Technique for continuous tuning of optical fiber lasers

For the first time to the authors' knowledge, we have demonstrated how thermally controlled overcoupled fused fiber couplers and fiber loop mirrors based on these couplers can be used as broadband tuning elements in a fiber laser cavity. No bulk optical elements play any role in this technique. Temperature tuning the coupler results in a shift in the coupling ratio or in the effective output coupler transmission. For a fixed pump source, and for a given laser cavity, this shift causes the lasing wavelength to shift. We have continuously tuned an Er silica fiber laser in this manner over the range of 1527-1570 nm in a ring configuration, and, using a fiber loop mirror with these couplers in a linear Tm silica fiber laser cavity, we have achieved more than 50-nm broadband tuning over the range of 1850-1910 nm. The tuning range and the sensitivity to temperature depend on the degree of overcoupling of the loop mirror coupler.     

Hybrid Wavelength-Time-Domain Interrogation System for Multiplexed Fiber Bragg Sensors Using a Strain-Tuned Erbium-Doped Fiber Laser

A system for the interrogation of fiber Bragg grating (FBG) sensors using a strain-tuned EDF laser with linear cavity is described. An optical switch is spliced to one end of the laser cavity and connects one of two high-strength draw-tower fiber Bragg gratings (DTGs). The gratings are simultaneously tuned by a stretching device and act as the end reflector of the laser cavity. By applying a ramp signal to the actuator synchronized to the optical switch, the laser signal sweeps over two different wavelength intervals, depending on the connected DTG. This approach represents a hybrid wavelength-time-domain interrogation for multiplexed sensors and doubles the number of sensors that may be addressed when compared with single DTG scanning. In addition, the use of the DTG allows a fivefold increase in the strain tuned wavelength interval over standard fiber Bragg gratings. An example application is demonstrated where temperature inside an electrical motor is measured during operation.     

Switchable dual-wavelength single-longitudinal-mode erbium-doped fiber laser using an inverse-Gaussian apodized fiber Bragg grating filter and a low-gain semiconductor optical amplifier

We present a stable and switchable dual-wavelength erbium-doped fiber laser. In the ring cavity, an inverse-Gaussian apodized fiber Bragg grating serves as an ultranarrow dual-wavelength passband filter, a semiconductor optical amplifier biased in the low-gain regime reduces the gain competition of the two wavelengths, and a feedback fiber loop acts as a mode filter to guarantee a stable single-longitudinal-mode operation. Two lasing lines with a wavelength separation of approximately 0.1 nm are obtained experimentally. A microwave signal at 12.51 GHz is demonstrated by beating the dual wavelengths at a photodetector.     

Fiber-Bragg-grating force sensor based on a wavelength-switching actively mode-locked erbium-doped fiber laser

A fiber-Bragg-grating (FBG) transverse-force sensor based on a wavelength-switching actively mode-locked erbium-doped fiber laser is proposed, in which a FBG is used as both the sensing element and the wavelength-selection element of the laser. When a force is applied to the FBG, the induced birefringence in the FBG causes the laser to emit pulses at two close wavelengths, whose separation is proportional to the applied force. To suppress the interference between the two wavelengths, the laser is made to emit at the two wavelengths alternately by use of a polarization-switching technique. The wavelength separation is converted into a time difference by transmission of the laser pulses through a dispersive single-mode fiber, so the wavelength measurement is replaced by the less-expensive time measurement. The output of the sensor is insensitive to temperature and axial strain changes along the FBG. To interrogate similar FBG sensing elements connected in series it is necessary only to change the modulating frequency of an electro-optic modulator to select the corresponding laser cavity. The practicability of this approach was demonstrated experimentally with two multiplexed sensing elements.     

