Enhancement of the energy storage properties of supercapacitors using graphene nanosheets dispersed with metal oxide-loaded carbon nanotubes

Graphene nanosheets (GNs) dispersed with SnO₂ nanoparticles loaded multiwalled carbon nanotubes (SnO₂-MWCNTs) were investigated as electrode materials for supercapacitors. SnO₂-MWCNTs were obtained by a chemical method followed by calcination. GNs/SnO₂-MWCNTs nanocomposites were prepared by ultrasonication of the GNs and SnO₂-MWCNTs. Electrochemical double layer capacitors were fabricated using the composite as the electrode material and aqueous KOH as the electrolyte. Electrochemical performance of the composite electrodes were compared to that of pure GNs electrodes and the results are discussed. Electrochemical measurements show that the maximum specific capacitance, power density and energy density obtained for supercapacitor using GNs/SnO₂-MWCNTs nanocomposite electrodes were respectively 224 F g⁻¹, 17.6 kW kg⁻¹ and 31 Wh kg⁻¹. The fabricated supercapacitor device exhibited excellent cycle life with ∼81% of the initial specific capacitance retained after 6000 cycles. The results suggest that the hybrid composite is a promising supercapacitor electrode material.     

Supercapacitive properties of polyaniline/Nafion/hydrous RuO2 composite electrodes

Chemically prepared polyaniline is tested for its supercapacitive behaviour in an aqueous electrolyte of 1.0 M H₂SO₄. In order to improve the cycleability of the polyaniline electrode, it is made into a composite with Nafion. This composite electrode shows improved cycleability and higher specific capacitance compared with a pure polyaniline electrode. It is therefore used as a matrix for the electrochemical deposition of hydrous RuO₂. The resulting ternary composite electrode has a high specific capacitance of 475 F g⁻¹ at 100 mV s⁻¹ and 375 F g⁻¹ at 1000 mV s⁻¹ in the voltage range of −0.2 to 0.8 V versus Ag/AgCl. All three types of electrode are characterized by cyclic voltammetry and impedance anaylsis.     

Electrodeposition and pseudocapacitive properties of tungsten oxide/polyaniline composite

Composite films of tungsten oxide (WO₃) and polyaniline (PANI) have been electrodeposited by cyclic voltammetry in a mixed solution of aniline and precursor of tungsten oxide. Surface morphology and chemical composition of WO₃/PANI composite are characterized by scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). The influence of H₂O₂ on the electrodeposition of WO₃/PANI composite film is also investigated. Cyclic voltammetry (CV), chronopotentiometry (CP) and electrochemical impedance spectroscopy (EIS) results show that WO₃/PANI composite film exhibit good pseudocapacitive performance over a wide potential range of −0.5 to 0.7 V vs. SCE with the specific capacitance of 168 F g⁻¹ at current density of 1.28 mA cm⁻² and energy density of 33.6 Wh kg⁻¹, which is 91% higher than that of similarly prepared PANI (17.6 Wh kg⁻¹). An asymmetric model capacitor using WO₃/PANI as negative and PANI as positive electrodes over voltage range of 1.2 V displays a specific capacitance of 48.6 F g⁻¹ and energy density of 9.72 Wh kg⁻¹ at the power density of 53 W kg⁻¹, which is two times higher than that of a symmetric capacitor modeled by using two PANI films as both positive and negative electrodes.     

Preparation of graphene nanosheet/carbon nanotube/polyaniline composite as electrode material for supercapacitors

Graphene nanosheet/carbon nanotube/polyaniline (GNS/CNT/PANI) composite is synthesized via in situ polymerization. GNS/CNT/PANI composite exhibits the specific capacitance of 1035 F g⁻¹ (1 mV s⁻¹) in 6 M of KOH, which is a little lower than GNS/PANI composite (1046 F g⁻¹), but much higher than pure PANI (115 F g⁻¹) and CNT/PANI composite (780 F g⁻¹). Though a small amount of CNTs (1 wt.%) is added into GNS, the cycle stability of GNS/CNT/PANI composite is greatly improved due to the maintenance of highly conductive path as well as mechanical strength of the electrode during doping/dedoping processes. After 1000 cycles, the capacitance decreases only 6% of initial capacitance compared to 52% and 67% for GNS/PANI and CNT/PANI composites.     

