Single-Calcination Synthesis of Pyrochlore-Free 0.9Pb(Mg1/3Nb2/3)O3–0.1PbTiO3 and Pb(Mg1/3Nb2/3)O3 Ceramics Using a Coating Method

A coating approach for synthesizing 0.9Pb(Mg_1/3Nb_2/3)O₃–0.1PbTiO₃ (0.9PMN–0.1PT) and PMN using a single calcination step was demonstrated. The pyrochlore phase was prevented by coating Mg(OH)₂ on Nb₂O₅ particles. Coating of Mg(OH)₂ on Nb₂O₅ was done by precipitating Mg(OH)₂ in an aqueous Nb₂O₅ suspension at pH 10. The coating was confirmed using optical micrographs and zeta-potential measurements. A single calcination treatment of the Mg(OH)₂-coated Nb₂O₅ particles mixed with appropriate amounts of PbO and PbTiO₃ powders at 900°C for 2 h produced pyrochlore-free perovskite 0.9PMN–0.1PT and PMN powders. The elimination of the pyrochlore phase was attributed to the separation of PbO and Nb₂O₅ by the Mg(OH)₂ coating. The Mg(OH)₂ coating on the Nb₂O₅ improved the mixing of Mg(OH)₂ and Nb₂O₅ and decreased the temperature for complete columbite conversion to ∼850°C. The pyrochlore-free perovskite 0.9PMN–0.1PT powders were sintered to 97% density at 1150°C. The sintered 0.9PMN–0.1PT ceramics exhibited a dielectric constant maximum of ∼24 660 at 45°C at a frequency of 1 kHz.     

Low-Temperature, Single Step, Reactive Sintering of Lead Magnesium Niobate Using Mg(OH)2-Coated Nb2O5 Powders

A low-temperature, single step, reactive sintering method for Pb(Mg_1/3Nb_2/3)O₃ (PMN) and PMN–PbTiO₃ (PMN–PT) processing was developed based on the coating of Mg(OH)₂ on Nb₂O₅. This method simplified the processing of PMN and PMN–PT to a single step of heat-treatment and decreased the sintering temperature to 1000°C. It was found that the pyrochlore phase formation reaction at 500°C reduced the particle size to 130 nm. The overlap of the pyrochlor-perovskite phase transformation between 700° and 900°C and the densification process between 800° and 1000°C improved the sintering process. These two factors were the major reasons of the low temperature sintering.     

New Preparation Method of Low-Temperature-Sinterable Perovskite 0.9Pb(Mg1/3Nb2/3)O3-0.1PbTiO3 Powder and Its Dielectric Properties

A relaxor ferroelectric material, 0.9Pb(Mg_1/3Nb_2/3)O₃-0.1PbTiO₃ (0.9PMN-0.1PT) with a pyrochlore-free phase, was prepared by using one-step calcination in the present study. The 0.9PMN-0.1PT powder with the pure perovskite phase was prepared successfully from a mixture of the PMN precursor and the crystalline PT by heating for 2 h at temperatures greaterthan equal to750°C. The PMN precursor was synthesized by adding an aqueous Mg(NO₃)₂ solution, rather than MgO, to the alcoholic slurry of PbO and Nb₂O₅. The 0.9PMN-0.1PT powder sintered to >96% relative density via heat treatment for 2 h at temperatures of 900°-1200°C. The highest room-temperature dielectric constant (epsilon_rt) was 24700 at 1 kHz for the samples that were sintered at 1100°C; however, the samples that were sintered at 900°C still had epsilon_rt values of 22600 at 1 kHz.     

Preparation and Characterization of Relaxor Ferroelectric 0.65Pb(Mg1/3Nb2/3)O3–0.35PbTiO3 by a Polymerizable Complex Method

A modified polymerizable complex (PC) method for the preparation of the relaxor ferroelectric 0.65Pb(Mg_1/3Nb_2/3)O₃–0.35PbTiO₃ (PMN–PT) ceramics has been developed using a novel water-soluble Nb precursor. The effects of Pb content and sintering temperature on the structure, morphology, composition, and electrical properties of PMN–PT powders and ceramics were investigated systematically. It was found that the modified PC method could effectively reduce the initial crystallization temperature of the perovskite phase to 500°C. For PMN–PT samples with 15% excess Pb content sintered at 600°C for 2 h, the 87% perovskite phase can be achieved, which is much higher than that in conventional solid-state reactions and other solution-based methods at the same temperature. On further increasing the sintering temperature to 1100°C, the perovskite phase content basically remains constant. This is attributed to the Pb-deficient pyrochlore phase formation. On increasing the sintering temperature to 1250°C, the dielectric constant and remnant polarization of PMN–PT ceramics significantly improved due to the larger grain sizes, enhanced density, and the decreasing pyrochlore phase. PMN–PT ceramics with a 98.5% content of the perovskite phase have been fabricated at 1250°C. It displays typical ferroelectric relaxor characteristics with a remnant polarization of 18 μC/cm², a coercive field of 9.6 kV/cm, a piezoelectric coefficient of d ₃₃=360 pC/N, and room-temperature and maximum dielectric constants of 3600 and 10 500 at 1 kHz, respectively.     

