The effect of Bi1.5Zn0.5Nb0.5Ti1.5O7 cover layer on the dielectric and tunable properties of Ba0.6Sr0.4TiO3/Bi1.5Zn0.5Nb0.5Ti1.5O7 bilayered thin films

Bi_1.5Zn_0.5Nb_0.5Ti_1.5O₇ (BZNT) thin films with different thicknesses as cover layers were deposited on the Ba_0.6Sr_0.4TiO₃ (BST) thin films on the Pt/Ti/SiO₂/Si substrates by radio frequency magnetron sputtering method. The microstructure, surface morphology, dielectric and tunable properties of BST/BZNT heterogeneous bilayered films were investigated as a function of the thickness of BZNT films and the effect of BZNT films on the asymmetric electrical properties of BST/BZNT bilayered films was discussed. It was found that BZNT cover layer significantly improved the leakage current and the dielectric loss, and the dielectric constant and tunability of BST/BZNT bilayered thin films simultaneously decreased with the increasing thickness of BZNT films. The BST/BZNT bilayered thin film with a 50 nm BZNT cover layer gave the largest figure of merit (FOM) of 33.48 with the upper tunability of 55.38%. The asymmetric electrical behavior of BST/BZNT bilayered films is probably related to an internal electric field caused by built-in voltages at Pt/BST and BZNT/Au interfaces.     

Enhanced tunable dielectric properties of Ba0.5Sr0.5TiO3/Bi1.5Zn1.0Nb1.5O7 multilayer thin films by a sol-gel process

Ba_0.5Sr_0.5TiO₃(BST)/Bi_1.5Zn_1.0Nb_1.5O₇(BZN) multilayer thin films were prepared on Pt/Ti/SiO₂/Si substrates by a sol-gel method. The structures and morphologies of BST/BZN multilayer thin films were analyzed by X-ray diffraction (XRD) and field-emission scanning electron microscope. The XRD results showed that the perovskite BST and the cubic pyrochlore BZN phases can be observed in the multilayer thin films annealed at 700 °C and 750 °C. The surface of the multilayer thin films annealed at 750 °C was smooth and crack-free. The BST/BZN multilayer thin films annealed at 750 °C exhibited a medium dielectric constant of around 147, a low loss tangent of 0.0034, and a relative tunability of 12% measured with dc bias field of 580 kV/cm at 10 kHz.     

Large area Ba1 − xSrxTiO3 thin films for microwave applications deposited by pulsed laser ablation

Large area Ba_1 − xSr_xTiO₃ (BST) thin films with x = 0.4 or x = 0.5 were deposited on 75 mm diameter Si wafers in a pulsed laser deposition (PLD) chamber enabling full-wafer device fabrication using standard lithography. The deposition conditions were re-optimized for large PLD chambers to obtain uniform film thickness, grain size, crystal structure, orientation, and dielectric properties of BST films. X-ray diffraction and microstructural analyses on the BST films grown on Pt/Au/Ti electrodes deposited on SiO₂/Si wafers revealed films with (110) preferred orientation with a grain size < 100 nm. An area map of the thickness and crystal orientation of a BST film deposited on SiO₂/Si wafer also showed (110) preferred orientation with a film thickness variation < 6%. Large area BST films were found to have a high dielectric tunability of 76% at an electric field of 400 kV/cm and dielectric loss tangent below 0.03 at microwave frequencies up to 20 GHz and a commutation quality factor of ~ 4200.     

Investigation of BST thin films deposited by RF magnetron sputtering in pure Argon

Ba_0.5Sr_0.5TiO₃ (BST) thin films were deposited by rf magnetron sputtering using a Ba_0.5Sr_0.5TiO₃ target in pure Argon on two electrodes (Pt and RuO₂) at room temperature. The interface formation between BST and bottom electrode (Pt or RuO₂) was investigated by XPS for thicknesses in the 1 to 50 nm range. The chemical composition of the BST layers can be modified by the electrode nature over the first five nanometers. A 1 h ex-situ annealing, under flowing oxygen at 600 °C, was necessary to obtain crystallized 150 nm thick BST films, as evidenced by XRD and TEM analysis.     