Aqueous dispersed conducting polyaniline nanofibers: Promising high specific capacity electrode materials for supercapacitor

Aqueous dispersed conducting polyaniline nanofiber, new electrode material for supercapacitor, is prepared employing acidic phosphate ester as dopant for nanofibrous polyaniline emeraldine base, which is synthesized by polymerization of aniline using ferric nitrate as oxidant through pseudo-high dilution technique. Highly crystalline and uniform polyaniline fibers with thin diameter of 17-26 nm are obtained, the film from which shows electrical conductivity of 32 S cm⁻¹. The thin nanofibrous polyaniline is used as electrode material for supercapacitor and its performance is evaluated in non-protonic solvent system. It shows a specific capacitance as high as 160 F g⁻¹ at discharge rate of 0.4 A g⁻¹ from −1 V to 1 V in 1 mol L⁻¹ tetraethylammonium tetrafluoroborate/propylene carbonate solution, and the discharge/charge efficiency reaches 92%, indicating that it possesses good electrochemical reversibility. The high capacitance can be attributed to its relatively high surface area of 70 m² g⁻¹, which is 3-5 times higher than spherical polyaniline or thick fiberous polyaniline, leading to high utilization of the electroactive materials.     

Supercapacitive properties of hybrid films of manganese dioxide and polyaniline based on active carbon in organic electrolyte

This is the first report about supercapacitive performance of hybrid film of manganese dioxide (MnO₂) and polyaniline (PANI) in an organic electrolyte (1.0 M LiClO₄ in acetonitrile). In this work, a high surface area and conductivity of active carbon (AC) electrode is used as a substrate for PANI/MnO₂ film electro-codeposition. The redox properties of the coated PANI/MnO₂ thin film exhibit ideal capacitive behaviour in 1 M LiClO₄/AN. The specific capacitance (SC) of PANI/MnO₂ hybrid film is as high as 1292 F g⁻¹ and maintains about 82% of the initial capacitance after 1500 cycles at a current density of 4.0 mA cm⁻², and the coulombic efficiency (η) is higher than 95%. An asymmetric capacitor has been developed with the PANI/MnO₂/AC positive and pure AC negative electrodes, which is able to deliver a specific energy as high as 61 Wh kg⁻¹ at a specific power of 172 W kg⁻¹ in the range of 0-2.0 V. These results indicate that the organic electrolyte is a promising candidate for PANI/MnO₂ material application in supercapacitors.     

Preparation and electrochemical capacitance performances of super-hydrophilic conducting polyaniline

Super-hydrophilic conducting polyaniline was prepared by surface modification of polyaniline using tetraethyl orthosilicate in water/ethanol solution, whereas its conductivity was 4.16 S cm⁻¹ at 25 °C. And its electrochemical capacitance performances as an electrode material were evaluated by the cyclic voltammetry and galvanostatic charge/discharge test in 0.1 M H₂SO₄ aqueous solution. Its initial specific capacitance was 500 F g⁻¹ at a constant current density of 1.5 A g⁻¹, and the capacitance still reached about 400 F g⁻¹ after 5000 consecutive cycles. Moreover, its capacitance retention ratio was circa 70% with the growth of current densities from 1.5 to 20 A g⁻¹, indicating excellent rate capability. It would be a promising electrode material for aqueous redox supercapacitors.     

Electrochemical supercapacitor electrode material based on poly(3,4-ethylenedioxythiophene)/polypyrrole composite

Poly (3,4-ethylenedioxythiophene)/polypyrrole composite electrodes were prepared by electropolymerization of 3,4-ethylenedioxythiophene (EDOT) on the surface of polypyrrole (PPy) modified tantalum electrodes. The morphology observation of PPy and poly(3,4-ethylenedioxythiophene)/polypyrrole composite (PEDOT/PPy) was performed on Field Emission Scanning Electron Microscope (SEM). The electrochemical capacitance properties of the composite were investigated with cyclic voltammetry (CV), galvanostatic charge–discharge and electrochemical impedance spectroscopy (EIS) techniques in the two- or three-electrode cell system. The results show that the PEDOT/h-PPy (PPy with horn-like structure) composite films were characterized with highly porous structure, which leads to their specific capacitance as 230 Fg⁻¹ in 1 M LiClO₄ aqueous solutions and even 290 Fg⁻¹ in 1 M KCl aqueous solutions. Moreover, the composite exhibits a rectangle-like shape of voltammetry characteristics even at scanning rate 100 mV s⁻¹, a linear variation of the voltage with respect to time without a clear ohm-drop phenomenon in galvanostatic charge–discharge process and almost ideal capacitance behavior in low-frequency in 1 M KCl solutions. Furthermore, specific power of the composite would reach 13 kW kg⁻¹ and it had good cycle stability. All of the above imply that the PEDOT/h-PPy composites were an ideal electrode material of supercapacitor.     

