Film thickness dependence of microstructures and magnetic properties in single-layered FePt films by in-situ annealing

The FePt films with various thicknesses (t) of 5 to 50 nm are deposited on Si(100) substrate without any underlayer by in-situ annealing at substrate temperature (Ts) of 620 °C. A strong (001) texture of L1₀ FePt film is obtained and presents high perpendicular magnetic anisotropy as the film thickness increases to 30 nm. By further increasing the thickness to exceed 30 nm, the (111) orientation of L1₀ FePt is enhanced greatly, indicating that the quality of perpendicular magnetic anisotropy degrades when the thickness of the FePt film is greater than 30 nm. The single-layered FePt film with thickness of 30 nm by in-situ depositing at 620 °C shows good perpendicular magnetic properties (perpendicular coercivity of 1033 kA/m (13 kOe), saturation magnetization of 1.08 webers/m² and perpendicular squareness of 0.91, respectively), which reveal its significant potential for perpendicular magnetic recording media.     

Low temperature ordering of FePt films by in-situ heating deposition plus post deposition annealing

FePt thin films with 40 nm thickness were prepared on thermally oxidized Si (001) substrates by dc magnetron sputtering at the nominal growth temperature 375 °C. The effects of annealing on microstructure and magnetic properties of FePt thin films were investigated. The as-deposited FePt thin films show soft magnetic properties. After the as-deposited FePt thin films were annealed at various temperatures and furnace cooled, it is found that the ordering temperature of L1₀ FePt phase could be reduced to 350 °C. For FePt thin films annealed at 350 °C, the in-plane and out-of-plane coercivities of the films increased to 510 and 543 kA/m, respectively, and the films had hard magnetic properties. A highly (001) orientation was obtained, when FePt thin films were annealed at 600 °C. And the hysteresis loops of FePt thin films annealed at 600 °C show out-of-plane magnetic anisotropy.     

Microstructure and magnetic properties of the FePt film on a membrane of anodized aluminum oxide

By making use of the dc magnetron sputtering system, the Au/FePt bilayers have been prepared on glass substrates and anodized aluminum oxide (AAO) membranes with an average pore diameter of around 200 nm. In both cases, the FePt films can be converted into the magnetically hard phase, namely L1₀ phase, after a heat treatment above 500 °C for 1 h. A nanoparticle-like structure can be observed in the 15-nm-thick FePt film on the AAO membrane. The experimental observations of the structure and the magnetism of the FePt films on the AAO membranes are firstly established.     

Effect of AlN layer thickness on structure and magnetic properties of FePt/AlN multilayers

FePt (50 nm) and [FePt(xnm)/AlN(1, 2, 3 nm)]₁₀ (x=2, 3 nm) films were prepared by RF magnetron sputtering technique, then were annealed at 550 °C for 30 min. This work investigates the effect of AlN layer thickness on structure and magnetic properties of FePt/AlN multilayers. Superlattice (0 0 1) peaks can be found in the grazing incidence X-ray diffraction of FePt and [FePt (3 nm)/AlN (1, 2, 3 nm)]₁₀ films, which indicate that the FCC phase has been partially transformed into ordered L1₀ phase. Compared with the single layer FePt film, superlattice (0 0 1) peaks of FePt/AlN multilayers are weak and wide, which indicates that the introducing of AlN hinders the growth of FePt particle, and also shows the introducing of AlN is not beneficial to the transformation from FCC phase to L1₀ phase. In addition, the low-angle XRD spectra show the layered structure of FePt/AlN has been broken after annealing. The coercivities, particle size, intergrain exchange interactions of FePt/AlN films are decreased with increasing AlN layer thickness.     