Processing and Electrical Properties in Lead-Based (Pb(Mg1/3Nb2/3)O3, Pb(Yb1/2Nb1/2)O3, PbTiO3) Systems

Lead-based ferroelectric (FE) ceramics exhibit superior electromechanical properties; therefore, there has been an increased focus on developing new lead-based FE materials with high Curie temperature ( T _c) and enhanced properties. The aim of this study was to investigate new compositions in the Pb(Mg_1/3Nb_2/3)O₃–Pb(Yb_1/2Nb_1/2)O₃–PbTiO₃ ( PMN–PYbN–PT) system to enhance the electromechanical properties while increasing the T _c and lowering the sintering temperature. The 0.575[0.5PMN–0.5PYbN]–0.425PT composition at PMN/PYbN (50/50) mole ratio were prepared by reactive sintering PMNT and PYbNT powder mixtures at 950°–1200°C for 4 h. PMNT and PYbNT powders were calcined via the columbite method. Samples were prepared by cold isostatic pressing at 80 MPa. Dense and fully perovskite 0.575[0.5PMN–0.5PYbN]–0.425PT ceramics were fabricated at 975°C for 4 h, and these samples displayed a remnant polarization ( P _r) of 32 μ C/cm², coercive field ( E _c) of 17 kV/cm, and a piezoelectric charge coefficient ( d ₃₃) of 475 pC/N. It is proposed that this ternary system can be tailored for various applications.     

Mechanochemical Synthesis of 0.9[0.6Pb(Zn1/3Nb2/3)O3·0.4Pb(Mg1/3Nb2/3)O3]·0.1PbTiO3

Lead zinc niobate–lead magnesium niobate–lead titanate (PZN–PMN–PT) ceramic powders of perovskite structure have been prepared via a mechanochemical processing route. A single-phase perovskite powder of ultrafine particles in the nanometer range was successfully synthesized when a MZN powder (columbite precursor) was mechanically activated for 10 h together with mixed lead and titanium oxides. The following steps are involved when the ternary oxide mixture is subjected to an increasing degree of mechanical activation. First, the starting materials are significantly refined in particle size as a result of the continuous deformation, fragmentation and then partially amorphized at the initial stage of mechanical activation. This is followed by the formation of perovskite nuclei and subsequent growth of these nuclei in the activated oxide matrix with increasing activation time. When calcined at various temperatures in the range of 500–800°C, pyrochlore phase was not detected by XRD phase analysis in the mechanochemically synthesized powder. Only a minor amount (∼2%) of pyrochlore phase was observed when the calcination temperature was raised to 850°C. The PZN–PMN–PT derived from the mechanochemically synthesized powder can be sintered to ∼98% relative density at a sintering temperature of 950°C. The PZN–PMN–PT sintered at 1100°C for 1 h exhibits a dielectric constant of ∼18 600 and a dielectric loss of 0.015 at the Curie temperature of 112°C when measured at a frequency of 0.1 kHz, together with a d ₃₃ value of 323 ×10⁻¹² pC/N.     

Synthesis of Pyrochlore-Free 0.9Pb(Mg1/3Nb2/3)O3-0.1PbTiO3 Ceramics via a Soft Mechanochemical Route

Single-phase perovskite 0.9Pb(Mg_1/3Nb_2/3)O₃-0.1PbTiO₃ (0.9PMN–0.1 PT) from a stoichiometric mixture of starting materials was synthesized by applying a mechanochemical technique to the stage of a precursor. A stoichiometric mixture of PbO, TiO₂, Mg(OH)₂, and Nb₂O₅ was milled for 60 min and heated at temperatures as low as 850°C for 4 h to obtain a single phase. The maximum dielectric constant of the samples from the milled mixture increased as the sintering temperature increased, with the remarkable grain growth, and attained 24600 at 1200°C. In contrast, poor densification and coexistence of the pyrochlore phase were observed on the samples from the nonmilled mixture. Further observation suggested that the pyrochlore phase concentrated near the surface during sintering and then migrated into the PbZrO₃ packing powder, leading to a pyrochlore–free phase at 1250°C. The dielectric constant of the latter ceramics was explained by the series mixing rule for the dielectric constant of a diphasic solid.     