Flexible supercapacitor based on polyaniline nanowires/carbon cloth with both high gravimetric and area-normalized capacitance

Flexible supercapacitor is successfully fabricated using polyaniline nanowires/carbon cloth (PANI-NWs/CC) nanocomposite. High gravimetric capacitance of 1079 F g⁻¹ at a specific energy of 100.9 Wh kg⁻¹ and a specific power of 12.1 kW kg⁻¹ is obtained. Moreover, this approach also offers an exceptionally high area-normalized capacitance of 1.8 F cm⁻². The diffusion length of protons within the PANI-NWs is estimated to be about 60 nm by electrochemical impedance analysis, which indicates that the electrochemical performance of the electrode is not limited by the thickness of PANI-NWs. The electrochemical performance of PANI-NWS/CC remains without any deterioration, even when the cell is bent under high curvature. These results clearly present a cost-effective and simple method of fabrication of the nanostructured polymers with enormous potential in flexible energy storage device applications.     

Construction of composite electrodes comprising manganese dioxide nanoparticles distributed in polyaniline-poly(4-styrene sulfonic acid-co-maleic acid) for electrochemical supercapacitor

This work demonstrated a novel and simple route for preparing a composite comprising of manganese oxide (MnO₂) nanoparticles and polyaniline (PANI) doped poly(4-styrene sulfonic acid-co-maleic acid) (PSSMA) by “electrochemical doping-deposition”. The PANI-PSSMA-MnO₂ composite was characterized by scanning electron microscopy (SEM)), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). SEM images revealed a uniform dispersion of MnO₂ nanoparticles in the porous structure of PANI-PSSMA structure. XRD measurements showed the distortion of the crystal structure of β-MnO₂ after deposition of MnO₂ in PANI-PSSMA structure. Thus, the XRD pattern of PANI was predominating. Cyclic voltammetry and chronopotentiometry were employed in 0.5 M Na₂SO₄ to evaluate the capacitor properties. The results showed a significant improvement in the specific capacitance of the composite electrode. The specific capacitance of PANI-PSSMA-MnO₂ (50.4 F g⁻¹) had improvement values of 172% compared to that of PANI (18.5 F g⁻¹). When only the MnO₂ mass was considered, the composite had a specific capacitance of 556 F g⁻¹.     

The preparation and performance of calcium carbide-derived carbon/polyaniline composite electrode material for supercapacitors

Calcium carbide (CaC₂)-derived carbon (CCDC)/polyaniline (PANI) composite materials are prepared by in situ chemical oxidation polymerization of an aniline solution containing well-dispersed CCDC. The structure and morphology of CCDC/PANI composite are characterized by Fourier infrared spectroscopy (FTIR), scanning electron microscope (SEM), transmission electron microscopy (TEM) and N₂ sorption isotherms. It has been found that PANI was uniformly deposited on the surface and the inner pores of CCDC. The supercapacitive behaviors of the CCDC/PANI composite materials are investigated with cyclic voltammetry (CV), galvanostatic charge/discharge and cycle life measurements. The results show that the CCDC/PANI composite electrodes have higher specific capacitances than the as grown CCDC electrodes and higher stability than the conducting polymers. The capacitance of CCDC/PANI composite electrode is as high as 713.4 F g⁻¹ measured by cyclic voltammetry at 1 mV s⁻¹. Besides, the capacitance retention of coin supercapacitor remained 80.1% after 1000 cycles.     

Growth of polyaniline nanowhiskers on mesoporous carbon for supercapacitor application

Vertically aligned polyaniline nanowhiskers (PANI-NWs) doped with (1R)-(−)-10-Camphorsulfonic acid (L-CSA) have been successfully synthesized on the external surface of ordered mesoporous carbon (CMK-3) by chemical oxidative polymerization. The specific surface area of the PANI-NWs/CMK-3 nanocomposite remains as high as 497 m² g⁻¹ by removing mesoporous silica template after the polymerization of aniline. Structural and morphological characterizations of the nanocomposite were further investigated by XRD, FTIR and FE-SEM measurements. The result shows that the nanocomposite with 40 wt% PANI applying in supercapacitor devices possesses a large specific capacitance of 470 F g⁻¹ and good capacitance retention of 90.4% is achieved after 1000 cycles at a current density of 1.0 A g⁻¹. The synergistic effect of small PANI nanowhisker arrays and well-ordered mesoporous carbon endows the composite with high electrochemical capacitance and good cycling stability.     

