倒装焊SnPb焊点热循环失效和底充胶的影响

采用实验方法 ,确定了倒装焊 Sn Pb焊点的热循环寿命 .采用粘塑性和粘弹性材料模式描述了 Sn Pb焊料和底充胶的力学行为 ,用有限元方法模拟了 Sn Pb焊点在热循环条件下的应力应变过程 .基于计算的塑性应变范围和实验的热循环寿命 ,确定了倒装焊 Sn Pb焊点热循环失效 Coffin- Manson经验方程的材料参数 .研究表明 ,有底充胶倒装焊 Sn Pb焊点的塑性应变范围比无底充胶时明显减小 ,热循环寿命可提高约 2 0倍 ,充胶后的焊点高度对可靠性的影响变得不明显     

倒装焊封装中无铅焊点在封装工艺中的热机械力学分析

采用粘塑性Garofalo—Arrhenius模型描述无铅焊料的蠕变行为，确定了96．5Sn3.5Ag焊点材料的模型参数。采用与固化过程相关的粘弹性力学模型描述倒装焊底充胶的力学行为。利用有限元法模拟了无铅板上倒装焊在封装工艺及热循环条件下的应力应变行为。结果表明由于无铅技术在封装中的引入，封装工艺对倒装焊器件的影响更为重要。     

湿热环境下倒装焊无铅焊点的可靠性

对板上倒装芯片底充胶进行吸湿实验,并结合有限元分析软件研究了底充胶在湿敏感元件实验标准MSL—1条件下吸湿和热循环阶段的解吸附过程,测定了湿热环境对Sn3.8Ag0.7Cu焊料焊点可靠性的影响,并用蠕变变形预测了无铅焊点的疲劳寿命。结果表明:在湿热环境下,底充胶材料内部残留的湿气提高了焊点的应力水平。当分别采用累积蠕变应变和累积蠕变应变能量密度寿命预测模型时,无铅焊点的寿命只有1740和1866次循环周期。     

倒装焊焊点形态及其可靠性研究

本文采用Surface Evolver软件对倒装焊复合焊点的几何形态进行了模拟。通过非线性有限元方法研究有铅和无铅两种焊点在热循环作用下的应力应变关系，基于疲劳寿命C—M预测公式对焊点的热疲劳寿命进行预测与比较。     

倒装焊中复合SnPb焊点形态模拟

本文给出了倒装焊(flip-chip)焊点形态的能量控制方程,采用Surface Evolver软件模拟了倒装焊复合SnPb焊点(高Pb焊料凸点,共晶SnPb焊料焊点)的三维形态.利用焊点形态模拟的数据,分析了芯片和基板之间SnPb焊点的高度与焊点设计和焊接工艺参数的关系.研究表明:共晶SnPb焊料量存在临界值,当共晶SnPb焊料量小于临界值时,焊点的高度等于芯片上高Pb焊料凸点的半径值;当共晶SnPb焊料量大于临界值时,焊点的高度随共晶SnPb焊料量的增加而增加.另外,采用无量纲的形式给出了焊点高度与共晶焊料量、焊盘尺寸、芯片凸点的尺寸,芯片重量之间的关系模型,研究结果对倒装焊焊点形态的控制、工艺参数的优化和提高焊点可靠性具有指导意义.     

球栅阵列封装中SnPb焊点的应力应变分析

基于SnPb焊料的统一粘塑性Anand本构模型,运用ANSYS有限元软件分析了球栅阵列封装中复合SnPb焊点在热循环过程中的应力、应变的分布,观察到SnPb焊料的蠕变行为和应力松弛现象,结果证明:外侧焊点经受的应力、应变范围比内侧焊点大;焊点的最高应力区域出现在Sn60Pb40焊料的最外缘处,最高应变区域出现在Pb90Sn10焊料与UBM层接触面的最上缘处.     

