On the photophysical and electrochemical studies of dye-sensitized solar cells with the new dye CYC-B1

In this study, the photoelectrochemical characteristics of a ruthenium photosensitizer with an alkyl bithiophene group, designated as CYC-B1, are studied. The effect of mesoporous TiO₂ film thickness on the photovoltaic performance of CYC-B1 and N3 dye-sensitized solar cells was investigated. The performance of the dye-sensitized nanocrystalline TiO₂ solar cells (DSSC) fabricated using CYC-B1 dye-anchored TiO₂ photoelectrode showed a convincing enhancement in cell efficiency when the TiO₂ film thickness was increased from 3 μm (eff.=5.41%) to 6 μm (eff.=7.19%). The efficiency of the CYC-B1-sensitized DSSC was maximum at 6 μm of the TiO₂ film thickness, reached its limiting value and remained constant up to 53 μm, although a similar trend was also observed for N3 dye-sensitized DSSC, however, the maximum efficiency achieved was only at 27 μm thickness (eff.=6.75%). As expected, the photocurrent density generated in the DSSC modified by CYC-B1 dye is larger than that from N3 dye. The effect of guanidinium thiocyanate (GuSCN) (additive) addition to the electrolyte on the photovoltaic performance of DSSCs based on CYC-B1 was also investigated. Furthermore, the electrochemical impedance spectroscopy (EIS) technique and photo-transient laser method have been employed to analyze the charge transfer resistances (R_ct) and the lifetime of the injected electrons on the TiO₂ containing different thicknesses.     

Low-temperature oxygen plasma treatment of TiO2 film for enhanced performance of dye-sensitized solar cells

The effects of low-temperature O₂ plasma treatment of a TiO₂ film are studied with the objective of improving the performance of dye-sensitized solar cells (DSSCs). X-ray photoelectron spectra (XPS) reveal that the ratio of titanium dioxide to titanium sub-oxides is increased in the O₂ plasma-treated TiO₂ film, compared with that of the untreated TiO₂ film. This increase suggests that the oxygen vacancies in the film are effectively reduced. The near-edge X-ray absorption fine structure (NEXAFS) spectra results agree with the XPS result. It is proposed that there is a correlation between the shifts of the peaks in the NEXAFS spectra and the adsorption of N719 dye on the TiO₂ particles. A DSSC having an O₂ plasma-treated, 4 μm thick TiO₂ film electrode renders a short-circuit photocurrent of 7.59 mA cm⁻², compared with 6.53 mA cm⁻² for a reference cell with an untreated TiO₂ electrode of the same thickness. As a result of these changes, the solar-to-electricity conversion efficiency of the O₂ plasma-treated cell is found to be 4.0% as compared with 3.5% for the untreated cell. This improvement in the performance is rationalized on the basis of increased N719 dye adsorption on to the TiO₂, due to the reduction in the number of oxygen vacancies caused by the oxygen plasma treatment.     

Dye-sensitized solar cells with a micro-porous TiO2 electrode and gel polymer electrolytes prepared by in situ cross-link reaction

The ionic conductivities and performances of dye-sensitized solar cells (DSSCs) of gel polymer electrolytes (GPEs) prepared by in situ cross-link reaction with different cross-linkers were investigated. The poly(imidazole-co-butylmethacrylate)-based GPE containing the 1,2,4,5-tetrakis(bromomethyl)benzene (B4Br) cross-linker showed a higher ionic conductivity than that containing cross-linkers with a linear structure, due to the formation of micro-phase separation that resulted in an increase in ion transport paths in the GPE. Moreover, the co-adsorbent ((4-pyridylthio) acetic acid, PAA) co-adsorbed with N3 dye on the TiO₂ electrode not only reduced dye aggregation, but also reacted with the cross-linkers in the GPE at the TiO₂/GPE interface. A decrease in the charge transport resistance at the TiO₂/GPE interface was noted after forming the gel; thus the value of J_SC significantly increased from 7.72 to 10.00 mA cm⁻². In addition, in order to reduce the ionic diffusion resistance within the TiO₂ electrode, incorporation of monodispersed PMMA in the TiO₂ paste was considered. With the optimal weight ratio of PMMA/TiO₂ (w/w=3.75), the TiO₂ electrode exhibited larger pores (ca. 350 nm) uniformly distributed after sintering at 500 °C, and the ionic diffusion resistance within the TiO₂ film could significantly be reduced. The cell conversion efficiency increased from 3.61% to 5.81% under illumination of 100 mW cm⁻², an improvement of ca. 55%.     

