Photoluminescence studies of In0.7Al0.3As/In0.75Ga0.25As/In0.7Al0.3As metamorphic heterostructures on GaAs substrates

The influence of the design of the metamorphic buffer of In_0.7Al_0.3As/In_0.75Ga_0.25As metamorphic nanoheterostructures for high-electron-mobility transistors (HEMTs) on their electrical parameters and photoluminescence properties is studied experimentally. The heterostructures are grown by molecular-beam epitaxy on GaAs (100) substrates with linear or step-graded In _x Al_{1 ? x} As metamorphic buffers. For the samples with a linear metamorphic buffer, strain-compensated superlattices or inverse steps are incorporated into the buffer. At photon energies ?ω in the range 0.6–0.8 eV, the photoluminescence spectra of all of the samples are identical and correspond to transitions from the first and second electron subbands to the heavy-hole band in the In_0.75Ga_0.25As/In_0.7Al_0.3As quantum well. It is found that the full width at half-maximum of the corresponding peak is proportional to the two-dimensional electron concentration and the luminescence intensity increases with increasing Hall mobility in the heterostructures. At photon energies ?ω in the range 0.8–1.3 eV corresponding to the recombination of charge carriers in the InAlAs barrier region, some features are observed in the photoluminescence spectra. These features are due to the difference between the indium profiles in the smoothing and lower barrier layers of the samples. In turn, the difference arises from the different designs of the metamorphic buffer.     

Effect of GaAs (100) substrate misorientation on the electrical parameters and surface morphology of metamorphic In0.7Al0.3As/In0.75Ga0.25As/In0.7Al0.3As HEMT nanoheterostructures

The results of studies of the effect of GaAs (100) substrate misorientation on the electrical parameters and surface morphology of high electron mobility In_0.7Al_0.3As/In_0.75Ga_0.25As/In_0.7Al_0.3As/GaAs nanoheterostructures are reported. Using molecular-beam epitaxy, two identical structures with a stepped compositional profile of the metamorphic In _x Al_{1 ? x} As (Δ _x = 0.05) buffer are grown on substrates of two types: a singular GaAs substrate with the orientation (100) ± 0.5° and a GaAs (100) substrate misoriented by (2 ± 0.5)° in the $\left[ {0\bar 1\bar 1} \right]$ direction. It is found that, in the case of the misoriented substrate, the concentration of the two-dimensional electron gas is ～40% higher. Broadening of the photoluminescence spectra and a shift of the peaks to lower photon energies, as experimentally observed in the case of the misoriented substrate, are attributed to the increased roughness of the heterointerfaces and strengthened fluctuations of the quantum-well width.     

120-nm gate-length In0.7Ga0.3As/In0.52Al0.48As InP-based HEMT

120 nm gate-length In_(0.7)Ga_(0.3)As/In_(0.52)Al_(0.48) As InP-based high electron mobility transitions(HEMTs) are fabricated by a new T-shaped gate electron beam lithograph(EBL) technology,which is achieved by the use of a PMMA/PMGI/ZEP520/PMGI four-layer photoresistor stack.These devices also demonstrate excellent DC and RF characteristics:the transconductance,maximum saturation drain-to-source current,threshold voltage,maximum current gain frequency,and maximum power-gain cutoff frequency of InGaAs/I...     

Very low-noise Al/sub 0.3/Ga/sub 0.7/As/Ga/sub 0.65/In/sub 0.35/As/GaAs single quantum-well pseudomorphic HEMTs

AlGaAs/GaInAs/GaAs pseudomorphic HEMTs with an InAs mole fraction as high as 35% in the channel has been successfully fabricated. The device exhibits a maximum extrinsic transconductance of 700 mS/mm. At 18 GHz, a minimum noise figure of 0.55 dB with 15.0 dB associated gain was measured. At 60 GHz, a minimum noise figure as low as 1.6 dB with 7.6 dB associated gain was also obtained. This is the best noise performance yet reported for GaAs-based HEMTs.<>     