Crystallization and electrical properties of Ba<Subscript>0.7</Subscript>Sr<Subscript>0.3</Subscript>TiO<Subscript>3</Subscript> thin films on SrRuO<Subscript>3</Subscript>/Pt hybrid bottom electrode

Ba_0.7Sr_0.3TiO₃ (BST) thin films were deposited on Pt and SrRuO₃(SRO)/Pt hybrid bottom electrodes by radio frequency magnetron sputtering. X-ray analysis indicated that both films were polycrystalline. Dielectric measurements showed that the films on SRO/Pt hybrid bottom electrode had lower dielectric constant and loss than the films on single Pt and the dielectric properties were frequency-independent. The leakage current density of Ba_0.7Sr_0.3TiO₃ thin films on hybrid bottom electrode was also lower. Leakage mechanism investigations showed that the contact between the electrode-film interfaces of thin films on SRO/Pt hybrid bottom electrode was ohmic. Based on the results, the effects of SRO/Pt hybrid bottom electrode on the crystallization and electrical properties of BST thin films were discussed.     

Interfacial characteristic of (Ba,Sr)TiO3 thin films deposited on different bottom electrodes

Barium strontium titanate (Ba_1?x Sr _x )TiO₃ (BST) thin films were deposited on Pt, Ru, RuO₂, and Pt/RuO₂ electrodes by radio frequency magnetron sputtering. The interfacial structure characteristic of the BST films deposited on various electrodes was investigated. X-ray photoelectron spectroscopy investigations showed that the interfacial diffusion layer in BST/Pt and BST/Ru are approximately 6 and 10 nm, respectively. The BST films are short of Ba and O elements comparing with the stoichiometry Ba_0.65Sr_0.35TiO₃ in the interface region. Dielectric measurement of the BST films with thickness ranging from 70 to 400 nm revealed that the BST films deposited on Pt and Pt/RuO₂ bottom electrodes have similar dielectric property, the BST films deposited on Ru have the highest bulk dielectric constant, and the thickness dependence of dielectric constant on the BST film deposited on RuO₂ electrode can be neglected. The interfacial layer dielectric constant of BST films deposited on Pt and Ru electrodes are estimated to be about 34.5 and 157.1, respectively. The effect of interfacial dead-layer on the dielectric constant could be eliminated through selecting appropriate bottom electrodes.     

Impedance spectroscopy and relaxation phenomena of (Na,K) excess Na0.5K0.5NbO3 thin films grown by chemical solution deposition

Na_0.5K_0.5NbO₃ (NKN) and 10 mol% (Na,K) excess Na_0.5K_0.5NbO₃ (NKN10) thin films on Pt/Ti/SiO₂/Si substrate were prepared by chemical solution deposition. Crystallization of NKN10 thin films was confirmed by X-ray diffraction. The (Na,K) excess Na_0.5K_0.5NbO₃ thin film shows a ferroelectric P-E hysteresis loop. Dielectric properties and impedance spectroscopy of thin films were investigated in the frequency range from 0.1 Hz to 100 kHz and the temperature range of 25 ~ 500 °C. By analyzing the complex impedance relaxation with Cole-Cole plots, we found impedance relaxations for the thin film. The contribution of electrical conduction is discussed in relation to grain, grain boundary, and interface effects.     

The effects of oxygen partial pressure on BST thin films deposited on multilayered bottom electrodes

Ba_0.5Sr_0.5TiO₃ (BST) thin films have been deposited by r.f. magnetron sputtering on silicon and platinum-coated silicon substrates with different buffer and barrier layers. BST films deposited on Si/SiO₂/SiN/Pt and Si/SiO₂/Ti/TiN/Pt multilayer bottom electrode have been used for the fabrication of capacitors. XRD and SEM studies were carried out for the films. It was found that the crystallinity of the BST thin film was dependent upon oxygen partial pressure in the sputtering gas. The role of multilayered bottom electrode on the electrical properties of Ba_0.5Sr_0.5TiO₃ films has been also investigated. The dielectric properties of BST films were measured. The results show that the films exhibit pure perovskite phase and their grain sizes are about 80–90 nm. The dielectric properties of the BST thin film on Si/SiO₂/Ti/TiN/Pt electrode was superior to that of the film grown on Si/SiO₂/SiN/Pt electrode.     

