The effect of temperature on corrosion behavior of SS316L in the cathode environment of proton exchange membrane fuel cells

The effect of temperature on the corrosion behavior of SS316L in simulated proton exchange membrane fuel cell (PEMFC) environments has been systematically studied. Electrochemical methods, both potentiodynamic and potentiostatic, are employed to characterize the corrosion behavior. Atomic force microscope (AFM) is used to examine the surface morphology and X-ray photoelectron spectroscopy (XPS) analysis is used to identify the composition and the depth profile of the passive film. Photo-electrochemical (PEC) measurements are also performed to determinate the band gap energy of the passive film semiconductor. Interfacial contact resistances (ICR) between polarized SS316L and carbon paper are also measured. The experimental results show that corrosion resistance decreases with temperatures even though the thickness of passive film increases with temperature, at a given cell potential, the corrosion behavior of SS316L can be significantly different at different temperatures in PEMFC cathode environments, and the band gap of passive films decrease with temperature. The results also show that within the temperature range studied (25-90 °C), after different passivation time, the corrosion current densities of SS316L are all lower than the US DOE 2015 target value of 1 μA cm⁻², but the ICR between the carbon paper and polarized SS316L does not satisfy the US DOE 2015 target.     

Influence of fluoride ions on corrosion performance of 316L stainless steel as bipolar plate material in simulated PEMFC anode environments

Corrosion performance of 316L stainless steel as a bipolar plate material in proton exchange membrane fuel cell (PEMFC) is studied under different simulated PEMFC anode conditions. Solutions of 1 × 10⁻⁵ M H₂SO₄ with a wide range of different F⁻ concentrations at 70 °C bubbled with hydrogen gas are used to simulate the PEMFC anode environments. Electrochemical methods, both potentiodynamic and potentiostatic, are employed to study the corrosion behavior. Scanning electron microscope (SEM) and atomic force microscope (AFM) are used to examine the surface morphology of the specimen after it is potentiostatic polarized in simulated PEMFC anode environments. X-ray photoelectron spectroscopy (XPS) analysis is used to identify the compositions and the depth profile of the passive film formed on the 316L stainless steel surface after it is polarized in simulated PEMFC anode environments. Mott–Schottky measurements are used to characterize the semiconductor passive films. The results of potentiostatic analyses show that corrosion currents increase with F⁻ concentrations. SEM examinations show that no localized corrosion occurs on the surface of 316L stainless steel and AFM measurement results indicate that the surface topography of 316L stainless steel becomes slightly rougher after polarized in solutions with higher concentration of F⁻. From the results of XPS analysis and Mott–Schottky measurements, it is determined that the passive film formed on 316L stainless steel is a single layer n-type semiconductor.     

Corrosion characteristics of SS316L as bipolar plate material in PEMFC cathode environments with different acidities

The corrosion characteristics of SS316L in simulated proton exchange membrane fuel cell (PEMFC) environments with a wide range of H₂SO₄ concentrations have been systematically studied. Electrochemical methods, both potentiodynamic and potentiostatic, are employed to determine the corrosion parameters and the results show that corrosion resistance decreases with increasing H₂SO₄ concentrations. Scanning electron microscope (SEM) is used to examine the surface morphology of the specimens after potentiostatic polarized in simulated PEMFC cathode environments and the results indicate that local corrosion occurs under all the conditions studied and local corrosion is more severe with higher H₂SO₄ concentrations. Auger electron spectroscopy (AES) analysis is used to identify the composition and the depth profile of the passive film formed on the SS316L surface and the results show that the thickness of passive film decreases with increasing H₂SO₄ concentrations. Interfacial contact resistances (ICR) between SS316L polarized and carbon paper are measured and the results show that ICR decreases with increasing H₂SO₄ concentrations. The corrosion mechanisms of SS316L in PEMFC cathode environments are analysed and discussions on choosing simulated PEMFC cathode corrosion environments for accelerated tests are also provided.     

