Polymorphism and β-form structure of poly(octamethylene 2,6-naphthalate)

It was revealed that poly(octamethylene 2,6-naphthalate) (PON) existed in two different crystal structures, α- and β-form, depending on crystallization process: The α-form crystal was dominantly developed from the cold-crystallization, whereas the β-form was from the melt-crystallization. The apparent melting temperatures of α- and β-form crystals were characterized to be 175 and 183 °C, respectively. On the basis of X-ray diffraction and molecular modeling studies, the crystal structure of β-form, developed dominantly from the melt-crystallization, was identified to be triclinic with dimensions of a = 0.601 nm, b = 1.069 nm, c = 2.068 nm, α = 155.68°, β = 123.25°, γ = 52.85°, and with the space group of . The calculated crystal density was 1.243 g/cm³, supporting that one repeating unit of PON exists in a unit cell. The octamethylene units in the PON backbone take largely all-trans conformation in the β-form unit cell.     

Crystal structure identification of poly(trimethylene 2,6-naphthalate) β-form crystal by X-ray diffraction and molecular modeling

X-ray powder diffraction and molecular modeling are used to identify the crystal structure and chain conformation of poly(trimethylene 2,6-naphthalate) (PTN) β-form crystal. The unit cell of PTN β-form crystal was determined to be a triclinic with dimensions of α=100.85°, β=88.78° and γ=120.63°, and the space group of the crystal is identified as The observed crystal density of 1.37 g cm⁻³ and the determined dimensions of unit cell indicate that the unit cell contains one polymer chain with two repeating units. In the unit cell, each trimethylene unit in PTN backbone is in gauche/gauche conformation and neighboring naphthalene units are in face-to-face type arrangement, forming π-stacks that lead to the lowest energy of the unit cell.     

Molecular and crystal structure of poly(tetramethylene adipate) α form based on synchrotron X-ray fiber diffraction

The molecular and crystal structure of the α form of poly(tetramethylene adipate) (PTMA) was analyzed using synchrotron X-ray fiber diffraction data. The crystals belong to the monoclinic system of space group P2₁/n. The unit cell constants are a=0.6776(6), b=0.7904(6), c (fiber axis)=1.442(1) nm and β=135.6(1)°. The final crystal structure was obtained by the linked-atom least-squares refinement, which gave an R-factor of 0.130 for 103 observed spots and 64 unobserved reflections. The molecular structure deviates slightly from the fully extended conformation in the ester part. The torsional angle CH₂-CH₂-O-C(O) was found to be 155°. The CO groups of the corner and center chains in a unit cell are closely located along the c-axis and are related by the crystallographic 2₁-axes along the b-axis at z=1/4 and z=3/4. The total dipole moment arising from the CO groups is oriented in one direction at z=1/4, and in the opposite direction at z=3/4. Owing to the close arrangement of the CO groups between neighboring chains along the fiber axis, the c-projected cell dimensions and the setting angle of the polymer chain are different from those of the orthorhombic form of polyethylene and the β form of PTMA.     

Molecular ordering and α′-form formation of poly(l-lactide) during the hydrolytic degradation

Hydrolytic degradation ability is an intriguing characteristic of poly(l-lactide) (PLLA) and it has been intensively investigated recently. However, the microstructure evolution of PLLA during the early stage of the hydrolytic degradation process is neglected. In this work, amorphous PLLA was hydrolyzed in alkaline media at temperatures from 40 to 60 °C. The variations of weight loss and molecular weight were measured to study the degree of the hydrolytic degradation of PLLA. The effect of hydrolytic degradation on microstructure of the amorphous PLLA was investigated by differential scanning calorimetry (DSC), Fourier transform infrared spectroscope (FTIR), wide angle X-ray diffraction (WAXD) and scanning electron microscope (SEM). The results clearly proves the occurrence of molecular ordering and the formation of α′-form PLLA, which is greatly related to the hydrolytic degradation conditions. At relatively low hydrolytic degradation temperature (40 and 50 °C), locally ordered structure is provoked, while a large number of α′-form crystallites are induced at relatively high temperature (60 °C). This work is very significant in understanding the microstructure evolution of PLLA during the hydrolytic degradation process.     

Incorporation of the transition metals (Cr and Fe) into β-SiAlON crystal structure

Outstanding properties for SiAlON ceramics can be obtained by tailoring the microstructure through α-SiAlON and β-SiAlON phase content as well as a type of secondary phases. It is so far well known that while some of the elements could be accommodated in α-SiAlON structure, β-SiAlON does not easily accommodate different elements in its structure. In this work, SiAlON ceramics were produced by using β-Si₃N₄ starting powder containing small amount of iron and chromium and the possible incorporation of iron and chromium into β-SiAlON structure was investigated by using analytical transmission electron microscopy (TEM) techniques. As a result of analytical TEM analysis, it is found that transition metals (Cr and Fe) can enter into the β-SiAlON crystal structure.     

