Characterization of NBR networks from stress–strain and swelling equilibrium measurements

An improved stress–strain (S/S) method based on rubber elasticity theory and swelling equilibrium measurements was used to investigate the S/S behavior and the solvent swelling properties of nitrile–butadiene rubber (NBR) and also to study the effects of varying the cure agent and the curing conditions on the crosslinking efficiency in NBR vulcanizates. The S/S curve of completely swollen NBR vulcanizates is, as expected, in agreement with rubber elasticity theory, while that of dry or partially swollen vulcanizates is well described by the Mooney-Rivlin equation. Determined in benzene, χ was 0.494, compared to 1.338 in cyclohexane and 2.124 in n-heptane. The degree of crosslinking and the crosslinking efficiency in the NBR vulcanizates, moles of crosslinks produced per mole of crosslinking agent employed in the formula, are largely dependent on the nature of the crosslinking agent used and increase in the following order: peroxide, sulfur tetramethylthiuram disulfide, sulfur N-cyclohexyl-2-benzothiazolesulfenamide, sulfur benzothiazyl disulfide, and finally tetramethylthiuram disulfide.     

Effects of the compatibilizer structural parameters on microstructural formation in ethylene–propylene–diene monomer rubber/ethylene–propylene–diene monomer rubber‐g‐maleic anhydride/organoclay nanocomposites

Nanocomposite vulcanizates based on ethylene–propylene–diene monomer rubber (EPDM) and organically modified montmorillonite with improved mechanical and barrier properties were prepared via a melt‐mixing process in the presence of maleic anhydride grafted ethylene–propylene–diene monomer rubber (EPDM‐g‐MAH) as an interfacial compatibilizer. The effects of the EPDM Mooney viscosity as the matrix and also the compatibilizer molecular weight and its maleation degree on the developed microstructure were also studied. The annealing of the vulcanized nanocomposites based on a low‐Mooney‐viscosity EPDM matrix and low‐Mooney‐viscosity EPDM‐g‐MAH enhanced the flocculation of the dispersed clay platelets; this implied that the flocculated structure for the clay nanolayers was more thermodynamically preferred in these nanocomposites. This was verified by the decrease in the oxygen permeability of the nanocomposite vulcanizates with increasing annealing time. The tendency of the clay nanosilicate layers to flocculate within the matrix of EPDM was found to be influenced by the clay volume fraction, the maleation degree, and also, the Mooney viscosity of the compatibilizer. Interfacially compatibilized nanocomposites based on high‐molecular‐weight EPDM exhibited a more disordered dispersion of the clay nanolayers, with a broadened relaxation time spectra; this was attributed to the higher shearing subjected to the mix during the melt‐blending process. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effect of bis(diisopropyl)thiophosphoryl disulfide on the covulcanization of styrene–butadiene rubber and ethylene–propylene–diene (monomer) blends

Covulcanization of elastomer blends constituting styrene–butadiene rubber (SBR) and ethylene–propylene–diene (monomer) rubber (EPDM) was successfully performed in the presence of reinforcing fillers like carbon black and silica by using a multifunctional rubber additive, bis(diisopropyl)thiophosphoryl disulfide (DIPDIS). The polarity of EPDM rubber was increased by a two‐stage vulcanization technique, which allowed the formation of rubber‐bound intermediates. In this way the migration of both curatives and reinforcing fillers in the EPDM–SBR blend could be controlled and cure rate mismatch could be minimized. The process significantly improved the physical properties of the blend vulcanizates. The phase morphology, as evident from the SEM micrographs, was indicative of the presence of a much more compact and coherent rubber matrix in the two‐stage vulcanizates. Different accelerator systems were studied to understand better the function and effectiveness of DIPDIS in developing homogeneity in the blends of dissimilar elastomers. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1231–1242, 2004     

Polymer–solvent interaction parameters and efficiency of crosslinking of ethylene–propylene copolymers

A study has been carried out of the vulcanization of ethylene–propylene copolymers having different propylene contents, by use of an organic peroxide. The polymersolvent interaction parameter μ, calculated by the Flory-Rehner equation from values of ν_e and v_r, was found to be a linear function of v_r with benzene as the swelling agent. Values of μ and their dependence upon v_r were independent of copolymer composition, at least within the limits of experimental error, for samples having a propylene content of 30–60 mole-%. The crosslinking efficiency of the peroxide used was found to depend considerably on copolymer composition, in agreement with the results found for dicumyl peroxide. Finally, sulfur as a crosslinking coagent was found to exert a large effect on the value of ν_e, calculated from the equilibrium retractive force of benzene-swollen specimens.     