0.5 mu m gate length InP/In/sub 0.75/Ga/sub 0.25/As/InP pseudomorphic HEMT with high DC and RF performance

High performance InP/In/sub 0.75/Ga/sub 0.25/As/InP pseudomorphic double heterojunction (DH) HEMTs with a gate length of 0.5 mu m are reported. Both DC and RF characteristics of this new type of Al-free HEMT demonstrate its suitability for microwave applications.<>     

掺杂GaAs/Al0.3Ga0.7As超晶格的光致发光特性分析

在室温下,通过光致发光实验研究了用MBE生长的GaAs/Al0.3Ga0.7As超晶格材料的光致发光特性,对测得的发光峰进行了指认.理论计算和实验结果符合很好.     

Performance improvement in tensile-strained In/sub 0.5/Al/sub 0.5/As/In/sub x/Ga/sub 1-x/As/In/sub 0.5/Al/sub 0.5/As metamorphic HEMT

This paper proposes a In/sub 0.5/Al/sub 0.5/As/In/sub x/Ga/sub 1-x/As/In/sub 0.5/Al/sub 0.5/As (x=0.3-0.5-0.3) metamorphic high-electron mobility transistor with tensile-strained channel. The tensile-strained channel structure exhibits significant improvements in dc and RF characteristics, including extrinsic transconductance, current driving capability, thermal stability, unity-gain cutoff frequency, maximum oscillation frequency, output power, power gain, and power added efficiency.     

Optimization of the In0.3Ga0.7As-Layer Thickness in a Triple-Junction In0.3Ga0.7As/GaAs/In0.5Ga0.5P Solar Cell

Semiconductors - The optimum absorbing-layer thickness in the bottom In0.3Ga0.7As subcell of a triple-junction In0.3Ga0.7As/GaAs/In0.5Ga0.5P solar cell is sought for using the Sentaurus TCAD...     

InAs/GaAs quantum dot infrared photodetector (QDIP) with double Al/sub 0.3/Ga/sub 0.7/As blocking barriers

The ten stacked self-assembled InAs/GaAs quantum dot infrared photodetectors (QDIP) with different Al/sub 0.3/Ga/sub 0.7/As barrier widths and growth temperatures were prepared. Asymmetric current-voltage (I-V) characteristics and 2/spl sim/7.5 /spl mu/m detection window were observed. Peak responsivity of 84 mA/W at -0.4 V and peak specific detectivity of 2.5/spl times/10/sup 9/ cm-Hz/sup 1/2//W at zero bias were observed at 50 K. The characteristics of polarization insensitivity over the incident light and the high background photocurrent suggest that the self-assembled QDIP can be operated at higher temperature (/spl sim/250 K) under normal incidence condition in contrast to quantum well infrared photodetector (QWIP).     

60-GHz high power performance In/sub 0.35/Al/sub 0.65/As-In/sub 0-35/Ga/sub 0.65/As metamorphic HEMTs on GaAs

We report on a double-pulse doped, double recess In/sub 0.35/Al/sub 0.65/As-In/sub 0.35/Ga/sub 0.65/As metamorphic high electron mobility transistor (MHEMT) on GaAs substrate. This 0.15-/spl mu/m gate MHEMT exhibits excellent de characteristics, high current density of 750 mA/mm, extrinsic transconductance of 700 mS/mm. The on and off state breakdown are respectively of 5 and 13 V and defined It gate current density of 1 mA/mm. Power measurements at 60 GHz were performed on these devices. Biased between 2 and 5 V, they demonstrated a maximum output power of 390 mW/mm at 3.1 V of drain voltage with 2.8 dB power gain and a power added efficiency (PAE) of 18%. The output power at 1 dB gain compression is still of 300 mW/mm. Moreover, the linear power gain is of 5.2 dB. This is to our knowledge the best output power density of any MHEMT reported at this frequency.     

