Pressureless sintering of binderless tungsten carbide

The aim of this study was to produce dense, single phase polycrystals. The research was carried out on the submicron tungsten carbide powder without additives, with either a carbon or tungsten additive and on the powder with both additives. The primary task of carbon was to reduce surface oxide impurities which passivate WC grains; tungsten in turn bounds free carbon in the WC. The authors manufactured fine-grained, dense (96–98% T.D.) and single-phase WC polycrystals, using the technique of pressureless sintering at the temperature not exceeding 2000 °C. A positive effect of carbon addition on tungsten carbide sinterability was observed, whereby a dense, fine-grained polycrystals can be obtained at 1900 °C. It was also observed that a significant excess of temperature of sintering process resulted in a strong abnormal grain growth of WC grains.     

CVD金刚石膜投资财务分析

文章从经济的角度,通过专业的财务分析,对CVD金刚石膜这一新型材料的投资价值进行研究。研究认为,CVD金刚石膜将成为金刚石材料未来发展的主流,其材料和制品具有广阔的市场前景。因此,投资CVD金刚石膜将获得丰厚的经济回报。     

Investigation the effect of FeNiCoCrMo HEA addition on properties of B4C ceramic prepared by spark plasma sintering

In this study, monolithic B₄C and B₄C-based ceramics incorporating FeNiCoCrMo dual-phase (FCC and BCC) high entropy alloys (HEAs) were produced by spark plasma sintering (SPS). The effect of additives on the densification behavior, mechanical properties, microstructures, and phase evaluation of the samples were investigated. X-ray analysis confirmed the existence of FCC structured HEA and depletion of BCC structured HEA, after high-temperature reaction between B₄C-HEAs. The addition of HEAs enhanced the densification behavior by liquid phase sintering. Furthermore, hardness and fracture toughness values of the samples increased with increasing HEAs content. Fracture toughness and hardness values for all composites were higher than the monolithic B₄C. A combination of the highest density (∼99.22 %) and the best mechanical properties (32.3 GPa hardness and 4.53 MPa m^1/2 fracture toughness) was achieved with 2.00 vol.% HEA addition.     

Adhesion of CVD diamond films on silicon substrates of different crystallographic orientations

In order to gain insight into the adhesion mechanisms of diamond films, we examine Si substrates with three different crystallographic orientations at the various stages of the deposition process. This allows one to distinguish the surface phenomena involved in diamond deposition from those due to gaseous plasma processes. We find that the initial ultrasonic scratching treatment produces partial graphitization of the diamond powder, and it controls the crystallite size through the carbon residues. On the other hand, an increased surface roughness due to H-atom etching correlates with increased adhesion. The deposited film adhesion is found to increase in the sequence Si(111)相似文献   

Static and dynamic mechanical properties of boron carbide processed by spark plasma sintering

Spark plasma sintering (SPS) has become a popular technique for the densification of covalent ceramics. The present investigation is focused on the static mechanical properties and dynamic compressive behavior of SPS consolidated boron carbide powder without any sintering additives. Fully dense boron carbide bodies were obtained by a short high temperature SPS treatment. The mechanical properties of the SPS-processed material, namely hardness (32 GPa), Young modulus (470 GPa), fracture toughness K_C (3.9–4.9 MPa m^0.5), flexural strength (430 MPa) and Hugoniot elastic limit (17–19 GPa) are close or even better than those of hot-pressed boron carbide.     

Densification mechanism,microstructure and mechanical properties of ZrC ceramics prepared by high-pressure spark plasma sintering

The traditional way of densifying high-melting-point ceramics at high temperatures with long soaking time leads to severe grain coarsening, which degrades the mechanical properties of ceramics. Here, highly dense (∼98%) zirconium carbide (ZrC) ceramics with limited grain growth were obtained by spark plasma sintering (SPS) at relatively low temperatures, 1900 ℃, with a high pressure up to 200 MPa in a reliable carbon-fiber-reinforced carbon composite (C_f/C) mold. Subgrains and high-density dislocations formed in the high-pressure sintered ceramics. The hardness and fracture toughness of the prepared highly dense ZrC ceramics reached 20.53 GPa and 2.70 MPa·m^1/2, respectively. The densification mechanism was mainly plastic deformation under high pressure. In addition, ZrC ceramics sintered at high pressure possessed a high dislocation density of 7.30 × 10¹² m⁻², which was suggested to contribute to the high hardness.     

