ESD protection design for mixed-voltage I/O buffer with substrate-triggered circuit

A substrate-triggered technique is proposed to improve the electrostatic discharge (ESD) robustness of a stacked-nMOS device in the mixed-voltage I/O circuit. The substrate-triggered technique can further lower the trigger voltage of a stacked-nMOS device to ensure effective ESD protection for mixed-voltage I/O circuits. The proposed ESD protection circuit with substrate-triggered design for a 2.5-V/3.3-V-tolerant mixed-voltage I/O circuit has been fabricated and verified in a 0.25-/spl mu/m salicided CMOS process. The substrate-triggered circuit for a mixed-voltage I/O buffer to meet the desired circuit application in different CMOS processes can be easily adjusted by using HSPICE simulation. Experimental results have confirmed that the human- body-model (HBM) ESD robustness of a mixed-voltage I/O circuit can be increased /spl sim/60% by this substrate-triggered design.     

Electrostatic discharge protection design for mixed-voltage CMOS I/O buffers

A new electrostatic discharge (ESD) protection circuit, using the stacked-nMOS triggered silicon controlled rectifier (SNTSCR) as the ESD clamp device, is designed to protect the mixed-voltage I/O buffers of CMOS ICs. The new proposed ESD protection circuit, which combines the stacked-nMOS structure with the gate-coupling circuit technique into the SCR device, is fully compatible to general CMOS processes without causing the gate-oxide reliability problem. Without using the thick gate oxide, the experimental results in a 0.35 /spl mu/m CMOS process have proven that the human-body-model ESD level of the mixed-voltage I/O buffer can be successfully increased from the original /spl sim/2 kV to >8 kV by using this proposed ESD protection circuit.     

Substrate-triggered ESD protection circuit without extra process modification

A substrate-triggered technique is proposed to improve electrostatic discharge (ESD) protection efficiency of ESD protection circuits without extra salicide blocking and ESD-implantation process modifications in a salicided shallow-trench-isolation CMOS process. By using the layout technique, the whole ESD protection circuit can be merged into a compact device structure to enhance the substrate-triggered efficiency. This substrate-triggered design can increase ESD robustness and reduce the trigger voltage of the ESD protection device. This substrate-triggered ESD protection circuit with a field oxide device of channel width of 150 /spl mu/m can sustain a human-body-model ESD level of 3250 V without any extra process modification. Comparing to the traditional ESD protection design of gate-grounded nMOS (ggnMOS) with silicide-blocking process modification in a 0.25-/spl mu/m salicided CMOS process, the proposed substrate-triggered design without extra process modification can improve ESD robustness per unit silicon area from the original 1.2 V//spl mu/m/sup 2/ of ggnMOS to 1.73 V//spl mu/m/sup 2/.     

Design on Power-Rail ESD Clamp Circuit for 3.3-V I/O Interface by Using Only 1-V/2.5-V Low-Voltage Devices in a 130-nm CMOS Process

A new power-rail electrostatic discharge (ESD) clamp circuit for application in 3.3-V mixed-voltage input–output (I/O) interface is proposed and verified in a 130-nm 1-V/2.5-V CMOS process. The devices in this power-rail ESD clamp circuit are all 1-V or 2.5-V low-voltage nMOS/pMOS devices, which are specially designed without suffering the gate-oxide reliability issue under 3.3-V I/O interface applications. A special ESD detection circuit realized with the low-voltage devices is designed and added in the power-rail ESD clamp circuit to improve ESD robustness of ESD clamp devices by substrate-triggered technique. The experimental results verified in a 130-nm CMOS process have proven the excellent effectiveness of this new proposed power-rail ESD clamp circuit.     

ESD protection design for CMOS RF integrated circuits using polysilicon diodes

ESD protection design for CMOS RF integrated circuits is proposed in this paper by using the stacked polysilicon diodes as the input ESD protection devices to reduce the total input capacitance and to avoid the noise coupling from the common substrate. The ESD level of the stacked polysilicon diodes on the I/O pad is restored by using the turn-on efficient power-rail ESD clamp circuit, which is constructed by substrate-triggered technique. This polysilicon diode is fully process compatible to general sub-quarter-micron CMOS processes.     

