In situ co-precipitation synthesis and photoluminescence of YxGd1−xVO4:Tm microcrystalline phosphors by hybrid precursors

Y_xGd_1−xVO₄:Tm³⁺ (5 mol%) phosphors were prepared by in situ co-precipitation technology with the different content ratio of Y/Gd (x = 0.2, 0.3, 0.4, 0.5, 0.6, 0.8, respectively). During the process, rare earth coordination polymers with o-hydroxylbenzoate were used as precursors, composing with polyethylene glycol (PEG) as dispersing media. After heat-treatment of the resulting multicomponent hybrid precursors at 900 °C, the samples were obtained. SEM indicated the particles present good crystalline state, whose crystalline grain sizes were about 0.2–2 μm. Under the excitation of 257 nm, all the materials show the characteristic emission of Tm³⁺ which is the strong blue emission centered at 475 nm originating from ¹G₄ → ³H₆ of Tm³⁺. Besides this, concentration quenching appears in the system of YVO₄:Tm³⁺ and GdVO₄:Tm³⁺. And when x reaches 0.5, the system of Y_xGd_1−xVO₄:Tm³⁺ shows the strongest blue emission.     

Sintering behavior and microwave dielectric properties of Bi3(Nb1−xTax)O7 solid solutions

Solid solutions of Bi₃(Nb_1−xTa_x)O₇ (x = 0.0, 0.3, 0.7, 1) were synthesized using solid state reaction method and their microwave dielectric properties were first reported. Pure phase of fluorite-type could be obtained after calcined at 700 °C (2 h)⁻¹ between 0 ≤ x ≤ 1 and Bi₃(Nb_1−xTa_x)O₇ ceramics could be well densified below 990 °C. As x increased from 0.0 to 1.0, saturated density of Bi₃(Nb_1−xTa_x)O₇ ceramics increased from 8.2 to 9.1 g cm⁻³, microwave permittivity decreased from 95 to 65 while Q_f values increasing from 230 to 560 GHz. Substitution of Ta for Nb modified temperature coefficient of resonant frequency τ_f from −113 ppm °C⁻¹ of Bi₃NbO₇ to −70 ppm °C⁻¹ of Bi₃TaO₇. Microwave permittivity, Q_f values and τ_f values were found to correlate strongly with the structure parameters of fluorite solid solutions and the correlation between them was discussed in detail. Considering the low densified temperature and good microwave dielectric proprieties, solid solutions of Bi₃(Nb_1−xTa_x)O₇ ceramics could be a good candidate for low temperature co-fired ceramics application.     

Optical properties of a-(Se70Te30)100−x(Se98 Bi2)x thin films

Measurements of optical constants (absorption coefficient, refractive index, extinction coefficient, real and imaginary part of the dielectric constant) have been made on a-(Se₇₀Te₃₀)_100−x (Se₉₈Bi₂)_x thin films (where x=0, 5, 10, 15 and 20) of thickness 2000 Å in the wavelength range 450–1000 nm. It is found that the optical bandgap decreases with the increase of Se₉₈Bi₂ concentration in the a-(Se₇₀Te₃₀)_100−x(Se₉₈Bi₂)_x system. The value of refractive index (n) decreases, while the extinction coefficient (k) increases with increasing photon energy. The results are interpreted in terms of concentration of localized states varying effective Fermi level.     

Spectroscopic evidence of inhomogeneous distribution of Nd in YVO4, YPO4 and YAsO4 crystals

