Epoxy resin containing poly(ethylene oxide)-block-poly(?-caprolactone) diblock copolymer: Effect of curing agents on nanostructures

An amphiphilic diblock copolymer, poly(ethylene oxide)-block-poly(?-caprolactone) (PEO-b-PCL) was synthesized via the ring-opening polymerization of ?-caprolactone in the presence of a hydroxyl-terminated poly(ethylene oxide) monomethyl ether. The diblock copolymer was incorporated into epoxy thermosets. It is found that the formation of nanostructures of thermosetting blends is quite dependent on the uses of aromatic amine hardeners. For 4,4′-methylenebis(2-chloroaniline) (MOCA)-cured thermosetting system, the homogeneous morphology was obtained at the compositions investigated. Nonetheless, the nanostructured thermosets were obtained when the blends were cured with 4,4′-diaminodiphenylsulfone (DDS). The differential scanning calorimetry (DSC) showed that the nanostructured thermosets did not displayed any crystallinity although the subchains of the diblock copolymer are crystalline. The nanostructures were evidenced by means of atomic force microscopy (AFM), small-angle X-ray scattering (SAXS) and transmission electron microscopy (TEM). The dependence of morphological structures on the types of aromatic amines for epoxy and PEO-b-PCL thermosetting blends were interpreted on the basis of the difference in hydrogen bonding interactions resulting from the structure of curing agents. Considering the complete miscibility of the subchains (viz. PEO and PCL) with the precursors of epoxy resin before curing, it is judged that the formation of the nanostructures in the thermosets follows the mechanism of reaction-induced microphase separation, which is in marked contrast to the mechanism of self-assembly, i.e., micelle structures of block copolymers are formed prior to curing, followed by fixing these nanostructures via curing.     

Effects of micelle structures formed in selective solvents on crystallization behaviors of poly(ethylene glycol)-b-poly(styrene) copolymers

Well-defined amphiphilic block copolymers, poly(ethylene glycol) methyl ether-b-poly(styrene) (mPEG-b-PS), in which the PS blocks had different molecular weights, were synthesized by atom transfer radical polymerization (ATRP). Through introduction of selective solvents for the blocks, crystalline and amorphous blocks were self-assembled into different micelle structures in solutions. Atomic force microscopy (AFM) was used to characterize the micelle structures. It was observed that spherical micelles were always formed, whereas lamellar aggregates appeared only in the PS-selective solvent when the molecular weight of the PS block in mPEG-b-PS was low. The crystallizable mPEG blocks were self-assembled into either the core or corona of the micelles formed. The effects of the self-assembled structures on the crystallization behavior of mPEG blocks were then investigated with differential scanning calorimeter (DSC). When the PS molecular weight was much larger than that of mPEG, the result showed that the crystallinity of the mPEG block was lower when mPEG blocks crystallized in the corona than that in the core of the micelles. In this case, when mPEG blocks crystallized in micelle coronae, the micelle core formed by insoluble PS blocks was very big, so mPEG chains had to distribute sparsely in the micelle coronae. It was hard for mPEG chains in one micelle or among different micelles to gather together to crystallize. However, when the PS molecular weight was lower than that of mPEG, the crystallinity of mPEG was higher when the mPEG chains crystallized in the micelle corona, as the core formed by insoluble PS was small and the mPEG chains in the corona were easy to aggregate and crystallize.     

Ionic conductivity in polyethylene-b-poly(ethylene oxide)/lithium perchlorate solid polymer electrolytes

The ionic conductivity and phase arrangement of solid polymeric electrolytes based on the block copolymer polyethylene-b-poly(ethylene oxide) (PE-b-PEO) and LiClO₄ have been investigated. One set of electrolytes was prepared from copolymers with 75% of PEO units and another set was based on a blend of copolymer with 50% PEO units and homopolymers. The differential scanning calorimetry (DSC) results, for electrolytes based on the copolymer with 75% of PEO units, were dominated by the PEO phase. The PEO block crystallinity dropped and the glass transition increased with salt addition due to the coordination of the cation by PEO oxygen. The conductivity for copolymers 75% PEO-based electrolyte with 15 wt% of salt was higher than 10⁻⁵ S/cm at room temperature and reached to 10⁻³ S/cm at 100 °C on a heating measurement. The blend of PE-b-PEO (50% PEO)/PEO/PE showed a complex thermal behavior with decoupled melting of the blocks and the homopolymers. Upon salt addition the endotherms associated with PEO domains disappeared and the PE crystals remained untouched. The conductivity results were limited at 100 °C to values close to 10⁻⁴ S/cm and at room temperature values close to 3 × 10⁻⁶ S/cm were obtained for the 15 wt% salt electrolyte. Raman study showed that the ionic association of the highly concentrated blend electrolytes at room temperature is not significant. Therefore, the lower values of conductivity in the case of the blend with 50% PEO can be assigned to the higher content of PE domains leading to a morphology with lower connectivity for ionic conduction both in the crystalline and melted state of the PE domains.     