Corrosion behavior of SS316L in simulated and accelerated PEMFC environments

The electrochemical behavior and change in the passive film formation of SS316L are investigated under polymer electrolyte membrane fuel cell (PEMFC) simulated (pH from 3 to 6 containing F⁻, SO₄²⁻ and Cl⁻ anions) and accelerated conditions (0.5 M and 1 M H₂SO₄ + 2 ppm HF). Potentiodynamic, potentiostatic, and EIS measurements are performed to investigate the electrochemical behavior of the SS316L specimens in both the anode and cathode PEMFC environments. The chemical composition of the passive film, surface topography of the specimens, and degree of metal ion release is characterized by XPS, SEM, and ICP-OES, respectively. The results reveal that the nature of the passive film depends on the pH value, external medium/environment, as well as applied potential during polarization. The corrosion behavior of SS316L is closely related to the chemical composition and structure of the passive film.     

An investigation into nickel implanted 316L stainless steel as a bipolar plate for PEM fuel cell

A nickel-rich layer about 100 μm in thickness with improved conductivity was formed on the surface of austenitic stainless steel 316L (SS316L) by ion implantation. The effect of ion implantation on the corrosion behavior of SS316L was investigated in 0.5 M H₂SO₄ with 2 ppm HF solution at 80 °C by potentiodynamic test. In order to investigate the chemical stability of the ion implanted SS316L, the potentiostatic test was conducted in an accelerated cathode environment and the solutions after the potentiostatic test were analyzed by inductively coupled plasma atomic emission spectrometer (ICP-AES). The results of potentiodynamic test show that the corrosion potential of SS316L is shifted toward the positive direction from −0.3 V versus SCE to −0.05 V versus SCE in anode environment and the passivation current density at 0.6 V is reduced from 11.26 to 7.00 μA cm⁻² in the cathode environment with an ion implantation dose of 3 × 10¹⁷ ions cm⁻². The potentiostatic test results indicate that the nickel implanted SS316L has higher chemical stability in the accelerated cathode environment than the bare SS316L, due to the increased amount of metallic Ni in the passive layer. The ICP results are in agreement with the electrochemical test results that the bare SS316L has the highest dissolution rate in both cathode and anode environments and the Ni implantation markedly reduces the dissolution rate. A significant improvement of interfacial contact resistance (ICR) is achieved for the SS316L implanted with nickel as compared to the bare SS316L, which is attributed to the reduction in passive layer thickness caused by the nickel implantation. The ICR values for implanted specimens increase with increasing dose.     

Anticorrosion properties of Ta-coated 316L stainless steel as bipolar plate material in proton exchange membrane fuel cells

In order to reduce the cost, volume and weight of the bipolar plates used in the proton exchange membrane fuel cells (PEMFC), more attention is being paid to metallic materials, among which 316L stainless steel (SS316L) is quite attractive. In this study, metallic Ta is deposited on SS316L using physical vapor deposition (PVD) to enhance the corrosion resistance of the bipolar plates. Simulative working environment of PEMFC is applied for testing the corrosion property of uncoated and Ta-coated SS316L. X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical methods (potentiodynamic and potentiostatic polarization) are also used for analyzing characteristics of uncoated and Ta-coated SS316L. Results show that, Ta-coated SS316L has significantly better anticorrosion property than that of uncoated SS316L, with corrosion current densities of uncoated SS316L being 44.61 μA cm⁻² versus 9.25 μA cm⁻² for Ta-coated SS316L, a decrease of about 5 times. Moreover, corrosion current densities of Ta-coated SS316L in both simulative anode (purged with H₂) and cathode (purged with air) conditions are smaller than those of uncoated SS316L.     

Chromium nitride/Cr coated 316L stainless steel as bipolar plate for proton exchange membrane fuel cell

