共查询到19条相似文献,搜索用时 140 毫秒
1.
耐磨复合磷化的研究 总被引:3,自引:1,他引:2
传统的磷化膜主要用于耐腐蚀.主要研究一种耐磨性磷化膜,目的是提高磷化膜的耐磨性,使磷化膜可以作为一种固体润滑膜独立使用.按磷化的成膜机理,设计了耐磨复合磷化液配方.研究了磷化液主要成分的含量、温度、时间、酸比等工艺参数对磷化成膜的影响,并研究了复合磷化膜的耐磨性.结果表明:最佳磷化工艺为20g/L Zn(NO3)2、60g/L日夫盐、15g/L Mn(NO3)2、2g/L Ni(NO3)2、2g/L Ca(NO3)2、1g/L酒石酸,少量添加剂,温度60~70℃,时间10~15min.复合磷化膜为深灰黑色,细密针状结晶,孔隙分布均匀.磷化前的表面调整能提高磷化质量.复合磷化膜能有效降低摩擦副表面的摩擦因数,从原来的0.8降到0.2.提高了耐磨性. 相似文献
2.
3.
为了对机电设备及零部件的局部磷化,研制了一种用擦涂方法进行磷化的磷化液,分析讨论了复合促进剂对磷化成膜速度和磷化膜性能的影响.该磷化液游离酸度稳定、常温下操作、工艺简单.磷化膜层致密耐蚀且厚度均匀、可调,外观呈银白或银灰色.可用作耐磨、耐蚀膜层,也可用作有机涂层的基底. 相似文献
4.
超声波对磷化成膜的促进使用 总被引:6,自引:0,他引:6
施加超声波可以促进磷化成膜。促进作用包括三个方面,成膜速度加快、常温处理、无需活化。采用 SEM 和常规耐蚀试验比较了施加超声波前后锌系磷化膜结构和性能。施加超声波后形成的锌系磷化膜结晶更致密、耐蚀性也好。而且施加超声波后磷化溶液成分宽容度更大,工艺更易控制。 相似文献
5.
常温钢铁磷化处理的研究 总被引:3,自引:0,他引:3
用正交试验法优选了磷化配方,通过金相显微镜观察优化后的磷化膜,其金相结构致密、连续.电化学方法测试成膜过程,其极化曲线表明,磷化成膜后,腐蚀电流基本保持不变.利用X射线光电子能谱(XPS)测定膜表面的元素组成,由Zn、Fe、P的不同峰值的能谱、O的能谱峰及俄歇能谱同时存在,可说明磷化膜主要是由Fe及Zn的多种磷酸盐构成.同时,技术性能测试表明,该磷化液溶液稳定、沉渣少、成膜速度快且磷化膜耐蚀性能好. 相似文献
6.
7.
8.
常温快速磷化剂的研究 总被引:8,自引:2,他引:6
研制了一种锌系常温快速磷化液,考察了复合促进剂所含物质对磷化液磷化效果的影响,同时讨论了如何提高磷化成膜速度和磷化膜的耐蚀性等问题,并指出了工艺上的改进. 相似文献
9.
10.
通过实验讨论了铁系磷化液的研制配方、磷化成膜的影响因素及磷化膜的性能。结果表明,铁系磷化液使用过程中无沉渣,铁系磷化膜的膜层重量为1.2g/m2,柔韧性为1mm,耐硫酸铜点滴实验3min以上。同时发现,试验配方在磷化成膜过程中能形成柔韧性好、耐蚀性强的铁系薄层磷化膜,该膜在阴极电泳过程中溶解性小。 相似文献
11.
12.
13.
14.
15.
16.
17.
R. V. Moshtev 《工业材料与腐蚀》1967,18(11):978-983
Zinc phosphate coatings from supersaturated baths The author studied the properties of supersaturated phosphating solutions containing zinc phosphate being used for phosphating steel. The study included the influence of the solution variables, and in particular of the ferrous ion concentration, on the supersaturation and the coating properties. The accelerating effect of supersaturation is so strong that heavy, dense, and fine grain coatings are obtained without oxidants and at temperatures as low as + 10° C. Some aspects of the kinetics and the mechanism of coating formation in supersaturated solutions are discussed. Supersaturated phosphating solutions with zinc phosphate may find practical application, particularly where a high degree of protection is desired. 相似文献
18.
Zinc phosphate coating was formed on 6061-Al alloy through a phosphating bath containing mainly ZnO, H3PO4, NaF. Yttrium oxide (Y2O3) was used as an accelerator of phosphatization to replace nitrite. The morphology, composition and the growth process of the zinc phosphate coating were investigated by SEM, EDX, XRD, FTIR and electrochemical measurements. The phosphate coating formed is composed of hopeite and metallic zinc. The formation and morphology of the zinc phosphate coating were strongly influenced by the presence of yttrium oxide (Y2O3) in the phosphating bath. The formed zinc phosphate coatings exhibited high corrosion resistance in 3% NaCl solution as shown by polarization measurement. 相似文献
19.
通过比较三种前处理方法对所研制的固态防腐耐磨剂耐蚀性的影响,发现磷化前处理不仅能提高涂层与基体材料的结合力,而且也增强了涂层的耐蚀性,同时研究了磷化参数对涂层耐蚀性的影响。 相似文献