Surface modification of TiO2 electrode by various over-layer coatings and O2 plasma treatment for dye sensitized solar cells

The anti-recombination property and the surface area of TiO₂ influence the efficiency of dye-sensitized solar cells (DSSCs). The effects of various over-layers and O₂ plasma treatment on TiO₂ electrodes have been investigated. Over-layers were coated by dip coating in a solution of saturated Ba(NO₃)₂, Mg(NO₃)₂ and N₂O₆Sr, which reduced the recombination of electrons from the photo excited state of Ru dye. O₂ plasma treatment was applied to improve both the contact ability with the dye and the electron takeover capability by reducing oxygen vacancies on both the TiO₂ and the over-layer surface. The photo conversion efficiency of DSSC was improved by both over-layer coating and O₂ plasma treatment. In particular, dipping in saturated Ba(NO₃)₂ solution and O₂ plasma treatment (BP), the photo conversion efficiency was greatly improved from 5.27% to 6.76%. The reason was that the over-layers and O₂ plasma treatment decreased electron recombination. The energy barrier of the modified over-layers blocks the electron transfer from TiO₂ to the electrolyte, and consequently increases electron density by extending the electron lifetime. O₂ plasma treatment also increased the Ru dye absorption.     

Enhancement of the photoelectric performance of dye-sensitized solar cells by using a CaCO3-coated TiO2 nanoparticle film as an electrode

Core-shell-type nanoparticles with TiO₂ cores and CaCO₃ shells were applied as the electrode of dye-sensitized solar cells. The performance of the cell was significantly improved (as high as 26.7%) compared to the case when un-coated TiO₂ particle film was used as electrode. The improved energy conversion efficiency has been ascribed to (i) enhanced dye adsorption due to the high isoelectric point of the overlayer, and (ii) the prevention of the back electron transfer by the insulating nature of the overlayer.     

Fabrication of multilayer TiO2 thin films for dye-sensitized solar cells with high conversion efficiency by electrophoresis deposition

This research coats a commercial TiO₂ nanoparticle Degussa P25 with good roundness and size uniformity on an indium tin oxide (ITO) glass substrate and to be photoelectrical electrode by electrophoresis deposition. It combined with dye N719, electrolyte I^-/ and counter-electrode of Pt layer to produce dye-sensitized solar cells (DSSCs). Through the electrophoretic technique, a multilayer film of an appropriate thickness is deposited in the suspension containing TiO₂ nanoparticles and isopropanol. In this process, electric current, voltage, and the number of deposition cycles are well controlled to obtain a single TiO₂ film of around 3.3 μm thick. Stacking is then performed to obtain a multilayer-typed TiO₂ film of around 12 μm thick. As the sintering temperature reaches 400 °C, the prepared multilayer TiO₂ film with a good compactness can increase the dye adsorption capability of the thin film and enhance its adsorption percentage. In addition, the heat treatment will transfer a portion of the rutile crystalline into the anatase crystalline, resulting in better material properties for DSSCs application. DSSCs produced are exposed to metal halide lamp and their energy conversion efficiency is measured. The I-V curve of the produced DSSCs shows that it has an excellent energy conversion efficiency of 6.9%.     

Influences of different TiO2 morphologies and solvents on the photovoltaic performance of dye-sensitized solar cells

