A Two‐Compartment Fluidized Bed Reactor for CO2 Capture by Chemical‐Looping Combustion

Chemical‐looping combustion (CLC) is a combustion method for a gaseous fuel with inherent separation of the greenhouse gas carbon dioxide. A CLC system consists of two reactors, an air reactor and a fuel reactor, and an oxygen carrier circulating between the two reactors. The oxygen carrier transfers the oxygen from the air to the fuel. The flue gas from the fuel reactor consists of carbon dioxide and water, while the flue gas from the air reactor is nitrogen from the air. A two‐compartment fluidized bed CLC system was designed and tested using a flow model in order to find critical design parameters. Gas velocities and slot design were varied, and the solids circulation rate and gas leakage between the reactors were measured. The solids circulation rate was found to be sufficient. The gas leakage was somewhat high but could be reduced by altering the slot design. Finally, a hot laboratory CLC system is presented with an advanced design for the slot and also with the possibility for inert gas addition into the downcomer for solids flow increase.     

Simulation of autothermal reforming in a staged‐separation membrane reactor for pure hydrogen production

Steam methane reforming with oxygen input is simulated in staged‐separation membrane reactors. The configuration retains the advantage of regular membrane reactors for achieving super‐equilibrium conversion, but reaction and membrane separation are carried out in two separate units. Equilibrium is assumed in the models given the excess of catalyst. The optimal pure hydrogen yield is obtained with 55% of the total membrane area allocated to the first of two modules. The performance of the process with pure oxygen input is only marginally better than with air. Oxygen must be added in split mode to reach autothermal operation for both reformer modules, and the oxygen input to each module depends on the process conditions. The effects of temperature, steam‐to‐carbon ratio and pressure of the reformer and the area of the membrane modules are investigated for various conditions. Compared with a traditional reformer with an ex situ membrane purifier downstream, the staged reactor is capable of much better pure hydrogen yield for the same autothermal reforming operating conditions.     

Membrane/cryogenic hybrid scheme for argon production from air

A novel membrane/cryogenic hybrid scheme is presented wherein crude argon from a cryogenic air separation unit is fed to an oxygen selective membrane unit to remove a substantial portion of the oxygen. The oxygen enriched permeate from the membrane unit is returned to the crude argon distillation column of the cryogenic air separation process. The non-permeate stream is enriched in argon and can be further purified in a catalytic unit to produce an oxygen-free argon stream. The proposed process makes use of the synergy between the two separation units whereby, the cryogenic unit offers high recovery and the membrane provides purification leading to improved argon recoveries at higher argon concentrations. Calculations show that this process, in conjunction with an oxygen removal catalytic process, provides an economical alternative for the production of pure argon as compared to the conventional process using just a cryogenic unit and a catalytic unit to remove oxygen.     

Actual air separation through poly(aniline‐co‐toluidine)/ethylcellulose blend thin‐film composite membranes

Several multilayer thin‐film composite membranes were fabricated of ethylcellulose (EC) and poly(aniline‐co‐ortho‐toluidine) or poly(ortho‐toluidine) blend as selective thin films and three ultrafiltration membranes with a 10‐ to 45‐nm pore size and 100‐ to 200‐μm thickness as porous supports. The relationships between the actual air‐separation performance through the composite membranes and layer number, composition, casting solution concentration of the thin selective film are discussed. The oxygen‐enriched air (OEA) flux through the composite membranes increases steadily with increasing operational temperature and pressure. The oxygen concentration enriched by the composite membranes appears to decrease with operating temperature, but increases with operating pressure. The actual air‐separation property through the composite membranes seems to remain nearly constant for at least 320 days. The respective highest OEA flux, oxygen flux, and oxygen concentration, respectively, were found to be 4.78 × 10⁻⁵ cm³ (STP)/s · cm², 2.2 × 10⁻⁵ cm³ (STP)/s · cm², and 46% across EC/poly(o‐toluidine) (80/20) blend monolayer thin‐film composite membranes in a single step at 20°C and 650 kPa operating pressure. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 458–463, 2000     

Modeling,Characteristic Analysis and Optimization of an Improved Heat‐Integrated Air Separation Column

Cryogenic air separation as the most important part of an integrated gasification combined cycle is a widely used operation unit for producing large quantities of high‐purity oxygen and nitrogen. However, cryogenic distillation requires a large amount of energy due to the work needed to compress the air feed. An improved heat‐integrated air separation column (HIASC) is proposed. The requirements of high‐purity separation in the industrial cryogenic air separation process are achieved. An optimization model of the heat transfer coefficient (UA), a key parameter in column structure design and operation, is presented. The optimized UA value is obtained within the accepted value range reported in the international open literature, which ensures the practicability of the improved HIASC.     