Chromium nitride/Cr coating has been deposited on surface of 316L stainless steel to improve conductivity and corrosion resistance by physical vapor deposition (PVD) technology. Electrochemical behaviors of the chromium nitride/Cr coated 316L stainless steel are investigated in 0.05 M H₂SO₄ + 2 ppm F⁻ simulating proton exchange membrane fuel cell (PEMFC) environments, and interfacial contact resistance (ICR) are measured before and after potentiostatic polarization at anodic and cathodic operation potentials for PEMFC. The chromium nitride/Cr coated 316L stainless steel exhibits improved corrosion resistance and better stability of passive film either in the simulated anodic or cathodic environment. In comparison to 316L stainless steel with air-formed oxide film, the ICR between the chromium nitride/Cr coated 316L stainless steel and carbon paper is about 30 mΩ cm² that is about one-third of bare 316L stainless steel at the compaction force of 150 N cm⁻². Even stable passive films are formed in the simulated PEMFC environments after potentiostatic polarization, the ICR of the chromium nitride/Cr coated 316L stainless steel increases slightly in the range of measured compaction force. The excellent performance of the chromium nitride/Cr coated 316L stainless steel is attributed to inherent characters. The chromium nitride/Cr coated 316L stainless steel is a promising material using as bipolar plate for PEMFC.     

An investigation into TiN-coated 316L stainless steel as a bipolar plate material for PEM fuel cells

In order to reduce the cost, weight and volume of the bipolar plates, considerable attention is being paid to developing metallic bipolar plates to replace the non-porous graphite bipolar plates that are in current use. However, metals are prone to corrosion in the proton exchange membrane (PEM) fuel cell environments, which decreases the ionic conductivity of the membrane and lowers the overall performance of the fuel cells. In this study, TiN was coated on SS316L using a physical vapor deposition (PVD) technology (plasma enhanced reactive evaporation) to increase the corrosion resistance of the base SS316L. X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical methods were used to characterize the TiN-coated SS316L. XRD showed that the TiN coating had a face-centered-cubic (fcc) structure. Potentiodynamic tests and electrochemical impedance tests showed that the corrosion resistance of SS316L was significantly increased in 0.5 M H₂SO₄ at 70 °C by coating with TiN. In order to investigate the suitability of these coated materials as cathodes and anodes in a PEMFC, potentiostatic tests were conducted under both simulated cathode and anode conditions. The simulated anode environment was −0.1 V versus SCE purged with H₂ and the simulated cathode environment was 0.6 V versus SCE purged with O₂. In the simulated anode conditions, the corrosion current of TiN-coated SS316L is −4 × 10⁻⁵ A cm⁻², which is lower than that of the uncoated SS316L (about −1 × 10⁻⁶ A cm⁻²). In the simulated cathode conditions, the corrosion current of TiN-coated SS316L is increased to 2.5 × 10⁻⁵ A cm⁻², which is higher than that of the uncoated SS316L (about 5 × 10⁻⁶ A cm⁻²). This is because pitting corrosion had taken place on the TiN-coated specimen.     

Electrochemical behavior of surface treated metal bipolar plates used in passive direct methanol fuel cell

Corrosion resistance performance of SS316L treated by passivation solution was investigated in a simulated environment of the passive direct methanol fuel cell (DMFC). Electrochemical impedance spectroscopic (EIS) test showed that polarization resistance of untreated and treated SS316L were 1191 Ω cm² and 9335 Ω cm², respectively. The above result agreed with the Tafel slope analysis of potentiodynamic polarization curves. Comparing the untreated and treated SS316L in the simulated environment of DMFC anode working conditions, it was observed that the corrosion current density of treated SS316L as estimated by 4000 s potentiostatic test reduced from 38.7 μA cm⁻² to 0.297 μA cm⁻², meanwhile, the current densities of untreated and treated SS316L in cathode working conditions were 3.87 μA cm⁻² and 0.223 μA cm⁻², respectively. It indicated that the treated SS316L should be suitable in both anode and cathode environment of passive DMFCs. The treated SS316L bipolar plates have been assembled in a passive single fuel cell. A peak power density of 1.18 mW cm⁻² was achieved with 1 M methanol at ambient temperature.     

Ni–Cr Co-implanted 316L stainless steel as bipolar plate in polymer electrolyte membrane fuel cells

A Ni–Cr enriched layer about 60 nm thick with improved conductivity is formed on the surface of austenitic stainless steel 316L (SS316L) by ion implantation. The electrochemistry results reveal that a proper Ni–Cr implant fluence can greatly improve the corrosion resistance of SS316L in the simulated PEMFC environment. The samples after the potentiostatic test are also analyzed by XPS and the ICR values are measured. The XPS results indicate that the composition of the passive film change from a mixture of Fe oxides and Cr oxide to a Cr oxide dominated passive film after the potentiostatic test. Hence, the ICR increases after polarization due to depletion of iron in the passive film. Nickel is enriched in the passive film formed in the simulated PEMFC cathode environment after ion implantation thereby providing better conductivity than that formed in the anode one.     

