Synthesis of nanocrystalline TiO<Subscript>2</Subscript>-coated coal fly ash for photocatalyst

In order to more easily separate TiO₂ photocatalyst from treated wastewater, TiO₂ photocatalyst is immobilized on coal fly ash by precipitation method. The titanium hydroxide precipitated on coal fly ash by neutralization of titanium chloride is transformed into titanium dioxide by heat treatment in the temperature range of 300–700 ‡C. The crystalline structure of the titanium dioxide shows anatase type in all ranges of heat treatment temperature. The crystal size of anatase increases with increasing heat treatment temperature, with the drawback being the lower removal ability of NO gas. When the coal fly ash coated with 10 wt% of TiO₂ was calcined at 300 and 400 ‡C for 2 hrs, the average crystal size of anatase appeared about 9 nm, and the removal rates of NO gas were 63 and 67.5%, respectively. The major iron oxide, existing in coal fly ash as impurity, is magnetite (Fe₃O₄). Phase transformation of magnetite into hematite (Fe₂O₃) by heat treatment improves the removal rate of NO gas for TiO₂-coated coal fly ash.     

Synthesis and characterization of porous TiO<Subscript>2</Subscript> with wormhole-like framework structure

A fast and reliable synthetic route for preparing contaminant-free porous TiO₂ with a wormhole-like framework and close packed macropores is demonstrated based on a sol-gel process involving acid hydrolysis of an alkoxide in the presence of a cationic surfactant. Powder X-ray diffraction (XRD) and transmission electron microscopy (TEM) measurements have been used to characterize the porous structure and the crystallinity. The XRD patterns, TEM and scanning electron microscopy (SEM) images confirm that these materials have disordered wormhole-like topology with close-packed nearly hexagonal macropores. The mesopore diameters and surface area of titanium dioxide, evaluated from the N₂-sorption isotherms, indicate average pore diameters of about 7 and 6 nm and surface areas of about 100 and 335 m²/g, for as-prepared and calcined samples at 400°C.     

Adsorption of thallium cations on RuO<Subscript>2</Subscript>–TiO<Subscript>2</Subscript> electrodes

The electrochemical ion-exchange properties of RuO₂–TiO₂ film electrodes with different composition have been studied in acidic and alkaline media. Thallium-cation uptake has been observed only from the latter and its extent was found to be a function of electrode potential and composition. At potentials near 0.0 V (RHE), the amount of adsorbed Tl⁺ exhibited a maximum, and decreased with increasing potential, reaching a broad minimum in the range 0.4–0.8 V. A further increase in the electrode potential, above about 1.0 V, led to an increase of adsorbed thallium species, essentially due to deposition of a few layers of Tl(III) hydroxide. In fact, the release of the latter species was found to be much slower than that of thallium ions adsorbed at 0.0 V. For the latter, in turn, the double injection/ejection mechanism, currently accepted to explain the charge-storage in oxide electrodes, seems to be confirmed. The high Γ values attained at 0.0 V indicate that the large ionic radius of Tl⁺ does not prevent its diffusion through the thinner pore texture of the oxide coatings, possibly because of its poor hydration, related with lower charge density at the ion surfaces.     

Influence of Tetraalkylammonium Compounds on Photocatalytic and Physical Properties of TiO<Subscript>2</Subscript>

A wide range of experimental data are reported for the first time on the TiO₂ prepared by hydrolysis of highly concentrated Ti(OⁱPr)₄ in water solutions of quaternary ammonium compounds (QACs). These TiO₂ materials have been shown to be photocatalytically active under visible light irradiation (LED, 450 nm) using acetone as a model substrate oxidized in the gas phase. Five-fold increase in activity in comparison with the commercial photocatalyst KRONOClean 7000 is achieved. Colloidal solutions of hydrolyzed Ti(OⁱPr)₄ have been studied by SAXS method suggesting the way in which QACs solutions may influence the final composition of TiO₂. Phase composition, morphology, texture and surface properties of the modified TiO₂ have been studied using XRD, BET, SEM and low-temperature FTIR with CO probe. The surface elemental composition has been investigated by XPS method. Additional low-energy levels and high concentration of acid surface sites originated from N/C-doping, are likely to be the main reasons for exceptional photocatalytic performance of these samples.