Computer Simulation of the Performance of a Downer‐Regenerator CFB for the Partial Oxidation of n‐Butane to Maleic Anhydride

A reactor model for a downer‐regenerator circulating fluidized‐bed (CFB) during the partial oxidation of n‐butane to maleic anhydride is presented. Upflow reactors (risers) suffer from severe solids back mixing and gas‐solids‐separation, in comparison down flow reactors exhibit a more uniform gas‐solids flow and reduced backmixing, resulting in narrower residence time distributions. Due to the sensitivity of the VPO catalyst to over‐reduction, downer reactors present an interesting alternative to riser reactors. The reactor models for the downer and the regenerator fluidized‐bed are coupled with reduction and oxidation kinetics for the catalyst, respectively. The influence of the solids residence time distributions for the combined system of both reactors on the oxidation state of the catalyst is explored by a novel newly developed oxygen loading distribution. Simulation results suggest the limited solids‐flux in downers restrict the maximum butane concentrations, while the scale‐up is predicted to be uncritical.     

Influence of Particle Size and Single‐Tube Diameter on Thermal Behavior of Fischer‐Tropsch Reactors. Part II. Eggshell Catalysts and Optimal Reactor Performance

The optimal combination of particle and tube size for simulation of a single tube of a wall‐cooled multitubular Fischer‐Tropsch (FT) reactor with cobalt as catalyst was determined. The maximum size of the tubes, realized without temperature runaway, enhances with increasing particle size until an optimal value is reached, thereby improving the production rate of liquid fuels per tube. Reasons for this are that heat transfer to the cooled tube wall for a given tube size is considerably enhanced by increasing the particle size and that the influence of pore diffusion on the effective rate of FT synthesis gets stronger with rising particle size, which reduces the temperature sensitivity of the reactor and decreases the danger of a temperature runaway. The simulations indicate that the use of FT eggshell catalysts is not an option for fixed‐bed reactors. The temperature sensitivity of the reactor is strongly enhanced, which decreases the maximum tube size and with that the productivity per tube. All these effects are valid in general for wall‐cooled fixed‐bed reactors. Respective criteria are presented.     

Modeling of Multi‐Tubular Reactors for Fischer‐Tropsch Synthesis

The results of the simulation of multi‐tubular Fischer‐Tropsch reactors based on a two‐dimensional pseudo‐homogeneous model are presented. The model takes into account the intrinsic kinetics of two commercial iron and cobalt catalysts, intraparticle mass transfer limitations, and the radial heat transfer within the fixed bed and to the cooling medium (boiling water). The effective rate with Co is slightly higher than with Fe. Hence, a temperature level can be used for Co that is 20 °C lower compared to Fe. The conversion and product selectivies are then almost the same and the reactor can be operated safely without a temperature runaway. The results of the simulations are consistent with literature data and show that there is still room for improvement of fixed bed FT reactors, e.g., by an enhanced heat transfer.     

Production of argon free oxygen by adsorptive air separation on Ag‐ETS‐10

The purification of different components of air, such as oxygen, nitrogen, and argon, is an important industrial process. Pressure swing adsorption (PSA) is surpassing the traditional cryogenic distillation for many air separation applications, because of its lower energy consumption. Unfortunately, the oxygen product purity in an industrial PSA process is typically limited to 95% due to the presence of argon which always shows the same adsorption equilibrium properties as oxygen on most molecular sieves. Recent work investigating the adsorption of nitrogen, oxygen and argon on the surface of silver‐exchanged Engelhard Titanosilicate‐10 (ETS‐10), indicates that this molecular sieve is promising as an adsorbent capable of producing high‐purity oxygen. High‐purity oxygen (99.7+%) was generated using a bed of Ag‐ETS‐10 granules to separate air (78% N₂, 21% O₂, 1% Ar) at 25°C and 100 kPa, with an O₂ recovery rate greater than 30%. © 2012 American Institute of Chemical Engineers AIChE J, 59: 982–987, 2013     