FePt纳米薄膜研究进展

由于FePt在超高密度磁存储材料方面的广阔应用前景及其局限性,研究人员对FePT薄膜进行了大量的研究及改性.根据国外近期在此领域的研究现状,综述了单相、复相及掺杂FePt薄膜的制备以及对结构和性质的影响.复相或掺杂主要是通过结构的改变来降低L10晶相转变温度和FePt颗粒的大小,通过其耦合作用来影响FePt薄膜的磁学性能,使其成为超高密度存储器材料.     

The effect of thickness on the texture and magnetic properties of single-layered FePt films by rapid thermal annealing

The single-layered FePt films with thickness in the range of 5 to 50 nm are deposited directly on Si(100) substrate without underlayer, then post annealed at 700 degrees C by rapid thermal annealing (RTA) technique. As the film thickness of FePt is over 20 nm, the L1(0) FePt(111) preferred orientation is presented and tended to in-plane magnetic anisotropy. However, the L1(0) FePt(001) texture is obtained and exhibited perpendicular magnetic anisotropy as the film thickness is decreased to 10 nm. Its perpendicular coercivity (Hc(perpendicular)), saturation magnetization (Ms) and perpendicular squareness (S(perpendicular)) are 14.8 kOe, 795 emu/cm3 and 0.79, respectively. On the other hand, both the grain size and domain size of FePt film decrease with decreasing the film thickness of FePt. The grain size for 10-nm FePt film is as small as 9.7 nm with domain size of 123 nm, which reveal its significant potential as perpendicular magnetic recording media for ultra high-density recording.     

Coercivity variation in exchange-coupled Fe/FePt bilayer with perpendicular magnetization

The soft/hard Fe/FePt film with perpendicular magnetization has been deposited on a glass substrate. The (001) oriented L1₀ FePt film was obtained when annealed by rapid thermal process at 800 °C and a Fe layer was deposited at room temperature with thicknesses of 2 nm to 20 nm. Controlling the Fe layer thickness allowed modification of the hysteresis loops from out-of-plane rigid magnet to in-plane exchange-spring like magnet due to the nanometer scale interface coupling. When the Fe layer thickness increased to 2 nm, the out-of-plane coercivity is reduced to 5.9 kOe but the remanence ratio (0.98) is still high. The Fe (2 nm)/FePt film shows perpendicular magnetization with linear in-plane hysteresis loop. The remanence ratio is reduced to 0.85 when the Fe layer thickness increased to 5 nm. When the Fe layer thickness was varied up to 10-20 nm, the in-plane hysteresis loop shows exchange-spring like behavior with two-step magnetization reversal processes. The films with perpendicular coercivity were moderated by the thickness of soft magnetic layer.     

Thickness dependence of microstructures and magnetic properties for CoPt/Ag nanocomposite thin films

Ag underlayer (30 nm) has improved the degree of ordering and perpendicular magnetic anisotropy of CoPt films (7.5-10 nm). After annealing at 600 °C and 700 °C, the perpendicular coercivity of CoPt/Ag films has been raised as the thicknesses of CoPt layers are increased. The magnetic easy axis of CoPt/Ag films would change from a random orientation to an out-of-plane orientation. It is found that Ag underlayer with thickness of 30 nm can improve the perpendicular magnetic properties of CoPt layers with thicknesses in the range of 7.5-10 nm. The CoPt/Ag films would be a candidate for perpendicular magnetic recording media.     

Effect of carbon additive on microstructure evolution and magnetic properties of epitaxial FePt (001) thin films