The effect of polystyrene-block-poly(4-vinylpyridine) prepared by a RAFT method in the dispersion polymerization of MMA

The dispersion polymerization of methyl methacrylate (MMA) has been carried out using polystyrene-block-poly(4-vinylpyridine) copolymer [P(S-b-4VP)], which was prepared by a reversible addition-fragmentation chain transfer (RAFT) method, as a steric stabilizer in an alcohol media. The stable polymer particles were obtained when the block copolymer concentrations increased from 1 to 10 wt% relative to the monomer and the average particle sizes decreased from 5.3 to 3.4 μm with the increasing concentration of the block copolymer. In particular, the incorporation of 2 wt% polystyrene-block-poly(4-vinylpyridine) produced 4.3 μm of monodisperse PMMA particles with 2.14% of C_v. Thus, the P(S-b-4VP) block copolymer prepared by the RAFT method is working not only as a steric stabilizer, but also in providing monodisperse micron-sized PMMA particles.     

Study of interfacial tension in poly(ethylene oxide)/polystyrene/diblock copolymer system by electric deformation method

We investigated the interfacial tension γ between poly(ethylene oxide) (PEO) and polystyrene (PS) focusing our attention on the dependence of γ on the molecular weight (M) of PEO and the surfactant effect of poly(ethylene oxide-b-styrene) diblock copolymer [P(EO-b-S)]. Measurements of γ were carried out by observing electric deformation of droplets of PEO suspended in bulk PS or in a concentrated solution of PS in dioctylphthalate (DOP). The results indicate that γ between PEO and PS is almost independent of M of PEO in the high molecular weight region, but exhibits a minimum around M = 500. Addition of 1 wt% of P(EO-b-S) to the PEO/PS system causes a decrease of γ due to the surfactant effect of the copolymer, but γ is almost independent of further addition of the copolymer. The decrement of the interfacial tension Δγ increases with increasing molecular weight of P(EO-b-S).     

Poly(ethylene oxide)-grafted poly(N-isopropylacrylamide) networks: Preparation, characterization and rapid deswelling and reswelling behavior of hydrogels

Poly(ethylene oxide)-grafted poly(N-isopropylacrylamide) networks (PNIPAAm-g-PEO) were prepared via the reversible addition-fragmentation chain transfer polymerization (RAFT) of N-isopropylacrylamide with trithiocarbonate-terminated poly(ethylene oxide) and N,N′-methylenebisacrylamide as the chain transfer agent and the crosslinking agent, respectively. It was found that the PNIPAAm-g-PEO copolymer networks were microphase-separated and that PEO microdomains were dispersed in the PNIPAAm matrix. The hydrogel behavior of the PNIPAAm-g-PEO networks was investigated using swelling, deswelling and reswelling tests. The PNIPAAm-g-PEO hydrogels displayed faster responses to external temperature changes than did the control PNIPAAm hydrogel.     

Double-responsive core-shell-corona micelles from self-assembly of diblock copolymer of poly(t-butyl acrylate-co-acrylic acid)-b-poly(N-isopropylacrylamide)

Self-assembly of poly(t-butyl acrylate-co-acrylic acid)-b-poly(N-isopropylacrylamide) [P(tBA-co-AA)-b-PNIPAM], which was obtained from part hydrolysis of PtBA-b-PNIPAM synthesized by sequential atom transfer radical polymerization (ATRP) was studied. Thermo- and pH-responsive core-shell-corona (CSC) micelles with different structures were formed from (PtBA-co-PAA)-b-PNIPAM in aqueous solution. At pH 5.8 and 25 °C, the block copolymer self-assembled into spherical core-shell micelles with hydrophobic PtBA segments as the core, hydrophilic PAA/PNIPAM segments as the mixed shell. Increasing temperatures, core-shell micelles converted into CSC micelles with PtBA as the core, collapsed PNIPAM as the shell and soluble PAA as the corona. Moreover, decreasing pH at 25 °C, PAA chains collapsed onto the core resulting in CSC micelles with PtBA as the core, PAA as the shell and PNIPAM as the corona.     