Nd³⁺ : YVO₄ is one of the most interesting laser hosts for micro and diode-pumped solid state lasers. We have studied magnetic and optical properties of Nd³⁺ in three zircon type crystals YMO₄ (M=V, As, P). In particular, Nd³⁺ ions exhibit in the three hosts a multisite character observed in the absorption and emission spectra. However, the emission and its dynamics are strongly dependant on the reabsorption mechanisms. In Nd : YVO₄, single crystals containing 7 ± 1 × 10¹⁸ Nd³⁺ ions/cm³, the lifetime is 95 ± 2 μs in good agreement with the calculated radiative lifetime. Electron Paramagnetic Resonance (EPR) measurements are performed to identify the nature of the different substitution sites for Nd³⁺ ions. Nd³⁺ ions are found to be inhomogeneously distributed in tetragonal D_2d symmetry sites, in isolated ions, “shallow clusters” and pairs. Proportions of the different local environments depend on the total neodymium concentration. For instance, 15% of the Nd³⁺ ions are gathered in Nd³⁺–Nd³⁺ pairs for 7.2 ± 0.2 × 10¹⁹ Nd³⁺ ions/cm³.     

Optical properties and energy transfer among Nd in Nd:Ca2Al2SiO7 crystals for diode pumped lasers

The energy levels of neodymium in the Nd³⁺:Ca₂Al₂SiO₇ (CAS) laser material with gehlenite structure are reported. As the Nd³⁺:Ca₂Al₂SiO₇ compound presents a broad absorption around 806 nm, it is a good candidate for diode pumped laser. The ⁴F_3/2→⁴I_9/2 and ⁴F_3/2→⁴I11/2 emission have been recorded and the fluorescence branching ratios calculated from the Judd-Ofelt analysis are 0.41 and 0.47 respectively. The emission cross section at 1.06 μm (⁴F_3/2→⁴I11/2 transition) is 5 × 10^-20 cm². The decay profiles of the Nd³⁺ emission have been analyzed for several Nd³⁺ concentrations using the kinetic microparameters related to the cross relaxation ( and R₀≈6 Å) and the energy migration probabilities ( ). In the Nd:CAS laser material, the optimal concentration corresponding to the maximum of the fluorescence intensity is determined to be around 2.7 × 10²⁰ Nd³⁺ ions cm^-3. The Nd³⁺-Nd³⁺ interactions are not very strong in this material as the optical concentration value is two times higher than in the Nd:YAG laser material.     

Epitaxial grown K1−xRbxTiOPO4 films with extremely flat surfaces for waveguiding

We report on epitaxial {1 0 0} K_1−xRb_xTiOPO₄ waveguide films for the visible spectral range grown on KTiOPO₄ substrates by liquid phase epitaxy. Using the m-line technique a refractive index increase of Δn_x≈0.007 and Δn_z≈0.004 for TM and TE polarisation has been determined for a K_0.78Rb_0.22TiOPO₄ film. Optical transmission and nearfield distribution are comparable to conventional ion-exchanged waveguides. Typical attenuation of about 1 dB/cm for both TM and TE polarisation was obtained at λ=532 and 1064 nm. Energy-dispersive X-ray spectrometry reveals solid-solution films with graded rubidium composition profiles. X-ray rocking curve analyses confirm the epitaxial growth process and indicate perfect and relaxed K_1−xRb_xTiOPO₄ films. Atomic force microscopy investigations reveal regular step structures with step heights Δh<1.3 nm resulting in rms-roughness values of ≈0.4 nm.     

Optical and electrical properties of p-type AgInSnxS2−x (x = 0–0.04) thin films prepared by spray pyrolysis

AgInSn_xS_2−x (x = 0–0.2) polycrystalline thin films were prepared by the spray pyrolysis technique. The samples were deposited on glass substrates at temperatures of 375 and 400 °C from alcoholic solutions comprising silver acetate, indium chloride, thiourea and tin chloride. All deposited films crystallized in the chalcopyrite structure of AgInS₂. A p-type conductivity was detected in the Sn-doped samples deposited at 375 °C, otherwise they are n-type. The optical properties of AgInSn_xS_2−x (x < 0.2) resemble those of chalcopyrite AgInS₂. Low-temperature PL measurements revealed that Sn occupying an S-site could be the responsible defect for the p-type conductivity observed in AgInSn_xS_2−x (x < 2) thin films.     