Chemical-looping combustion in a 300 W continuously operating reactor system using a manganese-based oxygen carrier

Chemical-looping combustion (CLC) is a method for the combustion of fuel gas with inherent separation of carbon dioxide. This technique involves the use of two interconnected reactors. A solid oxygen carrier reacts with the oxygen in air in the air reactor and is then transferred to the fuel reactor, where the fuel gas is oxidized to carbon dioxide and water by the oxygen carrier. Fuel gas and air are never mixed and pure CO₂ can easily be obtained from the flue gas exit. The oxygen carrier is recycled between both reactors in a regenerative process. This paper presents the results from a continuously operating laboratory CLC unit, consisting of two interconnected fluidized beds. The feasibility of the use of a manganese-based oxygen carrier supported on magnesium stabilized zirconia was tested in this work. Natural gas or syngas was used as fuel in the fuel reactor. Fuel flow and air flow was varied, the thermal power was between 100 and 300 W, and the air ratio was between 1.1 and 5.0. Tests were performed at four temperatures: 1073, 1123, 1173 and 1223 K. The prototype was successfully operated at all conditions with no signs of agglomeration or deactivation of the oxygen carrier. The same particles were used during 70 h of combustion and the mass loss was 0.038% per hour, although the main quantity was lost in the first hour of operation. In the combustion tests with natural gas, methane was detected in the exit flue gases, while CO and H₂ were maintained at low concentrations. Higher temperature or lower fuel flows increases the combustion efficiency, which ranged from 0.88 to 0.99. On the other hand, the combustion of syngas was complete for all experimental conditions, with no CO or H₂ present in the gas from the fuel reactor.     

A thermal‐flywheel approach to distributed temperature control in microchannel reactors

Microchannel reactors are a promising route for monetizing distributed natural gas resources. However, intensification and miniaturization represent a significant challenge for reactor control. Focusing on autothermal methane‐steam reforming reactors, a novel microchannel reactor temperature control strategy based on confining a layer of phase‐change material (PCM) between the reactor plates is introduced. Melting‐solidification cycles, which occur with latent heat exchange at constant temperature, allow the PCM layer to act as an energy storage buffer—a “thermal flywheel”—constituting a distributed controller that mitigates temperature excursions caused by fluctuations in feedstock quality. A novel stochastic optimization algorithm for selecting the PCM layer thickness (i.e., distributed controller “tuning”) is introduced. Furthermore, a hierarchical control structure, whereby the PCM layer is complemented by a supervisory controller that addresses persistent disturbances, is proposed. The proposed concepts are illustrated in a comprehensive case study using a detailed two‐dimensional reactor model. © 2013 American Institute of Chemical Engineers AIChE J, 59: 2051–2061, 2013     

Simulation and thermodynamic analysis of conventional and oxygen permeable CPO reactors

A one-dimensional steady-state heterogeneous model has been used to simulate the conventional CPO reactor. With the mechanism of O₂ permeable membrane, the model has been developed to simulate O₂ membrane reactor. The output temperature and the mole flow rates of different species in the tube side and the shell side can be calculated. They are the basis for the exergy analysis of the conventional CPO reactor with air, the conventional CPO reactor with pure O₂, and the O₂ permeable membrane CPO reactor. The simulation and exergy analysis results indicate that when the inlet conditions are the same, for a given methane conversion, the exergy efficiencies η₂ and η₁ of conventional CPO reactor with pure oxygen is lowest among the three reactors, because of the large amount of accumulative exergy required for obtaining pure oxygen.The exergy efficiencies η₁ and η₂ of membrane reactor are comparable with conventional CPO reactor with air and much higher than conventional CPO reactor with pure oxygen. As the membrane reactors can carry out simultaneous separation and reaction, in the mean time, removal of nitrogen from the product stream can be accomplished; the membrane reactor has advantages compared to other types of reactors.The operation of the membrane CPO reactor is more favourable when the inlet temperature is increased and the operation pressure is decreased from a thermodynamic point of view.     