Thermoplastic elastomers based on high‐density polyethylene,ethylene–propylene–diene terpolymer,and ground tire rubber dynamically vulcanized with dicumyl peroxide

Thermoplastic vulcanizates (TPVs) based on high‐density polyethylene (HDPE), ethylene–propylene–diene terpolymer (EPDM), and ground tire rubber (GTR) were dynamically vulcanized with dicumyl peroxide (DCP). The polymer blend was composed of 40% HDPE, 30% EPDM, and 30% GTR, and the concentration of DCP was varied from 0.3 to 3.6 parts per hundred rubber (phr). The properties of the TPVs were determined by evaluation of the gel fraction content and the mechanical properties. In addition, IR spectroscopy and differential scanning calorimetry analysis were performed as a function of the DCP content. Decreases in the Young's modulus of the blends and the crystallinity of HDPE were observed when the content of DCP was greater than 1.8 phr. The results regarding the gel content indicate that the presence of DCP promoted the crosslinking of the thermoplastic matrix, and optimal properties were obtained with 1.5% DCP. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39901.     

Optimization of accelerators on curing characteristics,tensile, and dynamic mechanical properties of (natural rubber)/(recycled ethylene‐propylene‐diene‐monomer) blends

The migration of sulfur from natural rubber (NR) compound to the ground waste ethylene‐propylene‐diene monomer (EPDM) rubber phase may have caused the cure incompatibility between these two rubbers. Optimization of accelerators had been adopted to overcome the cure incompatibility in NR/(R‐EPDM) blends as well as to get increased curative distribution. In this study, blends of NR and R‐EPDM were prepared. The effect of accelerator type on curing characteristics, tensile properties, and dynamic mechanical properties of 70/30/NR/(R‐EPDM) blend was investigated. Four types of commercial accelerators were selected [ie, N‐tert‐butyl‐2‐benzothiazyl‐sulphonamide , N‐cyclohexyl‐benzothiazyl‐sulfenamide (CBS), tetramethylthiuram disulfide, and 2‐mercaptobenzothiazol]. It was found that the tensile strength of the blends cured in the presence of CBS was relatively higher than the other three accelerators. Scanning electron micrographs of CBS‐cured NR/(R‐EPDM) blends exhibited more roughness and cracking path, indicating that higher energy was required toward the fractured surface. The high crosslinking density observed from the swelling method could be verified from the storage modulus (E′) and damping factor (tan δ) where (tetramethylthiuram disulfide)‐cured NR/(R‐EPDM) blends provided a predominant degree of crosslinking followed by N‐tert‐butyl‐2‐benzothiazyl‐sulphonamide , CBS, and 2‐mercaptobenzothiazol, respectively. J. VINYL ADDIT. TECHNOL., 21:79–88, 2015. © 2014 Society of Plastics Engineers     

Dynamic mechanical analysis of ethylene–propylene–diene monomer rubber and styrene–butadiene rubber blends

The effects of blend ratio, crosslinking systems, and fillers on the viscoelastic response of ethylene–propylene–diene monomer (EPDM)/styrene–butadiene rubber (SBR) blends were studied as functions of frequency, temperature, and cure systems. The storage modulus decreased with increasing SBR content. The loss modulus and loss tangent results showed that the EPDM/SBR blend vulcanizate containing 80 wt % EPDM had the highest compatibility. Among the different cure systems studied, the dicumyl peroxide cured blends exhibited the highest storage modulus. The reinforcing fillers were found to reduce the loss tangent peak height. The blend containing 40 wt % EPDM showed partial miscibility. The dispersed EPDM phase suppressed the glass‐transition temperature of the matrix phase. The dynamic mechanical response of rubbery region was dominated by SBR in the EPDM–SBR blend. The morphology of the blend was studied by means of scanning electron microscopy. The blend containing 80 wt % EPDM had small domains of SBR particles dispersed uniformly throughout the EPDM matrix, which helped to toughen the matrix and prevent crack propagation; this led to enhanced blend compatibility. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Thermal and mechanical properties of silicon rubber/cis‐polybutadiene rubber/ethylene–propylene–diene monomer blends