Pseudomorphic In/sub 0.52/Al/sub 0.48/As/In/sub 0.7/Ga/sub 0.3/As HEMTs with an ultrahigh f/sub T/ of 562 GHz

We fabricated decananometer-gate pseudomorphic In/sub 0.52/Al/sub 0.48/As/In/sub 0.7/Ga/sub 0.3/As high-electron mobility transistors (HEMTs) with a very short gate-channel distance. We obtained a cutoff frequency f/sub T/ of 562 GHz for a 25-nm-gate HEMT. This f/sub T/ is the highest value ever reported for any transistor. The ultrahigh f/sub T/ of our HEMT can be explained by an enhanced electron velocity under the gate, which was a result of reducing the gate-channel distance.     

GaAs/Al0.3Ga0.7As 量子阱红外探测器光谱特性研究

采用金属有机物化学气相沉积法(MOCVD)生长GaAs/Al0.3Ga0.7As量子阱材料,制备300 m300 m台面,内电极压焊点面积为20 m20 m,外电极压焊点面积为80 m80 m单元量子阱器件两种。利用傅里叶光谱仪对1#,2#样品进行77K液氮温度光谱响应测试。实验结果显示1#,2#样品峰值响应波长分别为8.43 m,8.32 m,与根据薛定谔方程得到器件理论峰值波长8.5 m间误差分别为1.0%,2.1%。实验结果说明MOCVD技术可以满足QWIP生长制备工艺要求,且器件电极压焊点位置与面积大小对器件峰值波长影响不大,而对峰值电流有一定影响。     

High-temperature thermal stability performance in /spl delta/-doped In/sub 0.425/Al/sub 0.575/As--In/sub 0.65/Ga/sub 0.35/As metamorphic HEMT

We report, to our knowledge, the best high-temperature characteristics and thermal stability of a novel /spl delta/-doped In/sub 0.425/Al/sub 0.575/As--In/sub 0.65/Ga/sub 0.35/As--GaAs metamorphic high-electron mobility transistor. High-temperature device characteristics, including extrinsic transconductance (g/sub m/), drain saturation current density (I/sub DSS/), on/off-state breakdown voltages (BV/sub on//BV/sub GD/), turn-on voltage (V/sub on/), and the gate-voltage swing have been extensively investigated for the gate dimensions of 0.65/spl times/200 /spl mu/m/sup 2/. The cutoff frequency (f/sub T/) and maximum oscillation frequency (f/sub max/), at 300 K, are 55.4 and 77.5 GHz at V/sub DS/=2 V, respectively. Moreover, the distinguished positive thermal threshold coefficient (/spl part/V/sub th///spl part/T) is superiorly as low as to 0.45 mV/K.     

Hot-hole lateral transport in a two-dimensional GaAs/Al0.3Ga0.7As structure

A narrow peak at the leading edge of the current pulse was found in samples of p-GaAs/Al_0.3Ga_0.7As structures subjected to a high electric field. An analysis of the shape and height of the peak as a function of the electric field, as well as the field redistribution along the sample, allows us to conclude that domain instability exists under these conditions. It is also shown that the energy of holes heated in moderate electric fields can significantly exceed the optical phonon energy.     

Ultralow leakage In/sub 0.53/Ga/sub 0.47/As p-i-n photodetector grown on linearly graded metamorphic In/sub x/Ga/sub 1-x/P buffered GaAs substrate

A novel top-illuminated In/sub 0.53/Ga/sub 0.47/As p-i-n photodiodes (MM-PINPD) grown on GaAs substrate by using linearly graded metamorphic In/sub x/Ga/sub 1-x/P (x graded from 0.49 to 1) buffer layer is reported. The dark current, optical responsivities, noise equivalent power, and operational bandwidth of the MM-PINPD with aperture diameter of 60 /spl mu/m are 13 pA, 0.6 A/W, 3.4/spl times/10/sup -15/ W/Hz/sup 1/2/, and 7.5 GHz, respectively, at 1550 nm. The performances of the MM-PINPD on GaAs are demonstrated to be comparable to those of a similar device made on InGaAs-InP substrate.     