High Strain, 〈001〉 Textured 0.675Pb(Mg1/3Nb2/3)O3–0.325PbTiO3 Ceramics: Templated Grain Growth and Piezoelectric Properties

Lead magnesium niobate–lead titanate, 0.675Pb(Mg_1/3Nb_2/3)O₃–0.325PbTiO₃ (PMN–32.5PT) ceramics were textured (grain-oriented) in the 〈001〉-crystallographic direction by the templated grain growth process. The textured PMN–32.5PT ceramics were produced by orienting {001}-SrTiO₃ (ST) platelets (∼10 μm in diameter and ∼2-μm thickness) in a submicron PMN–32.5PT matrix. The templated growth of 〈001〉-oriented PMN–32.5PT grains on the ST platelets resulted in textured ceramics with ∼70% Lotgering factor and >98% theoretical density. Unlike most lead-based ceramics, excess PbO was not needed for sintering or grain growth. Based on unipolar stain-field measurements at 0.2 Hz, the textured samples displayed >0.3% strain at 50 kV/cm. Low-field d ₃₃-coefficients of >1600 pC/N (<5 kV/cm) were measured directly from unipolar measurements. The low drive field d ₃₃-piezoelectric coefficient of the highly textured samples is two times greater than polycrystalline PMN–32.5PT.     

Thermal Expansion of Homogeneous and Gradient Solid Solutions in the System KZr2(PO4)3─KTi2(PO4)3

Low-thermal-expansion ceramics having arbitrary thermal expansion coefficients were synthesized from homogeneous solid solutions in the system KZr₂(PO₄)₃─KTi₂(PO₄)₃ (KZP–KTP). Dense and strong ceramics were fabricated by sintering at 1100° to 1200°C with 2 wt% MgO. The thermal expansion coefficient increased from 0 to +3 × 10⁻⁶/°C with increasing x in KZr_{2 − x}Ti_x (PO₄)₃ (KZTP). In addition, a functionally gradient material with respect to thermal expansion was prepared by forming a series of KZTP solid solutions in a single ceramic body. By heating a pile of KZP and KTP ceramics in contact with each other, KZP and KTP bonded together to form a KZTP gradient solid solution near the interface.     

A Polyethylene Glycol-Modified Solid-State Reaction Route to Synthesize Relaxor Ferroelectric Pb(Mg1/3Nb2/3)O3–PbTiO3 (PMN–PT)

By introducing polyethylene glycol (PEG) to the conventional simultaneously mixed oxide reaction route, the 0.65Pb(Mg_1/3Nb_2/3)–0.35PbTiO₃ (0.65PMN–0.35PT) powders and ceramics with pure perovskite phase have been successfully synthesized. It is found that PEG interacts with PbO oxide in a way favoring the formation of the desired perovskite phase. As a result, pyrochlore-free 0.65PMN–0.35PT powders are synthesized at a low temperature of 850°C. The ceramics sintered at 1000°C show uniform grains with the size ranging from 1 to 3 μm. The room temperature dielectric constant is 3440. The maximum dielectric constant is 16 220 at 1 kHz. This method can be applied to the synthesis of other Pb-containing and Bi-containing ferroelectric materials, especially the relaxor-type ferroelectrics in which the pyrochlore phase is difficult to eliminate.     

Fabrication of Transparent, Sintered Sc2O3 Ceramics

We report here the fabrication of transparent Sc₂O₃ ceramics via vacuum sintering. The starting Sc₂O₃ powders are pyrolyzed from a basic sulfate precursor (Sc(OH)_2.6(SO₄)_0.2·H₂O) precipitated from scandium sulfate solution with hexamethylenetetramine as the precipitant. Thermal decomposition behavior of the precursor is studied via differential thermal analysis/thermogravimetry, Fourier transform infrared spectroscopy, X-ray diffractometry, and elemental analysis. Sinterability of the Sc₂O₃ powders is studied via dilatometry. Microstructure evolution of the ceramic during sintering is investigated via field emission scanning electron microscopy. The best calcination temperature for the precursor is 1100°C, at which the resultant Sc₂O₃ powder is ultrafine (∼85 nm), well dispersed, and almost free from residual sulfur contamination. With this reactive powder, transparent Sc₂O₃ ceramics having an average grain size of ∼9 μm and showing a visible wavelength transmittance of ∼60–62% (∼76% of that of Sc₂O₃ single crystal) have been fabricated via vacuum sintering at a relatively low temperature of 1700°C for 4 h.     

