SMC-DPC based active and reactive power control of grid-tied three phase inverter for PV systems

In this paper, sliding mode control (SMC) – direct power controller (DPC) based active and reactive power controller for three-phase grid-tied photovoltaic (PV) system is proposed. The proposed system consists of two main controllers: the DC/DC boost converter to track the possible maximum power from the PV panels and the grid-tied three-phase inverter. The Perturb and Observe (P&O) algorithm is used to transfer the maximum power from the PV panels. Control of the active and reactive powers is performed using the SMC-DPC strategy without any rotating coordinate transformations or phase angle tracking of the grid voltage. In addition, extra current control cycles are not used to simplify the system design and to increase transient performance. The fixed switching frequency is obtained by using space vector modulation (SVM). The proposed system provides very good results both in transient and steady states with the simple algorithms of P&O and SMC-DPC methods. Moreover, the results are evaluated by comparing the SMC-DPC method developed for MPPT and the traditional PI control method. The proposed controller method is achieved with TMS320F28335 DSP processor and the system is experimentally tested for 12 kW PV generation systems.     

A novel real-time simulation technique of photovoltaic generation systems using RTDS

For the performance test of photovoltaic (PV) generation systems, actual system apparatuses: a solar panel, converter system, and load facilities should be installed. It is also hardly possible to compare a maximum power point tracking (MPPT) control scheme with others under the same weather and load conditions in an actual PV generation system. One of the possible alternatives is to realize a transient simulation scheme for PV generation systems under real weather conditions of insolation and surface temperature of solar cell. The authors propose a novel real-time simulation method for PV generation systems under real weather conditions using a real-time digital simulator (RTDS). V--I curves of a real PV panel are tested using electric load device, and a hypothetical network of the tested PV panel is created on the RTDS by arranging electrical components from the customized component model libraries. The real weather conditions, insolation, and temperature of the PV panel, are interfaced through the analog input ports of the RTDS for real-time simulation. The outcomes of the simulation demonstrate the effectiveness of the proposed simulation technique, and also show that cost-effective verification of availability and stability of PV generation systems is possible using the built-in simulator.     

Implementation of photovoltaic water pumping system with MPPT controls

To increase the output efficiency of a photovoltaic (PV) system, it is important to apply an efficient maximum power point tracking (MPPT) technique. This paper describes the analysis, the design and the experimental implementation of the tracking methods for a stand-alone PV system, using two approaches. The first one is the constant voltage (CV) MPPT method based on the optimum voltage, which was deduced experimentally, and considered as a reference value to extract the optimum power. The second one is the increment conductance (Inc-Cond) MPPT method based on the calculation of the power derivative extracted by the installation. The output controller can adjust the duty ratio to the optimum value. This optimum duty ratio is the input of a DC/DC boost converter which feeds a set of Moto-pump via a DC/AC inverter. This paper presents the details of the two approaches implemented, based on the system performance characteristics. Contributions are made in several aspects of the system, including converter design, system simulation, controller programming, and experimental setup. The MPPT control algorithms implemented extract the maximum power point (MPP), with satisfactory performance and without steady-state oscillation. MATLAB/Simulink and dSpace DS1104 are used to conduct studies and implement algorithms. The two proposed methods have been validated by implementing the performance of the PV pumping systems installed on the roof of the research laboratory in INSAT Tunisia. Experimental results verify the feasibility and the improved functionality of the system.     

A control scheme with performance prediction for a PV fed water pumping system

This paper focuses on modeling and performance predetermination of a photovoltaic (PV) system with a boost converter fed permanent magnet direct current (PMDC) motor-centrifugal pump load, taking the converter losses into account. Sizing is done based on the maximum power generated by the PV array at the average irradiation. Hence optimum sizing of the PV array for the given irradiation at the geographical location of interest is obtained using the predetermined values. The analysis presented here involves systems employing maximum power point tracking (MPPT) as they are more efficient than directly coupled systems. However, the voltage and power of the motor might rise above rated values for irradiations greater than the average when employing MPPT, hence a control scheme has been proposed to protect the PMDC motor from being damaged during these conditions. This control scheme appropriately chooses the optimum operating point of the system, ensuring long-term sustained operation. The numerical simulation of the system is performed in Matlab/Simulink and is validated with experimental results obtained from a 180 V, 0.5 hp PMDC motor coupled to a centrifugal pump. The operation of the system with the proposed control scheme is verified by varying the irradiation levels and the relevant results are presented.     