Graphical Abstract

Open image in new window

     

Preparation of TiO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript> hollow spheres and their activity in methylene blue photodecomposition

PSA [poly-(styrene-methyl acrylic acid)] latex particle has been taken into account as template material in SiO₂ hollow spheres preparation. TiO₂-doped SiO₂ hollow spheres were obtained by using the appropriate amount of Ti(SO₄)₂ solution on SiO₂ hollow spheres. The photodecomposition of the MB (methylene blue) was evaluated on these TiO₂-doped SiO₂ hollow spheres under UV light irradiation. The catalyst samples were characterized by XRD, UV-DRS, SEM and BET. A TiO₂-doped SiO₂ hollow sphere has shown higher surface area in comparison with pure TiO₂ hollow spheres. The 40 wt% TiO₂-doped SiO₂ hollow sphere has been found as the most active catalyst compared with the others in the process of photodecomposition of MB (methylene blue). The BET surface area of this sample was found to be 377.6 m²g⁻¹. The photodegradation rate of MB using the TiO₂-doped SiO₂ catalyst was much higher than that of pure TiO₂ hollow spheres.     

Effect of oxidisable substrates on the photoelectrocatalytic properties of thermally grown and particulate TiO<Subscript>2</Subscript> layers

The photoelectrochemical properties of titanium dioxide layers, prepared by thermal oxidation of titanium at 500–750 °C, were compared with those of layers of particulate (Degussa) P25, especially for oxidation of oxalic acid. The thermally formed oxide layers had rutile structures with a particle size of about 100 nm. Values of incident photon-to-current conversion efficiencies increased with rutile layer thickness and reached a maximum at about 1 μm. Photocurrents for particulate TiO₂ layers were about one order lower than those for thermal layers, due to the poor contact among individual particles, resulting in high electric resistance of the whole layer. The presence of oxalic acid had no effect on the photocurrent of thermal TiO₂ layers, while in the case of porous particulate layers, the photocurrent increased strongly, due to oxalate adsorption and subsequent enhanced oxidation rate with photogenerated holes. For oxalic acid concentrations ≤10⁻³ M, the photocurrent decayed due to mass transfer limitations, resulting in oxalate depletion in the porous particulate layer.     

Photo-Generated Activities of Nanocrystalline TiO<Subscript>2</Subscript> Thin Films

Transparent nanocrystalline TiO₂ thin films with high photocatalytic activity and photo-induced wettability were successfully deposited on a glass slide. Crystal phase transformations and particle size of TiO₂ were investigated. Structural and morphological properties of the films were investigated. The photocatalytic activity of the TiO₂ films was evaluated. It is found that the photocatalytic activity of TiO₂ thin films is significantly decreased by increasing the annealing temperature, which results in a decrease in BET surface area and an increase in crystal size. In addition, increasing film thickness within a certain range significantly improves the photocatalytic activity without causing crack formation of the TiO₂ films. Photocatalytic oxidation and photo-induced wettability conversion on the films were investigated. It is found that photo-induced hydrophilic conversion is observed even on the samples annealed at high temperature. The best photo-generated activities are obtained by optimization of dip-coating cycles and annealing temperatures.     

Enhancement of the photoelectric performance of dye-sensitized solar cells using Ag-doped TiO<Subscript>2</Subscript> nanofibers in a TiO<Subscript>2</Subscript> film as electrode

For high solar conversion efficiency of dye-sensitized solar cells [DSSCs], TiO₂ nanofiber [TN] and Ag-doped TiO₂ nanofiber [ATN] have been extended to be included in TiO₂ films to increase the amount of dye loading for a higher short-circuit current. The ATN was used on affected DSSCs to increase the open circuit voltage. This process had enhanced the exit in dye molecules which were rapidly split into electrons, and the DSSCs with ATN stop the recombination of the electronic process. The conversion efficiency of TiO₂ photoelectrode-based DSSCs was 4.74%; it was increased to 6.13% after adding 5 wt.% ATN into TiO₂ films. The electron lifetime of DSSCs with ATN increased from 0.29 to 0.34 s and that electron recombination was reduced.     