Precursor chemistry for the solution deposition of epitaxial La0.66Sr0.33MnO3 (LSMO) thin films

A new chemical solution deposition method for the epitaxial growth of La_0.66Sr_0.33MnO₃ (LSMO) thin films from metal acetates, acetylacetonates and propionic acid is presented. Using this method, epitaxial LSMO thin films were grown on (001) SrTiO3 (STO) single crystalline substrates in the temperature range from 800 °C to 1100 °C, both in air and in oxygen atmosphere. The LSMO thin films exhibit good structural and electrical properties. The FWHM of the ω-scan for the (002) peak has a mean value of 0.06°. The Curie temperature of the LSMO thin films is about 320 K and 350 K for the annealed in oxygen and air, respectively.     

Interfacial characteristics and dielectric properties of Ba0.65Sr0.35TiO3 thin films

Ba_0.65Sr_0.35TiO₃ (BST) thin films were deposited on Pt/Ti/SiO₂/Si substrates by radio frequency magnetron sputtering technique. X-ray photoelectron spectroscopy (XPS) depth profiling data show that each element component of the BST film possesses a uniform distribution from the outermost surface to subsurface, but obvious Ti-rich is present to BST/Pt interface because Ti⁴⁺ cations are partially reduced to form amorphous oxides such as TiO_x (x < 2). Based on the measurement of XPS valence band spectrum, an energy band diagram in the vicinity of BST/Pt interface is proposed. Dielectric property measurements at 1 MHz reveal that dielectric constant and loss tangent are 323 and 0.0095 with no bias, while 260 and 0.0284 with direct current bias of 25 V; furthermore, tunability and figure of merit are calculated to be 19.51% and 20.54, respectively. The leakage current density through the BST film is about 8.96 × 10^− 7 A/cm² at 1.23 V and lower than 5.66 × 10^− 6 A/cm² at 2.05 V as well as breakdown strength is above 3.01 × 10⁵ V/cm.     

Bottom electrodes dependence of microstructures and dielectric properties of compositionally graded (Ba1−xSrx)TiO3 thin films

Compositionally graded (Ba_1−xSr_x)TiO₃ (BST) thin films, with x decreasing from 0.3 to 0, were deposited on Pt/Ti/SiO₂/Si and Ru/SiO₂/Si substrates by radio frequency magnetron sputtering technology. The microstructure and dielectric properties of the graded BST thin films were investigated. It was found that the films on Ru electrode have better crystallization, and that RuO₂ is present between the Ru bottom electrode and the graded BST thin films by X-ray diffraction and SEM analysis. Dielectric measurement reveals that the graded BST thin films deposited on Ru bottom electrode have higher dielectric constant and tunability. The enhanced dielectric behavior is attributed to better crystallization as well as smaller space charge capacitance width and the formation of RuO₂ that is more compatible with the BST films. The graded BST films on Ru electrode show higher leakage current due to lower barrier height and rougher surface of bottom electrode.     

The properties of Ba0.5Sr0.5TiO3 thin film prepared by RF magnetron sputtering from powder target

The Ba_0.5Sr_0.5TiO₃ (BST) thin film with the thickness of 400 nm deposited from powder target is prepared by the radio-frequency magnetron sputtering technique. The deposition rate of BST film is estimated to be 45 nm/min, which is very fast for ferroelectric materials. The dielectric properties of the as-prepared BST thin film are demonstrated. High dielectric tunability up to 42.7% and low dielectric loss small to 0.01 are achieved at a low applied voltage of 5 V. The results demonstrate that the RF magnetron sputtering from powder target is a versatile, novel technique for the deposition of high-quality ferroelectric thin films.     