A photovoltaic powered electrolysis converter system with maximum power point tracking control

One of the main problems for renewable and other innovative energy sources is the storage of energy for sustainability. This study focuses on two different scenarios to benefit from solar energy more efficiently. Photovoltaic (PV) energy is converted to the desired voltage level using a buck converter for generating hydrogen with electrolysis process. A maximum power point tracking (MPPT) algorithm is used to benefit from the photovoltaic sources more efficiently. The basic electrolysis load for hydrogen production needs low voltage and high current and controlled sensitively to supply these conditions. The photovoltaic powered buck converter for electrolysis load was simulated in MATLAB/Simulink software using a perturb and observe (P and O) MPPT algorithm and PI controller. The simulation results show that in normal, short circuit and open circuit working conditions the PV and load voltages are stabilized. The efficiency of the proposed system is reached more than 90% for high irradiance levels.     

A maximum power point tracking control strategy with variable weather parameters for photovoltaic systems with DC bus

In photovoltaic (PV) system, the most commonly used DC/DC converter is the basic buck or boost circuit to implement the maximum point power tracking (MPPT) due to their simple structure and low cost while there are some MPPT constraint conditions. By contrast, the conventional buck/boost DC/DC converter without MPPT constraint condition is seldom used because of its high cost or poor performance. To keep the advantages of these three DC/DC converters while overcoming their shortcomings, in this paper, the constraint conditions of capturing the maximum power point (MPP) of PV systems with direct-current (DC) bus are found out. Then, on the basis of this work, a MPPT control strategy with variable weather parameters is proposed. In this strategy, a new buck/boost DC/DC converter is proposed, which not only avoids the MPPT constraint conditions of basic buck or boost DC/DC converter but also overcomes the shortcomings of conventional buck/boost DC/DC converter. Finally, lots of simulated experiments verify the accuracy of MPPT constraint conditions, test the feasibility and availability of proposed MPPT control strategy, analyze the MPPT performance of proposed PV system and compare the output transient-state performance with conventional perturb and observe (P&O) method.     

A Novel Auto-Scaling MPPT Algorithm based on Perturb and Observe Method for Photovoltaic Modules under Partial Shading Conditions

Maximum Power Point Tracking (MPPT) controller is required in a solar photovoltaic (PV) system to deliver the maximum power to load from PV module. This paper proposes a novel stepped MPPT method to realize a simple MPPT controller, which can track the real maximum power point (RMPP) even under partial shading conditions. The proposed algorithm is started by scanning the characteristic curve of the PV modules to detect the global maximum power point and then the algorithm will be switched to the conventional P&O algorithm to track the true maximum power point. The obtained simulation results, using Power electronic simulation software (PSIM), are compared with those found using the P&O method to confirm the performance of our proposed MPPT method even under non-uniform solar irradiation.     

Maximum power tracking for photovoltaic power system: Development and experimental comparison of two algorithms

This work presents an experimental comparison of two algorithms developed in order to maximize the output power from a photovoltaic (PV) system for the same given set of conditions. The maximum power point tracking (MPPT) methods proposed in this study are two extended algorithms: Perturb and Observe and Incremental Conductance. The numerical modelling of the PV system shows the MPPT interest and then the extended MPPT algorithms are highlighted. In this paper, a PV system based on a boost converter as MPPT device is considered. A programmable DC electronic load is fed by two identical PV systems in which the MPPT control converter algorithms are different. This experimental platform operates under the same conditions such as changing solar radiation and cell temperature. The experimental results obtained with a dSPACE controller board show the MPPT energy efficiency of the proposed algorithms.     

A comprehensive simulator for assessing the reliability of a photovoltaic panel peak power tracking system

When designing a maximum power point tracking (MPPT) algorithm, it is often difficult to correctly predict, before field testing, the behavior of this MPPT under varying solar irradiation on photovoltaic (PV) panels. A solution to this problem is to design a maximum power point trackers simulator of a PV system used to test MPPT algorithms. This simulator must have the same role as the MPPT card of the PV panel and thus will fully emulate the response of a real MPPT card of the PV panel. Therefore, it is a good substitute to help to test the peak power trackers of the PV system in the laboratory. This paper describes a simple peak power trackers simulator of the PV system which has a short response time thus, can be used to test MPPT algorithms under very rapid variation condition. The obtained results and the theoretical operation confirm the reliability and the superior performance of the proposed model.     

Fractional order extremum seeking approach for maximum power point tracking of photovoltaic panels

Due to the high interest in renewable energy and diversity of research regarding photovoltaic (PV) array, a great research effort is focusing nowadays on solar power generation and its performance improvement under various weather conditions. In this paper, an integrated framework was proposed, which achieved both maximum power point tracking (MPPT) and minimum ripple signals. The proposed control scheme was based on extremum-seeking (ES) combined with fractional order systems (FOS). This auto-tuning strategy was developed to maximize the PV panel output power through the regulation of the voltage input to the DC/DC converter in order to lead the PV system steady-state to a stable oscillation behavior around the maximum power point (MPP). It is shown that fractional order operators can improve the plant dynamics with respect to time response and disturbance rejection. The effectiveness of the proposed controller scheme is illustrated with simulations using measured solar radiation data.     