Production of optically pure L‐valine in fluidized and packed bed reactors with immobilized L‐aminoacylase

A process to obtain L ‐valine has been developed using fluidized and packed bed reactors with L ‐aminoacylase (from hog kidney) immobilized by covalent binding. L ‐Valine production using the immobilized derivative of L ‐aminoacylase in fluidized and packed bed reactors was studied at three different substrate concentrations and two different flow rates. Higher productions were obtained in the packed bed reactor in all cases. The different solubilities of L ‐valine and acetyl‐D ‐valine in ethanol were used to purify L ‐amino acid from the reactor effluents. The amount of added ethanol did not influence the separation yields, although the purity of L ‐valine was strongly affected by this parameter. The last step involved was racemization of the unhydrolyzed acetyl‐D ‐valine, which was then used as substrate in a new reaction cycle. © 1999 Society of Chemical Industry     

Techno‐Economic Comparison of a 7‐MWth Biomass Chemical Looping Gasification Unit with Conventional Systems

The chemical looping process is an alternative method to provide conventional gasification (CG) systems with the required oxygen. The syngas produced via chemical looping has a higher calorific value than that generated by a conventional process with air. For comparison, a conventional gasification unit with pure oxygen (CGPO) and a chemical looping gasification (CLG) system were simulated with Aspen Plus. The CGPO reactor consisted of a bubbling fluidized bed and sand as bed material with oxygen supplied via a pressure swing adsorption unit. The CLG comprised a bubbling fluidized‐bed gasifier working in parallel with a fast fluidized‐bed oxidizer. The total capital investment (TCI) of the CLG unit was higher than that of the CGPO unit but the annual operating cost of the former was less which repays the difference in TCI in less than six years.     

Modeling,simulation, and optimization of multiproduct cryogenic air separation unit startup

The startup of multiproduct cryogenic air separation plants takes several hours, during which time limited revenue is generated with high costs incurred due to the highly energy-intensive nature of these operations. This motivates the development of high-fidelity dynamic models to capture the complexity of the startup process to aid decision-making. This article focuses on the development of a startup model for a multiproduct air separation unit (ASU), and its use in dynamic simulation and optimization. To accomplish this, a first-principles based dynamic ASU model is extended by including various discontinuities using smooth approximations, adding dynamics to the primary heat exchanger, and extending the handling phase change within process streams. Dynamic simulations demonstrate plant response behavior during startup, including a failed startup resulting from an injudicious choice of input trajectory. In addition, improvement of startup operation is demonstrated through the incorporation of the model within a dynamic optimization framework.     

Characterization and Modeling of Oxygen Transfer in a Spouted‐Bed Reactor with Auxiliary Aeration

A draft‐tube spouted‐bed (DTSB) reactor was equipped with an auxiliary aeration device to provide air into the annular region and thereby improve the oxygen transfer efficiency. The effects of the total air flow rate and its distribution between spout and annulus, the liquid phase viscosity (water and carboxymethyl cellulose solutions), and the solid holdup (glass and cyclodextrin polymer beads) on the oxygen transfer efficiency were discussed. The oxygen transfer coefficient increased with the air flow rate and the ratio of air flowing through the annulus, whereas it decreased with increasing viscosity and solid holdup. A correlation was proposed to predict the transfer coefficient in DTSB reactors with primary and auxiliary aeration. A good fitting was achieved between the experimental data and those estimated with the model.     

Oxygen enrichment from air through multilayer thin low‐density polyethylene films

Several multilayer thin low‐density polyethylene (LDPE) films were fabricated by blown thin film having a thickness of 7 μm and an area of 130 cm². They were characterized for their oxygen‐enrichment performance from air by a constant pressure–variable volume method in a round permeate cell with an effective area of 73.9 cm². The relationship between oxygen‐enrichment properties, including oxygen‐enriched air (OEA) flux, oxygen concentration, permeability coefficients of OEA, oxygen, nitrogen, as well as separation factor through the multilayer LDPE films, and operating parameters, including transfilm pressure difference, retentate/permeate flux ratio, temperature, as well as layer number, are all discussed in detail. It is found that all of the preceding oxygen‐enrichment parameters increase continuously with an increase of transfilm pressure difference from 0.1 to 0.65 MPa, especially for the trilayer and tetralayer LDPE films. The oxygen concentration and separation factor appear to rapidly increase within the retentate/permeate flux ratio below 200, and then become unchangeable beyond that, whereas the OEA flux and the permeability coefficients of OEA, oxygen, and nitrogen seem to remain nearly constant within the whole retentate/permeate flux ratio investigated, especially for the monolayer and bilayer LDPE films. The selectivity becomes inferior, whereas the permeability becomes superior, as the operating temperature increases from 23 to 31°C. The highest oxygen concentration was found to be 44.8% for monolayer LDPE film in a single step with air containing oxygen of 20.9% as a feed gas and operating pressure of 0.5 MPa at a retentate/permeate flux ratio of 340 and 23°C. The results demonstrate a possibility to prepare an oxygen‐enriching membrane directly from air, based on the easily obtained thin LDPE films. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 3013–3021, 2002; DOI 10.1002/app.2331     