A photocatalytic performance of TiO<Subscript>2</Subscript> photocatalyst prepared by the hydrothermal method

Anatase phase nanocrystalline TiO₂ powders were prepared by hydrothermal method with the TTIP (titanium tetra isopropoxide) at 200 oC in a stirred autoclave system. The effects of synthesis conditions on the physical properties of catalyst were investigated by using XRD, SEM, DLS, DSC and BET. The TiO₂ powders obtained from the optimum condition showed uniform spherical shape, crystalline structure, submicron size with a sharp size distribution and few agglomerates. The optimum synthesis conditions were obtained within the covered experimental ranges. The photocatalytic activity of TiO₂ powders prepared by the hydrothermal method was tested for photooxidation of methyl orange.     

Mg(OH)<Subscript>2</Subscript> Films Prepared by Ink-Jet Printing and Their Photocatalytic Activity in CO<Subscript>2</Subscript> Reduction and H<Subscript>2</Subscript>O Conversion

Mg(OH)₂ films on Al substrates were fabricated by ink-jet printing, and they were applied as photocatalysts in solar fuels production (H₂ and CH₃OH) from CO₂ and H₂O conversion. The films were fabricated by means of a deposition of a solution composed of magnesium complex nanoparticles over aluminum foils, which were submitted to a heat treatment to promote the crystallization of Mg(OH)₂. The films were characterized by razing incidence X-ray diffraction (GZXD), Fourier-transform infrared spectroscopy (FTIR), Scanning electronic microscopy, X-ray photoelectron spectroscopy (XPS), and N₂ physisorption by BET method. The Mg(OH)₂ was detected in all the samples synthesized with 1 to 40 layers. According to XPS and FTIR analysis, it was detected the presence of carbonates related to Mg₃O(CO₃)₂ and Al⁰ and Al³⁺ due to the substrate. The highest photocatalytic activity was reached using 30 layers of Mg(OH)₂ for H₂ and CH₃OH generation, which it was 268 and 15 µmol g^??1h^??1, respectively. These results were associated to the presence of adequate amounts of MgO and Al₂O₃ that promote an efficient transfer of the photogenerated electrons between them. Furthermore, the formation of porous structures with high surface area and relative high roughness promoted an increase in the mass transport between the gas and liquid phase, which increase the effectiveness of the photocatalysts.     

N<Subscript>2</Subscript>O fluxes and CO<Subscript>2</Subscript> exchange at different N doses under elevated CO<Subscript>2</Subscript> concentration in boreal agricultural mineral soil under <Emphasis Type="Italic">Phleum pratense</Emphasis>

The effects of elevated atmospheric CO₂ concentration on N₂O fluxes, instant CO₂ exchange and the biomass production of timothy (Phleum pratense) were studied in the laboratory. Three sets of 12 farmed sandy soil mesocosms sown with Phleum pratense were fertilised with a commercial fertiliser in order to add 5, 10 and 15 g N m⁻², and equally distributed in four thermo-controlled greenhouses. In two of the greenhouses, the CO₂ concentration was kept at atmospheric concentration (360 μmol mol⁻¹), and in the other two at double the ambient concentration (720 μmol mol⁻¹). Forage was harvested and the plants fertilised twice during the N₂O measurements. This was followed by an extra fertilisation and harvesting. After the third harvest, the growth of P. pratense was maintained at a height of 18 cm for measurements of instant CO₂ exchange, performed in two growth chambers. N₂O exchange was monitored using a closed chamber technique and a gas chromatograph. Instant CO₂ exchange was monitored using an infrared gas analyser. N₂O was emitted from the soil in the low, moderate and high N treatments at both CO₂ concentrations when the moisture content was low, the N₂O probably being mainly derived from nitrification. The highest flux (3303 μg N₂O m⁻² h⁻¹) occurred in the highest N treatment before thinning the stand of P. pratense under elevated CO₂ concentration. P. pratense was acclimated to the elevated CO₂ concentration: the NEE and P _G of the elevated growth of P. pratense decreased, in contrast to the fluxes of the normal ambient growth, when measured at the changed CO₂ concentration (ambient). The rate of respiration (R _TOT) in the agroecosystem did not increase due to the elevated CO₂ concentration, but instead the results indicated decreased R _TOT (on average 2049 and 1808 mg CO₂ m⁻² h⁻¹ at ambient and elevated CO₂ concentration, respectively) when there was an abundant N supply. This infers the possibility of enhanced C accumulation in agriculture mineral soil via P. pratense under an increased atmospheric CO₂ supply.     