FePt:C thin films were deposited on CrRu underlayers by DC magnetron co-sputtering. The effects of C content, FePt:C film thickness and substrate temperature on the microstructural and magnetic properties of the epitaxial FePt (001) films were studied. Experimental results showed that even with 30 vol.% C doping, the FePt films could keep a (001) preferred orientation at 350 °C. When a FePt:C film was very thin (< 5 nm), the film had a continuous microstructure instead of a granual structure with C diffused onto the film surface. With further increased film thickness, the film started to nucleate and formed a column microstructure over continuous FePt films. A strong exchange coupling in the FePt:C films was believed to be due to the presence of a thin continuous FePt layer attributed to the carbon diffusion during the initial stage of the FePt:C film growth. Despite the presence of a strong exchange coupling in the FePt:C (20 vol.% C) film, the SNR ratio of the FePt:C media was about 10 dB better than that of the pure FePt media. The epitaxial growth of the FePt:C films on the Pt layers was observed from high resolution TEM cross sectional images even for the films grown at about 200 °C. The TEM images did not show an obvious change in the morphology of the FePt:C films deposited at different temperatures (from 200 °C to 350 °C), though the ordering degree and coercivity of the films increased with increased substrate temperature.     

Effect of tungsten on the electrochromic behaviour of sol-gel dip coated molybdenum oxide thin films

The paper describes the results obtained on the performance of Mo oxide and mixed W/Mo oxide thin films for possible electrochromic applications. Mo and W/Mo oxide films were deposited on conductive (FTO) glass substrates using sol-gel dip coating method. The films were annealed at 250 °C for 30 min. The structure and morphology of Mo and W/Mo oxide films were examined using XRD, SEM and EDS. XRD results indicate the amorphous nature of the Mo and W/Mo oxide films annealed for 30 min. The CV measurements revealed that the films prepared with 10 wt.% of tungsten exhibit maximum anodic/cathodic diffusion coefficient of 24.99/12.71 × 10⁻¹¹ cm²/s. The same film exhibits a maximum transmittance variation (ΔT%) of 83.4% at 630 nm and 81.06% at 550 nm with the optical density of 1.00 and 1.13 respectively.     

Effects of post-deposition surface treatment on the optical, structural and hydrogen sensing properties of TiO2 thin films

TiO₂ thin films were prepared by DC reactive magnetron sputtering in a mixture of oxygen and argon on glass and oxidized silicon substrates. The effect of post-deposition annealing (300 °C, 500 °C and 700 °C for 8 h in air) on the structural and morphological properties of TiO₂ thin films is presented. In addition, the effect of Pt surface modification (1, 3 and 5 nm) on hydrogen sensing was studied. XRD patterns have shown that in the range of annealing temperatures from 300 °C to 500 °C crystallization starts and the thin film structure changes from amorphous to polycrystalline (anatase phase). In the case of samples on glass substrate, optical transmittance spectra were recorded. TiO₂ thin films were tested as sensors of hydrogen at concentrations 10,000-1000 ppm and operating temperatures within the 180-200 °C range. The samples with 1 nm and in particular with 3 nm of Pt on the surface responded to hydrogen fast and with high sensitivity.     

Growth temperature dependent dielectric properties of BiFeO3 thin films deposited on silica glass substrates

We have studied the dependence of dielectric properties on the deposition temperature of BiFeO₃ thin films grown by the pulsed laser deposition technique. Thin films have been grown onto amorphous silica glass substrates with pre-patterned Au in-plane capacitor structures. It is shown that on the amorphous glass substrate, BiFeO₃ films with a near-bulk permittivity of 26 and coercive field of 80 kV/cm may be grown at a deposition temperature of about 600 °C and 1 Pa oxygen pressure. Low permittivity and higher coercive field of the films grown at the temperatures below and above 600 °C are associated with an increased amount of secondary phases. It is also shown that the deposition of BiFeO₃ at low temperature (i.e. 500 °C) and post deposition ex-situ annealing at elevated temperature (700 °C) increases the permittivity of a film. The applied bias and time dependence of capacitance of the films deposited at 700 °C and ex-situ annealed films are explained by the de-pinning of the ferroelectric domain-walls.     

