无盖板渗透型太阳能空气集热器热性能的实验研究

无盖板渗透型太阳能空气集热器是一种易于实现建筑一体化的高效新风预热及干燥装置。为了掌握无盖板渗透型集热器在实际工况下的热性能,建造了集热面积为2.2 m2的太阳能空气加热系统实验台,并在2009年2月至2009年4月对其热性能进行了户外瞬态实验研究。实验结果表明出口空气温度随辐射强度的增加而升高,太阳辐射强度是影响集热器出口空气温度的最重要因素,而室外空气温度的影响极小。空气温升随风量的增加而减小,集热器热效率随风量的增加而增大。在三个测试日中集热器的平均热效率分别为58%、63%和72%,高于普通平板太阳能空气集热器。     

无盖板渗透型集热器热性能的对比试验

利用太阳能空气加热系统实验台,对黑、深绿和深蓝3种颜色无盖板渗透型集热器的热性能进行了户外瞬态对比试验。试验结果表明:太阳辐射照度和风量是影响系统热性能的重要因素。在高档和低档两种风量下,黑色集热器的瞬时平均热效率分别为76.04%和67.50%,高于普通平板太阳能空气集热器;集热器表面颜色对其热性能有一定影响,在高档和低档两种风量下,深绿色和深蓝色集热器的瞬时平均热效率比黑色集热器低15%～22%,空气温升低3～4℃,但仍然优于普通平板空气集热器。从保持建筑立面美观考虑,无盖板渗透型集热器的集热板可以采用颜色较深的彩色,不会对系统热性能造成较大影响。     

Use of unglazed transpired solar collectors for desiccant cooling

The use of unglazed transpired solar collectors for desiccant regeneration in a solid desiccant cooling cycle was investigated because these collectors are less expensive than conventional glazed flat-plate collectors. Using computer models, we studied the performance of a desiccant cooling ventilation cycle integrated with either unglazed transpired collectors or conventional glazed flat-plate collectors. We found that the thermal coefficient of performance of the cooling system with unglazed collectors was lower than that of the cooling system with glazed collectors because the former system did not use the heat of adsorption released during the dehumidification process. Although the area required for the unglazed collector array was 70% more than that required for the glazed collector array in a 10.56 kW (3 ton) solar cooling system, the cost of the unglazed array was 45% less than the cost of the glazed array. The simple payback period of the unglazed collector was half of the payback period of the glazed collector when replacing an equivalent gas-fired air heater. Although the use of unglazed transpired collectors seems to make economic sense relative to use of glazed conventional collectors, some practical considerations may limit their use for desiccant regeneration.     

渗透型太阳能空气集热器集热效率研究

将CFD模拟引入太阳能空气集热器设计研究领域,对渗透型太阳能空气集热器(UTC)的工作特性进行了模拟分析,并与传统空气集热器进行了比较.在数值模拟的基础上,制作了几种实验模型并进行了实验研究,对其送风温度和热效率进行了测试.通过模拟和模型实验,说明了UFC在新风预热领域中无可比拟的优势,显示了CFD工具在空气集热器研究领域中的优势.     

Performance improvement of PV/T solar collectors with natural air flow operation

The electrical efficiency of a photovoltaic system drops as its operating temperature rises and PV cooling is necessary. The photovoltaic/thermal (PV/T) system is a relatively recent type of solar collector where a circulating fluid of lower temperature than PV module extracts heat from it, cooling the module to improve its output power while the solar pre-heated fluid provides sensible heat. In the present work, air cooling of a commercial PV module configured as PV/T air solar collector by natural flow is presented, where two low cost modification techniques to enhance heat transfer to air stream in the air channel are studied. The considered methods consist of thin metal sheet suspended at the middle or fins attached to the back wall of the air-channel to improve heat extraction from the module. A numerical model was developed and validated against the experimental data obtained from outdoor test campaigns for both glazed and unglazed PV/T prototype models studied. The validation results show good agreement between predicted values and measured data and thus could be used to study analytically the performance of these PV/T air collectors with respect to several design and operating parameters. The modified systems present better performance than the usual type and will contribute to better performance of integrated PV systems for natural ventilation applications in buildings, both space cooling and heating.     

