共查询到20条相似文献,搜索用时 62 毫秒
1.
由于能源危机和环境保护等因素,政府法令和“能量、环境、经济、优越性”(即4个E)的要求,促进了胶粘剂工业的进一步发展。近年来,美国胶粘剂工业的发展主要表现在以下几个方面: 一、胶粘剂增长速度超过了国民经济的增长速度胶粘剂主要包括热塑性胶粘剂、热固性胶粘剂、橡胶胶粘剂和天然胶粘剂。现在,美国热塑性胶粘剂是价格最高的一种,用量不到胶粘剂总产量的20%,产值 相似文献
2.
最近开发的高功能胶粘剂1.使用方便、安全的水性胶粘剂水性胶粘剂现在主要使用于木工和纸加工,似乎是无新意的普通胶粘剂,但其使用方便,安全性高却是其他胶粘剂品种没有的高性能。乳液型胶粘剂是水性胶粘剂的主要品种,这种胶粘剂存在干燥速度慢,初期粘合强度低、对... 相似文献
3.
室温固化耐温胶粘剂研究进展 总被引:1,自引:0,他引:1
对国内外室温固化耐温胶粘剂的研究现状进行了综述。重点介绍了几种可室温固化的有机胶粘剂,包括环氧树脂胶粘剂、有机硅胶胶粘剂以及它们的改性产品,简述了无机胶粘剂在室温固化和高温使用方面的情况。提出了室温固化高温型胶粘剂今后的研究和发展方向。 相似文献
4.
5.
6.
7.
8.
要制造复合软包装材料,其中一个必不可少的原材料是胶粘剂。目前复合包装材料的主要用途又是食品、药品包装,未来食品/药品复合材料胶粘剂向无溶剂型方向发展,无溶剂胶粘剂基本上也是由双组份的聚氨酯胶粘剂构成的。 相似文献
9.
本文讨论了水溶性树脂的合成。通过与有机溶剂型胶粘剂、进口水基胶粘剂进行压制产品和剪切对比试验提出 ,合成的水溶性树脂可以用作盘式片的胶粘剂 ,其在工艺性能、产品剪切性能等方面比现广泛使用的有机溶剂型胶粘剂具有更多的优势 相似文献
10.
11.
研究了东方龙虱(雄性)抱握足上吸附脚掌的形态结构、吸附机制及其在2种不同表面的吸附特性。扫描电镜观察发现其吸附脚掌由4排吸附结构及其外围的吸附刚毛群构成,其吸附结构由约15个“鞋垫”状微吸盘平行并排构成一体。吸附机制为微吸盘的真空负压吸附和刚毛群的范德华力粘附。实验测定吸附脚掌在东方龙虱鞘翅表面和玻璃表面产生的最大法向吸附力为53.3 mN,最大切向吸附力为213.5 mN。在2种表面上(干、湿状态)其切向吸附力均远大于法向吸附力,大约是法向吸附力的6~8倍,同时吸附脚掌在湿表面的切向吸附力比干表面大得多,法向吸附力却相反。法向吸附力主要由刚毛群的范德华力产生,而切向吸附力由真空吸附和范德华力共同产生。 相似文献
12.
Surface pretreatment for adhesive bonding of aluminium with adhesive mediator SIP The present contribution describes the influence of different surface pretreatments including adhesive mediator SIP for adhesive bonding of aluminium alloy AlMg4,5Mn0,4. The investigations were performed using two cold hardening two‐components epoxy‐adhesives, one hot hardening one‐component epoxy‐adhesive and one cold hardening two‐components polyurethane‐adhesive. The adhesive bonds with epoxy‐adhesives show after three‐step pretreatment degreasing + corundblasting + SIP coating the highest adhesive strength values whereas adhesive bonds with polyurethane‐adhesive showed a decrease of bond strength as compared with the delivering surface condition. 相似文献
13.
