共查询到18条相似文献,搜索用时 140 毫秒
1.
通过力学性能对比试验,研究硅钛复合氧化物对PP老化性能的影响。结果表明,硅钛复合氧化是一种性能优异的PP抗老化剂。 相似文献
2.
稀土偶联剂对PP/CaCO3复合材料老化性能的影响 总被引:3,自引:0,他引:3
通过高分子材料自然老化实验前后力学性能的变化,研究了稀土偶联剂WOT对PP/CaCO3复合体系的老化性能的影响。研究结果表明,无机粒子经WOT处理后,体系的力学性能和老化性能均有一定程度的提高。老化180d后,经WOT处理的PP/CaCO3复合体系拉伸强度均高于未经WOT处理的体系,冲击强度均高于纯PP。在高填充情况下,WOT用量高的体系的冲击强度在整个老化过程中一直较高,老化180d后,其冲击强度是PP的1.8~2.4倍,性能保持率可达55%~74%。可以看出,WOT处理无机粒子不会加速PP的自然老化。 相似文献
3.
采用熔融共混的方法制备了聚丙烯(PP)/稀土铝酸锶复合材料,研究了稀土铝酸锶用量对PP/稀土铝酸锶复合材料结晶性能、力学性能和光学性能的影响。结果表明,稀土铝酸锶的加入没有改变PP的晶型;稀土铝酸锶起异相成核作用,结晶度随着稀土铝酸锶含量的增加有不同程度的增加,与PP相比,复合材料的球晶尺寸细小而均匀;PP/稀土铝酸锶复合材料的拉伸强度和断裂伸长率均随着稀土铝酸锶含量的增加出现先增大后减小的趋势;随着稀土铝酸锶含量的增加,复合材料的初始光强度逐渐增大,而发光强度衰减曲线均呈指数规律衰减。 相似文献
4.
将熔融浸渍制备的长玻璃纤维(LGF)增强聚丙烯(PP)与PP按照不同比例熔融共混,制备了不同LGF含量的LGF增强PP复合材料。研究了老化时间、LGF含量对LGF增强PP复合材料力学性能的影响。结果表明:随着LGF含量的增加,LGF增强PP复合材料的断裂伸长率稍有下降,拉伸强度、弯曲强度、弯曲模量、冲击强度及缺口冲击强度都显著提高。老化时间的延长,对低LGF含量的LGF增强PP复合材料的力学性能影响不大;老化时间较长时,高LGF含量的LGF增强PP复合材料的总体力学性能有所下降。 相似文献
5.
6.
聚丙烯/纳米TiO2复合材料的紫外老化研究 总被引:2,自引:0,他引:2
对聚丙烯(PP)/纳米TiO2复合材料的紫外老化进行了研究。力学性能、熔体粘度、熔融温度、红外光谱和扫描电镜对比试验的结果表明:PP/纳米TiO2复合材料的耐紫外老化性能比纯PP的大大提高,纳米TiO2是一种性能优异的PP抗老化剂。 相似文献
7.
8.
9.
10.
采用聚丙烯-丙烯腈接枝共聚物(PP-g-AN)、有机化纳米二氧化钛(TiO2)对聚丙烯(PP)进行抗老化改性,并通过加速老化测试仪、扫描电子显微镜、紫外-可见光谱仪等仪器测试表征了老化后共混物的变化情况,并测试了加速老化500、1000、1500、2000、2500h后纯PP和PP/PP-g-AN/纳米TiO2的力学性能。结果表明,PP/PP-g-AN/纳米TiO2经过加速老化后具有良好的抗老化性能,当PP/PP-g-AN/纳米TiO2含量为90/5/5时(简称G5T5),加速老化2500h后PP/PP-g-AN/纳米TiO2的拉伸强度达到最大值25.58MPa,冲击强度为62.73kJ/m2;加入改性材料能够有效提高PP的抗老化性能,延长PP的使用时间。 相似文献
11.