Parametric study of various configurations of hybrid PV/thermal air collector: Experimental validation of theoretical model

In this paper, an attempt has been made to evaluate the overall performance of hybrid PV/thermal (PV/T) air collector. The different configurations of hybrid air collectors which are considered as unglazed and glazed PV/T air heaters, with and without tedlar. Analytical expressions for the temperatures of solar cells, back surface of the module, outlet air and the rate of extraction of useful thermal energy from hybrid PV/T air collectors have been derived. Further an analytical expression similar to Hottel–Whiller–Bliss (HWB) equation for flat plate collector has also been derived in terms of design and climatic parameters. Numerical computations have been carried out for composite climate of New Delhi and the results for different configurations have been compared. The thermal model for unglazed PV/T air heating system has also been validated experimentally for summer climatic conditions. It is observed that glazed hybrid PV/T without tedlar gives the best performance.     

A prototype photovoltaic/thermal system integrated with transpired collector

Building-integrated photovoltaic/thermal (BIPV/T) systems may be utilized to produce useful heat while simultaneously generating electricity from the same building envelope surface. A well known highly efficient collector is the open-loop unglazed transpired collector (UTC) which consists of dark porous cladding through which outdoor air is drawn and heated by absorbed solar radiation. Commercially available photovoltaic systems typically produce electricity with efficiencies up to about 18%. Thus, it is beneficial to obtain much of the normally wasted heat from the systems, possibly by combining UTC with photovoltaics. Combination of BIPV/T and UTC systems for building facades is considered in this paper - specifically, the design of a prototype façade-integrated photovoltaic/thermal system with transpired collector (BIPV/T). A full scale prototype is constructed with 70% of UTC area covered with PV modules specially designed to enhance heat recovery and compared to a UTC of the same area under outdoor sunny conditions with low wind. The orientation of the corrugations in the UTC is horizontal and the black-framed modules are attached so as to facilitate flow into the UTC plenum. While the overall combined thermal efficiency of the UTC is higher than that of the BIPV/T system, the value of the generated energy - assuming that electricity is at least four times more valuable than heat - is between 7% and 17% higher. Also, the electricity is always useful while the heat is usually utilized only in the heating season. The BIPV/T concept is applied to a full scale office building demonstration project in Montreal, Canada. The ratio of photovoltaic area coverage of the UTC may be selected based on the fresh air heating needs of the building, the value of the electricity generated and the available building surfaces.     

Design,fabrication and performance evaluation of natural circulation rectangular box-type solar domestic water heating system

This study includes design and experimental analysis of a solar domestic water heating system. Water heating systems with glazed and unglazed collectors were constructed and tested at Dhaka, Bangladesh, at a latitude of 23.7 °N. Collector thermal efficiency and capability of raising water temperature were considered as performance evaluation measures. A typical day analysis showed that collector efficiency varied with time and touched its peak at around 12:00 h. During testing, the efficiency of the glazed collector increased by about 70.3% when compared with the unglazed collector. Average collector efficiency over the whole test period was also estimated to be 57.3% and 33.7% for glazed and unglazed collectors, respectively. Maximum water temperatures measured at daytime user outlets were, respectively, 82.4 °C and 65.5 °C for domestic water heating systems with glazed and unglazed collectors and approximated to be 49 °C and 32 °C higher than the ambient temperature. The glazed collector eventually offered significantly higher performances over the unglazed collector in improving system performance.     

Theoretical and experimental study of efficiency factor,heat transfer and thermal heat loss coefficients in solar air collectors with selective and nonselective absorbers

The thermal heat performance of a solar air collector depends strongly on the thermal heat loss and the efficiency factor. In order to increase these performances, it is necessary to use a solar air collector which is well insulated and where the fluid flow is fully developed turbulent flow. It needs a high heat transfer between the absorber plate and the fluid to decrease the absorber‐plate temperature and hence the heat loss by radiation from the absorber to the ambient. This increases the efficiency factor. In the present paper, the heat loss and efficiency factor are treated for solar air collectors with selective and nonselective absorber plate. It is shown that the selectivity of the absorber plate cannot play an important role in a well‐insulated solar collector with a fanned system which permits a fully developed turbulent flow and, in consequence, high heat transfer. Copyright © 1999 John Wiley & Sons, Ltd.     

Parametric study of a reverse flat plate absorber cabinet dryer: A new concept

In this communication, the concept of reverse flat plate collector has been used as a heating medium of air for the drying of agricultural products in a cabinet dryer. The reverse flat plate absorber is a non-concentrating collector which can collect solar heat at high temperature unlike conventional nonconcentrating collectors. The thermal performance of the proposed dryer is analyzed by solving the various energy balance equations. An attempt has been made to optimize the vent area of the dryer for speedy flow of humid air from the drying chamber to the atmosphere. In order to have parametric studies, numerical computations have been carried out for a typical day in June for Delhi climatic conditions. The performance of this system is compared with that of conventional cabinet dryers. It is found that the reverse flat plate absorber dryer gives the better performance.     