Overview on ESD protection design for mixed-voltage I/O interfaces with high-voltage-tolerant power-rail ESD clamp circuits in low-voltage thin-oxide CMOS technology

Electrostatic discharge (ESD) protection design for mixed-voltage I/O interfaces has been one of the key challenges of system-on-a-chip (SOC) implementation in nanoscale CMOS processes. The on-chip ESD protection circuit for mixed-voltage I/O interfaces should meet the gate-oxide reliability constraints and prevent the undesired leakage current paths. This paper presents an overview on the design concept and circuit implementations of ESD protection designs for mixed-voltage I/O interfaces with only low-voltage thin-oxide CMOS transistors. Especially, the ESD protection designs for mixed-voltage I/O interfaces with ESD bus and high-voltage-tolerant power-rail ESD clamp circuits are presented and discussed.     

基于STNMOS的混合电压I／O接口ESD保护

混合电压I／O接口的静电放电（electrostaticdischarge,ESD）保护设计是小线宽工艺中片上系统（SoC）设计的主要挑战之一。混合电压I／O接口的片上ESD保护既要避免栅氧可靠性问题,又要防止不期望的泄漏电流路径产生。这篇论文讨论了基于堆叠NMOS（Stacked—NMOS,STNMOS）的混合电压I／O接口的ESD保护设计构思和电路实现,通过不同ESD保护设计方案的比较,提出了一个最有效的保护方案。     

Latchup-free ESD protection design with complementary substrate-triggered SCR devices

The turn-on mechanism of silicon-controlled rectifier (SCR) devices is essentially a current triggering event. While a current is applied to the base or substrate of an SCR device, it can be quickly triggered on into its latching state. In this paper, latchup-free electrostatic discharge (ESD) protection circuits, which are combined with the substrate-triggered technique and an SCR device, are proposed. A complementary circuit style with the substrate-triggered SCR device is designed to discharge both the pad-to-V/sub SS/ and pad-to-V/sub DD/ ESD stresses. The novel complementary substrate-triggered SCR devices have the advantages of controllable switching voltage, adjustable holding voltage, faster turn-on speed, and compatible to general CMOS process without extra process modification such as the silicide-blocking mask and ESD implantation. The total holding voltage of the substrate-triggered SCR device can be linearly increased by adding the stacked diode string to avoid the transient-induced latchup issue in the ESD protection circuits. The on-chip ESD protection circuits designed with the proposed complementary substrate-triggered SCR devices and stacked diode string for the input/output pad and power pad have been successfully verified in a 0.25-/spl mu/m salicided CMOS process with the human body model (machine model) ESD level of /spl sim/7.25 kV (500 V) in a small layout area.     

Overview on electrostatic discharge protection designs for mixed-voltage I/O interfaces: design concept and circuit implementations

Electrostatic discharge (ESD) protection design for mixed-voltage I/O interfaces has been one of the key challenges of system-on-a-chip (SOC) implementation in nano-scale CMOS processes. The on-chip ESD protection circuit for mixed-voltage I/O interfaces should meet the gate-oxide reliability constraints and prevent the undesired leakage current paths. This paper presents an overview on the design concept and circuit implementations of the ESD protection designs for mixed-voltage I/O interfaces without using the additional thick gate-oxide process. The ESD design constraints in mixed-voltage I/O interfaces, the classification and analysis of ESD protection designs for mixed-voltage I/O interfaces, and the designs of high-voltage-tolerant power-rail ESD clamp circuit are presented and discussed.     

ESD protection design for I/O cells with embedded SCR structure as power-rail ESD clamp device in nanoscale CMOS technology

This paper presents a new electrostatic discharge (ESD) protection design for input/output (I/O) cells with embedded silicon-controlled rectifier (SCR) structure as power-rail ESD clamp device in a 130-nm CMOS process. Two new embedded SCR structures without latchup danger are proposed to be placed between the input (or output) pMOS and nMOS devices of the I/O cells. Furthermore, the turn-on efficiency of embedded SCR can be significantly increased by substrate-triggered technique. Experimental results have verified that the human-body-model (HBM) ESD level of this new proposed I/O cells can be greater than 5 kV in a 130-nm fully salicided CMOS process. By including the efficient power-rail ESD clamp device into each I/O cell, whole-chip ESD protection scheme can be successfully achieved within a small silicon area of the I/O cell.     

Substrate-triggered SCR device for on-chip ESD protection in fully silicided sub-0.25-/spl mu/m CMOS process

The turn-on mechanism of a silicon-controlled rectifier (SCR) device is essentially a current triggering event. While a current is applied to the base or substrate of the SCR device, it can be quickly triggered into its latching state. In this paper, a novel design concept to turn on the SCR device by applying the substrate-triggered technique is first proposed for effective on-chip electrostatic discharge (ESD) protection. This novel substrate-triggered SCR device has the advantages of controllable switching voltage and adjustable holding voltage and is compatible with general CMOS processes without extra process modification such as the silicide-blocking mask and ESD implantation. Moreover, the substrate-triggered SCR devices can be stacked in ESD protection circuits to avoid the transient-induced latch-up issue. The turn-on time of the proposed substrate-triggered SCR devices can be reduced from 27.4 to 7.8 ns by the substrate-triggering technique. The substrate-triggered SCR device with a small active area of only 20 /spl mu/m /spl times/ 20 /spl mu/m can sustain the HBM ESD stress of 6.5 kV in a fully silicided 0.25-/spl mu/m CMOS process.     