Polypyrrole/carbon aerogel composite materials for supercapacitor

Polypyrrole (PPy)/carbon aerogel (CA) composite materials with different PPy contents are prepared by chemical oxidation polymerization through ultrasound irradiation and are used as active electrode material for supercapacitor. The morphology of PPy/CA composite is examined by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results show that PPy is deposited onto the surface of CA. As evidenced by cyclic voltammetry, galvanostatic charge/discharge test and EIS measurements, PPy/CA composites show superior capacitive performances to CA, moreover, the results based on cyclic voltammograms show that the composite material has a high specific capacitance of 433 F g⁻¹, while the capacitance of CA electrode is only 174 F g⁻¹. Although the supercapacitor used PPy/CA as active electrode material has an initial capacitance loss due to the instability of PPy, the specific capacitance after 500 cycles stabilizes nearly at a fixed value.     

A doped activated carbon prepared from polyaniline for high performance supercapacitors

A novel doped activated carbon has been prepared from H₂SO₄-doped polyaniline which is prepared by the oxypolymerization of aniline. The morphology, surface chemical composition and surface area of the carbon have been investigated by scanning electron microscope, X-ray photoelectron spectroscopy and Brunaner-Emmett-Teller measurement, respectively. Electrochemical properties of the doped activated carbon have been studied by cyclic voltammograms, galvanostatic charge/discharge, and electrochemical impedance spectroscopy measurements in 6 mol l⁻¹ KOH. The specific capacitance of the carbon is as high as 235 F g⁻¹, the specific capacitance hardly decreases at a high current density 11 A g⁻¹ after 10,000 cycles, which indicates that the carbon possesses excellent cycle durability and may be a promising candidate for supercapacitors.     

Electrochemical properties of leucoemeraldine, emeraldine, and pernigraniline forms of polyaniline/multi-wall carbon nanotube nanocomposites for supercapacitor applications

We report on the synthesis and electrochemical properties of leucoemeraldine base, emeraldine salt and pernigraniline base forms of polyaniline (PANI) in the form of nanocomposites with MWNTs. The oxidation state of PANI in the composite is controlled by doping and dedoping of the emeraldine salt form of PANI/MWNT composite, which is prepared through chemical polymerization, using oxidizing and reducing agents without changing the morphology of PANI in the composite and is confirmed by ultraviolet-visible spectroscopy (UV-vis) spectroscopy and Fourier transform infrared (FT-IR) spectroscopy. The electrochemical and pseudocapacitive properties of the composites are investigated using cyclic voltammetry and analyzed with respect to the oxidation state of polyaniline. The PANI/MWNT nanocomposites show specific capacitance values of 217 F g⁻¹, 328 F g⁻¹ and 139 F g⁻¹ for leucoemeraldine base, emeraldine salt and pernigraniline base, respectively. Electrochemical impedance spectroscopy is performed to explain the different electrochemical properties of PANI in different oxidation states.     

Electrodeposition of manganese dioxide in three-dimensional poly(3,4-ethylenedioxythiophene)–poly(styrene sulfonic acid)–polyaniline for supercapacitor

The preparation of composites of precise metal oxides/conducting polymers is important in studies of supercapacitors. In this work, a three-dimensional matrix of poly(3,4-ethylenedioxythiophene)–poly(styrene sulfonic acid)–polyaniline (PEDOT–PSS–PANI) was prepared by interfacial polymerization of ANI into PEDOT–PSS. Conductivity was enhanced by incorporating of PANI into PEDOT–PSS because of the decrease in the distance for electron shuttling along the conjugated polymeric chain. Composite electrodes were prepared by the electrodeposition of manganese dioxide (MnO₂) in a PEDOT–PSS–PANI three-dimensional matrix. The electrodes were characterized by field emission scanning electron microscopy (FE-SEM), X-ray photoelectron spectroscopy (XPS), and cyclic voltammetry techniques. The results show a significant improvement in the specific capacitance of the composite electrode. For PEDOT–PSS the specific capacitance was of 0.23 F g⁻¹, while PEDOT–PSS–PANI and PEDOT–PSS–PANI–MnO₂ displayed values of 6.7 and 61.5 F g⁻¹, respectively. When only considering the MnO₂ mass, the composite had the specific capacitance of 372 F g⁻¹. The composite also had an excellent cyclic performance.     