不同基板的CBGA焊点在热循环下的力学特性研究

采用粘塑性本构Anand方程描述SnPb钎料的变形行为,用有限元方法对CBGA组件焊点结构进行二维模型分析;同时,选用不同的基板材料(Al2O3、AlN、SiC),考察焊点在热循环加载过程中的应力应变等力学行为.研究结果表明,最外侧焊点受到的应力应变最大,所以裂纹最有可能从最外侧焊点处萌生,并沿着基板一侧扩展;焊点的高应力发生在热循环的低温阶段,升降温过程中的蠕变和非弹性应变的累积显著,应力应变迟滞环在热循环的最初几个周期内就能很快稳定.模拟结果得出,采用BeO基板材料时焊点的应力应变最小,其可靠性最高.     

凸点材料的选择对器件疲劳特性的影响

为了研究凸点材料对器件疲劳特性的影响,采用非线性有限元分析方法、统一型黏塑性本构方程和Coffin-Manson修正方程,对Sn3.0Ag0.5Cu,Sn63Pb37和Pb90Sn10三种凸点材料倒装焊器件的热疲劳特性进行了系统研究,对三种凸点的疲劳寿命进行了预测,并对Sn3.0Ag0.5Cu和Pb90Sn10两种凸点材料倒装焊器件进行了温度循环试验.结果表明,仿真结果与试验结果基本吻合.在热循环过程中,凸点阵列中距离器件中心最远的焊点,应力和应变变化最剧烈,需重点关注这些危险焊点的可靠性;含铅凸点的热疲劳特性较无铅凸点更好,更适合应用于高可靠的场合;而且随着铅含量的增加,凸点的热疲劳特性越好,疲劳寿命越长.     

材料模式选择对SMT焊点寿命分析的影响

通过对SnPb钎料在弹塑性与蠕变，弹性与黏塑性两种材料模式下受热循环作用产生应力应变的有限元仿真。讨论了材料模式对SMT焊点寿命分析的影响。     

底充胶固化工艺对低k倒装焊器件可靠性的影响

利用四点弯曲实验测试了一组芯片(30片)的强度,使用威布尔统计模型描述了芯片失效率的分布,预测了在后续热循环过程中芯片的失效概率。通过有限元软件研究了底充胶固化工艺对芯片上方垂直开裂应力、焊点等效塑性应变及低k层最大等效应力的影响。结果表明:与未经固化的相比,底充胶固化工艺使得芯片的失效率从0.08%增大到0.37%,焊点的等效塑性应变增大约7倍,低k层的最大等效应力增大约18%。     

The effects of underfill and its material models onthermomechanical behaviors of a flip chip package

In this paper, the effects of underfill on thermomechanical behavior of two types of flip chip packages with different bumping size and stand-off height were investigated under thermal cycling both experimentally and two-dimensional (2-D) finite element simulation. The materials inelasticity, i.e., viscoelasticity of underfill U8437-3 and viscoplasticity of 60 Sn40 Pb solder, were considered in the simulations. The results show that the use of underfill encapsulant increases tremendously (~20 times) the thermal fatigue lifetime of SnPb solder joint, weakens the effects of stand-off height on the reliability, and changes the deformation mode of the package. It was found that the thermal fatigue crack occurs in the region with maximum plastic strain range, and the Coffin-Manson type equation could then be used for both packages with and without underfill. Solder joint crack initiation occurred before delamination when using underfill with good adhesion (75 MPa) and the underfill delamination may not be a dominant failure mode in the present study. The interfacial stresses at the underfill/chip interface were calculated to analyze delamination sites, which agree with the results from acoustic image. Moreover, the effects of material models of underfill, i.e., constant elasticity (EC) and temperature dependent elasticity (ET) as well as the viscoelasticity (VE), on the thermomechanical behaviors of flip chip package were also studied in the simulation. The VE model gives comparatively large plastic strain range and large displacements in the shear direction, as well as decreased solders joint lifetime. The ET model gives similar results as the VE model and could be used instead of VE in simulations for the purpose of simplicity     