ESD Protection Design With On-Chip ESD Bus and High-Voltage-Tolerant ESD Clamp Circuit for Mixed-Voltage I/O Buffers

Considering gate-oxide reliability, a new electrostatic discharge (ESD) protection scheme with an on-chip ESD bus (ESD_BUS) and a high-voltage-tolerant ESD clamp circuit for 1.2/2.5 V mixed-voltage I/O interfaces is proposed. The devices used in the high-voltage-tolerant ESD clamp circuit are all 1.2 V low-voltage N- and P-type MOS devices that can be safely operated under the 2.5-V bias conditions without suffering from the gate-oxide reliability issue. The four-mode (positive-to-V_SS, negative-to-V_SS, positive-to-V_DD, and negative-to-V_DD) ESD stresses on the mixed-voltage I/O pad and pin-to-pin ESD stresses can be effectively discharged by the proposed ESD protection scheme. The experimental results verified in a 0.13-mum CMOS process have confirmed that the proposed new ESD protection scheme has high human-body model (HBM) and machine-model (MM) ESD robustness with a fast turn-on speed. The proposed new ESD protection scheme, which is designed with only low- voltage devices, is an excellent and cost-efficient solution to protect mixed-voltage I/O interfaces.     

Stacked-NMOS triggered silicon-controlled rectifier for ESDprotection in high/low-voltage-tolerant I/O interface

A stacked-NMOS triggered silicon-controlled rectifier (SNTSCR) is proposed as the electrostatic discharge (ESD) clamp device to protect the mixed-voltage I/O buffers of CMOS ICs. This SNTSCR device is fully compatible to general CMOS processes without using a thick gate oxide to overcome the gate-oxide reliability issue. ESD robustness of the proposed SNTSCR device with different layout parameters has been investigated in a 0.35 μm CMOS process. The HBM ESD level of the mixed-voltage I/O buffer with the stacked-NMOS channel width of 120 μm can be obviously improved from the original ~2 kV to be greater than 8 kV by this SNTSCR device with device dimensions of only 60 μm/0.35 μm     

SCR device fabricated with dummy-gate structure to improve turn-on speed for effective ESD protection in CMOS technology

Turn-on speed is the main concern for an on-chip electrostatic discharge (ESD) protection device, especially in the nanoscale CMOS processes with ultrathin gate oxide. A novel dummy-gate-blocking silicon-controlled rectifier (SCR) device employing a substrate-triggered technique is proposed to improve the turn-on speed of an SCR device for using in an on-chip ESD protection circuit to effectively protect the much thinner gate oxide. The fabrication of the proposed SCR device with dummy-gate structure is fully process-compatible with general CMOS process, without using an extra mask layer or adding process steps. From the experimental results in a 0.25-/spl mu/m CMOS process with a gate-oxide thickness of /spl sim/50 /spl Aring/, the switching voltage, turn-on speed, turn-on resistance, and charged-device-model ESD levels of the SCR device with dummy-gate structure have been greatly improved, as compared to the normal SCR with shallow trench isolation structure.     

ESD implantation for subquarter-micron CMOS technology to enhance ESD robustness

A new electrostatic discharge (ESD) implantation method is proposed to significantly improve ESD robustness of CMOS integrated circuits in subquarter-micron CMOS processes, especially the machine-model (MM) ESD robustness. By using this method, the ESD current is discharged far away from the surface channel of nMOS, therefore the nMOS (both single nMOS and stacked nMOS) can sustain a much higher ESD level. The MM ESD robustness of the gate-grounded nMOS with a device dimension width/length (W/L) of 300 /spl mu/m/0.5 /spl mu/m has been successfully improved from the original 450 V to become 675 V in a 0.25-/spl mu/m CMOS process. The MM ESD robustness of the stacked nMOS in the mixed-voltage I/O circuits with a device dimension W/L of 300 /spl mu/m/0.5 /spl mu/m for each nMOS has been successfully improved from the original 350 V to become 500 V in the same CMOS process. Moreover, this new ESD implantation method with the n-type impurity can be fully merged into the general subquarter-micron CMOS processes.     