Considering the properties of silicon rubber, ethylene–propylene–diene monomer (EPDM), and cis‐polybutadiene rubber (BR), a blend made by a new method was proposed in this article; this blend had thermal resistance and good mechanical properties. The morphology of the blend was studied by SEM, and it was found that the adhesion between the phases of BR, EPDM, and polysiloxanes (silicon rubber) could be enhanced, and the compatibility and covulcanization were good. The influence of the mass ratio of peroxide and silica on the mechanical properties and thermal resistance of the blend was studied. The results showed that the mechanical properties and thermal resistance of the blend were improved when silicon rubber/BR/EPDM was 20/30/50, dicumyl peroxide/sulfur was 2.5/2.5, and the amount of silica was 80 phr. The integral properties of rubber blend had more advantages than did the three rubbers. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 4462–4467, 2006     

Natural rubber–ethylene‐propylene‐diene rubber covulcanization: Effect of reinforcing fillers

Filled covulcanizates of elastomer blend comprising natural rubber (NR) and ethylene‐propylene‐diene rubber (EPDM) of commercial importance were successfully prepared by using a multifunctional rubber additive; namely, bis(diisopropyl)thiophosphoryl disulfide (DIPDIS). A Two‐stage vulcanization technique further improved the physicochemical properties of the blend vulcanizates by restricting, through the formation of polar rubber bound intermediates, the migration of curative and filler from lower to highly unsaturated rubber. Scanning electron microscopy studies indicate homogeneity and coherency in the morphology of the two‐stage vulcanizates. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1001–1010, 2002; DOI 10.1002/app.10361     

Preparation and characterization of acrylonitrile–styrene–methylmethacrylate terpolymer as a compatibilizer for rubber blends

Acrylonitrile‐co‐styrene‐co‐methylmethacrylate (AN‐S‐MMA) terpolymer was prepared by bulk and emulsifier‐free emulsion polymerization techniques. The bulk and emulsion terpolymers were characterized by means of Fourierr transform infrared spectroscopy, ¹³C nuclear magnetic resonance (NMR) spectroscopy, gel permeation chromatography, thermal gravimetric analysis, and elemental analysis. The kinetics of the terpolymerization were studied. The terpolymers were then incorporated into butadiene—acrylonitrile rubber (NBR)/ethylene propylene diene monomer rubber (EPDM) blends and into chloroprene rubber (CR)/EPDM blend. The terpolymers were then tested for potential as compatibilizers by using scanning electron microscopy and differential scanning calorimetry. The terpolymers improved the compatibility of CR/EPDM and NBR/EPDM blends. The physicomechanical properties of CR/EPDM and NBR/EPDM blend vulcanizates revealed that the incorporation of terpolymers was advantageous, since they resulted in blend vulcanizates with higher 100% moduli and with more thermally stable mechanical properties than the individual rubbers. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3143–3153, 2003     

Mechanism of toughening for polypropylene blended with ethylene–propylene–diene rubber following selective crosslinking

Toughening mechanism of polypropylene (PP) blended with ethylene–propylene–diene rubber (EPDM) following selective crosslinking was examined in comparison with that of blends of PP before crosslinking. The yield stress, strength of craze, and density of void which are dominant factors for enhancing toughness in PP blends were evaluated and the deformation and fracture mechanism was discussed. It was concluded that toughness of PP blended with EPDM is improved by selective crosslinking, since the improvement of the craze strength is greater than the drop in the release of the constraint of strain. © 1996 John Wiley & Sons, Inc.     

Preparation and performances of ethylene–propylene–diene terpolymer/acrylic rubber reinforced with a dough‐modeling compound

A novel composite was prepared by the addition of a dough‐modeling compound (DMC) reinforcement and an ethylene–propylene–diene terpolymer (EPDM)/acrylic rubber (ACM) matrix. We studied the DMC/EPDM/ACM mass ratio and vulcanizing process by testing the tensile strength, Shore A hardness, elongation at break, and wear and thermal properties. The results show that the mechanical properties, thermal properties, and wear resistance of the composites were good when the DMC/EPDM/ACM mass ratio was 70/25/75 and the cure conditions were 180°C under 10 MPa for 25 min. The crosslinking structure of the composites was studied by IR, and this further proved the interaction between DMC, ACM, and EPDM. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