Phase inversion membranes with an organized surface structure from mixtures of polysulfone and polysulfone—poly(ethylene oxide) block copolymers

Phase inversion precipitation of a polysulfone and polysulfone—poly(ethylene oxide) block copolymer solution yields a membrane with an organized surface structure. The poly(ethylene oxide) block of the polysulfone—poly(ethylene oxide) block copolymer segregates to the surface of the membrane. Measurement of the ¹H T_1ρ of the component materials, X-ray photoelectron spectroscopy, and differential scanning calorimetry reveal the organized surface structure of the membrane. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 66: 1353–1358, 1997     

Crystallization and vitrification effect in a poly(styrene)-g-poly(ethylene oxide) graft copolymer

Crystallization and solid state structure of a poly(styrene)-graft-poly(ethylene oxide) (PS-g-PEO) graft copolymer with crystallizable side chains were studied using simultaneous small angle X-ray scattering/wide angle X-ray scattering/differential scanning calorimetry (SAXS/WAXS/DSC). It is found that the glass transition temperature (T_g) of PS main chain is remarkably higher than that of PS homopolymer. The start cooling temperature (T_o) has a great influence on crystallization of the PEO side-chain. When the graft copolymer is cooled from the temperature above T_g, phase separation is suppressed due to the low mobility of the PS main chain and the homogeneous melt is vitrified. The unfavorable conformation of the rigid main chain results in a single crystallization peak and lower crystallinity. When PS-g-PEO is only heated to a temperature lower than the T_g and then cooled, phase separation is retained. Both the PEO side chains with high and low crystallizability can crystallize in the phase-separated state, leading to double crystallization peaks and higher crystallinity. The effect of solvent on crystallization of the graft copolymer was also examined. It is observed that addition of toluene reduces the T_g of the PS main chain and leads to the disappearance of the vitrification effect.     

Preparation and characterization of amphiphilic block copolymer of polyacrylonitrile‐block‐poly(ethylene oxide)

The synthesis of polyacrylonitrile‐block‐poly(ethylene oxide) (PAN‐b‐PEO) diblock copolymers is conducted by sequential initiation and Ce(IV) redox polymerization using amino‐alcohol as the parent compound. In the first step, amino‐alcohol potassium with a protected amine group initiates the polymerization of ethylene oxide (EO) to yield poly(ethylene oxide) (PEO) with an amine end group (PEO‐NH₂), which is used to synthesize a PAN‐b‐PEO diblock copolymer with Ce(IV) that takes place in the redox initiation system. A PAN‐poly(ethylene glycol)‐PAN (PAN‐PEG‐PAN) triblock copolymer is prepared by the same redox system consisting of ceric ions and PEG in an aqueous medium. The structure of the copolymer is characterized in detail by GPC, IR, ¹H‐NMR, DSC, and X‐ray diffraction. The propagation of the PAN chain is dependent on the molecular weight and concentration of the PEO prepolymer. The crystallization of the PAN and PEO block is discussed. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1753–1759, 2003     

Synthesis and physical gels of pH- and thermo-responsive tertiary amine methacrylate based ABA triblock copolymers and drug release studies

A series of novel pH-responsive ABA triblock copolymer gelators have been synthesized by using poly[2-(diisopropylamino)ethyl methacrylate] (PDPA) as the A block and poly[2-(dimethylamino)ethyl methacrylate] (PDMA) as the B block via group transfer polymerization. While the PDPA-b-PDMA-b-PDPA triblock copolymers are molecularly soluble in acidic aqueous media due to protonation of all tertiary amine groups, they formed either gels by the chain-end hydrophobic interactions with relatively high polymer concentration (10 wt%) or near monodisperse “flower” micelles with low polymer concentration at neutral and basic aqueous solutions. The hydrophobic model drug release was studied in a sustained manner from the gels at pH 7.4 by varying the polymer concentration, the polymer molecular weight and the temperature of the medium. Preliminary studies indicate that both slow, sustained release and fast, triggered release of a model hydrophobic drug, dipyridamole, can be achieved by tuning the solution pH, polymer concentration, polymer molecular weight and temperature of the gel.     