Synthesis and characterization of polyrotaxanes comprising α-cyclodextrins and poly(ε-caprolactone) end-capped with poly(N-isopropylacrylamide)s

Biodegradable polyrotaxane (PR)-based triblock copolymers were synthesized via the atom transfer radical polymerization (ATRP) of N-isopropylacrylamide (NIPAAm) initiated with polypseudorotaxanes (PPRs) consisting of a distal 2-bromopropiomyl bromide end-capping poly(ε-caprolactone) (Br-PCL-Br) and a varying amount of α-cyclodextrins (α-CDs) in the presence of Cu(I)Br/PMDETA at 25 °C in aqueous solution. The copolymers were featured by relatively higher yields from 46.0% to 82.8% as compared with previous reports. Their structure was characterized in detail by using ¹H NMR, ¹³C CP/MAS NMR, GPC, WXRD, DSC and TGA analyses. When a feed molar ratio of NIPAAm to Br-PCL-Br was changed from 50 to 200, the degree of polymerization of PNIPAAm blocks attached to two ends of PPRs was in a range of 158–500. About one third of the added α-CDs were still entrapped on the central PCL chain after the ATRP process. Attaching PNIPAAm rendered the copolymers soluble in aqueous solution showing the thermo-responsibility as evidenced by turbidity measurements.     

Synthesis and crystal structure of 1,4-diaminobutyl-N,N′-bis(cyanoborane): the first substituted-borane adduct of putrescine

The reaction of 1,4-diaminobutane (putrescine) with two molar equivalents of trimethylaminecyanoborane in anhydrous diethyl ether, produced an unprecedented cyanoborane species, 1,4-diaminobutyl-N,N^′-bis(cyanoborane) (1), in 78% yield, via a Lewis-base exchange reaction. The crystal structure showed the title compound (1) to be a zwitterionic species in which the two nitrogen atoms of a putrescine unit are coordinated to two cyanoborane units.     

Synthesis of new diacid monomers and poly(amide-imide)s: study of structure–property relationship and applications

Two diimide-diacid monomers 4,4′-bis[4″-(trimellitimido)phenyl isopropylidene-4″′-phenoxy]diphenyl sulfone and 4,4′-bis[4″-(trimellitimido)phenylisopropylidene-4″′-phenoxy] were synthesized. The structures of the monomers were characterized by FT-IR and ¹H-NMR spectroscopy. A series of novel poly(amide-imide)s were prepared from this two diacids and aromatic diamines through phosphorylation reaction. The PAIs were characterized by FT-IR, ¹H-NMR, XRD, TGA, and DSC, solution viscosity, solubility test and electrical properties. Poly(amide-imide)s showed excellent solubility due to the presence of flexible groups and isopropylidene unit in the polymer backbone. They also exhibited good thermal stability and the temperatures at which 10% weight loss occurred in the range 385–465 °C. These PAIs found to have a dielectric constant in the range 3.25–4.20 at 10 kHz and have excellent electrical insulation character and can be used as insulation materials for electrical items operating at elevated temperatures.     

Crystal transformation from the α- to the β-form upon tensile drawing of poly(l-lactic acid)

A film of poly(l-lactic acid) (PLLA) consisting of highly oriented α crystals was uniaxially drawn by tensile force. The effects of the draw ratio (DR), draw temperature (T_d), and draw stress on the crystal/crystal transformation from the α- to the β-form crystals were studied. At the initial stage of drawing, the highly oriented α crystals of the starting film transformed into a broader orientation distribution, and significant crystal disorder was introduced. Upon further drawing, the α crystals steadily transformed into β crystals with increasing the DR. For the drawing at a constant T_d, the crystal transformation proceeded more efficiently at a higher draw rate and, hence, at a higher draw stress. Furthermore, for the drawing at a constant draw rate, the transformation proceeded with DR most efficiently for the tensile draw at a T_d around 140 °C, although the draw stress increased with decreasing the T_d. The present result combined with the previous finding in the drawing of PLLA by solid-state extrusion [Macromolecules 36 (2003) 3601] suggests that there is a T_d of around 140 °C at which the crystal transformation proceeds most efficiently with DR, suggesting that there are two factors that have opposite effects on the efficiency of the crystal transformation with increasing the T_d. However, as a result of the combined effects of the T_d and DR on the crystal transformation and the ductility increase with the T_d, an oriented film consisting predominantly of β crystals was obtained by tensile drawing at a T_d in the range of 140-170 °C to the highest DR achieved at each T_d.     