MOVPE grown Ga/sub 0.6/In/sub 0.4/Sb photodiodes for 2.55 mu m detection

Photodiodes with a long-wavelength cutoff extending out of 2.9 mu m have been fabricated from MOVPE-grown Ga/sub 0.6/In/sub 0.4/Sb homojunctions. These mesa devices without any passivation or antireflecting coating exhibit a peak efficiency as high as 43% at 2.60 mu m.<>     

The microwave power performance comparisons of Al/sub x/Ga/sub 1-x/As/In/sub 0.15/Ga/sub 0.85/As (x=0.3, 0.5, 0.7, 1.0) doped-channel HFETs

The properties of doped-channel field-effect transistors (DCFET) have been thoroughly investigated on Al/sub x/Ga/sub 1-x/As/InGaAs (x= 0.3, 0.5, 0.7, 1) heterostructures with various Al mole fractions. In this study, we observed that by introducing a 200-/spl Aring/-thick Al/sub 0.5/Ga/sub 0.5/As (x=0.5) Schottky layer can enhance the device power performance, as compared with the conventional x=0.3 AlGaAs composition system. However, a degradation of the device power performance was observed for further increasing the Al mole fractions owing to their high sheet resistance and surface states. Therefore, Al/sub 0.5/Ga/sub 0.5/As Schottky layer design provides a good opportunity to develop a high power device for power amplifier applications.     

A new Pd-oxide-Al/sub 0.3/Ga/sub 0.7/As MOS hydrogen sensor

A new and interesting Pd-oxide-Al/sub 0.3/Ga/sub 0.7/As MOS hydrogen sensor has been fabricated and studied. The steady-state and transient responses with different hydrogen concentrations has been measured at various temperatures. Based on the large Schottky barrier height and presence of oxide layer, the studied device exhibits a high hydrogen detection sensitivity and wide temperature operating regime. The studied device exhibits the low-leakage current and obvious current changes when exposed to hydrogen-contained gas. Even at room temperature, a very high hydrogen detection sensitivity of 155.9 is obtained when a 9090 ppm H/sub 2//air gas is introduced. Furthermore, when exposed to hydrogen-contained gas at 95/spl deg/C, both the forward and reverse currents are substantially increased with increased hydrogen concentration. In other words, the studied device can be used as a hydrogen sensor under the applied bidirectional bias. Under the applied voltage of 0.35 V and 9090 ppm H/sub 2//air hydrogen ambient, a fast adsorption response time about 10 s is found. The transient and steady-state characteristics of hydrogen adsorption are also investigated.     

Persistent photo-conductance and photoquenching of selectively doped Al0.3Ga0.7As GaAs/heterojunctions

The dependence on photon energy of the persistent photoconductivity (PPC) in selectively doped high mobility Al_0.3Ga_0.7As—GaAs heterostructures has been measured at temperatures below 80 K. A decrease in conductivity due to light exposure at one wavelength after exposure to light at another wavelength — photo-quenching — is also found. It is concluded that deep centers in GaAs and AlGaAs other than the DX center in AlGaAs are mainly responsible for PPC.     

Device linearity comparison of uniformly doped and /spl delta/-doped In/sub 0.52/Al/sub 0.48/As/In/sub 0.6/Ga/sub 0.4/As metamorphic HEMTs

The uniformly doped and the /spl delta/-doped In/sub 0.52/Al/sub 0.48/As/In/sub 0.6/Ga/sub 0.4/As metamorphic high-electron mobility transistors (MHEMTs) were fabricated, and the dc characteristics and the third-order intercept point (IP3) of these devices were measured and compared. Due to more uniform electron distribution in the quantum-well region, the uniformly doped MHEMT exhibits a flatter transconductance (G/sub m/) versus drain-to-source current (I/sub DS/) curve and much better linearity with higher IP3 and higher IP3-to-P/sub dc/ ratio as compared to the /spl delta/-doped MHEMT, even though the /spl delta/-doped device exhibits higher peak transconductance. As a result, the uniformly doped MHEMT is more suitable for communication systems that require high linearity operation.