Effect of solid solution formation on densification of spark plasma sintered ZrC ceramics with TiC as sintering aid

The densification of ZrC ceramics doped with different contents of TiC prepared by spark plasma sintering at the temperatures between 1750 and 1850°C has been investigated. The microstructure and mechanical properties of the ceramics have been characterised. It was shown that TiC additions effectively promoted the densification process by forming (Zr,Ti)C solid solution. The relative densities and mechanical properties of ZrC samples increased with the increasing of TiC content or the sintering temperature. Ceramic with the content of TiC up to 10 vol.-% sintering at 1850°C showed an excellent combination of properties including a relative density of 98.7%, hardness of 20.8?GPa and flexural strength of 605?MPa.     

Control of abnormal grain inclusions in the nanocrystalline diamond film deposited by hot filament CVD

Formation of abnormal grain inclusions in nanocrystalline diamond films deposited by hot filament CVD (HFCVD) was investigated. The phenomenon was attributed to two different origins: an intrinsic and an extrinsic one. The inclusions due to the intrinsic origin could be either avoided or weakened by controlling chamber pressure, CH₄/N₂ concentrations in H₂, and by positive substrate bias. The extrinsic origin for the abnormal grains was found to be the contamination from the alumina insulation tubes for the thermocouple placed near the substrate, which were degraded by the extended exposure to the high temperature and strongly reducing atmosphere.     

Microstructure,phase and electrical conductivity analyses of spark plasma sintered boron carbide machined with WEDM

Electrical conductivity is an essential property for machining of sintered boron carbide especially by wire electrical discharge machining (WEDM) process. Pure boron carbide was spark plasma sintered to full density at 2050 °C. Rietveld refinement on XRD analysis confirmed presence of B₁₃C₂ as the major phase in the powder as well as in the sintered samples.Electrical conductivity was found to be ~48 Ω⁻¹m⁻¹. The sintered specimens were successfully machined using WEDM technique. The microstructure of powder, machined and fractured surfaces of the sintered boron carbide were analyzed. At low power of WEDM with pulse current less than 140 A formation of molten, oxidized phases of boron carbide was observed as well as the development of surface cracks were minimum on the machined surface. Thus this work is aiming at achieving better product quality with sintered boron carbide specimens which are machined by WEDM.     

Densification and mechanical properties of boron carbide prepared via spark plasma sintering with cubic boron nitride as an additive

Hexagonal boron nitride (h-BN) can reinforce boron carbide (B₄C) ceramics, but homogeneous dispersion of h-BN is difficult to achieve using conventional methods. Herein, B₄C/h-BN composites were manufactured via the transformation of cubic (c-) BN during spark plasma sintering at 1800 °C. The effects of the c-BN content on the microstructure, densification, and mechanical properties of B₄C/h-BN composites were evaluated. In situ synthesized h-BN platelets were homogeneously dispersed in the B₄C matrix and the growth of B₄C grains was effectively suppressed. Moreover, the c-BN to h-BN phase transformation improved the sinterability of B₄C. The sample with 5 vol.% c-BN exhibited excellent integrated mechanical properties (hardness of 30.5 GPa, bending strength of 470 MPa, and fracture toughness of 3.84 MPa⋅ m^1/2). Higher c-BN contents did not significantly affect the bending strength and fracture toughness but clearly decreased the hardness. The main toughening mechanisms were crack deflection, crack bridging, and pulling out of h-BN.     

Microstructure and properties of Al2O3-TiC-Ti3SiC2 composites fabricated by spark plasma sintering

Abstract

Abstract

Highly densified Al₂O₃-TiC-Ti₃SiC₂ composites were fabricated by spark plasma sintering technique and subsequently characterised. From fracture surface observation, it is found that Al₂O₃ is 0·2-0·4?μm, TiC is 1-1·5?μm and Ti₃SiC₂ is 1·5-5?μm in grain size. With the increase in Ti₃SiC₂ volume contents, Vickers hardness of the composites decreases because of the low hardness of monolithic Ti₃SiC₂. The fracture toughness rises remarkably when the contents of Ti₃SiC₂ increase, which is attributed to the pullout and microplastic deformation of Ti₃SiC₂ grains. At the same time, the flexural strength of the composites shows a considerable improvement as well. The electrical conductivity rises significantly as the Ti₃SiC₂ contents increase because of the formation of Ti₃SiC₂ network and the increase in conductive phase contents.     