Synthesis of poly(ethylene oxide)-block-poly(methyl methacrylate)-block-polystyrene triblock copolymers by two-step atom transfer radical polymerization

The synthesis of ABC triblock copolymer poly(ethylene oxide)-block-poly(methyl methacrylate)-block-polystyrene (PEO-b-PMMA-b-PS) via atom transfer radical polymerization (ATRP) is reported. First, a PEO-Br macroinitiator was synthesized by esterification of PEO with 2-bromoisobutyryl bromide, which was subsequently used in the preparation of halo-terminated poly(ethylene oxide)-block-poly(methyl methacrylate) (PEO-b-PMMA) diblock copolymers under ATRP conditions. Then PEO-b-PMMA-b-PS triblock copolymer was synthesized by ATRP of styrene using PEO-b-PMMA as a macroinitiator. The structures and molecular characteristics of the PEO-b-PMMA-b-PS triblock copolymers were studied by FT-IR, GPC and ¹H NMR.     

Double Stimuli-Responsive di- and Triblock Copolymers of Poly(N-isopropylacrylamide) and Poly(1-vinylimidazole): Synthesis and Self-Assembly

For the first time, double stimuli-responsive properties of poly(N-isopropylacrylamide) (PNIPA) and poly(1-vinylimidazole) (PVIM) block copolymers in aqueous solutions were studied. The synthesis of PNIPA₆₀-b-PVIM₉₀ and PNIPA₂₈-b-PVIM₆₂-b-PNIPA₂₉ was performed using reversible addition–fragmentation chain transfer (RAFT) polymerization. The polymers were characterized by size exclusion chromatography and ¹H NMR spectroscopy. The conformational behavior of the polymers was studied using dynamic light scattering (DLS) and fluorescence spectroscopy (FS). It was found that PNIPA and block copolymers conformation and ability for self-assembly in aqueous medium below and above cloud point temperature depend on the locus of hydrophobic groups derived from the RAFT agent within the chain. Additionally, the length of PVIM block, its locus in the chain and charge perform an important role in the stabilization of macromolecular micelles and aggregates below and above cloud point temperature. At 25 °C the average hydrodynamic radius (R_h) of the block copolymer particles at pH 3 is lower than at pH 9 implying the self-assembling of macromolecules in the latter case. Cloud points of PNIPA₆₀-b-PVIM₉₀ are ~43 °C and ~37 °C at a pH of 3 and 9 and of PNIPA₂₈-b-PVIM₆₂-b-PNIPA₂₉ they are ~35 °C and 31 °C at a pH of 3 and 9. Around cloud point independently of pH, the R_h value for triblock copolymer rises sharply, achieves the maximum value, then falls and reaches the constant value, while for diblock copolymer, it steadily grows after reaching cloud point. The information about polarity of microenvironment around polymer obtained by FS accords with DLS data.     

Controllable synthesis of poly(N-vinylpyrrolidone) and its block copolymers by atom transfer radical polymerization

At room temperature atom transfer radical polymerization (ATRP) of N-vinylpyrrolidone (NVP) was carried out using 5,5,7,12,12,14-hexamethyl-1,4,8,11-tetra-azacyclo-tetradecane (Me₆Cyclam) as ligand in 1,4-dioxane/isopropanol mixture. Methyl 2-chloropropionate (MCP) and copper(I) chloride were used as initiator and catalyst, respectively. The polymerization of NVP via ATRP could be mediated by the addition of CuCl₂. The resultant poly(N-vinylpyrrolidone) (PNVP) has high conversion of up to 65% in 3 h, a controlled molecular weight close to the theoretical values and narrow molecular weight distribution between 1.2 and 1.3. The living nature of the ATRP for NVP was confirmed by the experiments of PNVP chain extension. With PNVP-Cl as macroinitiator and N-methacryloyl-N′-(α-naphthyl)thiourea (MANTU) as a hydrophobic monomer, novel fluorescent amphiphilic copolymers poly(N-vinylpyrrolidone)-b-poly(N-methacryloyl-N′-(α-naphthyl)thiourea) (PNVP-b-PMANTU) were synthesized by ATRP. PNVP-b-PMANTU copolymers were characterized by ¹H NMR, GPC-MALLS and fluorescence measurements. The results revealed that PNVP-b-PMANTU presented a blocky architecture.     