Compatibilizing capability of poly(β-hydroxybutyrate-,co-ε-caprolactone) in the blend of poly(β-hydroxybutyrate) and poly(ε-caprolactone)

In order to increase the miscibility in the blend of poly(β-hydroxybutyrate) [PHB] and poly(ε-caprolactone) [PCL], PHB/PCL copolyesters were used as compatibilizers. These PHB/PCL copolyesters were synthesized by transesterification in solution phase. The melting point [T_m] depression, which was not observed in PHB/PCL blend without compatibilizer, was observed when PHB/PCL copolyesters as compatibilizers were added to the PHB/PCL blend system. As the amount of compatibilizer added to the blend increased, the crystallization temperature [T_c] of PCL in the blend increased and T_c of PHB in the blend decreased. The difference in T_c between PHB and PCL was gradually reduced. When the sequence length of PHB block and PCL block in the PHB/PCL copolyester increased, the miscibility of the blend increased. This is evidenced by the depression in the T_m of PHB and PCL in the blend and by the decrease in the difference of T_c between PHB and PCL. From the polarizing optical micrographs, the phase separation in PHB/PCL blend was observed. However, in the presence of PHB/PCL copolyester, the spherulite of PHB grows in equilibrium with one phase melt. Received: 27 July 1998/Revised version: 12 October 1998/Accepted: 4 November 1998     

Crystallization and morphology of poly(ethylene succinate) and poly(β-hydroxybutyrate) blends

Summary The melting and crystallization behavior of poly(β-hydroxybutyrate) (PHB) and poly(ethylene succinate) blends has been studied by differential scanning calorimetry and optical microscopy. The results indicate that PHB and PES are miscible in the melt. Consequently the blend exhibits a depression of the melting temperature of both PHB and PES. In addition, a depression of the equilibrium melting temperature of PHB is observed. The Flory-Huggins interaction parameter (χ₁₂ ), obtained from melting point depression data, is composition dependent, and its value is always negative. Isothermal crystallization in the miscible blend system PES/PHB is examined by polarized optical microscope. The presence of the PES component gives a wide variety of morphologies. The spherulites exhibit a banded structure and the band spacing decreases with increase PES content. Received: 29 June 1998/Revised version: 31 August 1998/Accepted: 10 September 1998     

Rheological properties of poly(ε-caprolactone) and poly(styrene-co-acrylonitrile) blends

Summary Rheological properties of poly(-caprolactone) (PCL) and Poly (styrene-co-acrylonitrile) (SAN) blends were examined as a function of the acrylonitrile (AN) content in SAN, to systematically understand the correlation between the interaction parameter and the theological properties of miscible polymer blends. When the plateau modulus (G _N ⁰) and zero shear viscosity ( ₀) of the PCL/SAN blends are plotted against the AN content in SAN, a minimum is observed. Qualitatively, the results obtained parallel the variation of the interchain interaction with the AN content. The negative deviation ofG _N ⁰ and ₀ from linearity seems to be attributed to the increase in the entanglement molecular weight between dissimilar chains which results from the chain extension caused by interchain interaction.     

Effect of poly(ε-caprolactone) and titanium (IV) dioxide content on the UV and hydrolytic degradation of poly(lactic acid)/poly(ε-caprolactone) blends

The effect of accelerated weathering degradation on the properties of poly(lactic acid) (PLA)/poly(ε-caprolactone) (PCL) blends and PLA/PCL/titanium (IV) dioxide (TiO₂) nanocomposites are presented in this paper. The results show that both polymers are susceptible to weathering degradation, but their degradation rates are different and are also influenced by the presence of TiO₂ in the samples. Visual, microscopic and atomic force microsocpy observations of the surface after accelerated weathering tests confirmed that degradation occurred faster in the PLA/PCL blends than in the PLA/PCL/TiO₂ nanocomposites. The X-ray diffraction results showed the degradation of PCL in the disappearance of its characteristic peaks over weathering time, and also confirmed that PLA lost its amorphous character and developed crystals from the shorter chains formed as a result of degradative chain scission. It was further observed that the presence of TiO₂ retarded the degradation of both PLA and PCL. These results were supported by the differential scanning calorimetry results. The thermogravimetric analysis results confirmed that that PLA and PCL respectively influenced each other's thermal degradation, and that TiO₂ played a role in the thermal degradation of both PLA and PCL. The tensile properties of both PLA/PCL and PLA/PCL/TiO₂ were significantly reduced through weathering exposure and the incorporation of TiO₂.     