High-resolution and analytical transmission electron microscopy of epitaxial YBa2Cu3O7−x thin films and YBa2Cu3O7/PrBa2Cu3O7 superlattices

Transmission electron microscopy (TEM) studies of epitaxial YBa₂Cu₃O_7−x thin films and YBa₂Cu₃O₇/PrBa₂Cu₃O₇ superlattices are summarized. High-resolution imaging of cross-sections and plan views and energy-dispersive X-ray microanalysis and electron energy loss spectroscopy in the transmission electron microscope were the methods applied. In the first section results on YBa₂Cu₃O_7−x thin films With varying oxygen stoichiometry deposited onto SrTiO₃ are discussed. Then, YBa₂Cu₃O₇/PrBa₂Cu₃O₇ superlattices deposited onto SrTiO₃ and MgO are investigated. Finally, an interface analysis of high-quality YBa₂Cu₃O_7−x thin films deposited onto sapphire with yttrium-stabilized zirconia buffer layers is presented.     

Transmission electron microscopy of annealed a-Si1−xCx:H/Al films with different Al grain sizes

The crystallization behavior of a-Si_1−xC_x:H/Al films after annealing has been investigated by transmission electron microscopy and Raman scattering. It is found that the crystallization process is complex and non-uniform, and that both equiaxial and branching Si grains with many twins and stacking faults arise at annealing temperatures as low as 250 °C. Both fine polycrystalline β-SiC grains and fractal-like -SiC aggregates are first observed in a few regions in a-Si_1−xC_x:H/Al films annealed at 350 °C. The increase of the Al grain size can cause a decrease in the crystallization temperature and a rise in the grain growth rate of Si. At higher annealing temperatures, the reaction process SiC+Al→Al₄C₃+Si is predominant.     

Bond-lengths of the atomic nearest-neighbor and next-nearest-neighbor in A1−xBxC1−yDy III–V solid solutions

On the basis of the FDUC model and the hypothesis of the constant covalent radii, the expressions of the atomic nearest-neighbor and the next-nearest-neighbor bond-lengths were derived for A_1−xB_xC_1−yD_y III–V quaternary solid solutions. This set of bond-length expressions predicts the averaged bond-lengths and bond angles at any concentration (x, y) for the III–V pseudobinary and quaternary solid solutions, which are only dependent on the lattice parameters and the concentrations of the pure end compounds. When x=0, 1 or y=0, 1, A_1−xB_xC_1−yD_y III–V quaternary solid solutions degenerate into the relative pseudobinary solid solutions, in which the nearest-neighbor and the next-nearest-neighbor bond-lengths agree well with the experimental results. Further discussion and comparison with other theoretical models are also given in this paper.     

Strong magnetoelastic effect in Pr1−xCaxMnO3

Manganese oxides with distorted perovskite structure have attracted much attention during the last decade due to their colossal magnetoresistance (CMR), and the strong correlations among the various degrees of freedom involved. In particular, Pr_1−xCa_xMnO₃ compounds present in a wide Ca-doping range a charge ordering phenomenon, consisting of real space ordering of Mn³⁺ and Mn⁴⁺ in alternate lattice sites below a certain temperature T_CO. This ordering brings about a lattice distortion and a large hardening of the sound velocity below T_CO. Tomioka et al. have observed that an applied magnetic field can melt this charge ordered state and induce a transition from an insulating to a metallic state. In order to study the effects of this charge order melting, ultrasonic longitudinal sound velocity measurements were performed on polycrystalline Pr_1−xCa_xMnO₃ (x=0.35 and 0.5) as a function of magnetic field and temperature. Interesting anomalies were found related to the melting of the charge ordered phase into a metal-like state even at low temperatures.     