Influence of heat treatment on corrosion behaviors of 316L stainless steel in simulated cathodic environment of proton exchange membrane fuel cell (PEMFC)

The influences of two types of heat-treatments on the corrosion behavior of 316L SS in the simulated cathodic environment of PEMFC, are investigated using potentiodynamic curve, electrochemical impedance spectroscopy (EIS), Mott-Schottky plot and auger electron spectroscopy (AES), respectively. The results show that 316L SS is in the passive state within the potential region from −0.1V_SCE to 0.8V_SCE in the simulated cathodic environment of PEMFC, and a passive film can be formed on 316L SS. The passivity of 316L SS in the simulated cathodic environment of PEMFC firstly increases and then degrades with the increased solid solution temperature or time, and the best passivity corresponds to the solid solution temperature at 1050 °C for 40 min among other solid solution treatments. While 316L SS heat-treated with the solid solution treatment at 1050 °C for 40 min plus aging treatment at 900 °C for 4 h, also has the best passivity in the same solution among other solid solution plus aging treatments. The best corrosion protection, lowest donor density and the highest thickness of the passive film corresponding to the solid solution temperature at 1050 °C for 40 min among other solid solution or solid solution plus aging heat treatments, and this treatment is mostly suitable for improving the anti-corrosion property of 316L SS in the simulated cathodic environment of proton exchange membrane fuel cell (PEMFC).     

Improved anticorrosion properties and electrical conductivity of 316L stainless steel as bipolar plate for proton exchange membrane fuel cell by lower temperature chromizing treatment

The lower temperature chromizing treatment is developed to modify 316L stainless steel (SS 316L) for the application of bipolar plate in proton exchange membrane fuel cell (PEMFC). The treatment is performed to produce a coating, containing mainly Cr-carbide and Cr-nitride, on the substrate to improve the anticorrosion properties and electrical conductivity between the bipolar plate and carbon paper. Shot peening is used as the pretreatment to produce an activated surface on stainless steel to reduce chromizing temperature. Anticorrosion properties and interfacial contact resistance (ICR) are investigated in this study. Results show that the chromized SS 316L exhibits better corrosion resistance and lower ICR value than those of bare SS 316L. The chromized SS 316L shows the passive current density about 3E−7 A cm⁻² that is about four orders of magnitude lower than that of bare SS 316L. ICR value of the chromized SS 316L is 13 mΩ cm² that is about one-third of bare SS 316L at 200 N cm⁻² compaction forces. Therefore, this study clearly states the performance advantages of using chromized SS 316L by lower temperature chromizing treatment as bipolar plate for PEMFC.     

Localised corrosion processes of austenitic stainless steel bipolar plates for polymer electrolyte membrane fuel cells

This research addresses the problem of localised corrosion of stainless steel PEMFC bipolar plates. The susceptibility to pitting and crevice corrosion of austenitic AISI 304 stainless steel has been investigated both by post-mortem microscopic analysis of the end-plates of a laboratory single-cell and by studies of electrochemically corroded stainless steels, in the presence of specially-designed crevice-formers simulating the operating conditions of a PEMFC. This work is based on optical and scanning-electron microscopies as well as potentiostatic and potentiodynamic measurements. The crevice-formers we considered were: Teflon, graphite and AISI 304. The samples, coupled to the crevice-formers have been tested in aqueous solutions containing Cl⁻, SO₄²⁻ and F⁻. From the E-log i plot, the values of corrosion, pitting, crevice and protection potential have been obtained and perfect and imperfect passivity conditions have been identified.     

