Role of active oxygen transients in selective catalytic reduction of N2O with CH4 over Fe-zeolite catalysts

Sharp NO and O₂ desorption peaks, which were caused by the decomposition of nitro and nitrate species over Fe species, were observed in the range of 520–673 K in temperature-programmed desorption (TPD) from Fe-MFI after H₂ treatment at 773 K or high-temperature (HT) treatment at 1073 K followed by N₂O treatment. The amounts of O₂ and NO desorption were dependent on the pretreatment pressure of N₂O in the H₂ and N₂O treatment. The adsorbed species could be regenerated by the H₂ and N₂O treatment after TPD, and might be considered to be active oxygen species in selective catalytic reduction (SCR) of N₂O with CH₄. However, the reaction rate of CH₄ activation by the adsorbed species formed after the H₂ and N₂O or the HT and N₂O treatment was not so high as that of the CH₄ + N₂O reaction over the catalyst after O₂ treatment. The simultaneous presence of CH₄ and N₂O is essential for the high activity of the reaction, which suggests that nascent oxygen species formed by N₂O dissociation can activate CH₄ in the SCR of N₂O with CH₄.     

Catalytic reduction of N2O over steam-activated FeZSM-5 zeolite: Comparison of CH4, CO, and their mixtures as reductants with or without excess O2

The catalytic reduction of N₂O by CH₄, CO, and their mixtures has been comparatively investigated over steam-activated FeZSM-5 zeolite. The influence of the molar feed ratio between N₂O and the reducing agents, the gas-hourly space velocity, and the presence of O₂ on the catalytic performance were studied in the temperature range of 475–850 K. The CH₄ is more efficient than CO for N₂O reduction, achieving the same degree of conversion at significantly lower temperatures. The apparent activation energy for N₂O reduction by CH₄ was very similar to that of direct N₂O decomposition (140 kJ mol⁻¹), being much lower for the N₂O reduction by CO (60 kJ mol⁻¹). This suggests that the reactions have a markedly different mechanism. Addition of CO using equimolar mixtures in the ternary N₂O + CH₄ + CO system did not affect the N₂O conversion with respect to the binary N₂O + CH₄ system, indicating that CO does not interfere in the low-temperature reduction of N₂O by CH₄. In the ternary system, CO contributed to N₂O reduction when methane was the limiting reactant. The conversion and selectivity of the reactions of N₂O with CH₄, CO, and their mixtures were not altered upon adding excess O₂ in the feed.     

Catalytic decomposition of N2O and catalytic reduction of N2O and N2O + NO by NH3 in the presence of O2 over Fe-zeolite

The decomposition of N₂O, and the catalytic reduction by NH₃ of N₂O and N₂O + NO, have been studied on Fe-BEA, -ZSM-5 and -FER catalysts. These catalysts were prepared by classical ion exchange and characterized by TPR after various activation treatments. Fe-FER is the most active material in the catalytic decomposition because “oxo-species” reducible at low temperature, appearing upon interaction of Fe^II-zeolite with N₂O (-oxygen), are formed in largest amounts with this material. The decomposition of N₂O is promoted by addition of NH₃, and even more with NH₃ + NO in the case of Fe-FER and -BEA. It is proposed that the NO-promoted reduction of N₂O originated from the fast surface reaction between -oxygen O^* and NO^* to yield NO₂^*, which in turn reacts immediately with NH₃.     

Decomposition of nitric oxide over perovskite oxide catalysts: effect of CO2, H2O and CH4