直通式真空管空气集热器热性能实验及干燥应用

在直通式太阳能玻璃真空管空气集热器基础上改进联箱结构,并搭建测试平台对该种改进型空气集热器进行热性能实验研究。通过实验比较改进前后集热器的温升和效率,获得改进后集热器出口温度与太阳辐照度关系的线性回归方程,掌握不同空气质量流量对集热器出口温度和集热效率的影响规律,分析得到该种真空管的最佳串联个数,并对应用该种集热器的太阳能干燥系统的干燥效果进行初步测试分析。该研究结果可为太阳能空气集热干燥系统的设计及应用提供参考。     

Solar collectors with colored absorbers

The integration of solar collectors in buildings should be compatible with the architectural design, and solar collectors with colored absorbers would be aesthetically preferable. In our laboratory we constructed and tested flat plate solar collectors with colored absorbers for water heating applications. The study includes collectors in their typical form with the protective glazing, and also collectors without glazing. Unglazed solar collectors are not widely used, although they are cost effective solar devices, suitable for low temperature thermal applications. We tested outdoors the constructed models, glazed and unglazed, with black, blue and red brown absorbers. In order to overcome the high thermal losses of the unglazed collectors and the low optical efficiency of the colored absorbers, we used flat booster reflectors. The additional solar radiation input from the reflectors increases the thermal energy output of the collectors, improving their performance. Theoretical steady state efficiency curves are also given for collectors with or without glazing. The presented experimental and theoretical results determine the range of the effective operation of the proposed solar collector types, which can be used in a variety of applications, instead of glazed or unglazed solar collectors with a black absorber.     

Thermal performance of solar air heaters: Mathematical model and solution procedure

A mathematical model and solution procedure for predicting the thermal performance of single-pass solar air collectors is presented. By omitting or providing a top glass cover over a plane absorber plate, or by providing a bottom plate under the absorber plate and circulating air over one or both of the air channels so formed, four common types of flat-plate solar air collector designs were considered. The surface temperatures of the walls surrounding the air streams were assumed uniform whereas the air temperatures were assumed to vary linearly along the collector. In the mathematical model, the solar collector was assumed sufficiently short for which the assumptions were valid. By considering a steady state heat transfer using the thermal network analysis procedure, a set of simultaneous equations for the mean temperature of the walls and the air streams were obtained. Instead of solving the simultaneous equations for mean temperatures explicitly, a matrix inversion method was employed using a standard sub-routine programme. Because heat transfer coefficients were temperature dependent, a set of mean temperatures was approximated which allowed the heat transfer coefficients to be evaluated as a first guess. An iterative process was then created that enabled the mean temperatures for the collector to be calculated. The newly-calculated mean temperatures were then compared with the initially-guessed temperatures. The iterative procedure was repeated until consecutive mean temperature values differed by less than 0.01°C. After this, another section of collector with a length equal to the previous one was added to the end of the first collector. The temperature conditions at the inlet of the second section were assumed equal to the outlet temperature conditions of the previous section. The iterative procedure to determine the mean temperatures was repeated for the next section. Additional sections were added until the required overall length of collector was considered. By this procedure, predictions of mean wall and air streams temperatures for a collector of any length could be obtained. Although only four, common single-pass types of flat-plate solar collectors are considered here, the solution procedure could be extended to encompass most other collector designs.     

Flat-plate solar-collector performance evaluation with a solar simulator as a basis for collector selection and performance prediction

The use of a solar simulator for performance determination permits collector testing under standard conditions of wind, ambient temperature, flow rate and “Sun”. The performance results determined with the simulator have been found to be in good agreement with outdoor performance results.This paper reports the measured thermal efficiency and evaluation of 23 collectors which differ according to absorber material (copper, aluminum, steel), absorber coating (nonselective black paint, selective copper oxide, selective black nickel, selective black chrome), type of glazing material (glass, Tedlar, Lexan, anti-reflection glass), the use of honeycomb material and the use of vacuum to reduce thermal convection losses. The collectors are given performance rankings based on noon-hour solar conditions and all-day solar conditions. The determination with the simulator of an all-day collector performance is made possible by tests at different incident angles. The solar performance rankings are made based on whether the collector is to be used for pool heating, hot water, absorption air conditioning, heating, or for a solar Rankine machine.Another test which aids in selecting collectors is a collector heat capacity test. This test permits a ranking of collectors according to their heat capacity (and time constant), which is a measure of the rapidity of a collector's response to transient solar conditions. Results are presented for such tests.Final considerations for collector selection would of course be made on the basis of cost and the reliability of performance over the required life of a collector. Results of a cost-effectiveness study is given for conditions corresponding to those required for absorption or heating. These results indicate that the additional cost involved in the upgrading of collector performance (selective surfaces, anti-reflection glass, etc.) appears to be cost effective and therefore justified. Some data are also presented to illustrate a method for the determination of outdoor performance degradation by use of simulator tests carried out before and after a period of outdoor operation.     