Effect of plasma nitriding on behavior of austenitic stainless steel 304L bipolar plate in proton exchange membrane fuel cell

A dense and supersaturated nitrogen layer with higher conductivity is obtained on the surface of austenitic stainless steel 304L by the low temperature plasma nitriding. The effect of plasma nitriding on the corrosion behavior and interfacial contact resistance (ICR) for the austenitic stainless steel 304L was investigated in 0.05 M H₂SO₄ + 2 ppm F⁻ simulating proton exchange membrane fuel cell (PEMFC) environment using electrochemical and electric resistance measurements. The experiment results show that the stable passive film is formed after the potentiostatic polarization at the specified anodic or cathodic potentials under PEMFC operation condition, and the plasma nitriding improves slightly the corrosion resistance and decreases markedly the ICR of 304L. The ICR of the plasma nitrided 304L increases after the potentiostatic polarizations for 4 h, and lower than 100 mΩ cm² at the compaction force of 150 N cm⁻².     

Corrosion resistance and interfacial contact resistance of TiN coated 316L bipolar plates for proton exchange membrane fuel cell

TiN coating is successfully deposited on 316L by multi-arc ion plating. Corrosion behavior of TiN coated 316L is studied in 0.05 M H₂SO₄ + 2 ppm F⁻ simulating proton exchange membrane fuel cell (PEMFC) environments using electrochemical method, and interfacial contact resistance (ICR) is measured before and after potentiostatic polarization at operation potential for PEMFC. The TiN coated 316L exhibits promising ICR and improved corrosion resistance in simulated aggressive PEMFC environments. Only general overall corrosion is observed after potentiostatic polarization. Stable passive film has formed on the surface of the TiN coated 316L after potentiostatic polarization at the operation potential and results in a slight increase in the ICR. These results indicate that the TiN coated 316L is a candidate bipolar plate material for PEMFC stacks.     

Conductive amorphous carbon-coated 316L stainless steel as bipolar plates in polymer electrolyte membrane fuel cells

Amorphous carbon (a-C) film about 3 μm in thickness is coated on 316L stainless steel by close field unbalanced magnetron sputter ion plating (CFUBMSIP). The AFM and Raman results reveal that the a-C coating is dense and compact with a small size of graphitic crystallite and large number of disordered band. Interfacial contact resistance (ICR) results show that the surface conductivity of the bare SS316L is significantly increased by the a-C coating, with values of 8.3–5.2 mΩ cm² under 120–210 N/cm². The corrosion potential (E_corr) shifts from about −0.3 V vs SCE to about 0.2 V vs SCE in both the simulated anode and cathode environments. The passivation current density is reduced from 11.26 to 3.56 μA/cm² with the aid of the a-C coating in the simulated cathode environment. The a-C coated SS316L is cathodically protected in the simulated anode environment thereby exhibiting a stable and lower current density compared to the uncoated one in the simulated anode environment as demonstrated by the potentiostatic results.     

Electrodeposition of conductive PAMT/PPY bilayer composite coatings on 316L stainless steel plate for PEMFC application

Stainless steel fulfills most of the requirements as bipolar plates in Proton Exchange Membrane Fuel Cell. However, it undergoes severe corrosion in fuel cell operating condition. This can be resolved by coating the stainless steel with corrosion resistive conducting polymers. In this study, homogeneous and adherent conductive Poly(2-amino-5-mercapto-1,3,4- thiadiazole)/Polypyrrole (PAMT/PPY) mono and bilayer polymer composite coatings are electrosynthesized on 316L SS in 0.5 M H₂SO₄ by cyclic voltammetry and chronopotentiometry. The hydrophobicity and surface morphology of the coatings are analyzed by contact angle and scanning electron microscopy respectively. The polymer coatings are evaluated in 0.5 M H₂SO₄ medium by potentiodynamic polarization and impedance techniques at 25 °C. The polarization results reveal that PAMT on PPY composite coating shifts the E_corr of the 316L SS towards noble direction. The EIS study reveals that the R_f value of PAMT on PPY coating is significantly higher by three orders (x10³ Ωcm²) of magnitude than uncoated 316L SS. The corrosion performance of the coatings in simulated PEMFC environment is investigated by potentiodynamic and potentiostatic studies. Results show that the PAMT on PPY and PPY on PAMT bilayer coatings are stable and increased the corrosion potential by about 410–470 mV and 275–310 mV (SCE) in simulated cathodic and anodic conditions respectively. This investigation reports that the PAMT on PPY bilayer coating is serving as a good physical barrier and protecting the 316L SS against corrosion in PEMFC environment.     