Preparation,microstructure and dielectric properties of Ba0.5Sr0.5TiO3 thin films grown on Pt/Ti/SiO2/Si substrates by pulsed laser deposition

Barium strontium titanate Ba_0.5Sr_0.5TiO₃ (BST) thin films have been deposited on Pt/Ti/SiO₂/Si substrates by a pulsed laser deposition method. The low-frequency dielectric responses of the BST films, grown at different substrate temperatures (T_s), were measured as functions of frequency in the frequency range from 1 kHz to 1 MHz. With increase of T_s, the grain size of BST thin films became larger and the crystallinity was greatly improved, and then the dielectric permittivity increased, while the dielectric dispersion rose drastically. The origin of the large dielectric relaxation is believed to result from the aggravation of oxygen diffusion at the BST/Pt interface for the BST thin films grown at comparatively higher temperatures. This concept could be further explained by considering the influence of post-annealing in oxygen ambient on the dielectric properties of BST thin films. Our results reveal that the dielectric properties are strongly dependent on the processing conditions and the microstructure of thin films.     

Thickness-ratio-dependent dielectric properties of Bi1.5Zn1.0Nb1.5O7/Ba0.5Sr0.5TiO3 bilayered thin films

Bi_1.5Zn_1.0Nb_1.5O₇ (BZN)/Ba_0.5Sr_0.5TiO₃ (BST) thin films were prepared on Pt/Ti-coated sapphire substrates by radio frequency magnetron sputtering. The specific relationship between the dielectric properties and the thickness ratio of the BZN thickness to the BST thickness was investigated. The presence of BZN films effectively reduced the dielectric loss of the thin films. The thickness-ratio-dependent dielectric constant and dielectric loss behaviors were in good accordance with the simulation results based on the series connection theory. The optimum thickness ratio was determined to be around 0.5, exhibiting a maximum commutation quality factor of about 16,000. The built-in electric field at the region near the BZN–BST interface may be responsible for the asymmetric characteristic of the electric-field-dependent dielectric properties of the BZN/BST thin films.     

Structural and dielectric properties of Ba0.7Sr0.3TiO3 thin films grown on thin Bi layer-coated Pt(111)/Ti/SiO2/Si substrates

In this work, the growth and study of dielectric properties of Ba_0.7Sr_0.3TiO₃ (BST) thin films grown on thin Bi layer coated Pt(111)/Ti/SiO₂/Si substrates, depending on thin Bi layer thickness is reported. The BST thin film (thickness 180 nm) grown on 10-nm-thick Bi layer exhibited more improved structural and dielectric properties than that grown on bare Pt(111)/Ti/SiO₂/Si substrate. The 10-nm-thick Bi layer in optimum configuration was effective for the grain growth of BST phase and suppressed the formation of the oxygen-deficient layer at the interface between the BST thin film and bottom electrode, which resulted in an increase in dielectric constant and a decrease in leakage current density of the Pt/BST thin film/Pt capacitor.     

Role of La0.5Sr0.5CoO3 template layers on dielectric and electrical properties of pulsed-laser ablated Pb(Nb2/3Mg1/3)O3-PbTiO3 thin films

Relaxor ferroelectric thin films of 0.7Pb(Mg_1/3Nb_2/3)O₃-0.3PbTiO₃ (PMN-PT) deposited on platinized silicon substrates with and without template layers were studied. Perovskite phase (80% by volume) was obtained through proper selection of the processing conditions on bare Pt/Ti/SiO₂/Si substrates. The films were initially grown at 300 °C using pulsed-laser ablation and subsequently annealed in a rapid thermal annealing furnace in the temperature range of 750-850 °C to induce crystallization. Comparison of microstructure of the films annealed at different temperatures showed change in perovskite phase formation and grain size etc. Results from compositional analysis of the films revealed that the films initially possessed high content of lead percentage, which subsequently decreased after annealing at temperature 750-850 °C. Films with highest perovskite content were found to form at 820-840 °C on Pt substrates where the Pb content was near stoichiometric. Further improvement in the formation of perovskite PMN-PT phase was obtained by using buffer layers of La_0.5Sr_0.5CoO₃ (LSCO) on the Pt substrate. This resulted 100% perovskite phase formation in the films deposited at 650 °C. Dielectric studies on the PMN-PT films with LSCO template layers showed high values of relative dielectric constant (3800) with a loss factor (tan δ) of 0.035 at a frequency of 1 kHz at room temperature.     