Direct nitric oxide decomposition over perovskites is fairly slow and complex, its mechanism changing dramatically with temperature. Previous kinetic study for three representative compositions (La_0.87Sr_0.13Mn_0.2Ni_0.8O_3−δ, La_0.66Sr_0.34Ni_0.3Co_0.7O_3−δ and La_0.8Sr_0.2Cu_0.15Fe_0.85O_3−δ) has shown that depending on the temperature range, the inhibition effect of oxygen either increases or decreases with temperature. This paper deals with the effect of CO₂, H₂O and CH₄ on the nitric oxide decomposition over the same perovskites studied at a steady-state in a plug-flow reactor with 1 g catalyst and total flowrates of 50 or 100 ml/min of 2 or 5% NO. The effect of carbon dioxide (0.5–10%) was evaluated between 873 and 923 K, whereas that of H₂O vapor (1.6 or 2.5%) from 723 to 923 K. Both CO₂ and H₂O inhibit the NO decomposition, but inhibition by CO₂ is considerably stronger. For all three catalysts, these effects increase with temperature. Kinetic parameters for the inhibiting effects of CO₂ and H₂O over the three perovskites were determined. Addition of methane to the feed (NO/CH₄=4) increases conversion of NO to N₂ about two to four times, depending on the initial NO concentration and on temperature. This, however, is still much too low for practical applications. Furthermore, the rates of methane oxidation by nitric oxide over perovskites are substantially slower than those of methane oxidation by oxygen. Thus, perovskites do not seem to be suitable for catalytic selective NO reduction with methane.     

Catalytic decomposition of nitrous oxide over Ru-exchanged zeolites

We report that ultrastable faujasite-based ruthenium zeolites are highly active catalysts for N₂O decomposition at low temperature (120–200°C). The faujasite-based ruthenium catalysts showed activity for the decomposition of N₂O per Ru³⁺ cation equivalent to the ZSM-5 based ruthenium catalysts at much lower temperatures (TOF at 0.05 vol.-% N₂O: 5.132 × 10⁻⁴ s⁻¹ Ru⁻¹ of Ru-HNaUSY at 200°C versus 5.609 × 10⁻⁴ s⁻¹ Ru⁻¹ of Ru-NaZSM-5 at 300°C). The kinetics of decomposition of N₂O over a Ru-NaZSM-5 (Ru: 0.99 wt.-%), a Ru-HNaUSY (Ru: 1.45 wt.-%) and a Ru-free, Na-ZSM-5 catalyst were studied over the temperature range from 40 to 700°C using a temperature-programmed micro-reactor system. With partial pressures of N₂O and O₂ up to 0.5 vol.-% and 5 vol.-%, respectively, the decomposition rate data are represented by: −dN₂O/dt=itk(P_N2O) (P_O2)^−0.5 for Ru-HNaUSY, −dN₂O/dt=k(P_N2O) (P_O2)^−0.1 for Ru-NaZSM-5, and −dN₂O/dt=k(P_N2O)^−0.2 (P_O2)^−0.1 for Na-ZSM-5. Oxygen had a stronger inhibition effect on the Ru-HNaUSY catalyst than on Ru-NaZSM-5. The oxygen inhibition effect was more pronounced at low temperature than at high temperature. We propose that the negative effect of oxygen on the rate of N₂O decomposition over Ru-HNaUSY is stronger than Ru-NaZSM-5 because at the lower temperatures (<200°C) the desorption of oxygen is a rate-limiting step over the faujasite-based catalyst. The apparent activation energy for N₂O decomposition in the absence of oxygen is much lower on Ru-HNaUSY (E_a: 46 kJ mol⁻¹) than on Ru-NaZSM-5 (E_a: 220 kJ mol⁻¹).     

NO removal by CH4 on Co-NaX-CO and Ag-NaX catalysts in a dual-bed system

NO removal using CH₄ as a reductant in a dual-bed system has been investigated with Co-NaX and Ag-NaX catalysts, which were prepared by Co²⁺-, Ag⁺-ion exchange into zeolite NaX, respectively, and activation for 5 h at 500 °C. The experimental result has been compared with that of a Co-NaX-CO catalyst, additionally pre-treated under CO flow for the Co-NaX catalyst. The cobalt crystal structure of a Co-NaX-CO catalyst is Co₃O₄, which promotes NO oxidation to NO₂ by excess O₂ at a low temperature (523 K). The mechanical mixture of Co-NaX-CO and Ag-NaX catalysts shows a synergy effect on NO reduction to N₂ by CH₄ in the presence of excess O₂ and H₂O, but the NO reduction decreases quickly as time passes. However, the NO reduction to N₂ in a deNO bed at 523 K and a deNO₂ bed at 423 K, which are relatively lower than the reaction temperatures for common SCR systems, still remained at 67% even in a H₂O 10% gas mixture after 160 min.     

