alloy, spray formed in the same atomiser.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号