Switchable and tunable multiple-channel erbium-doped fiber laser using graphene-polymer nanocomposite and asymmetric two-stage fiber Sagnac loop filter

A high-performance multiple-channel erbium-doped fiber laser (EDFL) is proposed and experimentally demonstrated, using graphene-polymer nanocomposite as a multiwavelength equalizer and an asymmetric two-stage polarization-maintaining fiber (PMF) Sagnac loop as a flexible comb filter. At first, the filtering characteristics of the PMF Sagnac loop filter (SLF) are investigated. Both theoretical and experimental results show that it can provide a flexibly switchable and tunable comblike filtering. Then, the two-stage PMF SLF is inserted into a graphene-assisted EDFL cavity for generating multiwavelength oscillation. The extreme-high third-order optical nonlinearity of graphene is exploited to suppress the mode competition of the EDFL, and a stable multiple-channel lasing is observed. By carefully adjusting the polarization controllers in the two-stage PMF SLF, not only can the lasing-line number per channel be switchable between single and multiple wavelengths, but also the wavelength spacing in the triple-wavelength condition can be tunable. In the case of triple wavelengths per channel, up to 12 wavelengths with four channels stable oscillations can be achieved. The multiple-channel EDFL can keep a high extinction ratio of >40 dB and a narrow linewidth of <0.01 nm.     

Tunable graphene Q-switched erbium-doped fiber laser with suppressed self-mode locking effect

Self-mode locking effect in a wideband tunable graphene-based passively Q-switched erbium-doped fiber laser has been observed experimentally. Q-switching is achieved by using graphene as a saturable absorber, while a tunable bandpass filter with a narrow bandwidth is used to obtain wideband tunability. We propose to suppress the modulation on each pulse from self-mode locking by introducing three subring resonators constructed with three 3 dB couplers into the laser ring cavity. Moreover, the laser output characteristics with respect to pump power are studied in detail. A stable Q-switched erbium-doped fiber laser with a tunable range from 1522 nm to 1568 nm is demonstrated experimentally.     

Characterization of a multiwavelength Brillouin-erbium fiber laser based on a linear cavity configuration

We experimentally demonstrate a simple method for generating a multiwavelength Brillouin comb by utilizing a linear cavity of hybrid Brillouin-erbium fiber lasers (BEFLs). The optimization of Brillouin pump wavelength, power, and erbium gain played a significant role in determining the maximum number of Brillouin Stokes signals generated. Simultaneous and stable multiple-wavelength laser output of 22 lines with 10.88-GHz channel spacing has been obtained with good flatness. Various parameters such as 980-nm pump power, Brillouin pump wavelength, and Brillouin pump power that affect the performance of a multiwavelength BEFL system have been investigated. An analysis of the tuning range of the system is presented.     

Mode-locked ytterbium fiber lasers

A compact fiber laser is demonstrated with use of a Gires-Tournois compensator and a short length (2-4 cm-long) of highly doped ytterbium (Yb) fiber providing net anomalous group-velocity dispersion. With use of a novel semiconductor saturable absorber mirror based on GaInNAs structure, self-started 1.5-ps-pulse mode-locked operation was obtained at 1023 nm with a repetition rate of 95 MHz. A mode-locked Yb-doped fiber laser was developed without the use of any dispersion compensation technique. Overall group-velocity dispersion was minimized by using a short length of highly doped Yb fiber in a compact amplifying loop cavity. Self-started mode-locked operation was obtained in 980-1030-nm wavelength range with a fundamental repetition rate of 140 MHz.     

SOA-based multi-wavelength source

A simple fiber laser configuration based on a semiconductor optical amplifier (SOA) is proposed for obtaining multi-wavelength oscillation at room temperature, in which a Sagnac loop mirror is used as the wavelength selective component. The SOA has a flat gain of approximately 23dB within a bandwidth of 12 nm at a small input signal power. The loop mirror was constructed using a 3dB coupler and polarization maintaining fiber (PMF). The output spectrum of the proposed laser can be adjusted by controlling the bias current of the SOA and is quite stable at room temperature. At a bias current of 150 mA, six lines are obtained with at least ?40 dBm output power and 25dB signal-to-noise ratio (SNR). The channel spacing and number of lines is determined by the length of polarization maintaining fiber (PMF) used in the loop mirror. The channel spacing of the proposed laser is 1.49 nm with a PMF 3 m. The multi-wavelength comb output can also be tuned by adjusting the operating temperature of the SOA. The multi-wavelength laser has the advantage of a simple configuration, stability at room temperature, a broad wavelength band, and no need for optical pump lasers.     