Mechanical properties of nano-grain SiO2 glass prepared by spark plasma sintering

Silicon carbide (SiC) layers were deposited on silica (SiO₂) glass powder by rotary chemical vapor deposition (RCVD) to form SiO₂ glass (core)/SiC (shell) powder; this powder was consolidated by spark plasma sintering (SPS). SiO₂ glass powder with a particle size of 250 nm was coated with 5–10-nm-thick SiC layers. The resultant SiO₂ glass (core)/SiC (shell) powder was consolidated to form a nano-grain SiO₂ glass composite at a relative density above 90% by SPS in the sintering temperature range of 1573–1823 K. The Vickers hardness and fracture toughness of the SiO₂ glass composite at 1723 K were found to be 14.2 GPa and 5.4 MPa m^1/2, respectively.     

In-situ synthesis and densification of boron carbide and boron carbide-graphene nanoplatelet composite by reactive spark plasma sintering

Simultaneous synthesis and densification of boron carbide and boron carbide- graphene nano platelets (GNP) were carried out by reactive spark plasma sintering of amorphous boron and graphene nano platelets at temperature ranging from 1200 to 1600?°C, pressure of 50?MPa and heating rate of 50?°C/min and 100?°C/min. X-ray diffraction and Raman spectroscopy confirmed the formation of required phases. Electron microscopic images revealed the formation of sub-micron and nano sized grains of plate like morphology. Sintered product with high relative density of 96%TD was achieved at a temperature of 1600?°C and heating rate of 50?°C/min for B₄C stoichiometric composition and also exhibited maximum hardness of 21.10?GPa.     

砷化镓上生长金刚石薄膜的研究

以CH4和H2为气源,用微波辅助等离子体装置,在10.0 mm×7.0 mm的砷化镓基底上沉积了CVD金刚石薄膜,用扫描电子显微镜观察沉积效果,拉曼光谱表征沉积质量,分析薄膜附着力与砷化镓材料性能的关系。结果表明,当基体温度为600℃,气压为5 kPa,甲烷浓度为2.0%时,在砷化镓片表面上沉积出了CVD金刚石薄膜,晶粒尺寸均匀,晶形完整、规则,晶界非常清晰。     

Spark plasma sintering of WC-based cermets/titanium and vanadium added composites: A comparative study on the microstructure and mechanical properties

In an attempt to develop the composition and properties of W₂C-(W,Ti)C-TiC and WC-WC_1-x-VC-V super hardmetals, spark plasma sintering (SPS) method was implemented. WC powders were mixed separately with 10?wt% Ti and 10?wt% V in a high energy mixer mill and sintering processes were performed at temperatures of 2150 and 2000?°C, respectively. XRD investigations revealed the formations of TiC and (Ti,W)C as the reaction products in WC-10?wt% Ti composite. Moreover, the interfacial reaction between WC and V led to the formation of WC1-x and VC compounds. A higher bending strength (613?±?25?MPa) and fracture toughness (4.1?±?0.58?MPa?m^1/2) were obtained for WC-10?wt% V samples compared to WC-10?wt% Ti, While the WC-10?wt% Ti composite showed a higher value of hardness (3128?±?42 Vickers) in comparison to WC-10?wt% V (2632?±?39 Vickers), which can act as a super hard cermet.     