One-pot synthesis of poly(N-vinylcaprolactam)-based biocompatible block copolymers using a dual initiator for ROP and RAFT polymerization

Thermosensitive, biocompatible poly(ε-caprolactone)-b-poly(N-vinylcaprolactam) (PCL-b-PVCL), poly(δ-valerolactone)-b-PVCL, and poly(trimethylene carbonate)-b-PVCL block copolymers were synthesized at 30 °C using a hydroxyl-functionalized xanthate reversible addition-fragmentation chain transfer (RAFT) agent, 2-hydroxyethyl 2-(ethoxycarbonothioylthio)propanoate (HECP), as a dual initiator for ring-opening polymerization (ROP) and RAFT polymerization in a one-pot procedure. The hydrophobic blocks were first synthesized by the ROP of cyclic monomers using diphenyl phosphate (DPP) as a catalyst and the RAFT polymerization of the PVCL block was followed by adding N-vinylcaprolactam (VCL) and 2,2′-azobis(4-methoxy-2,4-dimethyl valeronitrile) (V-70) as an initiator to the reaction mixture. This novel one-pot process is convenient and powerful method for the synthesis of the PVCL-based biocompatible block copolymers. The lower critical solution temperature (LCST) of the PVCL-based biocompatible block copolymer can be readily tuned by controlling the hydrophobicity of the block copolymers. By copolymerizing a hydrophilic N-vinylpyrrolidone moiety to the PVCL blocks by RAFT copolymerization, the LCST of the copolymer was matched with the body temperature for its future biomedical applications.     

Formation mechanism, chain folding, and growth behavior of the intriguing fiber-like crystal of poly (ethylene oxide-b-ε-caprolactone) block copolymer in ultrathin films

The morphologies, crystallization behavior and chain orientation of a highly asymmetric poly (ethylene oxide-b-ε-caprolactone) (PEO-b-PCL) block copolymer ultrathin films were investigated by using wide-angle X-ray diffraction (WAXD), atomic force microscopy (AFM) and grazing incidence X-ray diffraction (GIXRD) techniques. It is shown that the intriguing fiber-like crystal which seems to be an individual flat-on lamella was first observed in PEO-b-PCL ultrathin film according to our knowledge. The possible mechanism of forming the fiber-like crystals is chiefly ascribed to the rather low molecular weight of PEO-b-PCL and the mutual interaction between crystallization and microphase separation. At the same time, solution concentration and substrate surface energy play a crucial role. Subsequently, chain folding of the fiber-like crystal of PEO-b-PCL in ultrathin films was deduced based on the cell parameters and the lamellar thickness. Isothermal crystallization tests revealed that in the whole growth process, the crystal growths can be divided into two stages, both of which followed the diffusion-limited (DL) mechanism.     

Preparation of hydrogel nanoparticles by atom transfer radical polymerization of N-isopropylacrylamide in aqueous media using PEG macro-initiator

PEG-b-PNIPAM block copolymers are synthesized by the atom transfer radical polymerization of NIPAM using PEG macro-initiator. When the polymerization temperature is 25 °C, the block copolymer is soluble in water, whereas the block copolymer is phase-separated to form micelles during polymerization as the polymerization temperature is raised to 50 °C, the temperature above the LCST of PEG-b-PNIPAM. To prepare stable hydrogel nanoparticles in water at room temperature, a small amount of N,N′-ethylenebisacrylamide is added as a cross-linker to the reaction system, where the size of nanoparticles is controlled by the composition of mixed solvent.     