Bismuth activated alumosilicate optical fibers fabricated by surface-plasma chemical vapor deposition technology

Plasma chemical technology is experimentally applied to the fabrication of a Bi-activated alumosilicate-core pure-silica-cladding fiber preform. To the best of our knowledge, this is the first time this technology has been applied in this way. We measure gain efficiency at pumping by a 1058 nm wavelength Yb fiber laser in a piece of a newly obtained fiber 20 m in length within 100-1200 nm wavelengths band. The gain efficiency reaches as high as 0.2 dB/mW. Bi-activated alumosilicate-core pure-silica-cladding fiber that is not more than 12 m in length serves a basis for a 1 W output power fiber laser emitting at the wavelength of 1160 nm with 8% slope efficiency. We also measure the photoluminescence spectrum and kinetics of Bi centers responsible for laser emission under the excitation of 193 nm wavelength ArF laser pulses.     

Investigation of the Static and Dynamic Characteristics for a Wafer-Fused C-band VCSEL in the Mode of the Optical-Electric Converter

The results of an experimental study for a long wavelength vertical cavity surface-emitting laser of a wafer-fused construction as an effective resonant cavity enhanced photodetector of analog optical signals are described. The device is of interest for a number of promising microwave photonics applications and for creation of a low-cost photoreceiver in a high-speed fiber optics telecommunication system with dense wavelength division multiplexing. The schematic of the testbed, the original technique allowing to calculate the passband of the built-in optical cavity, and the results of measuring dark current, current responsivity, amplitude- and phase-frequency characteristics during the process of photo-detection are demonstrated.     

Sensitive absorption spectroscopy by use of an asymmetric multiple-quantum-well diode laser in an external cavity

We have developed a broadly tunable diode laser system by employing custom-designed asymmetric multiple-quantum-well (AMQW) InGaAsP lasers in an external cavity configuration. Feedback is provided by a diffractive optical element with high coupling efficiency and wavelength selectivity, allowing for single-mode tuning of the output wavelength by varying the external cavity length. This tunable laser system was used experimentally to perform absorption spectroscopy on weak CO(2) lines over a broad wavelength region in the near infrared. An experimental tuning range of 80 nm has been observed for a laser cavity length of 600 mum, which is double the tuning range found with conventional, uncoated quantum-well lasers. We achieved a detection sensitivity of 5 x 10(-6) at 95% confidence over the wavelength range of 1.54-1.62 mum by employing a second-harmonic detection technique. The theoretical predictions of a broad gain profile from an ambipolar rate equation model are found to correspond to the experimentally observed increased tunability of the uncoated AMQW lasers.     

Distributed measurement of static strain in an optical fiber with multiple bragg gratings at nominally equal wavelengths

The Fourier transform relationship between the reflected light froma Bragg grating and the complex spatial modulation of the Bragg grating is used to produce a distributed strain sensing system. A tunable external cavity diode laser along with a reference reflector in anoptical fiber are used to produce a measurement of the phase and amplitude of the reflected light from the modulated Bragg grating as a function of wavelength. The system is demonstrated with 22 Bragg gratings in a single fiber on a cantilever beam and compared with foil strain gauge readings.     

Extending the continuous tuning range of an external-cavity diode laser

The continuous tuning range of an external-cavity diode laser can be extended by making small corrections to the external-cavity length through an electronic feedback loop so that the cavity resonance condition is maintained as the laser wavelength is tuned. By maintaining the cavity resonance condition as the laser is tuned, the mode hops that typically limit the continuous tuning range of the external-cavity diode laser are eliminated. We present the design of a simple external-cavity diode laser based on the Littman-Metcalf external-cavity configuration that has a measured continuous tuning range of 1 GHz without an electronic feedback loop. To include the electronic feedback loop, a small sinusoidal signal is added to the drive current of the laser diode creating a small oscillation of the laser power. By comparing the phase of the modulated optical power with the phase of the sinusoidal drive signal using a lock-in amplifier, an error signal is created and used in an electronic feedback loop to control the external-cavity length. With electronic feedback, we find that the continuous tuning range can be extended to over 65 GHz. This occurs because the electronic feedback maintains the cavity resonance condition as the laser is tuned. An experimental demonstration of this extended tuning range is presented in which the external-cavity diode laser is tuned through an absorption feature of diatomic oxygen near 760 nm.     