Synthesis of cyclic poly(methyl methacrylate) by the intramolecular cyclization of α-amino, ω-carboxyl heterodifunctional poly(methyl methacrylate)

Summary α-Amino, ω-carboxyl heterodifunctional poly(methyl methacrylate) was prepared by a living anionic polymerization of methyl methacrylate using N,N'-diphenylethylenediamine monolithium amide and succinic anhydride as an initiator and terminator, respectively. Its intramolecular cyclization was carried out to obtain a well-defined cyclic poly(methyl methacrylate). Received: 27 June 2001/Accepted: 16 July 2001     

Preparation of poly(methyl methacrylate) macromonomer by radical polymerization in the presence of methyl α-(bromomethyl)acrylate and copolymerization of the resultant macromonomer

Radical polymerization of methyl methacrylate (MMA) in the presence of methyl -(bromomethyl) acrylate yielded poly-(MMA) bearing the 2-methoxycarbonylallyl end group through chain reaction involving bimol ecular termination. The molecular weight of the resultant polymer was effectively controlled with a small amount of the bromomethylacrylate added; the chain transfer constant was estimated to be 0.9. The poly (MMA) with the unsaturated end group (

Effect of immobilization of poly(γ-glutamic acid) on the biocompatibility of electrospun poly (L-lactide) mats

In this study, poly(L-lactide) (PLLA) non-woven mats were prepared by electrospinning technique, followed by treating with oxygen plasma and grafting with 3-aminopropyl triethoxysilane (APTES), then immersed in poly(γ-glutamic acid) (γ-PGA) solution to form a layer of γ-PGA on the surface. In so doing, hydrophobic PLLA would become highly hydrophilic. Through characterization of hydrophilicity and biocompatibility, the feasibility of these modified mats for wound dressing was evaluated. The results show that after the grafting of γ-PGA, the swelling ratio increased greatly from 7% for pristine PLLA mat to 321% for γ-PGA-grafted PLLA mat, and the contact angle decreased from 112° to 25°. In vitro cytocompatibility tests against L929 fibroblast show that γ-PGA-grafted PLLA was non-cytotoxic. In addition, the proliferation of fibroblasts was higher on γ-PGA-grafted PLLA than on pristine PLLA.     

Impact of organoclays on the phase morphology and the compatibilization efficiency of immiscible poly(ethylene terephthalate)/poly(ε-caprolactone) blends

Adding nanofillers Cloisite 30B (C30B) and Cloisite 15A (C15A) to poly(ethylene terephthalate) (PET)/poly(ε-caprolactone) (PCL) (70/30, wt/wt) blends via melt blending can improve their phase morphology and change their interface properties. The effects of the different selective localization of clay on the structure and the morphologies are studied and evaluated by theoretical and experimental methods. It is found that C30B is selectively localized in PET and at the PET-PCL interface, whereas C15A is mainly localized at the interface. Moreover, the changes in the rheological behavior of the blends are attributed to the formation of clay network-like structures. X-ray diffraction, scanning electron microscope, and transmission electron micrograph observations also evidenced an exfoliated and/or intercalated structure of C30B, and intercalated structure of C15A in the blend, together with significant morphology changes of the initially immiscible blend. The relative permeability to PET/PCL of the nanocomposites decreased with the increasing of nanoclays content. © 2020 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48812.     

A spectroscopic analysis of conformational distortion in the α′ phase of poly(lactic acid)

Simulations in conjunction with Raman scattering were performed to determine the conformational distortion of the α′ form of poly(lactic acid) (PLA). Based on packing constraints of an overall helical structure, the chain conformation can only be approximated by slight deviations from a tg’t chain conformation. Models were generated with different types of random departures from the expected dihedral angles. Raman active vibrations in the 700 cm⁻¹ region that are sensitive to changes in chain conformation were analyzed. The model that showed the best fit to the experimental data contains a majority (80%) of tg’t-10₃ sequences with randomly distributed tg’t-3₁ units. Departure of the O-C_α dihedral angle was also proved. The mechanism of order formation was established. As PLA chains crystallize at low temperatures, only the α′ phase with a disordered helix can be formed which at elevated temperatures can transform to the more ordered α phase. The conformation distortion is then due to the inability for some chains to complete the transition to 10₃ helicity, thus resulting in the formation of the distorted α′ structure.