Catalytic decomposition of N2O over CeO2 promoted Co3O4 spinel catalyst

A series of CeO₂ promoted cobalt spinel catalysts were prepared by the co-precipitation method and tested for the decomposition of nitrous oxide (N₂O). Addition of CeO₂ to Co₃O₄ led to an improvement in the catalytic activity for N₂O decomposition. The catalyst was most active when the molar ratio of Ce/Co was around 0.05. Complete N₂O conversion could be attained over the CoCe0.05 catalyst below 400 °C even in the presence of O₂, H₂O or NO. Methods of XRD, FE-SEM, BET, XPS, H₂-TPR and O₂-TPD were used to characterize these catalysts. The analytical results indicated that the addition of CeO₂ could increase the surface area of Co₃O₄, and then improve the reduction of Co³⁺ to Co²⁺ by facilitating the desorption of adsorbed oxygen species, which is the rate-determining step of the N₂O decomposition over cobalt spinel catalyst. We conclude that these effects, caused by the addition of CeO₂, are responsible for the enhancement of catalytic activity of Co₃O₄.     

Kinetic studies of CH4 oxidation over Pt–NiO/δ-Al2O3 in a fluidised bed reactor

The oxidation of CH₄ over Pt–NiO/δ-Al₂O₃ has been studied in a fluidised bed reactor as part of a major project on an autothermal (combined oxidation–steam reforming) system for CH₄ conversion. The kinetic data were collected between 773 and 893 K and 101 kPa total pressure using CH₄ and O₂ compositions of 10–35% and 8–30%, respectively. Rate–temperature data were also obtained over alumina-supported monometallic catalysts, Pt and NiO. The bimetallic Pt–NiO system has a lower activation energy (80.8 kJ mol⁻¹) than either Pt (86.45 kJ mol⁻¹) and NiO (103.73 kJ mol⁻¹). The superior performance of the bimetallic catalyst was attributed to chemical synergy. The reaction rate over the Pt–NiO catalyst increased monotonically with CH₄ partial pressure but was inhibited by O₂. At low partial pressures (<30 kPa), H₂O has a detrimental effect on CH₄ conversion, whilst above 30 kPa, the rate increased dramatically with water content.     

Effect of Pt on the water resistance of Co-zeolites upon the SCR of NOx with CH4

The objective of this work was to study the promotional effect of Pt on Co-zeolite (viz. mordenite, ferrierite, ZSM-5 and Y-zeolite) and Co/Al₂O₃ on the selective catalytic reduction (SCR) of NO_x with CH₄ under dry and wet reaction stream. After being reduced in H₂ at 350°C, the PtCo bimetallic zeolites showed higher NO to N₂ conversion and selectivity than the monometallic samples, as well as a combination of the latter samples such as mechanical mixtures or two-stage catalysts. After the same pretreatment, under wet reaction stream, the bimetallic samples were also more active. Among the other catalysts studied with 5% of water in the feed, (NO = CH₄ = 1000 ppm, O₂ = 2%), the NO conversion dropped to zero over Co_2.0Mor at 500°C and GHSV = 30,000 h⁻¹, whereas it is 20% in Pt_0.5Co_2.0Mor. In Pt/Co/Al₂O₃ the NO_x conversion dropped below 5% with only 2% of water under the same reaction conditions. The specific activity given as molecules of NO converted per total metal atom per second were 16.5 × 10⁻⁴ s⁻¹ for Pt_0.5Co_2.0Fer, 13 × 10⁻⁴ s⁻¹ for Pt_0.5Co_2.0Mor, 4.33 × 10⁻⁴ s⁻¹ for Pt_0.5Co_2.0ZSM-5 and 0.5 × 10⁻⁴ s⁻¹ for Pt/Co/Al₂O₃. The Y-zeolite-based samples were inactive in both mono and bimetallic samples. The species initially present in the solid were Pt° and Co°, together with Co²⁺ and Pt²⁺ at exchange positions. Co° seems not to participate as an active site in the SCR of NO_x. Those species remained after the reaction but some reorganization occurred. A synergetic effect among the different species that enhances both the NO to NO₂ reaction, the activation of CH₄ and also the ability of the catalyst to adsorb NO, could be responsible for the high activity and selectivity of the bimetallic zeolites.     