The effects of TiO₂ photoelectrode's surface morphology and different solvents on the photovoltaic performance of dye-sensitized solar cells (DSSCs) were studied. By successive coating of TiO₂ suspension, composed of low and high molecular weight poly(ethylene)glycol (PEG) as a binder, double layered TiO₂ photoelectrodes with four different structures were obtained. Among the DSSCs with different TiO₂ electrodes, DSSC with P2P1 electrode (P2 and P1 correspond to PEG molecular weights of 20,000 and 200,000, respectively) showed higher performance under identical film thickness at a constant irradiation of 100 mW cm⁻², which may be correlated with large pore size and high surface area of the corresponding TiO₂ electrode. This was confirmed by electrochemical impedance spectroscopy (EIS) analysis of the DSSC and the transient photovoltage measurement of electrons in the TiO₂ electrode. Among the different solvents investigated here, the DSSC containing acetonitrile showed high conversion efficiency and the order of performance of the DSSCs with different solvents were AN > MPN > PC > GBL > DMA > DMF > DMSO. Better correlation was observed between the donor number of solvents and photoelectrochemical parameters of the DSSCs containing different solvents rather than the measured viscosity and dielectric constant of solvents. The reasons for the low performance of the DSSCs containing DMA, DMSO and DMF, respectively, were due to the negative shift of TiO₂ conduction band and the desorption of dye molecules from the TiO₂ photoelectrode by those solvents.     

Photovoltage enhancement of dye sensitised solar cells by using ZnO modified TiO2 electrode

Abstract

A ZnO modified TiO₂ (ZnO/TiO₂) film was prepared by immersing TiO₂ electrodes in Zn(Ac)₂ aqueous solution. The open circuit voltage of a dye sensitised solar cell (DSSC) with the ZnO/TiO2 film electrode has a dramatic enhancement, compared to the DSSC with the TiO₂ film electrode. However, the short circuit current density of the DSSC with the ZnO/TiO₂ film electrode is lower than that with TiO₂ electrode. The film electrodes were characterised by SEM, EDX and UV-vis, and the photoelectric performance of DSSCs were measured. The photovoltage enhancement is attributed to the formation of a flat-band potential energy barrier by ZnO at TiO₂/electrolyte interface. The decline of the photocurrent with ZnO/TiO₂ film electrode is due to poor dye absorption on larger particles of ZnO.     

Incorporating carbon nanotube in a low-temperature fabrication process for dye-sensitized TiO2 solar cells

Dye-sensitized solar cells (DSSCs) incorporating TiO₂ porous films, prepared at a low temperature (150 °C), along with multi-wall carbon nanotubes (MWCNTs) were studied using two different electrolytes, namely LiI and THI. Electrochemical impedance spectroscopy (EIS) was employed to quantify the charge transport resistance and electron lifetime (τ_e) under different levels (wt%) of MWCNTs and electrolytes. The charge transport resistance at the TiO₂/dye/electrolyte interface (R_ct2) increased as a function of the MWCNT concentration, which ranged 0.1-0.5 wt%, due to a decrease in the surface area and decreased dye adsorption. The characteristic peak shifted to a lower frequency at 0.1 wt% of MWCNT, indicating a longer electron lifetime. The DSSC with the TiO₂ electrode containing 0.1 wt% of MWCNT resulted in a higher short-circuited current density (J_SC) of 9.08 mA/cm², an open-circuit voltage (V_OC) of 0.781 V, and a cell conversion efficiency of 5.02%. EIS was also conducted under dark conditions. The large value at a middle frequency represented electron transport at the TiO₂/dye/electrolyte interface (R_rec). The R_rec for 0.1 wt% MWCNT/TiO₂ was found to be 114 Ω, and for those with 0.3 and 0.5 wt% were 35 and 30 Ω, respectively. The significantly higher value of R_rec suggested that the charge recombination between injected electrons and electron acceptors in the redox electrolyte, I₃⁻, was remarkably retarded. Finally, electrolytes with LiI and THI were used to compare the cell conversion performance under the same conditions. It was found that more electrons were injected in the TiO₂ electrode and the electron recombination reaction was faster in the DSSC with THI than that with LiI.     

Al2O3-coated nanoporous TiO2 electrode for solid-state dye-sensitized solar cell

This paper reports the preparation of a core-shell nanoporous electrode consisting of an inner TiO₂ porous matrix and a thin overlayer of Al₂O₃, and its application for solid-state dye-sensitized solar cell using p-CuI as hole conductor. Al₂O₃ overlayer was coated onto TiO₂ porous film by the surface sol–gel process. The role of Al₂O₃ layer thickness on the cell performance was investigated. The solar cells fabricated from Al₂O₃-coated electrodes showed superior performance to the bare TiO₂ electrode. Under illumination of AM 1.5 simulated sunlight (89 mW/cm²), a ca. 0.19 nm Al₂O₃ overlayer increased the photo-to-electric conversion efficiency from 1.94% to 2.59%.     