Parametric reliability analysis of no-underfill flip chip package

This research proposes a parametric analysis for a flip chip package with a constraint-layer structure. Previous research has shown that flip-chip type packages with organic substrates require underfill for achieving adequate reliability life. Although underfill encapsulant is needed to improve the reliability of flip chip solder joint interconnects, it will also increase the difficulty of reworkability, increase the packaging cost and decrease the manufacturing throughput. This research is based on the fact that if the thermal mismatch between the silicon die and the organic substrate could be minimized, then the reliability of the solder joint could be accordingly enhanced. This research proposes a structure using a ceramic-like material with CTE close to silicon, mounted on the backside of the substrate to constrain the thermal expansion of the organic substrate. The ceramic-like material could reduce the thermal mismatch between silicon die and substrate, thereby enhancing the reliability life of the solder joint. Furthermore, in order to achieve better reliability design of this flip chip package, a parametric analysis using finite element analysis is performed for package design. The design parameters of the flip chip package include die size, substrate size/material, and constraint-layer size/material, etc. The results show that this constraint-layer structure could make the solder joints of the package achieve the same range of reliability as the conventional underfill material. More importantly, the flip chip package without underfill material could easily solve the reworkability problem, enhance the thermal dissipation capability and also improve the manufacturing throughput     

Reliability analysis and design for the fine-pitch flip chip BGA packaging

The geometry of solder joints in the flip chip technologies is primarily determined by the associated solder volume and die/substrate-side pad size. In this study, the effect of these parameters on the solder joint reliability of a fine-pitched flip chip ball grid array (FCBGA) package is extensively investigated through finite element (FE) modeling and experimental testing. To facilitate thermal cycling (TC) testing, a simplified FCBGA test vehicle with a very high pin counts (i.e., 2499 FC solder joints) is designed and fabricated. By the vehicle, three different structural designs of flip chip solder joints, each of which consists of a different combination of these design parameters, are involved in the investigation. Furthermore, the associated FE models are constructed based on the predicted geometry of solder joints using a force-balanced analytical approach. By way of the predicted solder joint geometry, a simple design rule is created for readily and qualitatively assessing the reliability performance of solder joints during the initial design stage. The validity of the FE modeling is extensively demonstrated through typical accelerated thermal cycling (ATC) testing. To facilitate the testing, a daisy chain circuit is designed, and fabricated in the package for electrical resistance measurement. Finally, based on the validated FE modeling, parametric design of solder joint reliability is performed associated with a variety of die-side pad sizes. The results show that both the die/substrate-side pad size and underfill do play a significant role in solder joint reliability. The derived results demonstrate the applicability and validity of the proposed simple design rule. It is more surprising to find that the effect of the contact angle in flip chip solder joint reliability is less significant as compared to that of the standoff height when the underfill is included in the package.     

Thermal cycling reliability of SnAgCu and SnPb solder joints: A comparison for several IC-packages

This paper deals with a comparison study between SnPb and SnAgCu solder joint reliability. The comparison is based on non-linear finite element modelling. Three packages have been selected: silicon CSP, underfilled flip chip and QFN package. Also the effect of thermal cycling conditions has been investigated. Comparing the induced inelastic strains in the solder joint, the lead-free SnAgCu generally scores better thanks to the lower creep strain rate. On the other hand for the CSP and flip chip package, SnAgCu scores worse for the more extreme loading conditions when the inelastic dissipated energy density is selected as damage parameter. The main reason is that due to the lower creep strain rate, the stresses become higher for SnAgCu resulting in higher hysteresis loops with more dissipated energy per cycle. For the QFN package, SnAgCu scores much better.     

Influence of underfill materials on the reliability of coreless flip chip package

A flip chip package was assembled by using 6-layer laminated polyimide coreless substrate, eutectic Sn37Pb solder bump, two kinds of underfill materials and Sn_3.0Ag_0.5Cu solder balls. Regarding to the yield, the peripheral solder joints were often found not to connect with the substrate due to the warpage at high temperature, modification of reflow profile was benefit to improve this issue. All the samples passed the moisture sensitive level test with a peak temperature of 260 °C and no delamination at the interface of underfill and substrate was found. In order to know the reliability of coreless flip chip package, five test items including temperature cycle test (TCT), thermal shock test (TST), highly accelerated stress test (HAST), high temperature storage test (HTST) and thermal humidity storage test (THST) were done. Both of the two underfill materials could make the samples pass the HTST and THST, however, in the case of TCT, TST and HAST, the reliability of coreless flip chip package was dominated by underfill material. A higher Young’s modules of underfill, the more die crack failures were found. Choosing a correct underfill material was the key factor for volume production of coreless flip chip package.     