The effect of oxygen concentration on the reduction of NO with propylene over CuO/γ-Al2O3

The effect of oxygen concentration on the pulse and steady-state selective catalytic reduction (SCR) of NO with C₃H₆ over CuO/γ-Al₂O₃ has been studied by infrared spectroscopy (IR) coupled with mass spectroscopy studies. IR studies revealed that the pulse SCR occurred via (i) the oxidation of Cu⁰/Cu⁺ to Cu²⁺ by NO and O₂, (ii) the co-adsorption of NO/NO₂/O₂ to produce Cu²⁺(NO₃⁻)₂, and (iii) the reaction of Cu²⁺(NO₃⁻)₂ with C₃H₆ to produce N₂, CO₂, and H₂O. Increasing the O₂/NO ratio from 25.0 to 83.4 promotes the formation of NO₂ from gas phase oxidation of NO, resulting in a reactant mixture of NO/NO₂/O₂. This reactant mixture allows the formation of Cu²⁺(NO₃⁻)₂ and its reaction with the C₃H₆ to occur at a higher rate with a higher selectivity toward N₂ than the low O₂/NO flow. Both the high and low O₂/NO steady-state SCR reactions follow the same pathway, proceeding via adsorbed C₃H₇---NO₂, C₃H₇---ONO, CH₃COO⁻, Cu⁰---CN, and Cu⁺---NCO intermediates toward N₂, CO₂, and H₂O products. High O₂ concentration in the high O₂/NO SCR accelerates both the formation and destruction of adsorbates, resulting in their intensities similar to the low O₂/NO SCR at 523–698 K. High O₂ concentration in the reactant mixture resulted in a higher rate of destruction of the intermediates than low O₂ concentration at temperatures above 723 K.     

Effects of methane and oxygen on decomposition of nitrous oxide over metal oxide catalysts

Catalytic activities of various metal oxides for decomposition of nitrous oxide were compared in the presence and absence of methane and oxygen, and the general rule in the effects of the coexisting gases was discussed. The reaction rates of nitrous oxide were well correlated to the heat of formation of metal oxide, i.e., a V-shaped relationship with a minimum at −ΔH_f⁰ around 450 kJ (O mol)⁻¹ was observed in N₂O decomposition in an inert gas. In the case of metal oxides having the heat of formation lower than 450 kJ (O mol)⁻¹, CuO, Co₃O₄, NiO, Fe₂O₃, SnO₂, In₂O₃, Cr₂O₃, the activities were strongly affected by the presence of methane and oxygen. On the other hand, the activities of TiO₂, Al₂O₃, La₂O₃, MgO and CaO were almost independent. The reaction rate of nitrous oxide was significantly enhanced by methane. The promotion effect of methane was attributed to the reduction of nitrous oxide with methane: 4N₂O+CH₄→2N₂+CO₂+2H₂O. The activity was suppressed in the presence of oxygen on the metal oxides having lower heat of formation. On the basis of Langmuir–Hinshelwood mechanism, the effect of oxygen on nitrous oxide decomposition was rationalized with the strength of metal–oxygen bond.     

NO reduction by CH4 in the presence of O2 over La2O3 supported on Al2O3

Dispersing La₂O₃ on δ- or γ-Al₂O₃ significantly enhances the rate of NO reduction by CH₄ in 1% O₂, compared to unsupported La₂O₃. Typically, no bend-over in activity occurs between 500° and 700°C, and the rate at 700°C is 60% higher than that with a Co/ZSM-5 catalyst. The final activity was dependent upon the La₂O₃ precursor used, the pretreatment, and the La₂O₃ loading. The most active family of catalysts consisted of La₂O₃ on γ-Al₂O₃ prepared with lanthanum acetate and calcined at 750°C for 10 h. A maximum in rate (mol/s/g) and specific activity (mol/s/m²) occurred between the addition of one and two theoretical monolayers of La₂O₃ on the γ-Al₂O₃ surface. The best catalyst, 40% La₂O₃/γ-Al₂O₃, had a turnover frequency at 700°C of 0.05 s⁻¹, based on NO chemisorption at 25°C, which was 15 times higher than that for Co/ZSM-5. These La₂O₃/Al₂O₃ catalysts exhibited stable activity under high conversion conditions as well as high CH₄ selectivity (CH₄ + NO vs. CH₄ + O₂). The addition of Sr to a 20% La₂O₃/γ-Al₂O₃ sample increased activity, and a maximum rate enhancement of 45% was obtained at a SrO loading of 5%. In contrast, addition of SO⁼₄ to the latter Sr-promoted La₂O₃/Al₂O₃ catalyst decreased activity although sulfate increased the activity of Sr-promoted La₂O₃. Dispersing La₂O₃ on SiO₂ produced catalysts with extremely low specific activities, and rates were even lower than with pure La₂O₃. This is presumably due to water sensitivity and silicate formation. The La₂O₃/Al₂O₃ catalysts are anticipated to show sufficient hydrothermal stability to allow their use in certain high-temperature applications.     