Inductively coupled plasma nitriding of chromium electroplated AISI 316L stainless steel for PEMFC bipolar plate

Chromium electroplated AISI 316L stainless steel was nitrided using inductively coupled plasma (ICP) for application in the bipolar plate of a polymer electrolyte membrane fuel cell (PEMFC). A continuous and thin chromium nitride layer was formed at the surface of the samples after ICP nitriding for 2 h at 400 °C. The interfacial contact resistance (ICR) and corrosion resistance in simulated PEMFC operating conditions were higher than the required values, while they varied with the applied dc bias voltage during the nitriding process. The ICR value decreased with an increase in bias voltage. Potentiodynamic polarization measurements showed that all of the nitrided samples had excellent corrosion resistance with a current density of ∼10⁻⁷ A cm⁻² at the cathode. It was also found that the oxygen content at the surface was not increased after the corrosion test. X-ray diffractometry (XRD), field emission scanning electron microscopy (FE-SEM), and Auger electron spectroscopy (AES) were used to analyze the effect of plasma nitriding.     

Nanocomposite-carbon coated at low-temperature: A new coating material for metallic bipolar plates of polymer electrolyte membrane fuel cells

A nanocomposite-carbon layer is coated onto the surface of 316L stainless steel (SS316) using a beam of accelerated C₆₀ ions at low temperature. The coating is composed of textured graphite nanocrystals ranging in size from 1 to 2 nm, with the graphene plane normal to the coating plane; the nanocrystals are separated by amorphous carbon. This orientation of the graphene layer provides low film resistivity in the direction of the substrate normal. Corrosion resistance tests performed in aggressive anodic and cathodic environments of a polymer electrolyte membrane fuel cell (PEMFC) show that the nanocomposite-carbon coated SS316L exhibits better anticorrosion properties than does bare SS316L. The interfacial contact resistance (ICR) of the nanocomposite-carbon coated SS316L is 12 mΩ cm², which is similar to that of graphite at a compaction force of 150 N cm⁻² and lower than a target of ∼20 mΩ cm². A low value of ICR is maintained even after corrosion tests in aggressive anodic and cathodic environments. The fabricated nanocomposite-carbon coated SS316L exhibits excellent corrosion resistance and low interfacial contact resistance under simulated PEMFC bipolar plate conditions.     

Effect of manufacturing conditions on the corrosion resistance behavior of metallic bipolar plates in proton exchange membrane fuel cells

Metallic bipolar plates are one of the promising alternatives to the graphite bipolar plates in proton exchange membrane fuel cell (PEMFC) systems. In this study, stainless steel (SS304, SS316L, and SS430), nickel (Ni 270), and titanium (Grade 2 Ti) plates with an initial thickness of 51 μm were experimented as bipolar plate substrate materials in corrosion resistance tests. In addition to unformed blanks, SS316L plates were formed with stamping and hydroforming processes to obtain bipolar plates under different process conditions (stamping force, hydroforming pressure, stamping speed, hydroforming pressure rate). These bipolar plates, then, were subjected to corrosion tests, and the results were presented and discussed in detail. Potentiodynamic polarizations were performed to observe corrosion resistance of metallic bipolar plates by simulating the anodic and cathodic environments in the PEMFC. In order to determine the statistical significance of the corrosion resistance differences between different manufacturing conditions, analysis of variance (ANOVA) technique was used on the corrosion current density (I_corr, μA cm⁻²) values obtained from experiments. ANOVA for the unformed substrate materials indicated that SS430 and Ni have less corrosion resistance than the other substrate materials tested. There was a significant difference between blank (unformed) and stamped SS316L plates only in the anodic environment. Although there was no noteworthy difference between unformed and hydroformed specimens for SS316L material, neither of these materials meet the Department of Energy‘s (DOE) target corrosion rate of ≤1 μA cm⁻² by 2015 without coating. Finally, stamping parameters (i.e. speed and force levels) and hydroforming parameters (i.e. the pressure and pressure rate) significantly affected the corrosion behavior of bipolar plates.