瓦楞纸板用抗水淀粉胶配方及性能研究 总被引:2,自引:1,他引:1
简要分析了玉米淀粉胶的组成及对其质量的影响,重点对粘合剂的防水性进行了研究,叙述了瓦楞纸板用抗水粘合剂的配制及工艺过程,并与常规方法制备的粘合剂进行了性能比较,测定了抗水时间,得出了瓦楞纸板用抗水粘合剂的最佳配制比例。 相似文献
14.
制备了离子液体/杉木粉/酚醛树脂的复合胶粘剂,用DSC、FTIR和TGA分别对其固化温度、化学结构及热稳定性进行测试分析,研究了木粉和离子液体对复合胶粘剂性能的影响.结果表明,木粉能有效降低胶粘剂的游离醛含量,离子液体可以大幅度提高胶粘剂的胶合性能.与普通酚醛胶相比,当离子液体与木粉质量比为10:1时,复合胶粘剂游离醛从1.76%降低到0.24%,拉伸剪切强度从2.16 MPa提高到5.39 MPa,且固化后不龟裂,透明度较高.TGA结果表明复合胶的热分解温度提高,但残碳率降低.分析了被离子液体溶解的木粉对游离醛的捕捉作用及离子液体对胶合性能的贡献. 相似文献
15.
对采用SY-14胶粘剂生产胶部件的随炉件剥离强度进行了试验研究。结果表明,胶膜厚度,固化胶层度,尺寸和结构形式等对剥离强度都有影响,剥离强度指标应从结构设计用缺陷要求和胶粘剂性能统计处理的综合考查而确定。 相似文献
16.
为了能够对胶接对接接头进行抗拉强度预测,该文以有限元分析方法为基础,通过利用参考问题的无量纲应力强度因子、接头模型与参考问题模型之间应力值的比值以及接头抗拉强度的试验数值,得到了胶接对接接头的临界应力强度因子数值,从而提出了一个基于临界应力强度因子的胶接对接接头抗拉强度的简便预测新方法。该方法能够在保证精确度的基础上快速计算出胶接对接接头的应力强度因子,通过使用任意某一胶层厚度时的抗拉强度试验数值预测出其他胶层厚度时对接接头的抗拉强度数值。通过三种胶接对接接头的算例对比分析,证明了该方法的预测结果与实际结果非常接近,预测精度良好,便于工程应用。 相似文献
17.
Rajesh M. Pai Meenal S. Desai Asph D. Babtiwale R. Shrivastava 《Drug development and industrial pharmacy》1994,20(11):1905-1909
The kinetics of release of nitroglycerin from adhesive matrix type patches was studied. At a high drug to adhesive ratio the patch consisted of nitroglycerin in part dispersed as droplets in the adhesive and in part dissolved in the adhesive. This patch showed instant release of a major fraction of nitroglycerin in the patch and thereafter release kinetics similar to that which may be expected for a solution system. The rate of skin permeation of nitroglycerin was influenced by the drug to adhesive ratio; first increasing with increase in drug to adhesive ratio and then showing no significant change at a high drug to adhesive ratio at which the system was apparently an emulsion of nitroglycerin in the adhesive. 相似文献
18.
19.
Adhesives should be reinforced with reinforcing fibers for the bonding of adherends at cryogenic temperatures because all the adhesives become quite brittle at cryogenic temperatures. In this work, the film-type epoxy adhesive was reinforced with randomly oriented aramid fiber mats to decrease the CTE (Coefficient of Thermal Expansion) of the adhesive and to improve the fracture toughness of adhesive joints composed of stainless steel adherends at the cryogenic temperature of −150 °C. The cleavage tests of the DCB (Double Cantilever Beam) adhesive joints were performed to evaluate the fracture toughness and crack resistance of the adhesive joints. Also, the thermal and mechanical properties of the fiber reinforced adhesive layer were measured to investigate the relationship between the fracture toughness of adhesive joints and fiber volume fraction of aramid fibers. From the experiments, it was found that the crack propagated in the adhesive with the stable mode of significantly increased fracture toughness when the film-type epoxy adhesive was reinforced with aramid fiber mats. The optimum volume fraction of aramid fibers was suggested for the film-type epoxy adhesive in the adhesive joint at the cryogenic temperature of −150 °C. 相似文献