Effect of Bi2O3 Addition on the Sintering Temperature and Microwave Dielectric Properties of Zn2SiO4 Ceramics

Bi₂O₃ was added to a nominal composition of Zn_1.8SiO_3.8 (ZS) ceramics to decrease their sintering temperature. When the Bi₂O₃ content was <8.0 mol%, a porous microstructure with Bi₄(SiO₄)₃ and SiO₂ second phases was developed in the specimen sintered at 885°C. However, when the Bi₂O₃ content exceeded 8.0 mol%, a liquid phase, which formed during sintering at temperatures below 900°C, assisted the densification of the ZS ceramics. Good microwave dielectric properties of Q × f =12,600 GHz, ɛ_r=7.6, and τ_f=−22 ppm/°C were obtained from the specimen with 8.0 mol% Bi₂O₃ sintered at 885°C for 2 h.     

Preparation and Sintering Behavior of Fine-Grained A12O3-SiO2 Composite

A fine, uniform A1₂O₃-SiO₂ powder was prepared by heterocoagulation of narrow Al₂O₃ and SiO₂ powders. This composite powder was dispersed, compacted, and fired in air at 900° to 1580°C for 1 to 13 h. Full density was achieved at 1550°C with the formation of a mullite phase. Relative densities of 83% and 98% (0.3 μm grain size) were measured for samples sintered at 1200°C for 13 h and at 1400°C for 1 h, respectively.     

Low-Temperature Sintering of K0.5Na0.5NbO3 Ceramics

The objective of this work was to lower the sintering temperature of K_0.5Na_0.5NbO₃ (KNN) without reducing its piezoelectric properties. The KNN was sintered using 0.5, 1, 2, and 4 mass% of (K, Na)-germanate. The influence of the novel sintering aid, based on alkaline germanate with a melting point near 700°C, on the sintering, density, and piezoelectric properties of KNN is presented. The alkaline-germanate-modified KNN ceramics reach up to 96% of theoretical density at sintering temperatures as low as 1000°C, which is approximately 100°C less than the sintering temperature of pure KNN. The relative dielectric permittivity (ɛ/ɛ₀) and losses (tanδ), measured at 10 kHz, the piezo d ₃₃ coefficient, the electromechanical coupling and mechanical quality factors ( k _p, k _t, Q _m) of KNN modified with 1 mass% of alkaline germanate are 397, 0.02, 120 pC/N, 0.40, 0.44, and 77, respectively. These values are comparable to the best values obtained for KNN ceramics sintered above 1100°C.     

Low-Temperature Firing and Microwave Dielectric Properties of Ca[(Li1/3Nb2/3)0.84Ti0.16]O3−δ Ceramics for LTCC Applications

The effects of LiF and ZnO–B₂O₃–SiO₂ (ZBS) glass combined additives on phase composition, microstructures, and microwave dielectric properties of Ca[(Li_1/3Nb_2/3)_0.84Ti_0.16]O_3−δ (CLNT) ceramics were investigated. The LiF and ZBS glass combined additives lowered the sintering temperature of CLNT ceramics effectively from 1150° to 880°C. The main diffraction peaks of all the specimens split due to the coexistence of the non-stoichiometric phase (A) and stoichiometric phase (B), which all possess CaTiO₃-type perovskite structures. The transformation from A into B became accelerated with the increase of LiF or ZBS content. ZBS glass restrained the volatilization of lithium salt, which greatly affected the microstructures and microwave dielectric properties. CLNT ceramics with 2 wt% LiF and 3 wt% ZBS sintered at 900°C for 2 h show excellent dielectric properties: ɛ_r=34.3, Q × f =17 400 GHz, and τ_f=−4.6 ppm/°C. It is compatible with Ag electrodes, which makes it a promising ceramic for low-temperature cofired ceramics technology application.     