Modeling and simulation of three phase multilevel inverter for grid connected photovoltaic systems

This paper presents a control for a three phase five-level neutral clamped inverter (NPC) for grid connected PV system. The maximum power point tracking (MPPT) is capable of extracting maximum power from the PV array connected to each DC link voltage level. The MPPT algorithm is solved by fuzzy logic controller. The fuzzy MPPT is integrated with the inverter so that a DC–DC converter is not needed and the output shows accurate and fast response. A digital PI current control algorithm is used to remain the current injected into the grid sinusoidal and to achieve high dynamic performance with low total harmonic distortion (THD). The validity of the system is verified through MATLAB/Simulink and the results are compared with three phase three-level grid connected NPC inverter in terms of THD.     

Modeling and control of photovoltaic and fuel cell based alternative power systems

Photovoltaic (PV) systems and fuel cells (FCs) represent interesting solutions as being alternative power sources with high performance and low emission. This work presents a modeling and control study of two power generators; photovoltaic array and fuel cell based systems. An MPPT approach to optimize the PV system performances is proposed. The PV system consists of a PV array connected to a DC-DC buck converter and a resistive load. A maximum power point tracker controller is required to extract the maximum generated power. Based on Incremental Conductance (INC) principle, the idea of the proposed control is to use a Fuzzy Logic Controller (FLC) that allows the choice of the duty cycle step size which is used to be fixed in conventional MPPT algorithms. The variable step is computed according to the value of the PV power-voltage characteristic slope. The second working system comprises a controlled DC-DC converter fed by a proton exchange membrane fuel cell (PEMFC) and supplies a DC bus. The mathematical model of the PEMFC system is given. The converter duty cycle is adjusted in order to regulate the DC bus voltage. Obtained simulation results validate the control algorithms for both of studied power systems.     

Implementation of photovoltaic array MPPT through fixed step predictive control technique

This paper proposes the implementation of Photovoltaic (PV) array Maximum Power Point Tracker (MPPT) through Fixed Step-Model Predictive Controller (FS MPC). The proposed controller scheme is based on the modified INcremental Conductance (INC) algorithm combined with the two-step horizon FS MPC. The current based INC algorithm is subject to major modifications in order to be capable of real time interaction between the MPPT and the controller obtaining sufficient information in one sampling time. The developed technique has been incorporated into a model for the overall simulation of the performance of a PV array for solar energy exploitation and is compared to the conventional approach under solar radiation variation improving PV system utilization efficiency and enabling to optimize system performance. This study also illustrates the effectiveness of the proposed controller scheme under various sky conditions with a simulation model employing real solar radiation data.     

An on-line MPPT algorithm for rapidly changing illuminations of solar arrays

Maximum power point tracking (MPPT) is usually used for a solar power system. Many maximum power tracking techniques have been considered in the past. The microprocessors with appropriate MPPT algorithms are favored because of their flexibility and compatibility with different solar arrays. Although the efficiency of MPPT algorithms is usually high, it drops noticeably in case of rapidly changing illumination conditions. The authors have proposed an improved MPPT algorithm based on the fact that the maximum power point (MPP) of solar arrays can be tracked accurately. The principle of energy conservation is used to develop the large- and small-signal model and transfer function for the solar power system. The work was carried out by both simulation and experiment on a current converter, by the digital signal processor (DSP) control, in MPPT mode under different illuminations. The results show that the proposed MPPT algorithm has successfully tracked the MPP in rapidly changing illumination conditions.     

Maximum power point tracking of a proton exchange membrane fuel cell system using PSO-PID controller

Fuel cells output power depends on the operating conditions, including cell temperature, oxygen partial pressure, hydrogen partial pressure, and membrane water content. In each particular condition, there is only one unique operating point for a fuel cell system with the maximum output. Thus, a maximum power point tracking (MPPT) controller is needed to increase the efficiency of the fuel cell systems. In this paper an efficient method based on the particle swarm optimization (PSO) and PID controller (PSO-PID) is proposed for MPPT of the proton exchange membrane (PEM) fuel cells. The closed loop system includes the PEM fuel cell, boost converter, battery and PSO-PID controller. PSO-PID controller adjusts the operating point of the PEM fuel cell to the maximum power by tuning of the boost converter duty cycle. To demonstrate the performance of the proposed algorithm, simulation results are compared with perturb and observe (P&O) and sliding mode (SM) algorithms under different operating conditions. PSO algorithm with fast convergence, high accuracy and very low power fluctuations tracks the maximum power point of the fuel cell system.     