环氧化天然橡胶共交联改性EPDM/NR共混物的性能

将三元乙丙橡胶(EPDM)与环氧化天然橡胶(ENR)共交联改性后,再与天然橡胶(NR)共混,考察了ENR共交联改性EPDM/NR共混胶的硫化特性、硫化胶的物理机械性能、溶胀指数和耐热空气老化性能,并对该硫化胶进行了差示扫描量热分析。结果表明,EPDM经过ENR共交联改性后与NR共混,ENR共交联改性EPDM/NR共混胶的交联程度明显提高,各相达到了同步交联,硫化胶的综合性能得到了显著改善。     

Effect of anhydride‐modified ethylene–propylene–diene rubber and ethylene–vinyl acetate copolymers on the compatibilization of nitrile rubber/ethylene–propylene–diene rubber blends

The effects of maleic anhydride modified ethylene–propylene–diene rubber (EPDMMA) and maleic anhydride modified ethylene–vinyl acetate (EVAMA) on the compatibilization of nitrile rubber (NBR)/ethylene–propylene–diene rubber (70:30 w/w) blends vulcanized with a sulfur system were investigated. The presence of EPDMMA and EVAMA resulted in improvements of the tensile properties, whereas no substantial change was detected in the degree of crosslinking. The blend systems were also analyzed with scanning electron microscopy and dynamic mechanical thermal analysis. The presence of EVAMA resulted in a blend with a more homogeneous morphology. The compatibilizing effect of this functional copolymer was also detected with dynamic mechanical analysis. A shift of the glass‐transition temperature of the NBR phase toward lower values was observed. The presence of EPDMMA and EVAMA also increased the thermal stability, as indicated by an improvement in the retention of the mechanical properties after aging in an air‐circulating oven. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2408–2414, 2003     

Protection effects of condensed bromoacenaphthylene on radiation deterioration of ethylene–propylene–diene rubber

As a continuation of a series of the studies on the flame and γ-radiation resistant modification of ethylene–propylene–diene rubber (EPDM), condensed bromoacenaphthylene (con-BACN) as a newly developed flame retardant was synthesized and its effects on the radiation resistance of EPDM were investigated. The radiation resistance evaluated by measuring tensile properties of irradiated sheets of 2 mm thck was found improved greatly by adding con-BACN together with ordinary rubber ingredients but decreased by decabromodiphenylether (DBDPE) that has bromins in aromatic rings as con-BACN. When EPDM sheets of 1 mm thick were irradiated in oxygen at a dose rate of 1 × 10⁵ rad/h, the weight swelling ratio increased with increasing dose, indicating that oxidative main chain scission is predominant under the irradiation conditions. On the other hand, crosslinking was shown to be predominant in nitrogen. From the results of the swelling experiments with different additives, it was concluded that DBDPE accelerates both the main chain scission in oxygen and the crosslinking in nitrogen. In contrast to this, con-BACN reduced the chain scission in oxygen. This observation was accounted by the assumption that the influence of the oxidative chain scission is partly compensated by the concurrent crosslinking which takes place through additions of con-BACN to substrate polymers even in the presence of oxygen.     

Comparative behavior of in situ silica generation in saturated rubbers: EPDM and hydrogenated natural rubber

Role of carbon‐carbon double (C?C) bonds content and their position in ethylene‐propylene diene ter‐polymer (EPDM), hydrogenated natural rubber (HNR) and natural rubber (NR) on in situ silica formation using tetraethoxysilane (TEOS) as a silica precursor is comparatively investigated. Glass transition temperature (T_g ) reflecting rubber chain flexibility is found as an important factor for in situ silica generation via swelling method. Despite of similar solubility parameters, NR has higher TEOS‐swelling degree resulting in the higher in situ silica content (30.8 phr) than EPDM (3.50 phr) and HNR (10.4–17.6 phr) due to the higher T_g of EPDM and HNR providing the less chain flexibility to be swollen in TEOS solution. The morphological analysis implies that C?C bonds in saturated rubbers may be agglomeration sites for in situ silica particles. For practical applications, saturated rubbers containing in situ silica/NR vulcanizates showed the improvement of mechanical properties and resistance of thermal and ozone degradation. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44748.     