Optical band gap studies on xPb3O4–(1−x)P2O5 lead[(II, IV)] phosphate glasses

A series of glasses in the xPb₃O₄–(1−x)P₂O₅ (red lead phosphate) (RLP) system with ‘x' varying from 0.075 to 0.4 were prepared by the single-step melt quenching process from Pb₃O₄ and NH₄H₂PO₄. The optical absorption spectra of these glasses have been recorded in the ultraviolet region from 200 to 400 nm and the fundamental absorption edges have been identified. The optical band gap E_opt values have been determined for all the glasses using the known theories. The (E_opt) values vary from 4.90 to 3.21 eV the highest being 4.57 eV, corresponding to the most stable glass of x=0.225. The absorption edge is attributed to the indirect transitions and the origin of the Urbach energy ΔE is suggested to be thermal vibrations. These glasses promise as potential candidates for application in optical technology compared to simple xPbO–(1−x)P₂O₅ (lead phosphate) (LP) glasses.     

Spectroscopic and lasing properties of a diode pumpable Nd:GdF3 crystal

A Nd:GdF₃ single crystal is investigated in terms of absorption and emission properties. It is found that the absorption spectrum around 796 nm has a bandwidth broader than in Nd:YAG or Nd:YLF. As a matter of fact, the absorption band is well fitted to the emission of AlGaAs pump diodes. In the 1050 to 1070 nm region, the emission spectrum is strongly polarized and high peaks are observed at 1051 and 1064 nm. Room-temperature laser emission was achieved under Ti:sapphire pumping for different orientations of the Nd:GdF₃ crystal. An optical efficiency of 25% with a 33% slope efficiency was measured. Then Nd:GdF₃ could be a serious candidate for microlaser applications compared to standard materials like Nd:YVO₄.     

Optical transitions near the band edge in bulk CuInxGa1−xSe2 from ellipsometric measurements

From the analysis of the variation of optical absorption coefficient with incident photon energy between 0.8 and 2.6 eV, obtained from ellipsometric data, the energy E_G of the fundamental absorption edge and E_G′ of the forbidden direct transition for CuIn_xGa_1−xSe₂ alloys are estimated. The change in E_G and the spin-orbit splitting Δ_SO=E_G′−E_G with the composition x can be represented by parabolic expression of the form E_G(x)=E_G(0)+ax+bx² and Δ_SO(x)=Δ_SO(0)+a′x+b′x², respectively. b and b′ are called “bowing parameters”. Theoretical fit gives a=0.875 eV, b=0.198 eV, a′=0.341 eV and b′=−0.431 eV. The positive sign of b and negative sign of b′ are in agreement with the theoretical prediction of Wei and Zunger [Phys. Rev. B 39 (1989) 6279].     

Mechanical characterization of Ni1−xZnxFe2O4 prepared by non-conventional methods

The mechanical properties like hardness, H_v and compressive strength, σ of Ni_1−xZn_xFe₂O₄ (x = 0.2, 0.3, 0.4 and 0.5) prepared by the non-conventional flash combustion and citrate-gel decomposition techniques are studied and reported. It is observed that there is an increase in hardness with zinc content as well as sintering temperature. The hardness in the order of 2.0–3.63 GPa and compressive strength in the order of 150–240 MPa are obtained for Ni–Zn ferrites prepared by these non-conventional techniques. The influence of density, porosity and microstructure on hardness and compressive strength of Ni–Zn ferrites with respect to sintering temperature was studied.     

Synthesis and humidity sensitive properties of nanocrystalline Ba1−xSrxTiO3 thick films

Nanocrystalline Ba_1−xSr_xTiO₃ (x=0, 0.2, 0.4, 0.6, 0.8 and 1.0) precursors were synthesized using the stearic acid gel method. After the precursors had been calcined at 600–950°C for 0.5–1 h, nanocrystalline powders with the cubic perovskite structure were obtained and these were made into thick films. The powder samples were characterized by differential thermal analysis, X-ray diffraction and transmission electron microscopy, and the thick film samples were characterized by scanning electron microscopy and X-ray diffraction. The humidity-sensitive properties of the nanocrystalline Ba_1−xSr_xTiO₃ thick films were investigated. The results show that these nanocrystalline thick films possess higher humidity sensitivity and lower resistance than those of conventional materials.     