Catalytic reduction of NOx with H2/CO/CH4 over PdMOR catalysts

Conversion of NO_x with reducing agents H₂, CO and CH₄, with and without O₂, H₂O, and CO₂ were studied with catalysts based on MOR zeolite loaded with palladium and cerium. The catalysts reached high NO_x to N₂ conversion with H₂ and CO (>90% conversion and N₂ selectivity) range under lean conditions. The formation of N₂O is absent in the presence of both H₂ and CO together with oxygen in the feed, which will be the case in lean engine exhaust. PdMOR shows synergic co-operation between H₂ and CO at 450–500 K. The positive effect of cerium is significant in the case of H₂ and CH₄ reducing agent but is less obvious with H₂/CO mixture and under lean conditions. Cerium lowers the reducibility of Pd species in the zeolite micropores. The catalysts showed excellent stability at temperatures up to 673 K in a feed with 2500 ppm CH₄, 500 ppm NO, 5% O₂, 10% H₂O (0–1% H₂), N₂ balance but deactivation is noticed at higher temperatures. Combining results of the present study with those of previous studies it shows that the PdMOR-based catalysts are good catalysts for NO_x reduction with H₂, CO, hydrocarbons, alcohols and aldehydes under lean conditions at temperatures up to 673 K.     

Mechanistic peculiarities of the N2O reduction by CH4 over Fe-silicalite

Transient isotopic studies in the temporal analysis of products (TAP) reactor evidenced the importance of the lifetime of oxygen species generated upon N₂O decomposition on extraframework iron sites of Fe-silicalite for methane oxidation at 723 K. Fe-silicalite effectively activates CH₄ when N₂O and CH₄ are pulsed together in the reactor. However, these oxygen species gradually become inactive for methane oxidation as the time delay between the N₂O and CH₄ pulses is increased from 0 to 2 s.     

Kinetic analysis of N2O decomposition over calcined hydrotalcites

Kinetics of N₂O decomposition over catalyst prepared by calcination of Co–Mn hydrotalcite was examined in integral fixed-bed reactor () at various N₂O and O₂ initial partial pressure at temperature range of 330–450 °C. Kinetic data were evaluated by linear and non-linear regression method, 15 kinetic expressions were tested. Based on the obtained results a redox model of N₂O decomposition was proposed. At low pressures of O₂, adsorbed oxygen is formed by the N₂O decomposition; the N₂O chemisorption is considered as the rate-determining step. On the contrary, at high O₂ pressure it could be assumed that adsorbed oxygen species appear as a result of O₂ adsorption and the Eley–Rideal mechanism is the rate determining. N₂O decomposition is well described by the 1st rate law at N₂O and O₂ concentrations typical for waste gases.     

N2O catalytic decomposition over various spinel-type oxides

Various spinel-type catalysts AB₂O₄ (where A = Mg, Ca, Mn, Co, Ni, Cu, Cr, Fe, Zn and B = Cr, Fe, Co) were prepared and characterized by XRD, BET, TEM and FESEM-EDS. The performance of these catalysts towards the decomposition of N₂O to N₂ and O₂ was evaluated in a temperature programmed reaction (TPR) apparatus in the absence and the presence of oxygen. Spinel-type oxides containing Co at the B site were found to provide the best activity. The half conversion temperature of nitrous oxide over the MgCo₂O₄ catalyst was 440 °C and 470 °C in the absence and presence of oxygen, respectively (GHSV = 80,000 h⁻¹).