A new on-chip ESD protection circuit with dual parasitic SCRstructures for CMOS VLSI

A new CMOS on-chip electrostatic discharge (ESD) protection circuit which consists of dual parasitic SCR structures is proposed and investigated. Experimental results show that with a small layout area of 8800 μ², the protection circuit can successfully perform negative and positive ESD protection with failure thresholds greater than ±1 and ±10 kV in machine-mode (MM) and human-body-mode (HBM) testing, respectively. The low ESD trigger voltages in both SCRs can be readily achieved through proper circuit design and without involving device or junction breakdown. The input capacitance of the proposed protection circuit is very low and no diffusion resistor between I/O pad and internal circuits is required, so it is suitable for high-speed applications. Moreover, this ESD protection circuit is fully process compatible with CMOS technologies     

Electrostatic discharge protection scheme without leakage current path for CMOS IC operating in power-down-mode condition on a system board

A new design on the electrostatic discharge (ESD) protection scheme for CMOS IC operating in power-down-mode condition is proposed. By adding a VDD_ESD bus line and diodes, the new proposed ESD protection scheme can block the leakage current from I/O pin to VDD power line to avoid malfunction during power-down-mode operating condition. During normal circuit operating condition, the new proposed ESD protection schemes have no leakage path to interfere with the normal circuit functions. The whole-chip ESD protection design can be achieved by insertion of ESD clamp circuits between VSS power line and both VDD power line and VDD ESD bus line. Experimental results have verified that the human-body-model (HBM) ESD level of this new scheme can be greater than 7.5 kV in a 0.35-μm silicided CMOS process. Furthermore, output-swing improvement circuit is proposed to achieve the full swing of output voltage level during normal circuit operating condition.     

Overview and Design of Mixed-Voltage I/O Buffers With Low-Voltage Thin-Oxide CMOS Transistors

Overview on the prior designs of the mixed-voltage I/O buffers is provided in this work. A new 2.5/5-V mixed-voltage I/O buffer realized with only thin gate-oxide devices is proposed. The new proposed mixed-voltage I/O buffer with simpler dynamic n-well bias circuit and gate-tracking circuit can prevent the undesired leakage current paths and the gate-oxide reliability problem, which occur in the conventional CMOS I/O buffer. The new mixed-voltage I/O buffer has been fabricated and verified in a 0.25-$mu$m CMOS process to serve 2.5/5-V I/O interface. Besides, another 2.5/5-V mixed-voltage I/O buffer without the subthreshold leakage problem for high-speed applications is also presented in this work. The speed, power consumption, area, and noise among these mixed-voltage I/O buffers are also compared and discussed. The new proposed mixed-voltage I/O buffers can be easily scaled toward 0.18-$mu$m (or below) CMOS processes to serve other mixed-voltage I/O interfaces, such as 1.8/3.3-V interface.     

Design of 2.4-GHz T/R switch with embedded ESD protection devices in CMOS process

As CMOS processes advanced, the integration of radio-frequency (RF) integrated circuits was increasing. In order to protect the fully-integrated RF transceiver from electrostatic discharge (ESD) damage, the transmit/receive (T/R) switch of transceiver frond-end should be carefully designed to bypass the ESD current. This work presented a technique of embedded ESD protection device to enhance the ESD capability of T/R switch. The embedded ESD protection devices of diodes and silicon-controlled rectifier (SCR) are generated between the transistors in T/R switch without using additional ESD protection device. The design procedure of RF circuits without ESD protection device can be simplified. The test circuits of 2.4-GHz transceiver frond-end with T/R switch, PA, and LNA have been integrated and implemented in nanoscale CMOS process to test their performances during RF operations and ESD stresses. The test results confirm that the embedded ESD protection devices can provide sufficient ESD protection capability and it is free from degrading circuit performances.     

ESD protection design on analog pin with very low input capacitancefor high-frequency or current-mode applications

An electrostatic discharge (ESD) protection design is proposed to solve the ESD protection challenge to the analog pins: for high-frequency or current-mode applications, By including an efficient power-rails clamp circuit in the analog input/output (I/O) pin, the device dimension (W/L) of an ESD clamp device connected to the I/O pad in the analog ESD protection circuit can be reduced to only 50/0.5 (μm/μm) in a 0.35-μm silicided CMOS process, but it can sustain the human body model (HBM) and machine model (MM) ESD level of up to 6 kV (400 V). With such a smaller device dimension, the input capacitance of this analog ESD protection circuit can be significantly reduced to only ~1.0 pF (including the bond-pad capacitance) for high-frequency applications