Effect of Bromination on Epdm Curing Behavior and its Tensile Properties

Ethylene propylene diene rubber (EPDM) was brominated. The curing behavior and tensile properties of the brominated EPDM (BEPDM) were investigated using a typical sulfur curing formulation. The brominated EPDM was observed to cure with a shorter cure induction time than the unbrominated one. The activation energies (E _a) of curing for EPDM and brominated EPDM were found to be approximately 145 kJ/mol and 58 kJ/mol, respectively. Analysis of curing behavior with individual curatives and stress-strain measurements indicates that these significant improvements could be attributed to the role of bromine as a more efficient crosslinking site, forming C—O—C crosslinks. In addition, the bromine also seems to increase the solubility of sulfur in the rubber, promoting sulfur crosslinks which are apparently not observed with the unbrominated EPDM. Consequently, the BEPDM displayed significantly higher tensile strength than the unbrominated one.     

Studies on ethylene‐propylene‐diene rubber modification by N‐chlorothio‐N‐butyl‐benzenesulfonamide

N‐Chlorothiosulfonamides have been used to modify ethylene‐propylene‐diene rubber (EPDM) to enhance the compatibility of EPDM in, e.g., natural rubber (NR)/butadiene rubber (BR)/EPDM blends for ozone resistance. N‐Chlorothio‐N‐butyl‐benzenesulfonamide (CTBBS) was selected as a representative for N‐chlorothiosulfonamides. In this study, we found that CTBBS behaves differently with various types of EPDM. Three types of EPDM were selected: ethylidene norbornene (ENB)‐EPDM, hexadiene (HD)‐EPDM, and dicyclopentadiene (DCPD)‐EPDM. HD‐EPDM showed the greatest effectiveness toward CTBBS‐modification. However, this EPDM is not commercially available anymore. On the opposite side, DCPD‐EPDM showed the lowest reactivity so that almost no modification could be realized. The result with ENB‐EPDM was, that upon application of CTBBS to ENB‐EPDM, gelation occurred and, therefore, a low amount of modification was achieved. With the limited modification efficiency for ENB‐EPDM, there is no significant improvement when applying the modified ENB‐EPDM into NR/BR/EPDM blends. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effects of peroxide and phenolic cure systems on characteristics of the filled ethylene–propylene–diene monomer rubber (EPDM)

The effects of three curing systems, peroxide, peroxide–phenolic combination, and phenolic on selected properties of cured carbon black‐filled ethylene–propylene–diene monomer rubber (EPDM) were investigated. The cured rubbers immersed in hot amine solution to evaluate their suitability for seal and gasket industry at elevated temperature and amine environments. These tests were essential for evaluating the durability of the gasket in a gas refinery. The Fourier transform infrared spectroscopy spectrums revealed that the phenolic crosslink was constructed between rubber macromolecules during the curing process. The changing curing system from peroxide to peroxide–phenolic and phenolic increased the glass transition temperature of the filled cured rubbers between 3 and 5 °C. There was not any significant difference between thermogravimetric analysis thermographs of the selected cured rubbers with various cure systems and the residues ranged between 45% and 47%. Unlike of peroxide curing system, a dual phase was observed from scanning electron microscopy micrographs for peroxide–phenolic and phenolic cure systems. The phenolic cure system was not beneficial for rubber curing although, it reduced scorch time of the curing process. For the most studied mechanical properties, phenolic cure system deteriorated mechanical properties for both, aged and unaged cured rubbers. Increasing the amount of diene monomer in EPDM structure was beneficial for phenolic rubber cure system. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46213.     

Structural characterization of reactor blends of polypropylene and ethylene‐propylene rubber

Blends of isotactic polypropylene (PP), ethylene‐propylene rubber copolymer (EPR), and ethylene‐propylene crystalline copolymer (EPC) can be produced through in situ polymerization processes directly in the reactor and blends with different structure and composition can be obtained. In this work we studied the structure of five reactor‐made blends of PP, EPR, and EPC produced by a Ziegler‐Natta catalyst system. The composition of EPR was related to the ratio between ethylene and propylene used in the copolymerization step. The ethylene content in the EPR was in the range of 50–70 mol %. The crystallization behavior of PP and EPC in the blends was influenced by the presence of the rubber, and some specific interactions between the components could be established. By preparative temperature rising elution fractionation (P‐TREF) analysis, the isolation and characterization of crystalline EPC fractions were made. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2155–2162, 2004