Influence of magnetic annealing on high-frequency magnetic properties of FeCoNd films

FeCoNd thin film with thickness of 166 nm has been fabricated on silicon (1 1 1) substrates by magnetron co-sputtering and annealed for one hour under magnetic field at different temperatures (T_a) from 200 °C to 700 °C. The As-deposited and annealed FeCoNd film samples at T_a ≤ 500 °C were amorphous while the ones obtained at T_a ≥ 600 °C were crystallized. We found that the perpendicular anisotropy field gradually decreases as the annealing temperature increases from room temperature to 300 °C. A well induced in-plane uniaxial anisotropy is achieved at the annealing temperature between 400 and 600 °C. The variation of the dynamic magnetic properties of annealed FeCoNd films can be well explained by the Landau-Lifshitz equation with the variation of the anisotropy field re-distribution and the damping constant upon magnetic annealing. The magnetic annealing might be a powerful post treatment method for high frequency application of magnetic thin films.     

Optimization of L10-FePt/MgO/CrRu thin films for next-generation magnetic recording media

L1₀-FePt thin films were deposited on silicon substrates with the structure of Si/CrRu/MgO/FePt. The magnetic and microstructural properties were optimized by varying the FePt sputter pressure and temperature, as well as the thicknesses of all three layers. High coercivity films greater than 1.8 T were grown when the FePt sputter pressure was at 1.33 Pa with a thickness of only 4 nm, on CrRu and MgO underlayers as thin as 10 nm and 2 nm, respectively.     

Effects of Os inserted layers on the microstructures and magnetic properties of the FePt films

The microstructure and magnetic properties of multilayer [Os(t)/FePt(x)]n films on a glass substrate with a 10 nm Os buffer layer by ion beam sputtering have been studied as a function of the annealing temperatures between 300 and 800 degrees C. Here, t = 0.2, 1 or 5 nm and x varied from 10, 20, 25, 50, to 100 nm with its associated n value of 10, 5, 4, 2, and 1, respectively. No diffusion evidence was found in samples with a thin Os layer and t > or = 1 nm. The average grain size of the multilayer films can be well controlled by both annealing temperature and thickness of the FePt layer by a very thin Os space layer with t > or = 1 nm. The enhancement of H(c) can be understood from the fact that for a FePt film with an Os spacer layers, the increasing number of Os layer will inhibit the grain growth of FePt grains and enriches the grain boundary. We have experimentally demonstrated that even with a very thin 1 nm Os spacer layers, the [Os(t)/FePt(x)]n multilayer films can exhibit good hard magnetic properties and are attractive candidates for ultrahigh density magnetic recording media.     

Magnetic properties and microstructures of single-layered Fe100 − xPtx films deposited onto heated substrates

The single-layered Fe_100 − xPt_x films of 30 nm thick with Pt contents (x) of 35-57 at.% are deposited on heated Si (100) substrate at a temperature (Ts) of 620 °C by magnetron co-sputtering. When the Pt content in the Fe-Pt alloy film is 35 at.%, the value of in-plane coercivity (Hc_//) is close to perpendicular coercivity (Hc_⊥) and both values are about 800 kA/m. The FePt films exhibit perpendicular magnetic anisotropy when the Pt content increases to the values of between 45 and 51 at.%. The perpendicular coercivity, saturation magnetization (Ms) and perpendicular squareness (S_⊥) for Fe₅₄Pt₄₆ film are as high as 1113 kA/m, 0.594 Wb/m² and 0.96, respectively. These magnetic properties reveal its significant potential as perpendicular magnetic recording media. Upon further increasing the Pt content to 57 at.%, the coercivity of the Fe-Pt film decreases drastically to below 230 kA/m and tends to be closer to in-plane magnetic anisotropy.     

L10 ordered FePt based double-layered perpendicular recording media with (002) oriented FeCo films as a soft magnetic underlayer

The introduction of the soft magnetic underlayer (SUL) in perpendicular recording technology is to further increase the recording areal density. However, problems such as growth of the uncontrollable recording layer and additional media noise contributed from the SUL could be resulted. In this work, a synthetic antiferromagnetically (SAF) coupled (002) oriented Fe₆₅Co₃₅ film as an SUL was developed for L1₀ ordered FePt based double-layered recording media. The crystallography of hetero-epitaxially grown double-layered media CrRu/(Ru/FeCo)₂/Pt/FePt/Ru was demonstrated. The L1₀ ordered FePt based double-layered perpendicular recording media with SAF coupled FeCo films as the SUL were developed.     