Fixed‐Bed Multi‐Tubular Reactors for Oxidative Dehydrogenation in Ethylene Process

An industrial‐scale reactor for ethylene production was modeled using the oxidative dehydrogenation of ethane (ODHE) in a multi‐tubular reactor system, examining a variety of parameters affecting reactor performance. The model showed that a double‐bed multi‐tubular reactor with intermediate air injection scheme was superior to a single‐bed design, due to the increased ethylene selectivity while operating under lower oxygen partial pressures. The optimized reactor length for 100 % oxygen conversion was theoretically determined for both reactor designs. The use of a distributed oxygen feed with a limited number of injection points indicated a significant improvement on the reactor performance in terms of ethane conversion and ethylene selectivity. This concept also overcame the reactor runaway temperature problem and enabled operations over a wider range of conditions to obtain enhanced ethylene production.     

天然气制氢反应器的研究进展

氢是一种理想的能源,高纯氢的制备是近年研究的一个重点,反应器的结构是制氢的关键。本文综述了固定床、流化床、膜反应器、等离子体反应器、太阳能反应器和微通道反应器在甲烷制氢研究中的应用,分析了各种反应器在制氢过程的特点以及不足之处,指出了制氢反应器的发展方向。     

Optimal design and integration of an air separation unit (ASU) for an integrated gasification combined cycle (IGCC) power plant with CO2 capture

The air separation unit (ASU) plays a key role in improving the efficiency, availability, and operability of an oxygen-fed integrated gasification combined cycle (IGCC) power plant. An optimal integration between the ASU and the balance of the plant, especially the gasifier and the gas turbine (GT), has significant potential for enhancing the overall plant efficiency. Considering the higher operating pressure of the GT, an elevated-pressure air separation unit (EP-ASU) is usually favored instead of the conventional low-pressure air separation units (LP-ASU). In addition, a pumped liquid oxygen (PLOX) cycle is usually chosen if the operating pressure of the gasifier is high. A PLOX cycle helps to improve plant safety and availability and to decrease the capital cost by reducing the size of the oxygen compressor or by eliminating it completely. However, the refrigeration lost in withdrawn liquid oxygen must be efficiently recovered. This paper considers five different configurations of an ASU with PLOX cycle and compares their power consumptions with an EP-ASU with a traditional gaseous oxygen (GOX) cycle. The study shows that an optimally designed EP-ASU with a PLOX cycle can have similar power consumption to that of an EP-ASU with GOX cycle in the case of 100% nitrogen integration. In the case of an IGCC with pre-combustion CO₂ capture, the lower heating value (LHV) of the shifted syngas, both on a mass and volumetric basis, is in between the LHV of the unshifted syngas from an IGCC plant and the LHV of natural gas, for which the GTs are generally designed. The optimal air integration in the case of a shifted syngas is found to be much lower than that of an unshifted syngas. This paper concurs with the existing literature that the optimal integration occurs when air extracted from the GT can be replaced with the nitrogen from the ASU without exceeding mass/volumetric flow limitations of the GT. Considering nitrogen and air integration between the ASU and the GT, this paper compares the power savings in an LP-ASU with a PLOX cycle to the power savings in an EP-ASU with GOX cycle and EP-ASU with PLOX cycle. The results show that an LP-ASU with a PLOX cycle has less power consumption if the nitrogen integration levels are less than 50-60%. In addition, a study is carried out by varying the concentration of nitrogen and steam in the fuel diluents to the GT while the NOx level was maintained constant. The study shows that when the nitrogen injection rate exceeds 50%, an EP-ASU with a PLOX cycle is a better option than an LP-ASU with a PLOX cycle. This paper shows that an optimal design and integration of an ASU with the balance of the plant can help to increase the net power generation from an IGCC plant with CO₂ capture.