A study has been made of the crystallization behavior of polypropylene (PP) filled with rare earth oxides under isothermal conditions. These rare earth oxides include lanthanum oxide (La2O3), yttrium oxide (Y2O3), and a mixture of rare earth oxides containing 70% Y2O3 (Y2O3–0.70). A differential scanning calorimeter was used to monitor the energetics of the crystallization process from the melt. During isothermal crystallization, dependence of the relative degree of crystallinity on time was described by the Avrami equation. It has been shown that the addition of any of the three rare earth oxides causes a considerable increase in the overall crystallization rate of PP but does not influence the mechanism of nucleation and growth of the PP crystals. The analysis of kinetic data according to nucleation theories shows that the increase in crystallization rate of PP in the composites is due to the decrease in surface energy of the extremity surfaces. The relative contents of the β-form in the composites are somewhat higher than that in the plain PP. However, the contents of the β-form in the plain PP and the composites are all very low relative to those of the β-form and the influence of the formation of the β-form on the crystallization kinetics can be neglected. © 1993 John Wiley & Sons, Inc. 相似文献
12.
采用氙灯人工加速老化的方法,研究了以复配型1#耐候助剂制备的耐候母粒对聚丙烯薄膜耐候性能的影响。结果表明:复配型1#耐候助剂对PP薄膜具有很好的耐候效果,以其制备的PP耐候母粒的最佳用量为5%,且钙母粒的加入对添加5%耐候母粒的PP薄膜耐候性能影响很小。 相似文献
13.
稀土偶联剂(REC)对PP/Mg(OH)2体系性能的影响 总被引:16,自引:2,他引:14
研究了稀土偶联剂(REC)处理对PP/氢氧化镁(Mg(OH)2)体系的燃烧性能、流动性能、力学性能及老化性能的影响。未经处理的Mg(OH)2在填充量超过50%时,PP/Mg(OH)2体系的OI≥28.5,但这时冲击强度不足纯PP的30%,熔体流动速率低于0.6g/10min;而填料用2.5%(重量)REC处理后,填充量为50%的体系冲击强度接近纯PP,MFR达2.8g/10min;REC对Mg(O 相似文献
14.
15.
16.
17.
稀土铝酸锶发光聚合物复合材料是目前应用最广泛的发光材料,可用于制备海洋用夜光纤维,有望解决深海、黑暗条件的水下作业难题。将稀土铝酸锶发光材料(SrAl2O4∶Eu2+,Dy3+)与热塑性弹性体PP进行混合,再通过螺杆挤出纺丝机制备了SrAl2O4∶Eu2+,Dy3+质量分数为2%、5%、10%和15%的聚丙烯夜光纤维。研究了不同质量分数的稀土铝酸锶对夜光纤维的结晶性能、荧光性能以及力学性能的影响。结果表明,稀土铝酸锶的加入没有破坏PP的晶体结构,并起到了异相成核的作用,且随着其质量分数增加,异相成核的作用越来越明显;当稀土铝酸锶质量分数为5%时,熔融焓与结晶度最大;稀土铝酸锶的质量分数越高,吸光储能效果越好,发光强度也就越大;夜光纤维的拉伸断裂强度随稀土铝酸锶质量分数的增加而逐渐降低,断裂伸长率在其质量分数为5%时出现最大值。 相似文献
18.
《Ceramics International》2020,46(4):4444-4453
In order to study the variation of rare earth oxides during thermal failure of thermal barrier coatings, Eu2O3-doped YSZ coatings with 0.5 mol%, 1.0 mol% and 1.5 mol% were prepared by explosive spraying. SEM, XRD, EDS and microhardness tester were used to analyze the effect of different rare earth oxide doping content on the morphology, composition and mechanical properties of the coatings. The results showed that with the increase of rare earth oxide doping content, the porosity of the coatings decreased, and the microhardness and fracture toughness increased. When the doping amount of rare earth oxide is 1.0 mol%, the bonding strength and thermal cycle times of the coating are the highest, 33.4 Mpa and 185 times respectively. With the increase of the doping amount of rare earth, the luminous intensity of the sprayed coating increases. After thermal shock test, the luminous intensity of Eu2O3-doped YSZ coatings at 592 and 608 nm decreased to a certain extent. 相似文献