Doping and electrical characteristics of in-situ heavily B-doped Si1−x−yGexCy films epitaxially grown using ultraclean LPCVD

Doping and electrical characteristics of in-situ heavily B-doped Si_1−x−yGe_xC_y (0.22<x<0.6, 0<y<0.02) films epitaxially grown on Si(100) were investigated. The epitaxial growth was carried out at 550°C in a SiH₄–GeH₄–CH₃SiH₃–B₂H₆–H₂ gas mixture using an ultraclean hot-wall low-pressure chemical vapor deposition (LPCVD) system. It was found that the deposition rate increased with increasing GeH₄ partial pressure, and only at high GeH₄ partial pressure did it decrease with increasing B₂H₆ as well as CH₃SiH₃ partial pressures. With the B₂H₆ addition, the Ge and C fractions scarcely changed and the B concentration (C_B) increased proportionally. The C fraction increased proportionally with increasing CH₃SiH₃ partial pressures. These results can be explained by the modified Langmuir-type adsorption and reaction scheme. In B-doped Si_1−x−yGe_xC_y with y=0.0054 or below, the carrier concentration was nearly equal to C_B up to approximately 2×10²⁰ cm⁻³ and was saturated at approximately 5×10²⁰ cm⁻³, regardless of the Ge fraction. The B-doped Si_1−x−yGe_xC_y with high Ge and C fractions contained some electrically inactive B even at the lower C_B region. Resistivity measurements show that the existence of C in the film enhances alloy scattering. The discrepancy between the observed lattice constant and the calculated value at the higher Ge and C fraction suggests that the B and C atoms exist at the interstitial site more preferentially.     

Determination of the E1 and E1+Δ1 energy bands by photoreflectance in AlxGa1−xAs in the region 0<x<0.55

The E₁ and E₁+Δ₁ energy bands of metal–organic chemical vapor deposition grown Al_xGa_1−xAs, with x in the range 0–0.55, have been determined using photoreflectance technique. The aluminum composition for each sample was determined using the energy of the room-temperature photoluminescence compensated peak value and a suitable fundamental band gap formula. The positions of the E₁ and E₁+Δ₁ peaks were determined from curve-fitting an appropriate theoretical model to our experimental data by a modified downhill simplex method. Using the results, we propose new E₁ and E₁+Δ₁ cubic expressions as functions of the aluminum composition, x, and compare them with the available reported expressions.     

Preparation and photoelectrochemical properties of Ti1−xVxO2 solid solution thin film photoelectrodes with gradient bandgap

A design of a gradient bandgap Ti_1−xV_xO₂ thin film electrode for wet-type solar cells is provided. The gradient bandgap film electrodes were prepared by heating stacked layers of varying V/Ti ratios using the sol-gel method. A composition gradient was observed for some of the samples by X-ray photoelectron spectroscopy although it was not very large. For the Ti_1−xV_xO₂ film electrodes, conspicuous visible light photoresponse and photoelectrochemical stability were observed. The photocurrent increased with increasing bias potential. However, the photocurrent onset potentials of the Ti_1−xV_xO₂ film electrodes were more positive than those of TiO₂ film electrodes, probably owing to the high surface state density introduced by the diffusion of vanadium ions.     

Spectroscopic analysis and the effects of color centers on the laser performance of Nd: CaZn2Y2Ge3O12

Spectroscopic and EPR investigations of Nd³⁺-doped CaZn₂Y₂Ge₃O₁₂ (CAZGAR) have been performed. The absorption, fluorescence, excitation spectra and fluorescence lifetime have been measured at room temperature. The Judd-Ofelt theory has been applied to the measured optical absorption intensities to predict the radiative decay rates, branching ratios, and peak stimulated emission cross section from the metastable ⁴F_3/2 state to the ⁴I_9/2 manifold. The fluorescence lifetime of the ⁴F_3/2 level of Nd³⁺ at low concentration in this host was measured to be 285 ± 10 μs, which is longer than that for Nd³⁺: YAG. Color centers located at zinc octahedral sites have been produced in these crystals by ultraviolet irradiation and have been detected by EPR techniques. The effects of the color centers on the potential laser characteristics of this materials are discussed.