Performance analysis of a latent heat storage system with phase change material for new designed solar collectors in greenhouse heating

The continuous increase in the level of greenhouse gas emissions and the rise in fuel prices are the main driving forces behind the efforts for more effectively utilize various sources of renewable energy. In many parts of the world, direct solar radiation is considered to be one of the most prospective sources of energy. In this study, the thermal performance of a phase change thermal storage unit is analyzed and discussed. The storage unit is a component of ten pieced solar air collectors heating system being developed for space heating of a greenhouse and charging of PCM. CaCl₂6H₂O was used as PCM in thermal energy storage with a melting temperature of 29 °C. Hot air delivered by ten pieced solar air collector is passed through the PCM to charge the storage unit. The stored heat is utilized to heat ambient air before being admitted to a greenhouse. This study is based on experimental results of the PCM employed to analyze the transient thermal behavior of the storage unit during the charge and discharge periods. The proposed size of collectors integrated PCM provided about 18–23% of total daily thermal energy requirements of the greenhouse for 3–4 h, in comparison with the conventional heating device.     

波纹丝网型太阳能空气集热器热性能特性研究

提出一种新型波纹丝网型太阳能空气集热器,根据集热器的传热关系,用Matlab建立数学模型,并搭建实验系统进行测试,验证模型的准确性.利用模型研究关键结构参数和运行参数对集热器热性能的影响规律.结果表明:出口温度和集热量的模拟值与实验值最大偏差分别为2.3 K和443％,当温度系数介于0.01～0.05时,波纹丝网型太阳...     

Energy analysis and modeling of a solar assisted house heating system with a heat pump and an underground energy storage tank

An analytical model is presented and analyzed to predict the long term performance of a solar assisted house heating system with a heat pump and an underground spherical thermal energy storage tank. The system under investigation consists of a house, a heat pump, solar collectors and a storage tank. The present analytical model is based on a proper coupling of the individual energy models for the house, the heat pump, useful solar energy gain, and the transient heat transfer problem for the thermal energy storage tank. The transient heat transfer problem outside the energy storage tank is solved using a similarity transformation and Duhamel’s superposition principle. A computer code based on the present model is used to compute the performance parameters for the system under investigation. Results from the present study indicate that an operational time span of 5–7 years will be necessary before the system under investigation can attain an annually periodic operating condition. Results also indicate a decrease in the annually minimum value of the storage tank temperature with a decrease in the energy storage tank size and/or solar collector area.     

Simulation study of solar air heater

A mathematical model for predicting thermal efficiency, heat gain, and outlet air temperature of a covered plate attic solar collector under steady conditions was developed. The model presented in this paper utilizes the basic principles and relationships of heat transfer to simulate the behavior of the solar air heaters under various conditions. The model was validated by comparing the predicted outlet air temperatures and collector efficiencies to those measured during drying operation of an attic solar collector. The effect of the air speed inside the collector and wind speed above the collector on the collector efficiency were investigated using the mathematical model.     

Design and performance of an air collector for industrial crop dehydration

Test results are reported for the operation of unglazed and single-glazed solar collectors used to heat air to the 90°C (194°F) range. The collectors were constructed of standard black-painted metal decking and were tested in various lengths so that pressure drops and convective heat transfer rates could be varied independent of collector operation temperature. It is shown that the experimental collector performance results with single pass operation are in substantial agreement with standard collector analysis procedures. These results give a firm basis for collector and system optimization.     

A critical review of photovoltaic–thermal solar collectors for air heating

Integrated photovoltaic–thermal solar collectors have become of great interest in the solar thermal and photovoltaic (PV) research communities. Solar thermal systems and solar PV systems have each advanced markedly, and combining the two technologies provides the opportunity for increased efficiency and expanded utilization of solar energy. In this article, the authors critically review photovoltaic–thermal solar collectors for air heating. Included is a review of photovoltaic thermal technology and recent advances, particularly as applied to air heaters. It is determined that the photovoltaic–thermal (PV/T) air heater is or may in the future be practicable for preheating air for many applications, including space heating and drying, and that integrated PV/T collectors deliver more useful energy per unit collector area than separate PV and thermal systems. Although PV/T collectors are promising, it is evident that further research is required to improve efficiency, reduce costs and resolve several technical design issues related to the collectors.