Improvement in dye-sensitized solar cells employing TiO2 electrodes coated with Al2O3 by reactive direct current magnetron sputtering

A novel surface modification method was carried out by reactive dc magnetron sputtering to fabricate TiO₂ electrodes coated with Al₂O₃ for improving the performance of dye-sensitized solar cells (DSSCs). The Al₂O₃-coated TiO₂ electrodes had been characterized by X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), UV–vis spectrophotometer, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS). The study results revealed that the modification to TiO₂ increases dye absorption amount, reduces trap sites on TiO₂, and suppresses interfacial recombination. The impact of sputtering time on photoelectric performance of DSSCs was investigated. Sputtering Al₂O₃ for 4 min on 5-μm thick TiO₂ greatly improves all cell parameters, resulting in enhancing the conversion efficiency from 3.93% to 5.91%. Further increasing sputtering time decreases conversion efficiency.     

Thickness effect of RF sputtered TiO2 passivating layer on the performance of dye-sensitized solar cells

We report on the characteristics of a TiO₂ passivating layer grown by radio frequency (RF) magnetron sputtering on F-doped SnO₂ (FTO) electrodes as a function of its thickness. The optical transparency, surface roughness and passivation properties of the TiO₂ layer passivating the FTO electrode depend on the thickness of the TiO₂ passivating layer. In addition, it was found that the power conversion efficiency of the dye-sensitized solar cells (DSSCs) is critically dependent on the thickness of RF sputtered TiO₂ layer inserted between FTO electrode and nanoporous TiO₂ layer. The DSSC fabricated on 50 nm thick TiO₂ passivating FTO electrode showed the maximum power conversion efficiency of 4.42% due to effective prevention of the electron transfer to electrolyte. This indicates that the thickness optimization of the TiO₂ passivating layer is one of the important parameter to obtain high performance DSSCs.     

A technique to compare polythiophene solid-state dye sensitized TiO2 solar cells to liquid junction devices

In this communication, we report on a technique to fabricate solid-state polythiophene-based dye sensitized solar cells (DSSCs) that can be directly compared to analogous liquid junction devices. The device configuration is based on non-porous TiO₂ thin films and one of the three undoped polythiophene hole conductors: poly[3-(11 diethylphosphorylundecyl) thiophene], P3PUT, poly(4-undecyl-2,2′-bithiophene), P4UBT, or poly(3-undecyl-2,2′-bithiophene), P3UBT. These polymers were spin coated and cast from organic solutions onto the TiO₂ films. The dense TiO₂ thin films (ca. 30 nm) were deposited on conductive glass via facile spray pyrolysis and sol–gel techniques. After that, cis-(SCN)₂ Bis(2,2′ bipyridyl-4,4′-dicarboxylate) ruthenium(II) (a.k.a. Ru N3 dye) was adsorbed on the TiO₂ surface, and the polythiophenes were utilized as hole conductors in a simplified solar cell geometry. The results were compared to the control DSSC device made with dense TiO₂ and a liquid electrolyte, or 2,2′,7,7′-tetrakis(N,N-di-p-methoxyphenylamine)-9,9′-spirobifluorene (a.k.a. Spiro-MeOTAD). The polythiophenes exhibited bandgaps in the range 1.9–2.0 eV, and HOMO energy levels of approximately 5 eV (vs. vacuum). The P3PUT DSSC device exhibited an AM1.5 V_OC=0.8 V, a J_SC=0.1 mA/cm², as well as an IPCE=0.5–1%. The AM1.5 short-circuit photocurrents and quantum efficiencies for DSSCs made with the polythiophenes, the Spiro-MeOTAD and the standard liquid electrolyte (I⁻/I₃⁻) were found to be identical within the limits of experimental uncertainty and reproducibility. Our results indicate that a solid-state replacement to the liquid junction is not necessarily limited by the fundamental aspect of hole transfer, one of the three fundamental aspects that must be met for an efficient DSSC. Rather than suggest that P3UBT or P4UBT could be used to create efficient “organic solar cells” with the exclusion of the Ru dye, we suggest that transparent thiophene compounds could be attractive candidates for high-surface area solid-state DSSCs, and that the technique presented can be applied to other hole conductors. It can allow a verification of one of the things necessary for the DSSC, so that parallel studies using high-surface area materials can proceed with confidence.     