Electrochemical capacitance of NiO/Ru0.35V0.65O2 asymmetric electrochemical capacitor

A designed asymmetric hybrid electrochemical capacitor was presented where NiO and Ru_0.35V_0.65O₂ as the positive and negative electrode, respectively, both stored charge through reversible faradic pseudocapacitive reactions of the anions (OH⁻) with electroactive materials. And the two electrodes had been individually tested in 1 M KOH aqueous electrolyte to define the adequate balance of the active materials in the hybrid system as well as the working voltage of the capacitor based on them. The electrochemical tests demonstrated that the maximum specific capacitance and energy density of the asymmetric hybrid electrochemical capacitor were 102.6 F g⁻¹ and 41.2 Wh kg⁻¹, respectively, delivered at a current density of 7.5 A cm⁻². And the specific energy density decreased to 23.0 Wh kg⁻¹ when the specific power density increased up to 1416.7 W kg⁻¹. The hybrid electrochemical capacitor also exhibited a good electrochemical stability with 83.5% of the initial capacitance over consecutive 1500 cycle numbers.     

CoO-loaded graphitable carbon hollow spheres as anode materials for lithium-ion battery

A new type of CoO nanoparticles encapsulated by graphitable hollow carbon sphere (GHCS) composite material was synthesized. The core–shell structure CoO/GHCS composite shows the improved cyclability as an anodic material in Li-ion battery. The core–shell composite containing 50 wt% CoO exhibits a reversible capacity of 584 mAh g⁻¹ at a constant current density of 100 mA g⁻¹ between 0 and 3.0 V (vs. Li⁺/Li), and remains a capacity retention of 95% after 50th cycle. The improvement could be attributed to that the GHCS with a good electronic conductivity and high surface severs as dispersing medium to prevent CoO nanoparticles from aggregating, and provide the enough space to buffer the volume change during the Li-ion insertion and extraction reactions in CoO nanoparticles.     

Electrochemical performance of carbon-coated lithium manganese silicate for asymmetric hybrid supercapacitors

Nanoscale carbon-coated Li₂MnSiO₄ powder is prepared using a conventional solid-state method and can be used as the negative electrode in a Li₂MnSiO₄/activated carbon (AC) hybrid supercapacitor. Carbon-coated Li₂MnSiO₄ material presents a well-developed orthorhombic crystal structure with a Pmn2₁ space group, although there is a small impurity of MnO. The maximum specific capacitance of the Li₂MnSiO₄/AC hybrid supercapacitor is 43.2 F g⁻¹ at 1 mA cm⁻² current density. The cell delivers a specific energy as high as 54 Wh kg⁻¹ at a specific power of 150 W kg⁻¹ and also exhibits an excellent cycle performance with more than 99% columbic efficiency and the maintenance of 85% of its initial capacitance after 1000 cycles.     

Preparation and enhanced capacitance of core–shell polypyrrole/polyaniline composite electrode for supercapacitors

Polypyrrole (PPy) nanotubes were synthesized by using the complex of methyl orange (MO)/FeCl₃ as a template. Then the core–shell polypyrrole/polyaniline (PPy/PANI) composite was prepared by in situ chemical oxidation polymerization of aniline on the surface of PPy nanotubes. The morphology and molecular structure were characterized by transmission electron microscopy (TEM), infrared spectroscopy (IR) and X-ray diffraction (XRD). TEM images confirmed that the composite was core–shell nanotubes. The electrochemical properties of the PPy/PANI composite electrode were investigated by cyclic voltammetry (CV), galvanostatic charge–discharge and electrochemical impedance spectroscopy (EIS). The electrochemical experiments showed that the specific capacitance of the PPy/PANI composite was 416 F g⁻¹ in 1 M H₂SO₄ electrolyte and 291 F g⁻¹ in 1 M KCl electrolyte. Furthermore, the composite electrode exhibited a good rate capability and maintained 91% of initial capacity at a current density of 15 mA cm⁻² in 1 M H₂SO₄ electrolyte.