Preparation and characterization of Ba1 − xSrxTiO3 thin films deposited on Pt/SiO2/Si by sol-gel method

BST thin films have been investigated as potential candidates for use in frequency agile microwave circuit devices. Stoichiometric (Ba_1 − xSr_x)TiO₃ (BST) thin films have been prepared on Pt/SiO₂/Si substrates using sol-gel method. The BST films were characterized by X-ray fluorescence (XRF) spectroscopy analysis, X-ray diffraction (XRD), scanning electron microscope (SEM) and electrical measurements. The relationships of processing parameters, microstructures, and dielectric properties are discussed. The results show that the films exhibit pure perovskite phase through rapid thermal anneal at 700 °C and their grain sizes are about 20-40 nm. The dielectric constants of BST5, BST10, BST15 and BST20 are 323, 355, 382 and 405, respectively, at 80 kHz.     

Preparation and colossal magnetoresistance in a trilayer La0.67Sr0.33MnO3/La0.75MnO3/La0.67Sr0.33MnO3 device by dc magnetron sputtering

Epitaxial trilayer films of La_0.67Sr_0.33MnO₃ (LSMO)/La_0.75MnO₃ (L0.75MO)/La_0.67Sr_0.33MnO₃ (LSMO) have been prepared on (0 0 1) oriented LaAlO₃ substrates by dc magnetron sputtering. The structure and MR are studied. All as-deposited trilayer films exhibit a semiconductor to metal transition at temperature ranging from 116 to 185 K. The MR is also shown to be dependent on the thickness of the middle oxide layer. A maximum MR value of 32% (ΔR/R₀) has been obtained at 132 K under 0.4 T magnetic field for a LSMO (300 nm)/L0.75MO (70 nm)/LSMO (300 nm) trilayer film. The MR of trilayer film prefers to that of both LSMO and L0.75MO single layer films.     

Variations of microstructures and electrical properties of Bi4Ti3O12/SrTiO3/(La0.5, Sr0.5)CoO3/MgO epitaxial thin films by annealing

Epitaxial thin films of a heterostructure with Bi₄Ti₃O₁₂(BIT)/SrTiO₃(ST) were successfully grown with a bottom electrode consisting of La_0.5Sr_0.5CoO₃(LSCO) on MgO(001) substrates using pulsed laser deposition. The grown BIT and ST (001) planes were parallel to the growth surface with the orientation relationship of BIT <110>//ST <010>. In the as-deposited film, the BIT (001) plane appeared to expand to relieve a lattice mismatch with the ST (001) plane. However, annealing for 20-40 min induced the BIT (001) plane to contract horizontally with its c-axis expanding, which was associated with a local perturbation in the layer stacking of the BIT structure. This structural distortion was reduced in the film annealed for 1 h, with restoration of the periodicity of the layer stacking. Correspondingly, the dielectric constant of the as-deposited film was increased from 292 to 411 by annealing for 1 h. In parallel, the film was paraelectric but became more ferroelectric, with the remanent polarization and the coercive field changing from 0.1 μC/cm² and 14 kV/cm to 1.7 μC/cm² and 69 kV/cm, respectively.     

Improved dielectric properties of CaCu3Ti4O12 thin films on oxide bottom electrode of La0.5Sr0.5CoO3

We report on the effect of La_0.5Sr_0.5CoO₃ (LSCO) bottom electrode to the dielectric properties of CaCu₃Ti₄O₁₂ (CCTO) thin films grown on Ir/Ti/SiO₂/Si substrates. Compared with the films grown directly on Ir/Ti/SiO₂/Si substrates, the dielectric constant has been increased greatly about 100%, and the dielectric loss decreased to lower than 0.2 in the frequency range of 1-100 kHz. The origin has been discussed in details based on the analysis of the X-ray diffraction and impedance spectra measurements. Results of the impedance spectra suggest that the absence of undesired interfacial layer between Ir/CCTO thin films might be one of the major reasons of the improvement of the dielectric properties when the LSCO was introduced as the bottom electrode.