On the grounds of temperature programmed oxygen desorption (TPD) analyses as well as of reactive runs, the prevalent activity of the MgCo₂O₄ catalyst could be explained by its higher concentration of suprafacial, weakly chemisorbed oxygen species, whose related vacancies contribute actively to nitrous oxide catalytic decomposition. This indicates the way for the development of new, more active catalysts, possibly capable of delivering at low temperatures amounts of these oxygen species even higher than those characteristic of MgCo₂O₄.     

Kinetic measurements of CH4 combustion over a 10% PdO/ZrO2 catalyst using an annular flow microreactor

A kinetic study on CH₄ combustion over a PdO/ZrO₂ (10%, w/w) catalyst has been performed in a temperature range between 400 and 550 °C by means of an annular catalytic microreactor.

The role of mass transfer phenomena including diffusion in the catalyst pore, gas–solid diffusion and axial diffusion in the gas phase, has been preliminary addressed by means of mathematical modeling. Simulation results have pointed out the key role of internal diffusion showing that thicknesses of the active catalyst layer as thin as 10–15 μm are required to minimize the impact of mass transfer limitations. The thermal behavior of the reactor has been also addressed by means of catalytic combustion tests with CH₄ and CO–H₂ mixtures as fuels. The results have demonstrated the possibility to obtain nearly isothermal temperature profiles under severe conditions (up to 3% of CH₄) thanks to effective dissipation of reaction heat by radiation from the catalyst outer skin.

Finally the effect of reactants (CH₄ and O₂) and products (H₂O and CO₂) on CH₄ combustion rate has been addressed. The results have shown that both H₂O and CO₂ markedly inhibit the reaction up to 550 °C. The data have been fitted by the following simple power law expression r=k_rP_CH4P_H2O^−0.32P_CO2^−0.25 with an apparent activation energy of 108 kJ/mol.

Evidences have been found and discussed indicating a key role of the support on the extent of such inhibition effects.     

Decomposition of nitrous oxide over supported rhodium catalysts and dependency on feed gas composition

The catalytic decomposition of nitrous oxide to nitrogen and oxygen was studied overRh/ZnO, Rh/CeO₂, Rh/ZSM-5, CuZSM-5 and CoAlCO₃HT (hydrotalcite). The effects of metal loading and calcination conditions upon the catalytic performance were examined on Rh/ZnO. A 0.5 wt.% Rh/ZnO catalyst was found to be the most active catalyst, whose reaction rate was 4.0 × 10⁴ μmol(N₂O) · g⁻¹ · h⁻¹ under the conditions of 950 ppm N₂O and 5% O₂ at 300°C. The oxidized Rh/ZnO showed a higher activity than that calcined in a reducing atmosphere. The TEM and EDX observations revealed the formation of particles of ca. 50Åin diameter. They consisted of rhodium and zinc oxides as major and minor components, respectively. The activities of all these catalysts decreased when NO₂ and H₂O were added to the feed.     

Catalytic decomposition of nitrous oxide N 2O: a study for p-block-element lead in PbO—ZrO2/Al2O3 systems

PbO—ZrO₂ catalysts have been prepared by sequential impregnation/calcination onto Al₂O₃ support for high concentration N₂O (27.97 mol%) decomposition. The p-block-element involved material system has been investigated with GC, BET, DTA, XRD and catalytic activity evaluation. It is found that with an atomic ratio Pb:Zr = 1:6 the material system shows the best catalytic performance for the decomposition. The catalyst with this composition has a tetragonal phase of ZrO₂ over reaction temperatures. The catalytic activity observed can be attributed to the presence of Pb cations with mixed valence states in tetragonal ZrO₂ lattice. Doping gases such as H₂O, CO₂, and O₂ are also mixed into the N₂O and studied. It is found that N₂O adsorption is rate-limiting step for the decomposition reaction. The reaction can be described as first order with respect to partial pressure of N₂O, considering that decomposition product O₂ exhibits no inhibition effect on the reaction in high conversion region.