Ferroelectric 90° Domain Evaluation in Tetragonal Pb(Mg1/3Nb2/3)O3–PbTiO3 Ceramics

The domain structure of ferroelectrics changes during poling has a direct influence on the macroscopic properties of the materials. The intensity variation of the different X-ray diffraction (XRD) pattern profiles was used to identify the percentage of 90° domain reorientation in the tetragonal phase of Pb(Mg_1/3Nb_2/3)O₃–PbTiO₃ (PMN–PT) ceramics after poling. The results are consistent with the change of piezoelectric properties. In addition, by using XRD patterns, a spatial distribution of polarization in a well-poled 0.62PMN–0.38PT ceramics has been determined and was found to be best described by the Cauchy function W _00l (φ)=1/(1+0.023φ²).     

Synthesis of Pb(Mg1/3Nb2/3)O3 in Excess Lead Oxide by Mechanical Activation

Twenty hours of mechanical activation of mixed oxides at room temperature led to the formation of Pb(Mg_1/3Nb_2/3)O₃ (PMN) in excess PbO. The crystallinity of the activation-derived perovskite PMN phase was further established when the activated PMN–PbO phase mixture was subjected to calcination at 800°C. Pyrochlores, such as Pb₃Nb₄O₁₃ and Pb₂Nb₂O₇, were not observed as transitional phases on mechanical activation and subsequent calcination, although 50% excess PbO was deliberately added. The perovskite PMN phase was recovered by washing off excess PbO using acetic acid solution at room temperature. It was sintered to a relative density of 98.9% of theoretical at 1200°C for 1 h and the sintered PMN exhibited a dielectric constant of ∼14 000 at 100 Hz and a Curie temperature of −11°C.     

Low-Temperature Sintering and Piezoelectric Properties of (Na0.5K0.5)NbO3 Lead-Free Piezoelectric Ceramics

(Na_0.5K_0.5)NbO₃ (NKN) ceramic with 1.5 mol% CuO added (NKNC) was well sintered even at a low temperature of 900°C with the addition of ZnO. Most of the ZnO reacted with the CuO and formed the liquid phase that assisted the densification of the specimens at 900°C. A few Zn²⁺ ions entered the matrix of the specimens and increased the coercive field ( E _c) and Q _m values of the specimens. High-piezoelectric properties of k _p=0.37, Q _m=755, and ɛ₃ ^T /ɛ₀=327 were obtained from the NKNC ceramics containing 1.0 mol% ZnO sintered at 900°C for 2 h.     

Microwave Dielectric Properties of Li2TiO3 Ceramics Doped with ZnO–B2O3 Frit

A type of new low sintering temperature ceramic, Li₂TiO₃ ceramic, has been found. Although it is difficult for the Li₂TiO₃ compound to be sintered compactly at temperatures above 1000°C for the volatilization of Li₂O, dense Li₂TiO₃ ceramics were obtained by conventional solid-state reaction method at the sintering temperature of 900°C with the addition of ZnO–B₂O₃ frit. The sintering behavior and microwave dielectric properties of Li₂TiO₃ ceramics with less ZnO–B₂O₃ frit (≤3.0 wt%) doping were investigated. The addition of ZnO–B₂O₃ frit can lower the sintering temperature of the Li₂TiO₃ ceramics, but it does not apparently degrade the microwave dielectric properties of the Li₂TiO₃ ceramics. Typically, the good microwave dielectric properties of ɛ_r=23.06, Q × f =32 275 GHz, τ_f = 35.79 ppm/°C were obtained for 2.5 wt% ZnO–B₂O₃ frit-doped Li₂TiO₃ ceramics sintered at 900°C for 2 h. The porosity was 0.08%. The Li₂TiO₃ ceramic system may be a promising candidate for low-temperature cofired ceramics applications.     

Influence of V2O5 Additions to 5Li2O–1Nb2O5–5TiO2 Ceramics on Sintering Temperature and Microwave Dielectric Properties

The effects of the addition of V₂O₅ on the sintering behavior, microstructure, and microwave dielectric properties of 5Li₂O–1Nb₂O₅–5TiO₂ (LNT) ceramics have been investigated. With low-level doping of V₂O₅ (≤3 wt%), the microstructure of the LNT ceramic changed from a special two-level intergrowth structure into a two-phase composite structure with separate grains. And the sintering temperature of the LNT ceramics could be lowered to around 900°C by adding a small amount of V₂O₅ without much degradation in microwave dielectric properties. Typically, better microwave dielectric properties of ɛ_r=41.7, Q × f =7820 GHz, and τ _f =45 ppm/°C could be obtained for the 1 wt% V₂O₅-doped ceramics sintered at 900°C.