All-optical analog-to-digital conversion scheme based on Sagnac loop and balanced receivers

An all-optical analog-to-digital conversion scheme based on a Sagnac loop and balanced receivers is proposed and experimentally demonstrated. Adjustable phase shift about the transfer function of the Sagnac loop is obtained by using the multiwavelength optical pulses to realize the phase-shift optical quantization. Benefit from the complementary outputs at the transmitted and reflected ports of the Sagnac loop and balanced receiver can be used to obtain the quantized output binary signal for the encoding operation. A proof-of-concept experiment is implemented using a wavelength tunable continuous-wave laser diode. Using 16 different wavelengths, the 16 quantization levels are demonstrated and an effective number of bits (ENOB) of 4?bits is obtained.     

High Efficiency Pulse Compression by Raman Induced Cavity Dumping

Raman induced cavity dumping has been demonstrated theoretically and experimentally as an efficient technique of pulse compression. Through intracavity stimulated Raman scattering the electromagnetic energy at a primary frequency is down-converted and extracted from a storage cavity containing the Raman medium. Several experimental set-ups have been tested, concerning oscillators and amplifiers, using different pumping techniques. Results differ slightly according to the technique used, but pulse shortenings exceeding 10 and quantum efficiencies larger than 80 per cent were obtained. This method developed in the case of a ruby laser could also be used with large power lasers of any wavelength from the ultraviolet to the far infrared.     

Tunable multiwavelength fiber laser based on a double Sagnac HiBi fiber loop

A tunable multiwavelength fiber laser based on double Sagnac loops is proposed and demonstrated. Comb filter characteristics of single and double Sagnac loops are analyzed by Jones matrix. Simulated results show that there are better tunability and controllability with double loops than with a single loop, and this also has been confirmed by experimental results. By adjusting the polarization controller and the length of the polarization maintaining fiber the wavelength range, wavelength spacing, and laser linewidth can be tuned. Experimental results indicate that the linewidth of the multiwavelength fiber laser was 0.0187 nm and the optical sidemode suppression ratio was 50 dB.     

Measuring optical fiber length by use of a short-pulse optical fiber ring laser in a self-injection seeding scheme

A method for measuring the length of an optical fiber by use of an optical fiber ring laser pulse source is proposed and demonstrated. The key element of the optical fiber ring laser is a gain-switched Fabry-Perot laser diode operated in a self-injection seeding scheme. This method is especially suitable for measuring a medium or long fiber, and a resolution of 0.1 m is experimentally achieved. The measurement is implemented by accurately determining the pulse frequency that can maximize the output power of the fiber ring laser. The measurement results depend only on the refractive index of the fiber corresponding to this single wavelength, instead of the group index of the fiber, which represents a great advantage over both optical time-domain reflectometry and optical low-coherence reflectometry methods.     

Switchable multiwavelength ytterbium-doped double-clad fiber laser based on a multimode fiber grating

A simple switchable multiwavelength double-clad fiber laser using a multimode fiber Bragg grating (MMFG) as a wavelength selective component is demonstrated. The MMFG is fabricated directly in the active double-clad fiber, resulting in low splicing loss and compact configuration. By properly adjusting the polarization controller in the cavity, the double-clad fiber laser can stably operate at different multiwavelength states at room temperature. At lower pump levels, the laser can be switched between single- and dual-wavelength operations, while at higher pump levels the laser can switch between dual- and triple-wavelength operations. The slope efficiency of the system is 41% with the maximum output power of 6.2 W.     

High-resolution interrogation technique for fiber optic extrinsic Fabry-Perot interferometric sensors by the peak-to-peak method

An improved peak-to-peak method is developed for interrogating the absolute cavity length of fiber optic extrinsic Fabry-Perot interferometric (EFPI) sensors with high resolution. A fiber Fabry-Perot tunable filter (FFP-TF) is used to scan the optical spectrum of an EFPI, and the problems caused by the nonlinear performance and poor repeatability of the FFP-TF are removed by using a wavelength calibration technique. A linear fitting is used to calculate the wavelength spacing between two adjacent apexes in the optical spectrum, and the cavity length can be retrieved using this wavelength spacing. The experimental results show that the measuring resolution is improved from 25 to 1 microm, and a linear output is also obtained.