Synthesis of TiO<Subscript>2</Subscript> nanoparticles from sprayed droplets of titanium tetrachloride by the gas-phase detonation method

Nanostructured polycrystalline titanium dioxides are produced by gas-phase detonation and pyrohydrolysis. Titanium tetrachloride (TiCl₄) is used as a precursor in the gas phase, and a premixed gas (O₂ and H₂) is used as a source of energy. The product is a mixture of TiO₂ crystals in the rutile phase (80%) and anatase phase (20%). __________ Translated from Fizika Goreniya i Vzryva, Vol. 44, No. 5, pp. 112–116, September–October, 2008.     

Photocatalytic inactivation and removal of algae with TiO<Subscript>2</Subscript>-coated materials

The capabilities of TiO₂-coated materials for the inactivation and removal of algae were investigated. As supports for TiO₂, non-woven fabric and Ni foam were chosen. To evaluate the ability of noble metal cocatalyst additions to facilitate the photocatalytic algal inhibition of TiO₂-coated materials, Pd nanoparticles were deposited on non-woven fabric-supported TiO₂ by photoelectrochemical deposition. The fabric-supported Pd/TiO₂ showed higher inhibition activity for algal growth compared to the fabric-supported TiO₂ without Pd. In addition, Ni foam-supported TiO₂ also showed high inhibition activity, both in laboratory-scale tests and open-air tests. Therefore, TiO₂-coated materials with suitable coating methods such as the use of cocatalysts or large surface area can substantially inhibit algal growth. The ability of the TiO₂-coated materials to inhibit algae correlated well with their activity for the photocatalytic decolorization of methylene blue, suggesting a nonspecific mechanism in the breakdown of cellular structures.     

Effect of Co,Ga, and Nd Additions on the Photocatalytic Properties of TiO<Subscript>2</Subscript> Nanopowders

In the present study, metal-ion-doped TiO₂ powders were prepared by a sol-gel process using titanium isopropoxide as a Ti precursor and cobalt, gallium, or neodymium as a dopant. For the prepared doped TiO₂ nanopowders, the photocatalytic behaviors in the decomposition of aqueous 1,4-dichlorobenzene (DCB) were investigated as a function of doping level and preparation conditions. We found that all of the metal ion doping improved the photocatalytic activity of TiO₂, though Nd doping was the most effective and Co doping was least effective. XRD analyses showed that doping with Ga and Nd ions suppresses the anatase-to-rutile phase transition for TiO₂, whereas doping with Co did not influence the phase transition. The UV-visible absorption spectra for these metal-ion-doped samples were red-shifted by ∼ 20–40 nm depending upon the doping level.Original English Text Copyright © 2005 by Fizika i Khimiya Stekla, Whang, J. Kim, E. Kim, Y. Kim, Lee.This article was submitted by the authors in English.     

Optical Properties of CeO<Subscript>2</Subscript> Doped SiO<Subscript>2</Subscript>-Na<Subscript>2</Subscript>O-CaO-P<Subscript>2</Subscript>O<Subscript>5</Subscript> Glasses

Cerium oxide is one of the most important rare earth elements that is introduced into glass compositions due to its great effects on the optical properties. CeO₂ was introduced in Hench’s patented SiO₂-Na₂O-CaO-P₂O₅ glasses with different concentrations in order to study its effect on the optical behavior of this glass including optical band gap, transmittance, reflectance and refractive index and to give a complete view for the optical properties on cerium oxide-doped silicate glasses.     

Photocatalytic Generation of H<Subscript>2</Subscript> Gas from Neat Ethanol over Pt/TiO<Subscript>2</Subscript> Nanotube Catalysts

TiO₂ nanotubes promoted with Pt metal were prepared and tested to be the photocatalytic dehydrogenation catalyst in neat ethanol for producing H₂ gas (C₂H₅OHC₃CHO +H₂). It was found that the ability to produce H₂, the liquid phase product distribution and the catlyst stability of these promoted nano catalysts all depended on the Pt loading and catalyst preparation procedure. These Pt/TiO₂ catalysts with TiO₂ nanotubes washed with diluted H₂SO₄ solution produced 1, 2-diethoxy ethane (acetal) as the major liquid phase product, while over those washed with diluted HCl solution or H₂O, acetaldehyde was the major liquid phase product.