A maximum power point tracking for photovoltaic-SPE system using a maximum current controller

Processes to produce hydrogen from solar photovoltaic (PV)-powered water electrolysis using solid polymer electrolysis (SPE) are reported. An alternative control of maximum power point tracking (MPPT) in the PV-SPE system based on the maximum current searching methods has been designed and implemented.Based on the characteristics of voltage–current and theoretical analysis of SPE, it can be shown that the tracking of the maximum current output of DC–DC converter in SPE side will track the MPPT of photovoltaic panel simultaneously.This method uses a proportional integrator controller to control the duty factor of DC–DC converter with pulse-width modulator (PWM).The MPPT performance and hydrogen production performance of this method have been evaluated and discussed based on the results of the experiment.     

Perturbative methods for maximum power point tracking (MPPT) of photovoltaic (PV) systems: a review

Over the past few decades, the world demand for energy has risen steadily, forcing the world communities to look for alternative sources. Photovoltaic (PV) is seen as the most promising solution for this demand. However, the PV system is popularly known to suffer from low‐energy harvesting due to the change of environment conditions. An inexpensive and practical solution to extract the energy from the PV is by improving the maximum power point tracking (MPPT) controller technique. An ideal MPPT should be able to track the true maximum power operating point accurately under all circumstances and overcome all nonlinearities in the characteristic I‐V curves. This paper presents an updated review of the techniques based on the perturbative MPPT methods, both using the conventional and soft computing methods. The working principles of the techniques, parameter effects, and their limitations are discussed. The focus of this review is to direct the readers to the new direction of MPPT using the artificial intelligence and evolutionary computation techniques. Besides serving as a comprehensive source of information, the paper also provides a critical review on the relative performance of the selected MPPT methods. This includes the module dependency, tracking performance, and the ability to handle the partial shading conditions. Copyright © 2015 John Wiley & Sons, Ltd.     

Single-stage sine-wave inverter for an autonomous operation of solar photovoltaic energy conversion system

This paper proposes a high performance single-stage inverter topology for the autonomous operation of a solar photovoltaic system. The proposed configuration which can boost the low voltage of photovoltaic (PV) array, can also convert the solar dc power into high quality ac power for driving autonomous loads without any filter. An MPPT circuit with parallel connection is implemented so that the part of the energy generated is processed by the dc–dc converter to supply dc loads. The line current total harmonic distortion (THD) obtained using this configuration is quite reasonable. The proposed topology has several desirable features such as low cost and compact size as number of switches used, are limited to four as against six switches used in classical two-stage inverters. In this paper analysis, simulation and experimental results are presented.     

Grid connected fuel cell and PV hybrid power generating system design with Matlab Simulink

Renewable energy sources have been taken the place of the traditional energy sources and especially rapidly developments of photovoltaic (PV) technology and fuel cell (FC) technology have been put forward these renewable energy sources (RES) in all other RES. PV systems have been started to be used widely in domestic applications connected to electrical grid and grid connected PV power generating systems have become widespread all around the world. On the other hand, fuel cell power generating systems have been used to support the PV generating so hybrid generation systems consist of PV and fuel cell technology are investigated for power generating. In this study, a grid connected fuel cell and PV hybrid power generating system was developed with Matlab Simulink. 160 Wp solar module was developed based on solar module temperature and solar irradiation by using real data sheet of a commercial PV module and then by using these modules 800 Wp PV generator was obtained. Output current and voltage of PV system was used for input of DC/DC boost converter and its output was used for the input of the inverter. PV system was connected to the grid and designed 5 kW solid oxide fuel cell (SOFC) system was used for supporting the DC bus of the hybrid power generating system. All results obtained from the simulated hybrid power system were explained in the paper. Proposed model was designed as modular so designing and simulating grid connected SOFC and PV systems can be developed easily thanks to flexible design.     

Optimization of a fuzzy logic controller for PV grid inverter control using S-function based PSO

This paper presents implementation of particle swarm optimization (PSO) algorithm as a C-Mex S-function. The algorithm is used to optimize a 9-rule fuzzy logic controller (FLC) for maximum power point tracking (MPPT) in a grid-connected photovoltaic (PV) inverter. The FLC generates DC bus voltage reference for MPPT. A digital PI current control scheme in rotating dq-reference frame is used to regulate the DC bus voltage and reactive power. The proposed technique simplifies optimal controller design and ensures fast simulation speeds due to seamless integration with the simulation platform. Validity of the proposed method was verified using co-simulation in PSIM and MATLAB/Simulink. Simulation results show that the optimized FLC gives a better performance compared to fixed-step MPPT.