Solar photocatalytic degradation of a reactive azo dye in TiO2-suspension

The photocatalytic decolourisation and degradation of an azo dye reactive orange 4 (RO4) in aqueous solution with TiO₂-P25 (Degussa) as photocatalyst in slurry form have been investigated using solarlight. There is a significant difference in adsorption of dye on TiO₂ surface with the change in solution pH. The effect of various photocatalysts such as TiO₂-P25, TiO₂ (anatase), ZnO, CdS, Fe₂O₃, SnO₂ on the decolourisation and degradation has been studied. The order of reactivity of photocatalysts is TiO₂-P25>ZnO>TiO₂ (anatase). CdS, Fe₂O₃ and SnO₂ have negligible activity on RO4 decolourisation and degradation. The effects of various parameters such as catalyst loading, pH and initial concentration of the dye on decolourisation and degradation have been determined. The degradation was strongly enhanced in the presence of electron acceptors such as H₂O₂, (NH₄)₂S₂O₈ and KBrO₃. The effects of dye-assisting chemicals such as Na₂CO₃, NaCl have been carried out. Addition of these chemicals inhibits the removal rate. The photodecolourisation and degradation kinetics are discussed in terms of Langmuir–Hinshelwood kinetic model.     

2-Ethyl-1-hexanol based screen-printed titania thin films for dye-sensitized solar cells

Nanocrystalline titania thin films were prepared by screen printing in order to efficiently control and optimize the main step of the dye-sensitized solar cells (DSSCs) fabrication process. Different compositions of nanocrystalline titanium dioxide screen-printing pastes are described, based on 2-ethyl-1-hexanol solvent and commercial Degussa P25 TiO₂. The rheological properties of the prepared pastes are presented as the crucial parameter of the deposition procedure. The produced titania thin films are extensively characterized by means of spectroscopy (Raman, XRD) and microscopy (SEM, AFM). The performance (induced photon-to-current efficiency—IPCE% and overall energy conversion efficiency—η%) of the corresponding DSSCs is also reported.     

Effect of TiO2 photo-electrode growth condition on dye-sensitised solar cells

Titanium dioxide- (TiO₂) based photo-electrode for dye-sensitised solar cells (DSSCs) use is fabricated with the electro-phoretic deposition (EPD) technique on indium-tin-oxide (ITO). TiO₂ films were synthesised at different EPD biases ranging from 70 to 110 V. We correlate the morphological and optical properties of formed films to the electrical characteristics of fabricated DSSCs. In addition, by neglecting the tunnelling and the tunnelling-assisted thermo-ionic currents with respect to the pure thermo-ionic current at the ITO/TiO₂ interface, we evaluate the high potential barrier, e?_B. Investigation of the electrical properties of the formed DSSCs shows a best result when the TiO₂ film is elaborated at 100 V. Furthermore, by taking into account the high band energy of 0.6 eV at an aluminium-based counter electrode/electrolyte interface, we deduce that aluminium reduces drastically the short-circuit current of the DSSC.     

Influences of water in bis-benzimidazole-derivative electrolyte additives to the degradation of the dye-sensitized solar cells

The chemical stability of dye-sensitized solar cells (DSSC) determines both the cell performance and the cell life-time. The presence of water in the solar cell from surrounding leakage through the imperfection packaging sealants causes the decrease in life-time of photogenerated electrons on the working electrodes, which induces the occurrence of the dark current to the electrolytes and thus leakage current significantly deteriorated the life-time of the DSSC. Reliable electrolyte additives diminishing the influences of water to the DSSCs degradation process becomes a critical issue in maintaining an acceptable cell life-time.In this work, the effects of four benzimidazole derivatives a-d as the electrolyte additives in the presence of water were comprehensively examined by time-dependent photovoltaic performance of the cells. As a result, open-circuit voltage (V_oc), short-circuit current (J_sc), efficiency (η), and fill factor (FF) collected from I-V curves were studied. In addition, electrochemical impedance spectroscopy (EIS) technique was implemented to evaluate the effects of the charge-transfer resistance (R_ct) at the interfaces between TiO₂/dye/electrolyte. Results showed that the bis-benzimidazole derivative c gives significant improvement in the long-term stability due to the effective protection of the ligands between dye and working electrodes from the attack by environmental water molecules.     