Dependence of Flip Chip Solder Reliability on Filler Settling

Thermomechanical reliability of solder joints in flip-chip packages is usually analyzed by assuming a homogeneous underfill ignoring the settling of filler particles. However, filler settling does impact flip chip reliability. This paper reports a numerical study of the influence of filler settling on the fatigue estimation of flip-chip solder joints. In total, nine underfill materials ( 35 vol% silica filler in three epoxies with three filler settling profiles for each epoxy) are individually introduced in a 2-D finite element (FE) model to compare the thermal response of flip chip solder joints that are surrounded by the underfill. The results show that the fatigue indicators for the solder joints (inelastic shear strain increments and inelastic shear strain energy density) corresponding to a gradual, nonuniform filler profile studied in this paper can be smaller than those associated with the uniform filler profile, suggesting that certain gradual filler settling profiles in conjunction with certain resin grades may favor a longer solder fatigue lifetime. The origin of this intriguing observation is in the fact that the solder fatigue indicators are a function of the thermal mismatch among the die, substrate, solder, and underfill materials. The thermal mechanics interplayed among these materials along with a gradual filler profile may allow for minimizing thermal mismatch; and thus lead to lower fatigue indicators.      

Mechanical loading of flip chip joints before underfill: the impact on yield and reliability

The underfill-facilitated migration from ceramic to lower cost laminate substrates has become a powerful enabler of direct chip attach by offering lower cost, greater electrical functionality, and a smaller system footprint over comparable packaging technologies. Once underfilled, flip chip on laminate has proven extremely reliable even in severe automotive environments. However, between the process steps of reflow and underfill cure, unprotected flip chip solder joints assembled to laminate boards are susceptible to damage and breakage if mishandled. Here, the survivability and long-term reliability of flip chip joints was studied over a range of applied strains. Mechanical loading of joints was applied via beam deflections of populated, but nonunderfilled, laminate boards. Electrical continuity was monitored before and after testing to determine when the load applied to the flip chip exceeded the joint fracture strength. The propensity for solder joint fracture was then calculated as a function of solder bump size and also as a function of strain rate. Analysis of the mechanical properties of solder revealed assembly strategies which reduce bump damage and eliminate yield loss during the process steps leading up to underfill cure. Both strained and unstrained units were then underfilled and cycled between −50 and +150 °C. While mechanical damage was evident in bump cross-sections of strained flip chip assemblies, the fatigue lives of underfilled solder joints were found to be independent of the size of mechanical loads applied before underfill.     

The effects of underfill on the reliability of flip chip solder joints

Thermal fatigue damage of flip chip solder joints is a serious reliability concern, although it usually remains tolerable with the flip chip connections (of smaller chips) to ceramic boards as practiced by IBM for over a quarter century. However, the recent trend in microelectronics packaging towards bonding large chips or ceramic modules to organic boards means a larger differential thermal expansion mismatch between the board and the chip or ceramic module. To reduce the thermal stresses and strains at solder joints, a polymer underfill is customarily added to fill the cavity between the chip or module and the organic board. This procedure has typically at least resulted in an increase of the thermal fatigue life by a factor of 10, as compared to the non-underfilled case. In this contribution, we first discuss the effects of the underfill to reduce solder joint stresses and strains, as well as underfill effects on fatigue crack propagation based on a finite element analysis. Secondly, we probe the question of the importance of the effects of underfill defects, particularly that of its delamination from the chip side, on the effectiveness of the underfill to increase thermal fatigue life. Finally, we review recent experimental evidence from thermal cycling of actual flip chip modules which appears to support the predictions of our model.