Aggregation of biodegradable amphiphilic poly(succinimide-co-N-propyl aspartamide) and poly(N-dodecyl aspartamide-co-N-propyl aspartamide) in aqueous medium and its preliminary drug-released properties

Two series of biodegradable amphiphilic copolymers, poly(succinimide-co-N-propyl aspartamide) (PSI-PA) and poly(N-dodecyl aspartamide-co-N-propyl aspartamide) (PDDA-PA) were synthesized by partial and total aminolysis of polysuccinimide (PSI), respectively. PSI-PA copolymers could self-aggregate in water directly under ultrasonication at room temperature. Differing from PSI-PA copolymers, the aggregates of PDDA-PA need to add PDDA-PA DMF solution into an excessive amount of water. The aggregative properties of PSI-PA and PDDA-PA copolymers have been investigated by dynamic light scattering (DLS) and surface tension measurements. Hydrophilicity of these two copolymers was attributed to the N-propyl aspartamide segments. Due to the stiff structure, succinimide segments preferred to form irregular hydrophobic microdomains, and some aggregates of PSI-PA are bimodal size distribution in water medium, while the more flexible PDDA-PA copolymer chains preferred to form monodispersed spherical aggregates. Elevated temperature could reduce the aggregate size of both PSI-PA and PDDA-PA copolymers due to the breaking of the hydrogen bonding and the releasing of the bonded water molecules. PSI-PA copolymers were surface active, while the surface tension of PDDA-PA copolymers was independent on concentration. The drug-loaded aggregates of PSI-PA also have been prepared and the preliminary release properties have been studied in vitro.     

Association behavior of thermo-responsive block copolymers based on poly(vinyl ethers)

Thermo-sensitive nanosized structures have been prepared in water from poly(methyl vinyl ether)-block-poly(isobutyl vinyl ether) (PMVE-b-PIBVE) block copolymers. The composition and the architecture (diblock and triblock architectures) of the PMVE-b-PIBVE copolymers have been varied. The investigated copolymers had an asymmetric composition with a major PMVE block. While the PIBVE blocks are hydrophobic, the PMVE blocks are hydrophilic at room temperature and become hydrophobic above their demixing temperature (around 36 °C) as a result of the lower critical solution temperature (LCST) behavior. At room temperature, the amphiphilic copolymers aggregate in water above a critical micelle concentration, which has been experimentally measured by hydrophobic dye solubilization. The hydrodynamic diameter of the structures formed above the cmc has been measured by dynamic light scattering (DLS) while their morphology has been studied by transmission electron microscopy (TEM). ¹H NMR measurements in D₂O at room temperature reveal that the aggregates contain PIBVE insoluble regions surrounded by solvated PMVE chains. These investigations have shown that polydisperse spherical micelles are formed for asymmetric PMVE-b-PIBVE copolymers containing at least 9 IBVE units. For copolymers containing less IBVE units, loose aggregates are formed.Finally, the thermo-responsive, reversible properties of these structures have been investigated. Above the cloud point of the copolymers, the loose aggregates precipitate while the micelles form large spherical structures.     

Shell-core-corona aggregates formed from poly(styrene)-poly(4-vinylpyridine) block copolymer induced by added homopolymer via interpolymer hydrogen-bonding

The solution behavior of poly(styrene)-poly(4-vinylpyridine) (PS-b-P4VP) block copolymer with added poly(4,4′-oxydiphenylenepyromellitamic acid) (POAA) homopolymer in DMF is studied by dynamic light scattering (DLS), nuclear magnetic resonance (NMR), and transmission electron microscopy (TEM). It is found that coaggregation takes place when mixing PS-b-P4VP block copolymer and POAA homopolymer in DMF due to the strong interpolymer hydrogen-bonding between POAA chains and P4VP blocks. The coaggregation is a diffusion-controlled process and the complexation-induced aggregates are very stable. NMR measurements demonstrate that the resultant aggregates are much more swollen compared with typical amphiphilic block copolymer core-shell micelles. DLS measurements with Eu³⁺ as a probe combined with TEM observation, are employed to study the structure of the aggregates. Results reveal that the formed aggregates are core-shell spheres with the P4VP/POAA complexes as core and the PS blocks as shell when the weight ratio of POAA to PS-b-P4VP is lower. However, a core-shell-corona structure forms with a thin layer of POAA chains adsorbed on the initial core-shell aggregates with increasing weight content of POAA to 60%. Finally, possible mechanisms of the structural transitions are proposed.