Structure and optical properties of Zr1−xSixN thin films on sapphire

A series of zirconium silicon nitride (Zr_1−xSi_xN) thin films were grown on r-plane sapphire substrates using reactive RF magnetron co-sputtering of Zr and Si targets in a N₂/Ar plasma. X-ray diffraction pole figure analysis, X-ray reflectivity, X-ray photoelectron spectroscopy (XPS), optical microscopy, and optical absorption spectroscopy were used to characterize the film stoichiometries and structures after growth at 200 °C and post-deposition annealing up to 1000 °C in ultra-high vacuum. The atomically clean r-plane sapphire substrates induce high quality (100) heteroepitaxy of ZrN films rather than the (111) orientation observed on steel and silicon substrates, but the addition of Si yields amorphous films at the 200 °C growth temperature. After the annealing treatment, films with Si content x < 0.15 have compressive stress and crystallize into a polycrystalline structure with (100) fiber texture. For x > 0.15, the films are amorphous and remain so even after ultra-high vacuum annealing at 1000 °C. XPS spectra indicate that the bonding changes from covalent to more ionic in character as Si―N bonds form instead of Zr―N bonds. X-ray reflectivity, atomic force microscopy (AFM) and optical microscopy data reveal that after post-deposition annealing the 100 nm thick films have an average roughness < 2 nm, except for Si content near x = 0.15 corresponding to where the film becomes amorphous rather than being polycrystalline. At this stoichiometry, evidence was found for regions of film delamination and hillock formation, which is presumably driven by strain at the interface between the film and sapphire substrate. UV-visible absorption spectra also were found to depend on the film stoichiometry. For the amorphous Si-rich films (x > 0.15), the optical band gap increases with Si content, whereas for Zr-rich films (x < 0.15), there is no band gap and the films are highly conductive.     

FePtAg-C纳米颗粒薄膜的制备及表征

采用磁控溅射法在硅基片上生长FePt纳米颗粒薄膜。在硅片表面生长MgO籽层用来引发FePt合金薄膜的fct织构,加入C来减小其颗粒尺寸,加入Ag来增强其L10有序度。采用X射线衍射仪（XRD）、超导量子干涉仪（SQUID）和高分辨率透射电镜（TEM）对FePt薄膜进行表征。结果表明制备的薄膜样品具有优良的L10相结构,其M-H曲线表明方形度很好,垂直矫顽力HC有2467 kA/m,颗粒大小为10.4 nm。该薄膜非常适合用做下一代高密度磁存储媒质,可有效提高信息存储密度。     

Structural and optical properties of Ti-doped ZnO thin films prepared by the cathodic vacuum arc technique with different annealing processes

Highly transparent Ti-doped ZnO thin films were prepared on glass substrates at a deposition rate of approximately 33 nm/min using the cathodic vacuum arc technique with a Zn target power of 550 W and a Ti target power of 750 W, respectively. X-ray diffraction measurements have shown that the Ti-doped ZnO thin film with a vacuum post-annealing condition is c-axis oriented but an amorphous phase at the other post-annealing atmosphere and as-deposited condition. Transmittance measurements show that the best optical quality of the Ti-doped ZnO thin films occurred at a post-annealing atmosphere of N₂/H₂ mixed gases. Additionally, the optical transmittance of all films has been found more than 85% in a range of 500-700 nm. The lowest electrical resistivity was 3.48 × 10⁻³ Ω cm, obtained on as-deposited films. However, the post-annealing condition greatly increased the resistivity.