Wear and friction properties of spark plasma sintered SiC/Cu nanocomposites

In this study, in order to determine the effect of SiC nanoparticles on tribological properties of nanostructured copper, the dry sliding wear and friction behaviors of nanostructured copper and copper reinforced with silicon carbide nanoparticles, produced by high energy ball milling and spark plasma sintering, were investigated by using an oscillating friction and wear tester under different normal loads. To determine the dominant wear mechanism, the worn surfaces and obtained debris after wear tests were analyzed by scanning electron microscope (SEM). The results showed that the addition of 4 vol% silicon carbide to copper matrix reduced the wear track depth and the coefficient of friction. Investigation of the worn surfaces revealed that SiC nanoparticles on the top of worn surface decreases the plastic deformation in subsurface region and alleviate severe wear. Lower plastic deformation during dry sliding wear test was attributed to high hardness of the nanocomposite that has been resulted from grain growth inhibiting and reinforcing effects of the nanoparticles. Plastic deformation and delamination were determined as major wear mechanisms in both materials.     

Drucker-Prager-Cap modelling of boron carbide powder for coupled electrical-thermal-mechanical finite element simulation of spark plasma sintering

The coupled electrical-thermal-mechanical finite element method in the continuum scale has been widely used to investigate the spark plasma sintering process. An accurate constitutive model of powder material is pivotal for precise continuum finite element simulation. In this study, the Drucker-Prager-Cap model, which is highly accurate in describing the densification behaviour of powder material, was adopted to numerically analyse the spark plasma sintering process of boron carbide powder. First, the parameters of the model were defined to be dependent on temperature and density for higher accuracy; they were determined by minimising the discrepancy between the simulated and experimental results. Based on a spark plasma sintering experiment with a cylindrical sample, the parameters of the Drucker-Prager-Cap model were identified at 1500 °C, 1600 °C, 1700 °C, 1800 °C, and 1900 °C. A coupled electrical-thermal-mechanical finite element simulation with the model was performed for spark plasma sintering of boron carbide powder at 1750 °C and 1850 °C. The temperature, stress, and relative density were investigated numerically. By comparing the model results with the temperature and relative density measured in the experiment, the continuum finite element method with the Drucker-Prager-Cap model was validated.     

Reduced-graphene-oxide-reinforced boron carbide ceramics fabricated by spark plasma sintering from powder mixtures obtained by heterogeneous co-precipitation

Reduced graphene oxide (rGO) sheets were uniformly dispersed in boron carbide ceramics by a heterogeneous co-precipitation method. This approach was used to improve the fracture toughness of boron carbide ceramics and to address the problem of agglomeration of graphene in the boron carbide matrix. Cetyltrimethyl ammonium bromide was used as a heterogeneous co-precipitation reaction initiator to prepare a homogeneously dispersed graphene oxide/boron carbide (GO/B₄C) mixture. Reduced graphene oxide/boron carbide (rGO/B₄C) powder mixtures with good dispersion were obtained by high temperature heat treatment. Dense rGO/B₄C composite ceramics were fabricated by spark plasma sintering at 1800 °C and 50 MPa. The fracture toughness and flexural strength of the rGO/B₄C with an rGO content of 2 vol% composite increased by 42% (from 3.43 to 4.88 MPa·m^1/2) and 28% (from 372 to 476 MPa) compared with those of pure B₄C, respectively. The markedly improved fracture toughness and flexural strength of the boron carbide ceramics were attributed to the effect of crack bridging and crack deflection by graphene sheets, graphene interface sliding, and pulling out of graphene.     

Influence of chemical composition on mechanical properties of spark plasma sintered boron carbide monoliths

Fully dense boron carbide monoliths exhibiting fine microstructure (i.e., submicrometric grain size) are sintered by Spark Plasma Sintering. Two different commercial powder batches, exhibiting different stoichiometries (i.e., B/C ratio and oxygen content) and various amounts of secondary phases (i.e., boric acid and free carbon), are used. Their chemical composition is well‐defined by coupling different methods (Transmission Electron Microscopy associated with XRD analyses, and Instrumental Gas Analysis), and are correlated with their mechanical properties, characterized from meso‐ to macro‐scopic scales by nano‐indentation and ultrasonic pulse echography. The presence of secondary phases (graphite and boric acid) is evidenced in various proportions in each powder batch. If the boric acid disappears during sintering, the graphite remains. However, for the considered amounts of graphite (lower than 1 wt%), the low variations in graphite content have no significant effect on hardness and elasticity values. At the opposite, the presence of oxygen in boron carbide lattice, leading to a boron oxycarbide phase, induces a decrease in both hardness and elasticity properties.