Electrodeposition of TiO2/SiO2 nanocomposite for dye-sensitized solar cell

For the working electrode of dye-sensitized solar cell (DSC), TiO₂/SiO₂ nanocomposite materials were electrodeposited on transparent fluorine doped tin oxide-coated glass by cathodic electrodeposition at room temperature. The electrode and DSC fabricated with TiO₂/SiO₂ nanocomposite were characterized with photocurrent density, X-ray diffraction (XRD), field emission-scanning electron microscopy (FE-SEM) and a photovoltaic performance test. On the electrodeposition, the addition of an appropriate amount of SiO₂ in the bath containing TiO₂ slurry was essential to achieve the superior crystallinity, photocurrent density and photovoltaic performance of the resulting TiO₂/SiO₂ electrode, which was significantly superior to a bare TiO₂ electrode. This enhanced performance of optimized TiO₂/SiO₂ electrode was ascribed to the role of SiO₂ as an energy barrier, increasing the physical separation of injected electrons and oxidized dyes/redox couple, and thereby retarding the recombination reactions in the resulting DSC.     

Dye-sensitized solar cells based on anatase TiO2 hollow spheres/carbon nanotube composite films

Dye-sensitized solar cells (DSSCs) based on anatase TiO₂ hollow spheres (TiO2HS)/multi-walled carbon nanotubes (CNT) nanocomposite films are prepared by a directly mechanical mixing and doctor blade method. The prepared samples are characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, UV-vis absorption spectroscopy and N₂ adsorption-desorption isotherms. The photoelectric conversion performances of the DSSCs based on TiO2HS/CNT composite film electrodes are also compared with commercial-grade Degussa P25 TiO₂ nanoparticles (P25)/CNT composite solar cells at the same film thickness. The results indicate that the photoelectric conversion efficiencies (η) of the TiO2HS/CNT composite DSSCs are dependent on CNT loading in the electrodes. A small amount of CNT clearly enhances DSSC efficiency, while excessive CNT loading significantly lowers their performance. The former is because CNT enhance the transport of electrons from the films to FTO substrates. The latter is due to high CNT loading shielding the visible light from being adsorbed by dyes.     

A study on the electron transport properties of TiO2 electrodes in dye-sensitized solar cells

The influences of annealing temperature and different poly (ethylene glycol) (PEG) contents in nano-crystalline TiO₂ electrodes with and without N3 dye on the electron transfer in a dye-sensitized solar cell (DSSC) were investigated. It is found that the power conversion efficiency increases with the increase in annealing temperature and becomes saturated at 400–500 °C, and further increase lowers the performance which is consistent with the enhancement of the crystalline TiO₂ particles observed in X-ray diffraction (XRD) patterns and scanning electron microscopy (SEM) images. Electrochemical impedance spectroscopy (EIS) also confirms this behavior. These results have been further verified by studying the electron lifetimes (τ_e) and electron diffusion coefficients (D_e) of a bare TiO₂ and a dye-sensitized TiO₂ film using a pulsed laser spectrometer. It is noted that both the electron lifetime and the electron diffusion coefficient increase with the increase in annealing temperature. However, the evolution of rutile TiO₂ begins beyond 600 °C and this lowers the dye absorbance and the electron diffusion coefficients of TiO₂ electrodes. A similar study was made by varying the content of the PEG in the TiO₂ films. It is found that with the increase in the PEG content, a decrease in the electron lifetimes and a little hike in the electron diffusion coefficients are noted, where the cell performance remains almost the same. In addition, the dye adsorption decreases the electron lifetime and increases the electron diffusion coefficient of the TiO₂ films regardless of the PEG content and the annealing temperature.